Search Documents

By L. Diestelow

Evaporation and crystallization processes are used extensively in the mining industry to provide many pro-ducts. In the case of solution mining evaporators are used to concentrate, or to concentrate and crystallize the raw materials being mined. In the case of underground, or strip mining dissolving and crystallization are used in many processes in order to purify the ore to saleable materials. Presently evaporators and crystallizers are being used in the production of sodium chloride, potassium chloride, sodium carbonate, sodium sulfate, lithium chemicals, aluminum, and many others. The evaporator is a device designed to remove water or solvent from a solution. In an evaporator the energy released by steam condensing on one side of the heat transfer surface is transferred to the product solution on the other side of the heat transfer surface. As long as the boiling temperature of the product liquor is below the condensing temperature of the steam, the product solution will absorb heat. This heat absorption causes vaporization of the water (solvent) in the product solution resulting in concentration of the product. The simplest evaporator is the single effect evaporator. If we assume the feed introduced into the single effect evaporator is at its boiling point, ignore radiation losses, and assume the steam into the heat exchanger is dry and saturated, then the heat transferred will correspond to the latent heat of vaporization. Therefore, one kilogram of condensing steam will produce one kilogram of evaporation. Economies in energy usage compared to the single effect evaporator can be made by using multiple effect evaporators, or vapor recompression evaporators.

Jan 1, 1993

By Vynne J. F

Drill monitors for blasthole and exploration drills have been available to the mining industry since the 1970s. The early monitors were pen strip chart recorders which were developed for the oil drilling industry and adapted to mining. They recorded drilling parameters such as depth, pull-down pressure, torque, RPM, and bailing air pressure. While these recorders could generate a large volume of paper, the amount of useful data was minimal. The data was not summarised and required an engineer to interrupt the chart traces. Being a mechanical recorder, the devices were also susceptible to frequent failures.

Jan 1, 1993

By Andrzej M. Wala

A prototype expert system for planning and designing an underground coal mine has been developed in a doctoral study at the University of Kentucky. This prototype expert system for underground coal mine planning and designing consists of a number of knowledge bases concerning different elements of design (e.g., ground control, excavation and bulk materials handling, ventilation, etc.). The objective of this paper is to present the development process of the ventilation design knowledge base for this prototype. This expert system prototype is intended for building an instructional expert system for underground coal mine design. Therefore, the undergraduate course on mine design has been used as the basis, for its development. Because of the availability of knowledge and expertise, this research study has been limited to development of a knowledge model for the Appalachian coal mining region.

Jan 1, 1993

By J. A. Frew, G. I. Orrock, R. M. Glen

The zinc flotation circuit was sampled to provide sized information on its metallurgical performance. A good balance was obtained and the roughing, scavenging, cleaning and regrind sections were assessed. Substantial losses of sphalerite occurred in all sizes. The limitations were poor recovery in the cleaning section which resulted in substantial recycling of 15-30µm sphalerite and iron sulphides, and inability to float +38µm sphalerite in the roughers. Regrinding increased sphalerite recovery by 7% with no loss in grade. Liberation measurements enabled balances for six size fractions to be calculated and the role of liberation on the metallurgical performance was assessed.

