Search Documents

By Jie Li

Series of carbon compounds as anode materials were prepared for super lithium ion capacitor using graphite and active carbon (AC) as raw materials. Their electrochemical properties were investigated by constant current charge-discharge test. The results showed that the compound anode had good capacitive performance as well as Li-ion battery performance. The potential of the capacitor could be as high as 3.5V vs Li/Li+ when compared with 2.5V vs Li/Li+ in the AC-AC capacitor, accordingly, the energy density increased from 21.7Wh/kg to 40.3Wh/kg. The compound anode also had excellent rate performance that as the current density increasing from 0.1A/g to 1A/g,the capacitance decreased only 1.3F/g, and good cycle performance that the capacitance holding remained 96.7% after 10 times cycles even at the highest potential of 3.5 V vs Li/Li+.

Jan 1, 2009

The control of carbon concentration in a counter current carbon absorption circuit is critical to optimise gold recovery. MINTEK has developed a carbon movement controller to address this potentially problematic area in gold extraction. This controller reduces operator interaction by automating carbon movement. Elution schedules are entered into the control system, which then moves the carbon through the circuit into the first adsorption tank until enough carbon is available for elution. This is done while maintaining the specified carbon profile within the circuit. MINTEK has also developed an online-carbonconcentration- meter to measure carbon concentration in pulp. The meter uses an ultrasonic measurement technique. Long term testing has shown the measurement to be robust and require minimal maintenance. Results from a gold mine in South Africa’s well known Witwatersrand gold producing area has shown a decrease in soluble gold loss between 30 - 50% when the controller was used.

Jan 1, 2014

By David Seymour

Precious metal producing mining companies in the United States, Canada, and South Africa were surveyed on carbon usage practices in the recovery of silver and gold. Responding companies represented CIP/CIL dperations, heap leach operations and combined mill/leach operations. Operational practices and carbon consumption rate measurements are presented, correlating consumption rates with process attributes. Precious metal producing mining companies in the United States, Canada, and South Africa were surveyed on carbon usage practices in the recovery of silver and gold. Responding companies represented CIP/CIL dperations, heap leach operations and combined mill/leach operations. Operational practices and carbon consumption rate measurements are presented, correlating consumption rates with process attributes.

Jan 1, 1992

By D. Thibault, A. Akhiate, M. Brochu, E. Braud

Cast martensitic stainless steels, 13%Cr-4%Ni, having carbon contents between 0.018 wt% and 0.067 wt% were normalized, air quenched, and tempered at two different temperatures (550°C and 610°C). Their microstructures were characterized by optical microscopy and X-ray diffraction (XRD). Macro and microhardness, tensile strengths, and impact resistance were quantified for each material and condition. Results show that the prior-austenite grain size is constant through the materials but the percentage of reformed austenite, contained in the martensitic matrix, depends strongly on the material chemistry and on the tempering temperature and on its duration. It is observed that, independently of tempering conditions, an increase in carbon content increases the material hardness and tensile strengths, whereas the elongation remains constant. In contrast, the results of Charpy type impact toughness tests show a different trend. The material containing the average carbon content (0.034 wt%) is significantly tougher than the two other alloys. Surprisingly, the toughness of the steel containing 0.034 wt% carbon was found independent of the reformed austenite content. It is thus concluded that carbon and reformed austenite contents are not the only parameters affecting the toughness of these steels.

Jan 1, 2014

By Steven G. Jansto

Carbon content and continuous casting parameters affecting solidification behavior, such as super heat, mold level fluctuation, heat transfer, fine grain chill zone depth and other process solidification parameters directly influence the surface and internal quality of the steel strand. The carbon content, resultant fine grain chill zone depth, the equiaxed-columnar transition zone and the strain energy are the primary drivers that govern hot ductility behavior. These factors influence the propensity for crack formation during the unbending section in the continuous casting process. Elements such as microalloys exhibit secondary or tertiary root causes for crack formation and are not the primary crack formation root cause. This solidification research identifies that the traditional hot ductility as measured via the percent reduction in area (%RA) at elevated temperature grossly overstates the minimum ductility required to assure crack-free casting of microalloyed steels. The strain at the ultimate tensile strength exhibits a very high correlation coefficient with strain energy while an extremely low correlation coefficient is exhibited with %RA.

