Search Documents

By K. F. Unrug

The concept of bolting mine roofs to prevent roof falls was initiated in the 1950's and was quickly accepted by the mining industry because it was inexpensive, effective and convenient. The principle regarding roof bolting were that: a) the loose and fragmented rocks were suspended from or clamped to more competent surrounding rock and b) generally, by clamping several layers of thin and laminated strata, a more competent monolithic beam is created.

Jan 1, 1991

By Reinhard F. Dobner

After a short introduction about the HK's secondary smelter process and explanations concerning the anodes produced the regulation and buffering of bleed will be described and the principles of technology for processing of bleed will be presented. Modernization aspects, especially installation equipment, and the different types of evaporators used will be described in detail. Besides, experience made with acid-resistant materials - stainless steel, enamel, plastics - will be reported. Environmental aspects such as water and air pollution will be outlined briefly and in conclusion the quality of products obtained as well as quality control will be presented.

Jan 1, 1997

One of the most common critical areas of longwall mining in terms of ground stability are the gateroad and bleeder entries. These critical entries provide much-needed safe access for miners and allow for adequate ventilation required for dilution of hazardous airborne contaminants and must remain open during mining of a multi-panel district. This paper focuses on the stability of the longwall entries subjected to a single abutment load such as bleeders, first tailgate, and last headgate. First tailgate and last headgate are also referred to as blind headgates and tailgates. A study of a longwall district through conditions mapping, support evaluations, and numerical modeling was conducted and evaluated by researchers from the National Institute for Occupational Safety and Health (NIOSH). The condition mapping and support evaluations were performed on entries that spanned the previous five years of mining and relied on a diverse selection of supports to maintain the functionality of the entry. Numerical modeling was also conducted to evaluate various support types with further investigation and comparison to the condition mapping. The study demonstrated the importance of the abutment load decay versus distance from the gob edge, the potential for a reduction in material handling related injuries, as well as optimal usage of secondary and standing support.

Jan 7, 2020

By John E. Urosek, Dennis A. Beiter, William J. Francart

In This Chapter [Designing bleeder systems Examining and maintaining bleeder systems Evaluating bleeder system effectiveness] INTRODUCTION Bleeder systems are that part of the mine ventilation network used to ventilate pillared areas in underground coal mines. Pillared areas are those in which pillars have been wholly or partially removed, including the areas where coal has been extracted by longwall mining. Bleeder systems protect miners from the hazards associated with methane and other gases, dusts and fumes, and oxygen deficiency that may occur in these mined-out areas. Effective bleeder systems control the air passing through the area and continuously dilute and move any methane-air mixtures and other gases, dusts, and fumes from the worked-out area away from active workings and into a return air course or to the surface of the mine. A bleeder system includes the pillared area (including the internal airflow paths), bleeder entries, bleeder connections, and all associated ventilation control devices that control the air passing through the pillared area. Bleeder entries are special air courses designed and maintained as part of the mine ventilation system. [This chapter focuses on the design, examination, maintenance, and evaluation of bleeder systems in underground coal mines.] The history of coal mine explosions in the United States is a reminder of the importance of adequate ventilation. Some of those disasters were the result of inadequately ventilated pillared areas. The importance of developing bleeder systems to ventilate these pillared areas and evaluating the bleeder system’s effectiveness is reflected in present-day federal regulations. For more information on bleeder systems, see Tisdale [1996] and Urosek and Francart [2002].

Jan 6, 2006

The BLEG (Bulk Leach Extractable Gold) technique is a semiquantitative measure of cyanide extractable gold contained in a sample. A 5kg sample is leached in cyanide solution for 24 hours and gold is precipitated out of the pregnant solution using zinc and assayed by AAS. The detection limit is reported as ppb (parts per billion). Telfer is located 1300km north north-east from Perth in the Great Sandy Desert. The climate is one of hot summers with irregular rainfall and mild winters. A large portion of the area is covered by aeolian sand and seif dunes with poorly developed drainage, rare outcrop; topographic relief is a maximum of 96m. Poor outcrop and poorly developed drainage render conventional stream sediment sampling and soil geochemistry inadequate. Therefore a technique providing a minimum number of samples with maximum accuracy and sensitivity was needed. Consequently BLEG orientation surveys were conducted over the Telfer Mine area in 1983, 1984 and 1985.