Jan 1, 1993

The second annual RMCMI Mine Rescue Performance Evaluation was held in conjunction with the 1993 RMCMI Convention at Beaver Creek. [ ] Six teams participated in this year's evaluation; BHP Minerals, Navajo Mine, Fruitland. NM; BHP Minerals - LaPlata Mine. LaPlata, NM; BHP Minerals - San Juan Mine. Waterflow. NM; The Coteau Properties Company - Freedom Mine, Beulah. ND; Cordero Mining Company, Gillette, WY; and The Falkirk Mining Company - Falkirk Mine. Underwood, ND. The Western Energy Company of Colstrip, MT was represented through observers and evaluators. [ ] Realistic industrial related scenarios, closely simulating the stress of actual rescue incidents, were provided by members of the Eagle Valley Ambulance Service. Five different scenarios were presented to each team on the first day of the evaluation and three on the second. Each team was given the pertinent information to solve the problem as they assembled at the scenario site. The scenarios were going on simultaneously and each team was unaware of the circumstances until they entered the scene. Interested onlookers were afforded the opportunity of viewing the actual simulated rescue operations as they occurred. The teams received valuable pointers and direction from the ream of evaluators following each scenario. They were are also given the opportunity to observe the other teams in action and to meet with the members of all the teams to share information and ideas during team meetings per the predetermined schedule. The primary goal is to recognize current rescue skills, knowledge, and abilities of participating teams. In doing this, each team was provided with individual evaluations and a path for improvement as needed. Each team was recognized for their efforts at an awards breakfast on the final day of the evaluation. New innovations in rescue equipment were introduced and demonstrated for interested teams following the awards program. The importance of progressive training such as what we are witnessing at evaluations during the RMCMI conventions cannot be stressed strongly enough. These teams are the providers of immediate rescue and medical care for victims of accidents at their respective properties. Every mining operation has the potential for very serious accidents due to immense size of equipment and mining logistics. These rescue teams must be prepared to act with the most immediate, professional and knowledgeable actions to save lives and prevent further injuries. Safety is a primary concern of every mining operation and the mine site rescue team is an integral part of that safety effort. The evaluation program is very appreciative for the financial support of the following businesses to enable this program to continue: Safety Master, Acme Welding, North American Coal, Triune. Cummins, OK Tire. Modern Industrial, The Industrial Company, Mine Safety Appliances (MSA), Biomarine, Personal Safety Enterprises, Inc., and Blattner Construction, Thank you again for your much needed assistance. Plan to be a part of next year's Mine Rescue Evaluation Program as a participant or an observer. You will be amazed at the skill levels of the Rescue Teams. See you next year! Linda G. Ash The falkirk Mining Company [ ]

Jan 1, 1993

By H. J. H. Pieterse

This paper highlights the mineralogy of the Barrick Goldstrike Mines Inc. area. The mine is located at the north end of the Tuscarora Spur and is part of the Bluestar/Goldstrike subdistrict of the Carlin Trend. The Betze, Post, and Meikle Mine are major deposits located in the area. The deportment of gold, its leachability, and various process options are also evaluated. Particular emphasis is given to the practical and economic considerations of ore control, and routing of ore to a process option.

Jan 1, 1993

The South Comet mine is an underground silver-lead-zinc mine located on the West Coast of Tasmania with an annual production in the order of 35 000 tonne per year. All ore mined is shipped to the Rosebery mill by road, a distance of 17 km.

Jan 1, 1993

By Mohummad Akram

Statistical analysis of multi-seam mining case studies demonstrated that geologic structure and lithological type and sequencing were predominant factors in entry failures. Finite element analysis was used to evaluate the effects of stress field changes on entry instability under differing geologic conditions. Analysis showed the roof to be particularly vulnerable to shear with the location of the failure site changing to meet loading and geologic conditions. Effects of external support on roof stability were examined. Results were correlated with field data to determine stress levels at which failure could be expected to occur. Based on this research design, criteria were developed for roof stability evaluation under specified interactive loading conditions.

Jan 1, 1993

Acid rock drainage (ARD) derived from sulphide oxidation and the associated metal leaching is the most significant environmental issue facing the mining industry today. Under given hydrological and biogeochemical conditions, the local geology and mineralogy largely control the formation of ARD. The involvement of a geologist is therefore essential in minesite ARD assessment and prevention. The relevant tasks that a mine geologist may undertake at three major phases of a mining project are briefly described. Additional knowledge that a mine geologist should acquire in order to achieve proficiency in ARD assessment is also suggested.