Oct 30, 2017

By D. J. Young

Alloys used at high temperature must resist both creep and corrosion. Design for corrosion resistance is based on the formation of a slow-growing, protective oxide scale by selective oxidation of an appropriate alloy component, usually chromium or aluminium. A successful scale will exclude other corrodents, notably carbon, which can otherwise cause extremely rapid corrosion at high temperatures. Selective oxidation of an alloy component necessarily lowers the concentration of that metal in the alloy subsurface region. Under thermal cycling conditions, mechanical damage to the scale leads to renewed oxide growth and accelerated alloy depletion. Eventually, a point is reached where diffusion of a corrodent into the alloy becomes competitive with the outward diffusion of alloy metal to repair the protective scale. Two examples of alloy failure by carbon attack are considered. In the steam cracking (pyrolysis) process, centrifugally cast tubes of heat-resisting alloy are exposed to a gas stream of hydrocarbon and steam, at a carbon activity of unity. Formation and repair of the surface chromia scale causes alloy depletion, Kirkendall void formation, and subsequent internal precipitation of chromium-rich carbides. Their formation makes chromia scale formation much more difficult, and generates internal stress. Eventually, the tubes fail by creep rupture. In other processes (e.g. steam reforming, heat treatment), synthesis gases are supersaturated with carbon at intermediate temperatures. Once the alloy's protective scale is breached, carbon attacks the depleted substrate. In the case of ferritic alloys, it forms a surface scale of Fe3C. As this scale thickens, the supersaturated carbon precipitates as graphite within its outer regions. The resulting volume expansion causes disintegration of the cementite in a process known as metal dusting. In the case of austenitic alloys, no metal carbide is formed. Instead, carbon dissolves in the depleted metal to diffuse inward and precipitate as graphite within the metal matrix. Again, volume expansion causes disintegration of the alloy, and metal dusting results. Dusting occurs at an extraordinarily rapid rate, and leads to failure by section loss or even penetration.

Jan 1, 2013

By Costello MC

An alternative process for desorbing and recovering metals from activated carbon has been developed, and is the subject of several patent applications by Micron Research (W.A.) The system uses the principle of conditioning the carbon in a strong alkaline cyanide solution followed by distillation desorption in a fractionating column, using the carbon as the column packing and methanol as the desorbing agent. The system offers the following advantages : (a) The processes of desorption, methanol recovery and reactivation are all carried out in a single column with the carbon itself acting as the column packing. No other desorption plant items or fractional distillation equipment are required. (b) The metal values are concentrated into the water content of the carbon and no other water is used except as condenser coolant. This produces very high grade gold silver solutions which give high current efficiencies in the electrowinning step. These high gold concentrations allow almost complete separation of gold and silver from copper in the electrolytic cell. (c) The process is completed to a tailing assay of less than 200g Au/tonne carbon in 15 - 20 hours allowing turn around of carbon batches on a daily Basis.

Jan 1, 1982

By J. Charles Miller

NATURAL carbon dioxide has recently been exploited in the United States in consequence of oil and gas developments in the Western States and the growing demand by transcontinental and transoceanic shippers for solid carbon dioxide. The discovery by drilling of commercial deposits resulted in consideration of its geographic and geologic distribution and occurrence. Its wide distribution in nature is evidenced by its occurrence in the atmosphere, hydrosphere and lithosphere. The question of origin of carbon dioxide involves consideration of theories similar to those concerning natural hydrocarbons, although available evidence favors an inor-ganic rather than an organic source. Areas favorable to development of commercial production appear to be those in proximity to igneous rocks or in the vicinity of decadent volcanic activity, where, it has long been known, the gas is evolved either free or dissolved in the waters of furnaroles, geysers or mud pots. Structure contour maps are presented showing the Wagon Mound anticline in New Mexico and the Farnham anticline, Utah. A well drilled on the latter supplies gas to a 20-ton plant manufacturing solid carbon dioxide at Wellington, Utah, on the Denver and Rio Grande R.R., whence it is shipped to surrounding territory and to the West Coast. Before funds are invested in a plant for the manufacture of liquid or solid carbon dioxide, whether supplied by wells or springs, an effort to ascertain the volume of gas available is advisable. The use of present methods of estimation of gas reserves with modifications to account for the quantity absorbed by any water present in the produc-ing formation is recommended. The Farnham anticline is used as an example and computations are made of the probable volume of gas originally present in the struc-ture. No attempt was made to compute reserves in the Niland area, California, for the reason that in such areas it is believed the volume is indeterminate.

