Search Documents

By Derek T. Novotny

Blasting cap precision is of major importance to advanced blast design. New technologies have introduced the use of microchips within detonator casings in the hope that the electronic control of the timing element will increase the accuracy of the cap and therefore improve the results of perimeter control blasting applications. The electronic detonators have proven to be accurate in timing tests done to date. They boast cap scatter results to microsecond accuracy, but the question is, does this degree of accuracy actually prove to be beneficial during practical use in the industry, or are conventional technologies applicable.

Jan 1, 1998

By L Neems

In conjunction with Orica Explosives, Worsley Alumina have managed a program of continuous improvement to their cap rock blasting over the last two years. Blasting conditions are challenging because of the hard and shallow nature of the material. Blasting costs must be controlled and the environmental consideration of noise and dust is critical. Worsley have sought to determine the optimum balance between drilling and blasting costs and fragmentation. As the cap rock has few inherent weaknesses, loader productivity is strongly controlled by the degree of fragmentation from blasting. The optimum blasting solution is also constrained by maintaining airblast levels at the surrounding residences below 115 dBL . The major blast design parameters optimised during the program were stemming type, stemming length, powder factor and blasthole diameter. A series of carefully managed trial blasts were fired during 1997 and 1998 to quantify the effect of these parameters. Fragmentation was digitally measured using OricaÆs Powerseive G technique. Shovel productivity, airblast levels and blasting costs were also quantified. As a result of the project, Worsley now have an increased knowledge of the key parameters driving blast performance, and their consequent impact on downstream processes, the environment and total mining cost.

Jan 1, 1999

By Jack Eloranta

To improve control of blasting, tests were performed to assess non-electric cap accuracy. Simultaneous testing using a Velocity of Detonation Recorder (VODR), Red Lake LoCam and an Instantel DS-677 blast monitor was done. Favorable comparisons were found in the three records. This testing confirmed the accuracy of an inexpensive and expedient cap testing procedure.

Jan 1, 1992

By K. Tajrych

Time and again, lives are lost in underground cave-ins only be- cause there is no quick, sure way of locating the victims. When such accidents happen, rescuers must usually depend on the testimony of eye- witnesses for information on the whereabouts of trapped miners. Seldom is this information reliable. The witnesses themselves have just been through a traumatic experience that has distorted or destroyed their sense of time and place. A far more reliable method of finding men underground has recently been developed by the Coal Mining Research Institute of Ostrava, Czechoslovakia. With this system, a miner can be located with adequate precision even if he shows no sign of life. For the system to work, the miner need only have his electric cap lamp somewhere nearby. The system consists of a minute radio transmitter operated by the lamp battery (Fig. 1). This tiny transmitter continuously emits high- frequency electromagnetic waves that can be picked up by a sensitive direction-finder receiver in case of accident.

Jan 8, 1969

By Koji Matsubara, Yoshiaki Iguchi, Shoji Hayashi

Iron ore particles of a limonite iron ore were reduced completely with H2 at 1023K to 1273K in a fluidized bed. Then, at 973K, the formed iron was exposed to HrH2S mixtures (sulfur activity, as=0.5) for 3.6ks and carbidized with CO-H2-H2S· mixtures at 0.1 MPa. During the carbidization, the particles of about 150mg were sampled at every 600s interval. The sampled particles were analyzed by XRD and chemical analysis for C and S to evaluate the content of Fe3C, Fe5C2, Fe and free carbon. The reaction extent is defined as fo=Xfc3C +xFc5c2; x is the molar fraction of Fe in Fe3C. The carbidization curves can be fitted very well to -ln(l-f0)=g(pb T)t; g(p; T) is the carbidization rate, i.e. the carburization rate on the pore surface of reduced iron. The rate is found to be nearly proportional to the specific surface area of reduced iron, a P 0 , which decreases with increasing the reduction temperature. The value of a P 0 does not change by the carbidization and the stability of the iron carbide product in the atmosphere increases with the temperature.