Jan 1, 1993

By L. W. Laage

MFIRE is a mine ventilation and fire interaction computer simulation program. It allows transient state ventilation simulation and features mass based flow rates, natural ventilation, air recirculation, fan curve fitting, airflow reversal and product of combustion tracking. MFIRE was designed to accommodate the needs of the mining industry for routine ventilation calculations and mine emergency planning. This paper describes recent work by the Bureau and MTU to improve MFIRE by incorporating humidity in the mass flow and heat exchange calculations, a data file preparation program and variable reference density in the network calculations. Recent bug fixes are also discussed.

Jan 1, 1993

By Concha F, Sampaio R

In most of the literature, the hydrocyclone is viewed as a black box in which only global variables are present and where the equations are obtained by curve fitting. Recently some work has appeared where the Navier Stokes equations are solved numerically in the hydrocyclone geometry. However, in all of these works the air core surface, which has an important influence on the hydrocyclone dynamical behaviour, is modelled as being a cylindrical surface of fixed radius. In this work, we model the surface of the air core as a free-boundary which has to satisfy a jump condition, the Young-Laplace equation, relating the physics to the geometry. Based on this model, we are able to explain, qualitatively, some phenomena that have puzzled research workers in the field for many years, and can show, through the air core behaviour, the influence of material parameters on the performance of the hydrocyclone.

Jan 1, 1993

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

5.1 TECHNOLOGY FOR INJECTING GROUT INTO BOREHOLES The grouting of fractured rock aquifers is carried out in separate stopes' whose size is determined by the hydro¬stratigraphy and the hydrogeologic properties of the rocks. The number of grouting stopes required depends on the number of intervals in the hydrogeological section. Each grouting stope can include one or several aquifers. Com¬bining several water-producing strata into one stope is pos¬sible only when the values of their permeability coefficients are very similar. In order to achieve efficiency, as many aquifers as possible are included in each stope. In practice, the length of a grouting stope in a borehole usually ranges within 10 to 40 m, but occasionally up to 100 m or more. When conducting grouting operations through boreholes drilled from the face of underground workings, the stope's size can be determined by the thick¬ness of each fractured zone (fault) or by the length of the hole if the entire rock is fractured. Injecting grout into separate intervals of fractured rock can be done from the bottom to the top with ascending stopes or from the top to the bottom with descending stopes. Injection from bottom to top is always preferred. Injection also can be accomplished in separate fractured permeable horizons in the section. The STG integrated grouting method is based on the use of packer and injection equipment and technological schemes that facilitate injection in highly isolated fractured aquifers. For this purpose STG has developed a standard series of packers. 5.1.1 INJECTING GROUT THROUGH BOREHOLES DRILLED FROM THE SURFACE Grout can be injected according to one of four techno¬logical schemes depending on the depth of the fractured aquifers, their hydrogeologic properties and the availability of grout injection equipment if the area is remote (Fig. 43). In the first and most preferred technological scheme (1), the grout is injected from the bottom up with ascending stopes. When this scheme is employed, grouting holes are drilled to the entire projected depth based on the field investigations injection tubes is installed above the top of the first hydrostratigraphic unit to be grouted. This scheme al¬lows the grout to be injected only into the permeable stra¬tum or strata isolated by the packer near the bottom of the hole; it precludes the need to clean or redrill the hole before injecting grout into the next overlying stope. This ascending stope scheme is preferred because of its simplicity and ef¬ficiency. It is used in most of the grouting of saturated fractured rock for the purpose of isolating aquifers while excavating deep mine shafts in the USSR. The second technological scheme (II in Fig. 43) injects the grout in sequence from top to bottom with descending stopes. Injection under this scheme is accomplished through the hermetically-sealed mouth of the hole. It is most advis¬able to grout with descending stopes in saturated fractured rock wherein the aquifers constitute thick networks of frac¬tures. Under these conditions it is practically impossible to drill a grout hole to the entire depth of the underground workings due to the large production rate of ground water. In conducting isolation operations with descending stopes, additional work (relative to ascending stopes) is necessary to drill out the grout in order to create and inject the next stope. As a result, the total amount of drilling required to drill out grout can even exceed the volume of drilling of original rock. Consequently it is advisable to use this inefficient scheme only for injecting grout into holes that contain prolific frac¬tured aquifers at depths less than 150 to 200 m. The third and fourth technological schemes (III and IV in Fig. 43) are used in the selective grouting of separate aquifers. For example, these methods would be applied when a grout hole is drilled to its entire depth, wherein grouting of the upper aquifers must be done first so that the sinking of the first shaft can begin prior to deeper grouting. The third technological scheme is used for the selective injection of grout into an aquifer with a thickness of up to 5 m. For this work the DAU-1-2 removable dual packer is installed. It is lowered into the borehole on an injection pipeline. For aquifers with thicknesses of more then 5 m, the selective injection of the grout is carried out according to the fourth technological scheme; a combination of the DAU-2 hydrodynamic plug and the DAU-1 packing device is used. In order to implement this injection scheme, the DAU-2 hydro-dynamic plug is installed at the bottom of the fractured aquifer and the DAU-1 packer is installed at the top of the aquifer.