Jan 1, 1937

By J. Charles Miller

NATURAL carbon dioxide has recently been exploited in the United States in consequence of oil and gas developments in the Western States and the growing demand by transcontinental and transoceanic shippers for solid carbon dioxide. The discovery by drilling of commercial deposits resulted in consideration of its geographic and geologic distribution and occurrence. Its wide distribution in nature is evidenced by its occurrence in the atmosphere, hydrosphere and lithosphere. The question of origin of carbon dioxide involves consideration of theories similar to those concerning natural hydrocarbons, although available evidence favors an inorganic rather than an organic source. Areas favorable to development of commercial production appear to be those in proximity to igneous rocks or in the vicinity of decadent volcanic activity, where, it has long been known, the gas is evolved either free or dissolved in the waters of fumaroles, geysers or mud pots. Structure contour maps are presented showing the Wagon Mound anticline in New Mexico and the Farnham anticline, Utah. A well drilled on the latter supplies gas to a 20-ton plant manufacturing solid carbon dioxide at Wellington, Utah, on the Denver and Rio Grande R.R., whence it is shipped to surrounding territory and to the West Coast. Before funds are invested in a plant for the manufacture of liquid or solid carbon dioxide, whether supplied by wells or springs, an effort to ascertain the volume of gas available is advisable. The use of present methods of estimation of gas reserves with modifications to account for the quantity absorbed by any water present in the producing formation is recommended, The Farnham anticline is used as an example and cornputationa are made of the probable volume of gas originally present in the structure. No attempt was made to compute reserves in the Niland area, California, for the reason that in such areas it is believed the volume is indeterminate. INTRODUCTION Carbon dioxide, in liquid and solid form, has found a wide variety of uses other than its primary application in carbonating beverages. It is now used in more than 40 different ways, ranging from cooling or freezing to use in gas or liquid form for mechanical purposes, chemical industry, explosive, fire extinction, and tire manufacturing. Undoubtedly the chief supply of carbon dioxide is obtained from industrial plants or artificial sources and until recently natural deposits of the gas have received little consideration. Few will question the utility and perhaps dependability of artificial sources, which possess the advantage over

Jan 1, 1937

By Evans E. C.

At first sight, the extinction of a mine fire by the action of some such gas as carbon dioxide would appear to be quite a simple and practicable operation. From a consideration of the theoretical aspects only of the question, it becomes evident that the matter is not so simple as it appears to be at first sight. The fire at the Senghenydd Colliery occurred as the result of the disastrous explosion of October 14th, 1913. This explosion was confined to the west side of the colliery; and as a result the timbers in the main intake on this side were set on fire; but these were soon buried beneath falls, and the tire continued under them. Attempts were made to extinguish it with water, with the aid of chemical extinguishers, and by digging it out; hut these had to he abandoned, and ultimately the fire-zone was sealed off by “ bashings” (stoppings). By December, progress in the decrease of combustion was so slow that it was decided to try the effect of inert gas. The installation, control and operation of the carbon dioxide plant and associated water-gauge are described in detail and conclusions drawn for the extinguishing of mine fires by CO2

Dec 1, 1916

By S. K. Kawatra, S. K. Valluri, S. J. Root

Carbon dioxide, a by-product of combustion reactions, is a greenhouse gas linked to climate change. At Michigan Technological University, we have studied the capture of CO2 using alkali scrubbing solutions in a pilot scale packed bed counter-current scrubbing column. To do this, we have simulated flue gas by combining streams of CO2 and compressed air. Real flue gas has impurities such as CO, SO2, and NOx, and has lower levels of O2 than our simulated flue gas. In order to study CO2 capture from a real flue gas, the Department of Chemical Engineering worked with the Facilities department to install a pilot scale scrubbing column in the Michigan Tech steam plant. Experiments were conducted using a sample stream of the flue gas from the boiler in the steam plant. Data collected from these experiments were compared to the data collected from identical experiments conducted on simulated flue gas in the lab. The capture efficiency of the real flue gas scrubbing column is discussed in this paper. BACKGROUND The most common equipment used to separate CO2 from a flue gas stream is a counter-current packed-bed scrubbing column. The department of Chemical Engineering at Michigan Technological University has two such pilot scale columns. In order to study the effect of impurities found in real flue gas, one is installed in a controlled laboratory using a simulated flue gas created by mixing CO2 and compressed air. This column will be used to establish a baseline for percent capture analysis and is displayed by figure 1. The second scrubbing column is identical to the first, and is installed in the Michigan Tech central energy plant. The plant produces up to 130,000 lb/hr of 80 psig steam to provide hot water and heat for campus buildings. A typical wintertime load burns around 25,000 SCFH of natural gas; this load releases 1.4 metric tons of CO2 per hour. The flue gas the steam plant produces is roughly 7.5% CO2 by volume. In order to study CO2 capture from this flue gas, a tap has been installed on the main exhaust duct which draws a sample of the flue gas into the pilot scale scrubbing column. Figure 2, a simplified diagram of the steam plant, shows that the tap was installed between the economizer and the stack condenser.

