Search Documents

By West-Sells P, King J. A, Patel C

The Eskay Creek orebody is located in north-central British Columbia (Canada). The ore contains major gold and silver values and minor but economically significant quantities of zinc. The refractory nature of the gold necessitates a pressure oxidation pretreatment prior to cyanidation. After solid-liquid separation the oxidation solution can be treated by oxyhydrolysis for iron removal and cementation with zinc dust for noble element removal. The resulting solution, as obtained in pilot studies, contains 7 - 10 g/L Zn, 0.5 g/L Ca and 2 - 4 g/L Mg. Minor amounts of cadmium, copper and iron may also be present in the solution. Over 90 per cent recovery of zinc from Eskay Creek oxidation solutions could be obtained by four stages of zinc extraction with Cyanex 302 extractant (Cyanamid Canada Inc, Niagara Falls, Canada). Zinc was stripped from the organic with spent zinc electrolyte in two stages. A complete description of the bench scale and miniplant studies of the solvent-extraction electrowinning circuit follows. The behaviour of minor amounts of copper, cadmium and iron in the circuit is also Discussed.

Jan 1, 1993

By S. Chander

The advantages and disadvantages of various techniques available for controlling reagents in the mineral flotation systems are discussed. Special interest is placed on potentiometric and voltammetric sensors for monitoring flotation pulps. Different approaches to increase the sensitivity of detection and to facilitate in-stream monitoring of solution species are also discussed. The potentiometric sensors are simple to use but are limited by the availability of an electrode reversible to the species to be monitored. In some cases the response signal could be unreliable due to the presence of interfering species. In comparison, voltammetric sensors require a higher degree of instrumentation which, however, provides an opportunity to decrease interferences and increase levels of detection.

Jan 1, 1993

By A. Heriba

Cyanide is highly toxic to humans and other organisms. Concentrations of RCN as low as 0.05 ppm can be lethal to fish (Scott and Ingle', 1981). In wet climates and in colder climates where natural degradation is slow, it is becoming mandatory to destroy cyanides in effluents before they can be discharged. The disposal of spent gold ore as tailings from cyanide heap leach processing facilities is a matter of concern to the public, the mining industry, and regulatory agencies. South Dakota mining laws and regulations require that spent ore be neutralized to a suitable level with respect to cyanide before disposal (Durkin, 1990). To safeguard the environment and protect ground-water and surface-water supplies adequately, a reliable test is needed to determine the amount of cyanide in the solid spent ore.

Jan 1, 1993

By M. Misra

Acid mine drainage from reactive sulfide tailings is a major environmental concern facing the mining and mineral industries. A preventive technique to control acid mine drainage by agglomeration and encapsulation process is presented in this paper. The reactive tailings are agglomerated using Portland cement type I1 as binder. The cold bonded agglomerates after specified curing period are, strong and resistance to weathering. The leaching and weathering experiments have shown that a significant reduction in the concentration of dissolved metals can be observed with the agglomerates as compared to as- received tailings. Addition of small amount of sodium silicate during agglomeration increases the strength and develop good resistance to weathering by forming a glassy coating and elongated crystals within the agglomerates.

Jan 1, 1993

By Ken Fiorentino, Gordon F. Revey

H3 Tunnelers recently excavated two conventional 48 foot diameter highway tunnels through the Halawa side of the Tran-Koolau Mountains on Oahu. The primary blast design challenge on this Job was minimizing overbreak In the alternating layers of pahoehoe and aa lava, clinker, end tuff. Two different excavation techniques were evaluated in the Halawa tunnels. The first method used drilling and blasting to excavate the tunnels to within one foot of their final perimeter. A roadheader, mounted on a backhoe, was then used to excavate the remaining foot of ground. The second method used conventional smoothwall blasting techniques, without any mechanical excavation. This paper describes the details and relative success of the two excavation methods tried in the Halawa tunnels.

Jan 1, 1993

By A. H. Balch

A physical elastic seismic model, based on the Peoria oil field was constructed and used to produce multi mode cross-borehole seismic data. Because this was a physical model, it was necessary to deal with a complex wave field consisting of compressional waves, shear waves, and converted waves. The recorded raw data were complex, have no resemblance to the inter-well geology, and were difficult or impossible to interpret. These unintelligible data sets were extensively computer processed. Detailed, accurate, images of the inter-well structure, and reflecting horizons were obtained as a result of this processing. This investigation demonstrates that excellent, accurate images of the inter-well geology can be obtained by skilled seismic cross-well data acquisition and extensive careful computer processing.