Jan 1, 1988

By Raquel Dei Agnoli

Membranas a base de polímeros perfluorosulfonados, como o Nafion® (DuPont), vêm sendo extensivamente usadas como membrana de troca protônica em células a combustível. Contudo, o elevado custo e a baixa condutividade em temperaturas superiores a 80oC restringem o uso destes dispositivos. Em opção ao uso da membrana Nafion®, membranas a base da blenda polindeno sulfonado/polifluoreto de vinilideno (SPInd/PVDF) foram desenvolvidas, investigando o efeito da composição na performance das membranas. As membranas foram produzidas por evaporação de solvente da solução dos polímeros precursores. As blendas foram caracterizadas por termogravimetria e calorimetria exploratória diferencial. A caracterização das membranas eletrólito envolveu medidas de grau de inchamento, capacidade de troca iônica e condutividade protônica. Foi possível observar que o PVDF confere boa resistência mecânica e aumento da estabilidade térmica das membranas. Membrana com 50% em peso de PVDF apresentou a maior condutividade protônica (1,89.10-3S.cm-1). Membranas de SPInd reforçadas com PVDF mostraram resultados promissores para uso como eletrólito em células a combustível.

Aug 17, 2017

By W. B. Evans, D. P. Taylor

"ANFO has two major disadvantages as an explosive low density and no water resistance. ANFO can be blended with more dense, water-resistant explosives to form ""Heavy ANFO"". The use of emulsion or slurry explosives as a matrix is an attempt to correct deficiencies on the basic ANFO while maintaining cost effectiveness.This paper will deal with four main topics.1. Product description, general properties, strengths and weaknesses.2. Technology of ""Heavy ANFO"" , the emulsion matrix concept and the range of products.3. Relative performance and economics in various rock types.4: Current status in Canada and worldwide, and the expectations for future use.IntroductionANFO has been in use for roughly three decades and remains the explosive of choice where conditions are suitable. ANFO has not become the universal explosive - despite its undoubted superiority in cost effectiveness - because it has serious flaws as an explosive. The most serious of these flaws are the low density and absence of water resistance in ANFO. Low density implies a low concentration of explosive energy in a borehole. The amount of energy available can be increased by. adding an energetic material, generally aluminum, or by drilling more holes. Both solutions add considerably to the over-all costs. The absence of water resistance in ANFO is inherent and can only be overcome by changing the fundamental nature of the product. The history of research in the explosives industry since the advent of ANFO is mainly the story of the various attempts to overcome one or both of ANFO's shortcomings.Many technologies and products have been developed to compete against ANFO, among them slurries, emulsion s and the so-called Dense ANFOs (ANFO with an extra nitroalkane liquid sensitizer). None of them was cost-competitive with ANFO so their market penetration has been limited to wet holes or specialized applications. The exception to this result is Heavy ANFO. The aim here was to have the best of both worlds, the high density and water resistance of emulsions or slurries plus the low cost of ANFO. The concept is very simple. ANFO is about 50 % air, roughly 30% in the prills and 700,10 between the prills . The air in the prills provides the necessary sensitivity but the air between them is waste volume. If one fills this volume with a high density, waterproof product, the resultant mix will be denser and more water resistant than ANFO and with very little added cost. This basic concept was invented by B. Clay in the 1970s and is covered by Canadian Patent No. 1 115 959. The water resistance and/or density of the mix can be tailored by changing the emulsion level. Because Heavy ANFO is relatively inexpensive while providing good in-hole densities and water resistance, it can compete successfully against all other bulk products. It competes against ANFO and Al / ANFO by allowing pattern expansion and reducing over-all costs while it competes against emulsions and slurries on price."

Jan 1, 1987

Aspects and anomalies in the present Standard Specifications for Blended Cements which may have operated in Australia against the development of the greater use of Slag Blended Cements are noted. Estimates of slag and ash usage in Australia are given and the need for further research with local materials stressed.