Jan 1, 2000

By Emiliano Mauro Giraldo Paredez

El presente estudio señala la capacidad de anclaje de los pernos de roca más utilizados en el Perú y la relación existente con la longitud. Originalmente, las pruebas en bloques de granito se debieron realizar dentro del campus de la UNMSM, pero por no reflejar las condiciones reales, se ejecutó en la mina Reliquias de la Cía. Minera Castrovirreyna (Huancavelica). Los perons estudiados son Splet, Barras Helicoidales, Hydrabolt y Swellex, convenientemente acondicionados para tener anclajes efectivos de 1, 2, 3 y 4 pies, donde los resultados demuestran que la capacidad de anclaje de los pernos no guarda una relación lineal con sus longitudes, es decir, al duplicar la longitud de un perno, su capacidad de anclaje no necesariamente será el doble. Asimismo, La elongación de los pernos, tiende a guardar una relación lineal con la carga aplicada, mientras que el comportamiento de las Barras Helicoidales es irregular, sobre todo cuando se instalan con cemento.

Sep 12, 2011

By Mauro Giraldo Paredez

"El presente texto determina la capacidad de carga de las toneladas que puede soportar cada pie de anclaje de los distintos pernos, así como el comportamiento de sostenimiento de perno al variar su significado. En el caso de los Split Set y barras helicoidales,se solicitó a los proveedores que los cortaran en longitudes apropiadas para que, al instalarlos, hagan los anclajes efectivos antes indicados. En el caso de los Swellex e Hydrabolt, que son pernos de expansión, se tuvo que acondicionarlos utilizando tubos de estrangulamiento y otros materiales."

Jun 1, 2012

By Ana Carolina dos Reis Lima

Este artigo tem o objetivo de apresentar a capacidade de remoção de íons Pb2+ de um argilomineral oriundo da região sudoeste do Pará. A caracterização do argilomineral foi feita através das técnicas de Difração de Raios-X (DRX) e Microscopia Eletrônica de Varredura (MEV). A metodologia utilizada foi a do sistema de banho finito para determinação da percentagem de remoção (%Rem) do argilomineral. Foram utilizadas três concentrações sintéticas de chumbo (10, 30 e 50ppm) com diferentes pH (3, 4 e 5) para avaliação da absorção de íons pelo argilomineral. Ainda, este argilomineral foi revestido com quitosana com previsão de aumentar a adsorção dos íons Pb2+. Os resultados mostraram o potencial de adsorção acima de 95% para todas as concentrações em pH 5; e a adição de quitosana aumentou esse potencial para acima de 99%. Em pH 4, a, a quitosana proporcionou aumento na percentagem de remoção na concentração de 10ppm. Isso implica em uma potencial aplicação para remoção de metais pesados em efluentes da região sudoeste do Pará em vista da extração de minério presente nesta região.

Oct 30, 2017

By Jeannine Wendy Salas Huamán

Dado que la empresa minera tiene como objetivo el fortalecimiento de la responsabilidad social y ambiental para la AID (Puno), se implementa un programa de actividades que responda a la responsabilidad social y ambiental. En ese sentido, el presente texto describe la capacitación como una herramienta de una logística -en tanto se entrene a los pobladores de la AID para que puedan brindar servicios a la minera, se concilie la explotación minera con la población mediante la logística y se establezca una alianza con los pobladores formándolos como proveedores, de forma que se obtenga una ganancia conjunta.

Nov 1, 2013

By Carolina Sartori Marzullo

Apresenta-se a metodologia e sistemática para gestão da capacitação como ferramenta para aumento da competitividade e ganho de resultados do negócio num contexto crítico para o segmento.

Aug 16, 2017

By S. R. S. Sastri

By using the data of E.A. Hersam and F.C. Bond's equation for energy consumption in comminution, a method was developed to analyze the performance of industrial jaw crushers. The study showed that industrial jaw crushers are generally operated below capacity. The study also showed that industrial jaw crushers generally have sufficient installed power to operate at, full capacity. The method presented can be used to estimate the capacities and power requirements of jaw crushers.