Jan 1, 2019

By D. Tahija

"Carbonic acid prepared on-site from carbon dioxide gas is widely used in water treatment and increasingly in some industrial applications. It has not seen extensive use in mineral processing but is an attractive alternative to sulphuric acid for pH control, with the need to counteract high pH levels caused by cemented backfill of particular interest. The fundamental chemistry of carbonate solutions as applied to flotation and flocculation circuits is described as well as plant-scale application. A project to introduce use of carbon dioxide for pH control at the Hecla Greens Creek lead-zinc-silver-gold operation is planned to begin operation in the first half of 2015. INTRODUCTION Flotation pH Control and Backfill Most sulphide flotation circuits are run at pH values ranging from slightly acid to strongly basic, with slightly basic pH the most common. Lead sulphide circuits are typically run at values from 7.5 to 9, with zinc circuits running at higher values of 9.5 to 10.5. This has been the case with ores that produce a natural pH in the circumneutral range, so that the pH needs to be raised. Although lime [Ca(OH)2] is the cheapest reagent in use to raise pH, soda ash (Na2CO3) or caustic soda (NaOH) are also employed where sodium ions in solution are preferred to dissolved calcium, or, in the case of soda ash, the presence of carbonate is desired. The use of soda ash for pH control in lead circuits has been widely recommended for many decades (1). The situation is necessarily different at operations where cemented backfill is used in underground mines (2). Backfill, whether emplaced as rammed paste or pumped slurry, is composed of mill tailings mixed with around 10% Portland or similar cement. When later mining occurs near or adjacent to previously backfilled areas, a considerable amount of old backfill is inevitably mixed with new ore and shipped to the mill. Depending on orebody geometry, mining methods etc., the amount of backfill in mill feed can easily approach 20%, with periods of higher content not unheard of. The presence of so much backfill, with its high cement content, produces results largely indistinguishable from adding a large amount of lime to run-of-mine feed: mill pH in the grinding circuits can range above 11 and high concentrations of calcium ions are present. The need to raise pH disappears; the problem becomes to lower it."

Jan 1, 2015

By Harold Potter

(1) A great deal of experimentation has been carried out by the Wet Process Cement Manufacturers in connection with additives which make possible the production of a pumpable slurry at reduced moisture contents. We ourselves have made dozens of tests both at Laramie, Wyoming and Monolith, California. (2) The viscosity or pumpability of a slurry at a definite moisture content and fineness seems to depend on two basic phenomena. One is the physical structure of the raw material itself, which on fine grinding may or may not be excessively hydrophilic (water adsorptive). Usually crystaline or glassy raw materials are non- hydrophilic. The fine grained amorphous raw materials such as shales and clayey limestones very frequently are, however. (3) The second basic phenomenon affecting the hydrophilic tendencies of the raw material is the presence of certain soluble salts, especially gypsum and small amounts of alkalin carbonates or oxides. (4) Various soaps, and phosphates can be used to produce a pumpable slurry of low moisture content when using hydrophilic raw materials as well as can other proprietary materials such as certain long chain carbon compounds. Too frequently however, the price of such additives in conjunction with the amount required prohibits their use in the cement industry.