Jan 1, 1979

By G. Ward Wilson

Waste rock and tailings may be combined through intimate blending to create new materials with superior physical and hydraulic properties. The new material, termed Co-Mix, has high shear strength characteristics, low compressibility, low hydraulic conductivity, and a high water retaining capacity. Co-Mixed tailings and waste rock may be used to construct cover systems, internal barriers and seals, confinement structures and full depth waste repositories. Field scale test trials using Co-Mixed blends of waste rock, tailings and slag have been constructed at the Copper Cliff Mine in Sudbury, Canad. These lysimeters will be used to evaluate the performance of the new material for cover systems that may potentially be constructed on the tailings impoundment upon closure. In this sense, the paper point out the construction of the lysimeters with respect to expected field performance during the spring snow melt period and summer to produce cover systems for closure.

Sep 12, 2005

By C. Pace, D. Darlington, A. Montera, C. Lingren

"A phosphate beneficiation plant in Utah is using isotope-based Prompt Gamma Neutron Activation Analysis (PGNAA) technology to analyze the entire slurry streams of the incoming feed and final product in order to adjust the flotation circuits in near real time and optimize the plant output. The plant has gained greatly improved visibility/control and has reduced product variability for improved profitability and product quality. This paper takes a look at the economics as well as application details and the difference this technology provides in a phosphate application. SIMPLOT PHOSPHATES INTRODUCTION Simplot’s Vernal, Utah Phosphate Mine and Mill are located in the northeast corner of the state in the Uinta Mountains along US Highway 191, eleven miles north of the town of Vernal. The phosphoric acid and fertilizer plant fed by the Vernal mine is located 94 miles Northeast of Simplot Phosphates in Rock Springs, WY.At the Vernal plant, loader and shovel mining to 85 Ton capacity trucks is done at an annual rate of 3.8 Million tons of ore. Run of mine ore is crushed in a mineral sizer to minus 14 inch diameter at the rate 11,500 tons a day and transported to the SAG Mill’s 130,000 ton surge stockpile by overland belt. ORE RESERVES The ore is a Phosphoria Formation of sedimentary rock type dating to the Permian Age. The ore body rests over a 25 mile area on Weber Sandstone from the Pennsylvania and Permian geologic period. Layers of Phosphate Rock can vary in thickness from 0.3 up to 2.1 feet, alternating with layers of Mudstone. The eastern edge of the ore’s body Panel “G” runs 16 feet deep with a feed grade of 21.5% P205 with lower MgO diluents of less than 2.79%."

Jan 1, 2016

It is no longer satisfactory to assess the value of a coking coal on its intrinsic properties alone; its value depends upon its behaviour as a component in a blend. No single test can be used to make this assessment, it can only be made by carrying out a suite of tests. The quality parameters which are considered desirable, and which have widespread acceptance, have been discussed and their application to the blending of coals from New South Wales and New Zealand has been reported and discussed. Blending can be utilised to offset deficiencies, or capitalise on advantages, of the individual coals making up a blend. Coals can be blended, which alone are poorly, Coking, but which have compensating features. Blending also allows better exploitation of coking coal reserves. Several applications of blending have been reviewed with regard to coal producers and exporters, as well as coal users. The possibility of extracting a coking coal fraction from fuel coals is discussed. Blending systems and the coking of coal are also briefly reviewed.

Jan 1, 1971

It is no longer satisfactory to assess the value of a coking coal on its intrinsic properties alone, its value depends upon its behaviour as a component in a blend. No single test can be used to make this assessment, it can only be made by carrying out a suite of tests. The quality parameters which are considered desirable, and which have widespread acceptance, have been discussed and their application to the blending of coals from New South Wales and New Zealand has been reported and discussed. Blending can be utilised to offset deficiencies, or capitalise on advantages, of the individual coals making up a blend. Coals can be blended, which alone are poorly coking, but which have compensating features. Blending also allows better exploitation of coking coal Reserves..