Jan 1, 1995

By T. Kerr, C. Mattich, J. Wilson

"In refractory gold concentrates, gold is occluded in sulphide minerals preventing efficient cyanide leaching. Hence, roasting is used to oxidize sulphur and organic carbon, the latter being necessary to minimize recovery loss through the preg-robbing effect. In 2009, Outotec commissioned the circulating fluidized bed roaster at Syama gold mine in Mali. Since 2013 Resolute and Outotec have been implementing improvements to the roaster performance with the capacity increasing from 8000 t/month in 2013 to above 13,000 t/month in 2016, while achieving a residual sulphide sulphur and organic carbon contents of below 0.1 wt.% and 0.4 wt.%, respectively. Thus a gold recovery in the CIL of above 90% is attained. In 2016, Outotec audited the Syama roaster. The analysis resulted in the Low Carbon Roaster (LCR) upgrade concept which (i) allows re-processing of calcine dust from the spray cooler and ESP after pelletization and (ii) allows the roasting of a further fine-organic carbon rich feed, i.e. de-slime circuit tailings. The LCR upgrade aims to reduce organic carbon to <0.2 wt.% and increase roaster-leaching gold recovery by >3%. Project development included extensive testwork. The LCR process is expected to become operational during FY 2019.INTRODUCTION Double refractory sulphide ores exhibit the characteristics of gold locked within pyrite grains, in the presence of preg-robbing natural (organic) carbon. Hence, to achieve high recovery during subsequent processing steps, i.e. cyanide leaching, oxidation of sulphide sulphur is required, producing a porous calcine by way of a roasting step. This allows for the gold contained within the pyrite grains to be accessible during cyanide leaching. Furthermore, it is necessary to oxidize the organic carbon. Oxidizing the organic carbon is essential as gold recovery loss occurs as a result of gold-cyanide complexes being adsorbed on organic carbon, this phenomenon is termed as preg-robbing (Miller et al., 2016). The gold absorbed on the organic carbon is lost, reporting to the tailings stream. Hence, the aforementioned oxidation of sulphide sulphur and organic carbon is the process goal. Nonetheless, the latter must occur at a controlled temperature which is concentrate/ ore specific, since the pores of the produced calcine should not sinter, as this makes the gold contained in the calcine less accessible during leaching, leading to gold recovery loss. The tight temperature control requirement is a decisive factor in the choice of a Circulating Fluidized Bed (CFB) as the roasting reactor, due to the excellent mixing characteristics of the CFB which results in temperature homogeneity of (+/-10°C). Roasting of double refractory ores, as described above, can be included in the flowsheet after comminution and grinding, a process termed as whole ore roasting, or by including a flotation circuit termed as concentrate roasting. Roasting the flotation concentrate results in less solid flow, increased sulphide sulphur grade and organic carbon content resulting in a higher heating value and higher gold content. A typical composition of the Syama ore and concentrate is given in Table 1. Ore average values presented correspond to the period 2015, while concentrate values are typical for the flotation performance throughout the period 2012–2015."

Jan 1, 2017

By T. Krumins, F. C. Ruff, M. Eichhorn, L. Zunti

Hatch Ltd. has recently completed a project to increase refractory gold ore processing capacity at Newmont Mining Corporation’s Twin Creeks facility. The objective of the project was to increase throughput by approximately 10% by adding a third autoclave feed pump to each of the two autoclave circuits. To minimize project capital cost, autoclave feed pumps from Newmont’s decommissioned Lone Tree facility were evaluated and found to be suitable for this new service. The existing pressure oxidation circuit was reviewed in a debottlenecking study to determine other upgrades required to facilitate the increased throughput. Interruption to operations was minimized with a detailed construction plan, supplemented with detailed 3D layout model sequencing studies. The focus of this paper is project development, multi-discipline design considerations, and implementation results.