Jan 1, 1959

By D. Tahija

"Hecla's Greens Creek silver-gold-lead-zinc mill began using carbon dioxide rather than sulphuric acid to control pH in April, 2015. High pH levels in the grinding and lead flotation circuits are caused by the presence of re-mined cemented paste backfill in mill feed and need to be lowered to achieve good flotation response. Carbon dioxide has proven to be quite effective at controlling pH in the lead circuit with greatly improved pH target attainment. The allowable amount of carbon dioxide used is not limited by effects on lead-zinc selectivity and by poor froth characteristics, as was the case with sulphuric acid. Startup and implementation went smoothly, with few operational issues needing to be resolved. Early results from implementation of the system and its effects on mill performance will be presented. INTRODUCTION Hecla Greens Creek is a silver-gold-lead-zinc mine producing flotation lead and zinc concentrates, as well as a gravity gold concentrate. Besides their base metal contents, both the lead and zinc concentrates carry precious metals. The circuit is largely conventional, with SAG and ball mill grinding being followed by graphite removal preflotation, then conventional lead flotation and conventional zinc flotation. Both rougher concentrates are treated in regrind steps, followed by cleaner flotation. The cleaners tails are treated in an unorthodox bulk circuit to produce a low-grade zinc-lead concentrate marketed to Imperial Process smelters (1). BACKGROUND Backfill and Flotation pH The Greens Creek mine is an underground operation in which mined areas, after ore extraction, are backfilled, using rammed paste or pumped slurry. The backfill consists of mill tailings to which approximately five percent Portland or similar cement is added to enhance its compressive strength. Later mining near backfilled areas inevitably results in a considerable amount of old backfill being mixed with new ore before being shipped to the mill. Depending on orebody geometry, mining methods etc., the amount of backfill in mill feed is often 20% to 25% and sometimes even higher. Commercial cement, and consequently backfill prepared using it, contains excess lime. Because of this, backfill in mill feed is indistinguishable from the addition of a large amount of lime, so mill natural pHs often range above 10 or even 11. Similar situations have been recognized for many years at mines throughout the world (2)."

Jan 1, 2016

By John T. Gormley, Pressley L. Campbell, Harry L. Crouse

INTRODUCTION This paper summarizes an investigation conducted to determine the relationship, if any, between reported occurrences of abnormal levels of carbon dioxide (C02) gas and the construction of a 2.44meter diameter main sewer tunnel under South Eighty-Fourth Street, West Allis, Milwaukee, Wisconsin. Specific objectives of the study were to determine: (1) the sources of C02, (2) the significance of each C02 source, (3) how C02 could move to areas where it was reported to occur in abnormal concentrations, and (4) what actions could be implemented to eliminate elevated C02 levels associated with the tunneling operation. To accomplish study objectives, expertise from several scientific and engineering disciplines was required including chemistry, geochemistry, microbiology, hydraulics, and hydrology. Pertinent documents were reviewed and field data pertaining to each aspect of the study were collected as required and examined to evaluate existing conditions. Background On or about February 1, 1971, gas with a composition different from normal atmospheric air was reported to enter basements and wells of residences in the vicinity of South Eighty-Fourth Street, West Allis, Wisconsin. Examination of the gas composition revealed that it possessed an elevated concentration of C02 and a depleted concentration of oxygen (02). Public health officials who investigated the appearance of the objectionable gas concluded within reasonable certainty that the elevated C02 concentrations were associated with the tunnel construction under Eighty-Fourth Street.

Jan 1, 1979

By James O'Brien, Lyman Frost, S. Elangovan, J. Stephen Herring, Joseph Hartvigsen, Carl Stoots, Anthony Nickens

"Carbon dioxide recovered from concentrated sources, such as metallurgical reduction furnaces, cement kilns and fossil power plants can provide a valuable feedstock for a synthetic fuels industry based on energy from nuclear, solar, wind and hydropower sources. High temperature co-electrolysis of CO2 and steam to produce synthesis gas has been demonstrated using reversible solid oxide fuel cell technology. Where a source of high temperature process heat is available, such as from an advanced high temperature nuclear reactor or solar dish concentrator, the endothermic electrolysis reactions can utilize both thermal and electrical inputs in such a way that the conversion efficiency within the cell is 100%. Synthesis gas produced in a coelectrolysis cell has been further reacted over a catalyst to produce conventional hydrocarbon fuels. Widespread implementation of synfuel production from CO2 will enable a much larger reliance on intermittent renewable energy than can be accommodated by conventional electric demand profiles.IntroductionFor the past several years, Ceramatec, Inc and the Idaho National Laboratory (INL), have been studying the feasibility of high temperature solid oxide electrolysis for large-scale, nuclearpowered hydrogen production under the U.S. DOE’s nuclear hydrogen initiative (NHI) as an alternative to the thermochemical process. Parallel to this effort, the INL and Ceramatec have been researching high temperature co-electrolysis of mixtures of steam and CO2 to produce syngas:"