Jan 1, 1980

By William J. Maloney

OVERVIEW Blind drilled shafts are becoming increasingly popular, particularly in the Appalachian coalfields, as a secondary and sometimes primary means of ventilation. The reasons for the rebirth of the blind shaft are mainly due to it's economics, timeliness, safety characteristics and inherent independence from underground operations. Historically blind drilling has been used to a limited degree in hard rock and tunneling ventilation. With the recent advances in cutters, bit design, equipment and lining systems, particularly in the Appalachian coalfields, blind drilled shafts are once again the shaft construction technique of choice to the educated ventilation specialist. [ ] HISTORY OF BLIND DRILLING Blind drilling has it's roots in numerous places, including the Nevada Test site, the coalfields of Appalachia and Germany along with the uranium mines of Arizona. Early technology was developed using a variety of equipment mainly of oilfield origin with oilfield drillers entering the industry on a project basis only to "pull in their horns" and return to the oil patch. Shafts completed by oilfield equipment range from the shallow 5' and 6' lined shafts on the Nevada test site to two (2) 10' lined, 730' deep shafts in Alberta for heavy oil development. Several of these shafts were completed to extraordinary depths with the record being a 90" diameter, 6,150' deep shaft being completed in the Aleutian Islands of Alaska in 1969. EQUIPMENT Oilfield equipment is still being used on the Nevada test site but elsewhere specialized blind hole equipment has been developed to enhance the efficiency of particular applications. Where steel liners are required the A-leg derrick with a simple hoist and rotary system is used. The largest user of this type equipment in the world is the former USSR where blind drilling for mine ventilation is the norm. On applications where trip time and cutter changeout are a priority, top drive hydraulic rigs have been developed which are highly automated, efficient and mobile. These rigs are particularly well suited for tunneling applications where shafts are shallow and sites are usually tight.

Jan 1, 1993

By Ray W. Amstutz

The shaft was drilled on US government land m the Piceance Creek basin and was funded by the US Bureau of Mines (USBM). It was drilled to 723 m to provide access to rich deposits of oil shale, nahcolite, and dawsonite for geotechnical test work and environmental mining research. Rotary drilling and dual-string, reverse-air, jet-assist circulation methods were used. Drilling required eight months. Site preparation, running, and cementing the casing required another four months. A 2.44-m ID steel welded casing, 508 mm thick was installed and 2.7 kt of cement were slurried and pumped into the annulus.

Jan 1, 1982

By R. W. Amstutz

Abstract. The shaft was drilled on U.S. Government land in the Piceance Creek Basin and was funded by the U.S. Bureau of Mines. It was drilled to 723 meters (2 371') to provide access to rich deposits of oil shale, nahcolite and dawsonite for geotechnical test work and environmental mining research. Rotary drilling and dual string, reverse-air, jet-assist circulation methods were used. Drilling required 8 months. Site preparation, running and cementing the casing required another 4 months. A 2.44-meter (96-inch) ID steel welded casing, 5.1 cm (2 inches) thick was installed and 2 700 tonnes (63 000 sacks) of cement were slurried and pumped into the annulus.

Jan 1, 1980

By William J. Maloney

Blind drilled shafts are becoming increasingly popular as a secondary and sometimes primary means of ventilation. This is particularly true in the Appalachian coalfields. Some reasons for the rebirth of blind shafts are economics, timeliness, safety characteristics and their inherent independence from underground operations. Blind drilling has had limited use in hard rock and tunneling ventilation. Advances in cutters, bit design, equipment and lining systems have made blind drilled shafts the shaft construction technique of choice for ventilation specialists. History of blind drilling Blind drilling's roots include the Nevada test site, the coalfields of Appalachia and Germany, and the uranium mines of Arizona. Early technology was developed using a variety of equipment mainly of oilfield origin. Shafts completed by oilfield equipment ranged from the shallow 1.5 and 1.8 m (5 and 6 ft) lined shafts on the Nevada test site to two 3 m (10 ft) lined, 222 m (730 ft) deep shafts in Alberta for heavy oil development. Several of these shafts were completed to extraordinary depths. The record, completed in 1969, is a 2.28-m-diam (90-in.-diam), 1875-m (6150-ft) deep shaft, located in the Aleutian Islands of Alaska.