Jan 1, 2014

By N Steenkamp, L Furstenberg, W Cele, M Richter

Managing productivity and improving efficiency for a healthy return on capital employed have become key mining industry strategies under prevailing tough global market conditions. However, achieving this in a multisystem environment such as a mining operation can be daunting. The field of discrete event simulation offers some relief, giving engineering teams insight into multivariable systems and stochastic processes. It allows for integrated system thinking and domain expertise to be woven into project thinking fibre. Directed system optimisation and therefore improved efficiency becomes possible. Furthermore, capital discipline accrues from optimal upgrade investments. This paper illustrates the practical application of this approach by reviewing a typical case study for a direct shipping iron ore operation. Dynamic simulation was used to establish maximum processing plant capacity under varying material characteristics and identify capital-efficient upgrades for increasing production.The study started with descriptive statistical analysis of existing data. Discrete equipment and system capacities were defined, followed by static plant mass balance calculations to establish bottlenecks and overall static capacity. Equipment ‘uptime’ and ‘downtime’ analyses established system and overall plant availability and utilisation. From this information, a dynamic simulation model could then be developed and initially calibrated against actual plant performance to verify its robustness. Once confirmed to accurately represent existing plant dynamics, system capacity response to variable changes could be tested to ultimately determine maximum plant capacity. Additionally, plant optimisation was incorporated to arrive at optimal upgrade points. Maximum capacity and necessary upgrades were established as a function primarily of feed size distribution. Additionally, the interfacing effects of rehandling feed material to the final product grade and potentially to life-of-mine were established as important outcomes. The results of the study illustrate the value of using dynamic simulation models to realistically and cost-effectively increase throughput.CITATION:Cele, W, Furstenberg, L, Richter, M and Steenkamp, N, 2015. Capacity evaluation of iron ore processing facilities utilising dynamic simulations, in Proceedings Iron Ore 2015, pp 597–604 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A. J. S. Benade, A. J. A. Heyns, N. B. Strydom

The maximum oxygen intakes of samples of about 30 Bantu, weighing less than 50 kg from different tribal groups (Zulu, Xhosa, Sotho and Shangaan) were measured on a treadmill. The mean maximum oxygen intake of the 164 men was 2,12 litresjmin and only 18 men (11 per cent of the sample) had maximum oxygen intakes of 2,5 litres/min or above (the minimum requirement for such tasks as shovelling rocks and tramming it). The samples of the different tribes differ in age, but when the age effect is taken into account then there were no significant differences between tribes in maximum oxygen intakes. An incidental finding was that both age and body weight correlated significantly with the maximum oxygen intakes of these underweight subjects. Not one of the subjects who weighed less than 45 kg or who was older than 40 years had maximum oxygen intakes high enough to permit their being able to do strenuous work underground. It is clear therefore that Bantu who weigh less than 45 kg or are older than 40 years should not be employed on such strenuous tasks as shovelling rock and tramming it.

By Marian Radetzki

The economic developments and industrial behavior patterns that led to a lasting excess capacity in the world non-ferrous metals industries from the aid-1970s are explored. Detailed attention is devoted to analyzing and defining crucial concepts like "capacity", "excess capacity", "capacity maintenance" and "investments". Empirical evidence of capacity utilization and capacity growth in the industries under study is provided. The coincidence of excess capacity and low prices on the one hand, and investments in capacity maintenance and capacity expansion, on the other, is seen as a consequence of substantial declines in the metal industries&apos; investment and production costs during the period studied.