Jan 1, 1993

The investigations described in this paper aim at the development of a new impact mill. The objective is to produce particle size distributions below 10 .tm without using an air classifier. Circumferential rotor speeds of up to 200 m/s are strived for.

Jan 1, 1993

By Raymond PoIick

The Demag Electric Slag Cleaning Furnace installed at the Asarco Smelter in Hayden Arizona is one of the few rectangular electric furnaces now operating. The long transition times from charge to tap allow exceptionally clean skims (high recovery); however, the furnace design is complex. Additional Asarco requirements for rapid installation and commissioning further complicated the design. When operating and wear effects accumulated after two years of use, steps were taken to rebuild the furnace with enhanced durability based on the design parameters experience in actual use.

Jan 1, 1993

By A. F. Barsotti

Apart from jewelry, holistic apparel, and special collections of color and sometimes rare crystal specimens, the average layperson has little or no appreciation of the omnipresence of minerals or mineral derived products in the home. From concrete in the driveway to aspirins in the medicine cabinet, minerals, especially industrial minerals, play a major role in day to day living. For a better appreciation of this let's look into the a day of the life of a fellow named John, and see how much we depend on industrial minerals. The sounds of soft violins nudged John from his sleep. The melodic sounds of Beethoven's Pastoral coming from his radio alarm clock brought him out of his dreams. He reached for the reading light switch, then checked his watch--6:30 a.m., and another day of work. As he got up, the darkness outside reminding him of winter coincided with the soft voice of the all night disk jockey forecasting the fall of four inches of snow. Warm beads of water beating on his face removed all remnants of sleep and, like a stimulant, the morning shower brought thoughts of yesterday and plans for a new day. These carried over as he looked himself in the mirror while shaving and brushing his teeth.

Jan 1, 1993

By Jim A. King

The total pressure oxidation of copper concentrates is a potentially viable option for treating copper concentrates that are either low grade or contain significant impurities. Both concentrate types are heavily penalized in smelter contracts. The total pressure oxidation process involves autoclaving the copper concentrate at temperatures of 200-220 C under oxygen pressure. The autoclave discharge can be separated into a solid (oxidation residue) and a liquid (oxidation solution) product. The oxidation solution can be treated for copper recovery by solvent extraction - electrowinning or by direct electrowinning. The direct electrowinning recovery of copper requires prior removal of selenium and tellurium by cementation on finely divided scrap copper. The oxidation residue is washed thoroughly to remove acid and dissolved copper prior to precious metals recovery by conventional cyanidation in the presence of lime. The results of a benchscale investigation involving a number of copper concentrates are reported. Copper recoveries in autoclave oxidation and gold recoveries by cyanidation of the oxidation residue exceeded 99%. The results of benchscale experiments to demonstrate copper recovery are described. Various flowsheet options are presented.