Jan 1, 1993

By James H. Cobbs

Blind boring of shafts is becoming an increasingly important part of shaft sinking. Blind-bored shafts have reached diameters of 25 It in Europe and 16-1/2 ft in the United States. Much of the technology developed for blind boring has evolved from the technology of drilling wells for oil and gas production. Blind boring offers economic advantage in a number of situations where conventional shaft sinking either is extremely difficult or very expensive by virtue of large-capacity aquifers which must be penetrated, unstable ground or where very rapid sinking is required. In sedimentary rocks, blind boring is cost competitive with conventional sinking, in diameters of about 12 ft or less. Blind boring is not competitive with raise boring where conditions are favourable for raise boring. Blind boring does, however, offer greater flexibility than raise boring and can be performed in situations where raise boring is inefficient or impossible. Combination machinery has been developed to perform both blind boring and raise boring, so that the machine can be used effectively in situations where only the near-surface portions of the shaft are unfavourable for raise boring. Development work is being supported by the United States Bureau of Mines for blind boring equipment capable of boring shafts up to 30 feet in diameter.

Jan 1, 1979

By Justus Deen, Paul V. Sterk

Through the 119 year history of the Homestake Mine various methods of raise mining have been used, these include conventional, bored, and drop raises. These raises provide passage for men and supplies, provide ventilation, transfer broken rock from level to level, and serve as emergency escapeways. As the 1980’s came to a close, many of the larger ore bodies in the mine had been mined out. This has resulted in many crown pillar situations that required a method to mine them. In addition, the Homestake ore body also contains numerous ore reserves that have short vertical height. The ore itself can be from vertical to 50 degrees in dip. Due to the high cost of drift and ramp development many of these ore bodies are subeconomic using conventional mechanized cut and fill mining.

Jan 1, 1996

By Justus Deen, Paul V. Sterk

Through the 119 year history of the Homestake Mine various methods of raise mining have been used, these include conventional, bored, and drop raises. These raises provide passage for men and supplies, provide ventilation, transfer broken rock from level to level, and serve as emergency escapeways. As the 1980s came to a close, many of the larger ore bodies in the mine had been mined out. This has resulted in many crown pillar situations that required a method to mine them. In addition, the Homestake ore body also contains numerous ore reserves that have short vertical height. The ore itself can be from vertical to 50 degrees in dip. Due to the high cost of drift and ramp development many of these ore bodies are sub-economic using conventional mechanized cut and fill mining.

Jan 1, 1996

By James E. Friant

The technology applied to shaft sinking has lagged far behind other construction activities. While surface oriented construction and mining have made great strides with new processes and equipment, the majority of shafts sunk currently still follow a drill, blast and muck-out cycle developed in the 16th century. Today, in 1979, the shaft sinking industry is in the midst of its own private industrial revolution. Millions of dollars are being spent annually by industry and government alike to spring the art of shaft sinking into the 20th century. The objective of this paper is to review a few of the newest mechanized schemes for shaft sinking. This is not a theoretical review, however, but a practical one, and deals only with hardware and projects which are currently on jobsites. Figure 1 shows the equipment. On the left is the 241SB 184, a 24 foot diameter blind shaft borer. This machine is currently at about 200 feet, constructing a coal mine shaft in Alabama. It is built and utilized in a manner similar to a tunnel borer. In the upper center is the 1211SR, a 12 foot diameter blind shaft reamer. This machine follows a 6 foot pre-drilled blind pilot hole, and is at work in Chicago. On the upper right is the 121BR, a powerful new blind drill. Just below it is the conical drill head for the 121BR which can utilize either carbide or standard disc cutters. At the center bottom is an expandable back reaming head which can be used to enlarge a drilled shaft up to a maximum of 16 feet diameter, or can be used to produce a shaft having several diameter changes. This equipment is also in use in Chicago.

Jan 1, 1979