Jan 1, 2008

By W. K. Collins, C. L. Dahlin, D. C. Dahlin, W. K. O’Connor, G. E. Rush

Direct mineral carbonation has been investigated as a process to convert gaseous CO2 into a geologically stable final form. The process utilizes a slurry of water, with bicarbonate and salt additions, mixed with a mineral reactant, such as olivine (Mg2SiO4) or serpentine [Mg3Si2O5(OH)4]. Carbon dioxide is dissolved into this slurry, resulting in dissolution of the mineral and precipitation of magnesium carbonate (MgCO3). Optimum results have been achieved using heat pretreated serpentine feed material and high partial pressure of CO2 (PCO2). Specific conditions include: 155°C; P002=185 atm; 15% solids. Under these conditions, 78% conversion of the silicate to the carbonate was achieved in 30 minutes. Process mineralogy has been utilized to investigate the appropriate feed characteristics, identify the process products, and interpret the mineral dissolution and carbonate precipitation reaction paths.

Jan 1, 2001

By W. K. Collins, C. L. Dahlin, D. C. Dahlin, W. K. O’Connor, G. E. Rush

Direct mineral carbonation was investigated as a process to convert gaseous CO2, into a geologically stable final form. The process utilizes a slurry of water, with bicarbonate and salt additions, mixed with a mineral reactant, such as olivine (Mg2SiO4) or serpentine [Mg3Si2O5(OH)4]. Carbon dioxide is dissolved into this slurry, resulting in dissolution of the mineral and precipitation of magnesium carbonate (MgCO3). Optimum results were achieved using heat-pretreated serpentine feed material and a high partial pressure of CO2 (Pc02). Specific conditions include 155°C, PC02 = 185 atm and 15% solids. Under these conditions, a 78% conversion of the silicate to the carbonate was achieved in 30 minutes. Process mineralogy was utilized to investigate the appropriate feed characteristics, identify the process products and interpret the mineral dissolution and carbonate precipitation reaction paths. Key words: Mineral carbonation, Carbon dioxide sequestration, Carbonates

Jan 1, 2003

By Tim Martin, Dave Tahija

"In April, 2014, Hecla's Greens Creek mill, near Juneau, Alaska, switched from sulphuric acid to the use of dissolved carbon dioxide for lead flotation circuit pH control. The Greens Creek mine uses paste backfill, in which mill tailings are mixed with cement and used to fill mined areas. Some backfill inevitably becomes part of mill feed during subsequent mining cycles, resulting in high feed pH levels and increased dissolved calcium in the lead flotation circuit. Sulphuric acid is traditionally used to lower pH in such cases but it produces undesirable side effects, including poorer lead-zinc separation and unstable froth. The amount of sulphuric acid used at Greens Creek was limited due to these effects, resulting in higher than target pHs when feed backfill content was high. Dissolved carbon dioxide can be added without these limitations so pH levels have been under much better control since the switch. Additionally, lead-zinc separation and froth characteristics have significantly improved.IntroductionThe Greens Creek Mine, owned by Hecla Greens Creek Mining is an underground mine located on Admiralty Island near Juneau, Alaska, producing silver, gold, lead and zinc in the form of lead and zinc flotation concentrates and a gravity gold concentrate (McDonald, Morgen & Hancock, 2012). The lead and zinc concentrates are produced in conventional flotation circuits preceded by a graphite removal flotation step.The underground mine utilizes cemented paste backfill, of which a certain amount is inevitably re-mined in later mining cycles and returned to the mill, mixed with fresh ore. The Portland cement used in the paste backfill is highly basic so that, from the point of view of the mill, the net effect is to introduce a good deal of lime to run-of-mine mill feed, producing a very high natural pH. This high pH needs to be lowered to obtain good metallurgical results."

Jan 1, 2016

By G H. Park, Y J. Jun, J H. Park

The carbon solubility of the CaO-Al2O3-FeO-SiO2-MgO slag, the main system formed in the Ruhrstahl-Heraeus (RH) vacuum degasser, was measured at 1873 K to understand the effect of slag compositions on the carbon contamination in the ultra-low carbon (ULC) steels. The stable form of carbon was demonstrated to be carbonate by plotting the log [(wt%C)/aC] ratio against the log p(O2) which ranged -11 < log p(O2,atm) < -9. The carbon solubility of the CaO-Al2O3-FeO-SiO2-MgO slag can be estimated using thermodynamic model. The distribution ratio of carbon increased with increasing concentration of FeO due to the FeO reduction reaction and increased basicity of slag. The carbonate capacity of the CaO-Al2O3-FeO-SiO2-MgO slag can be expressed as a linear function of the activity of lime and the optical basicity.

Jun 19, 2024