Jan 1, 1989

By Stig Premfors

Lamco Joint Venture is operating a Dravo Pelletizing machine to produce pellets from the natural slimes of an earthy hematite ore. The grate area of the machine 3.3 x 106 m equal to 350 m2 (3800 sq. ft.) and the installed fan capacity is 8200 HP. The limiting factor for production is normally fan capacity. This means that the processing fans can not pull the additional air (i.e the additional calories or BTUs) through the bed which would be required for increased production. A way to increase production without major modifications is to supply the additional calories needed for increase production by adding coal to the pellet feed. After successful laboratory tests following method of coal addition has been chosen and the following results have been obtained. 1. The ground coal is added to the slurry prior to the filters and the rotary dryer. 2. By adding 0.6% coal, an increase of about 15% in production rate has been obtained. 3. No significant changes of metallurgical properties have been observed (i.e. tumbler index, compressive strength, ferrous iron content, reducibility, Linder degradation and swelling). 4. No unexpected operation problems have been experienced. The pellet discharge temperature increases and is the limit for how much production can be increased by coal addition without making plant modifications.

Jan 1, 1971

Mining of copper ore is still the most important business in Chile. In order to mine ore with a copper content of less than one percent at Minera Los Pelambres in an economical way, opencast mining is mandatory. Due to the prevalence of avalanches at the mine, the concentrator was located in a stable area, some distance from the mine. As a consequence, the material has to be transported between mine and concentrator by conveyor. A downhill conveyor system has been implemented for more than ten years as the most suitable and most economical ore transport alternative. Due to the length (12.6 km) and inclination (1300 m drop) of the conveyor system, the stresses in the steel cord belt are the dominant design criterion, resulting in a belt quality of ST 7800. Additional dynamic belt stresses during transient operating conditions are avoided by the installation of high capacity adjustable frequency drives. The rating of a single drive unit is 2500 kW. During ten years of operation, several capacity increases have been implemented, from an initial 5800 t/h up to the current capacity of 9900 t/h. This presentation describes the engineering challenges of the implementation of the world&apos;s strongest belt conveyor system. Capacity increase measures like the development of new control and breaking strategy, proved by dynamic simulation of belt forces and belt speed scenarios are explained. During this long-term partnership of RWE Power International, the former Rheinbraun Engineering, with Minera Los Pelambres, RWE has been engaged continuously for development work, safety checks, expert opinions and maintenance audits, and giving new impulse to conveyor technology.

May 1, 2010

By S. Sarioglan

The bleaching of edible oils, industrial oils, and some chemicals may be achieved using natural and acid-activated clays. These materials remove impurities and pigments from the oils. In this work, a bentonite clay from Turkey (Somas bentonite) was activated with different concentration of H2SO4 and HCl at 70~90°C and 5~8 hours. Under these conditions several cations were removed from natural bentonite (Al, Mg, and Fe) and DTA-TGA, FT-IR curves of the solids obtained after acid treatment were examined. Treatment time and acid concentration increased the degree of destruction of the bentonite structure which was determined by ICP. Activated samples were tested in order to verify their capacity to bleach soybean oil and compared to standard commercial bleaching clays. The experimental results indicate that treated samples with H2SO4 have the same efficient in bleaching crude soybean oil with the standards and treated sample with HCl is more efficient in bleaching than the commercial products.

Jan 1, 2014

By Mohab Sabry

Pile foundations are used extensively around the world to support both inland and offshore structures, including important structures such as nuclear plants and oil drilling platforms. The limit of the pile depth is currently predicted during the pile deriving process, given no chance for the designer to predict accurately the capacity of these piles prior installation. Furthermore, after pile installation, designer may not be able to modify the pile group design by increasing the number of piles and or changing the geometry of the pile group. This paper presents a numerical model for the case of single piles driven in homogenous sand using finite element technique and the theory of cavity expansion. The model is capable of simulating all the construction stages of concrete piles up to the maximum depth, which can be driven in sand and accordingly the capacity, which can be attained by these piles. The program "PLAXIS" is used to perform the proposed analysis. This model simulates the process of pile driving in terms of the changes in the earth pressure and the overconsolidation ratio acting along the pile&apos;s shaft. Based on the results of the present investigation, these depths can be predicted based on the pile geometry and the sand properties. Charts are given to provide these depths for given pile/soil conditions.

Jan 1, 2006