Jan 1, 1993

By S. N. Rossovsky

"A new method for the hydrometalfurgical treatment of refractory gold arsenosulphide concentrates is presented. Themethod involves a combination of' finegrinding, intensive agitation, flotation, and cyanidation, and consists of leaching of -10u pyrite and arsenopyrite particles in alkaline solution under intensive agitation without the application of costly high-pressure and roasting techniques. Consistent extractions of gold, in excess of 96%, are achieved.IntroductionConventional methods of alkaline leaching of gold arsenosulphide concentrates in an autoclave» and under electrochemical oxidation( 2) require expensive equipment as well as high-cost energy and reagents. In other cases, processing of gold concentrates inelude: ultra-fme grinding, calcination at 200°C to 250°C with the addition of an oxidant (NH4NOJ followed by alkaline leaching of the resulting calcine with hydrogen peroxide, the latter being a complicated method yielding poor extractions of gold (89% to 90%). In this paper, a hydrometallurgical method is described for processing refractory gold arsenosulphide concentrates in which alkaline leaching is followed by cyanidation of the residue."

Jan 1, 1993

By Khosia NK, Ravishankar SA, Sankar TAP

Alumina reduction in Rajhara iron ore slimes essentially involves separation of hematite from gibbsite in relatively coarser fraction and from kaolinite in the finer fraction. Selective dispersion flocculation studies on synthetic mixtures clearly indicated that while it was possible to achieve almost perfect separation of hematite from kaolinite using starch and PAMX (modified polyacrylamide containing hydroxamate functional groups) flocculants, no selectivity was observed in iron oxide-alumina system. A schematic flowsheet suggested on the basis of this work for the beneficiation of Indian ore slimes thus consists of classification in a hydrocyclone, followed by selective dispersion of coarse fraction (underflow) and selective flocculation of the overflow fraction. Starting with a feed assaying 46 per cent Fe and 11.6 per cent A1203, a concentrate assaying 60 per cent Fe and 4.7 per cent A1203 could be produced at an overall iron recovery of 60 per cent using conventional Reagents.

Jan 1, 1993

By John J. Moore

This paper discusses the application of a video technique to construct stability diagrams for the combustion synthesis of ceramic-metal composites. Several model exothermic combustion synthesis reactions have been used to investigate the effect of the reaction parameters, eg. stoichiometry, green density, etc, on the stability of the propagating combustion reaction front and subsequent product morphology. The effect of varying the reactants and their stoichiometry to provide a range of reactant and product species ie. solids, liquids and gases, in the synthesis of both dense and expanded (foamed) ceramic and ceramic-metal composites was also investigated with respect to their corresponding combustion front stabilities.

Jan 1, 1993

By D. D. Murphy

The Bureau of Mines has studied the mechanism of shear-flocculation of silica with stearic acid. At pH 6 and 12, shear-flocculation of silica was not observed with up to 10-4M (5 lb/st) stearic acid. However, in the presence of 0.1 M NaCl at pH 6, shear-flocculation was observed at stearic acid concentrations 10-4 M (5 lb/st). Adsorption of stearic acid on silica was studied using stearic acids spin-labelled with a doxyl group. The presence of the spin-labelling group did not greatly affect the shear-flocculation properties of stearic acid. Adsorption of labelled stearic acid on silica was measured as a function of surfactant concentration with electron paramagnetic resonance (EPR) spectroscopy and gas chromatography (GC). The GC results indicate the stearic acid was predominately adsorbed on the surface at concentrations above 10-4 M. From the EPR spectra, the formation of aggregates of stearic acid was apparent at concentrations of approximately 10-414 (5 lb/st). The results are discussed in terms of a possible mechanism for shear-flocculation.

Jan 1, 1993