Jan 1, 1993

By John C. Morrisey, Harold M. Ray

With full production from the Casteel Mine in 1987 The Doe Run Company, a wholly owned subsidiary of the Fluor Corporation, encountered a significant increase of copper and iron to the Viburnum Mill. This major change of the lead, zinc, and copper metal ratios in the ore created circuit problems which adversely affected concentrate quality. Recognizing the problem, the company embarked on a metallurgical research program to include laboratory, pilot plant, and plant testing. The program developed an innovative copper prefloat process which both increased copper recovery and significantly improved concentrate quality. The process was tested and first operated at Doe Run's Brushy Creek Mill then installed at the Viburnum Mill in 1992. A brief history of development, plant operating data, and other potential applications for the patented processes will be described in the paper.

Jan 1, 1993

By M. P. Brandt, T. P. Knoetze, I. I. M. Kessler

It has generally been accepted that the volatile mater in a coal is the factor that determines whether or not a specific coal dust is an explosion risk. This paper presents the results of an attempt to relate the explosibility index (Kex) of South African coals, as determined in a AD-litre explosion vessel, to the volatile mater content of the coal and the calorific value of the volatiles. A good relationship between the calorific value of the volatiles and the explosibility index was established, which makes it possible to calculate the violence of an explosion, as expressed by Kex, for South African coals. The Kex value is but one of a number of parameters that influence the explosion hazard in a specific colliery and cannot be used as the sole predictor of the propagation of an explosion underground. Other parameters include the ignitability of the coal, temperature, humidity, dispersibility of the dust, methane concentration, amount of incombustibles present, and ventilation.

Jan 1, 1993

By S. C. Suboleski

Forecasts indicate that the acid rain bill currently before Congress is likely to cause an increase in demand of 30 to 40 million tons per year of compliance quality coal from Central Appalachia. This represents a doubling of this segment of the coal business. This paper will examine how this doubling can be met, what the likely implications for pricing are, the major uncertainties associated with these predictions, and the likely outcomes of the growth in compliance coal. Finally, some implications for fuel planners will be discussed.

Jan 1, 1993

Discontinuities often have a very detrimental effect on the stability of mine highwall faces. The west wall of the Muja open cut is remarkable for the number and variety of discontinuity sets which occur over a relatively small area. To-date 14 separate structural domains have been identified over an area measuring approximately 560 m by 120 m.The structural domains have been grouped into four structural assemblages on the basis of their angular relationships to each other and to regional folding and faulting. The distribution of these structural assemblages appears to be erratic and no controlling factors have been identified to explain or predict them other than in the most generalised terms.

Jan 1, 1993

By R. S. Shoemaker

Environmental and regulatory authorities are increasingly requiring that precious metals heap leach piles be contoured before they are abandoned so they may present a more "natural" look to the eye. Depending on the ore type, many of these contoured heaps will be subject to substantial erosion by precipitation events, native plants will have difficulty in establishing themselves and slimes be washed onto surrounding areas or into watercourses. This paper presents the argument that the results of contouring heaps are counter to good environmental practice. Calculations which have been made demonstrate that leveling and berming the heap tops as well as berming the edge of each lift or setback will effectively prevent water erosion and promote the growth of native plant species.

Jan 1, 1993

By Jianliang Li, Xi Peng, Guorong Lu

This paper describes a wind tunnel modelling study on airflow and pollutant concentration in a large open pit mine located in southern China. A 1:1000 scale model of the surface mine was fabricated and placed in a wind tunnel. Airflow velocity in the test section of the wind tunnel can be continuously adjusted from 0.3 m/s to 6.0 m/s. In this study, both the present pit condition and the projected final pit condition were modelled. Airflow direction and velocity profiles were obtained. The impact of wind direction and velocity on airflow was also studied. The pollutant concentration distribution in the open pit was simulated using smoke, and a distribution profile was obtained. Respirable dust concentrations at the mine site were measured, then its concentrations at the projected final pit condition were estimated using the obtained pollutant concentration distribution profile. Under normal meteorological conditions, it is expected that the respirable dust concentration for the final pit should not exceed the government standard. Key Words: wind tunnel modelling, open pit, surface mining, scale model, mine ventilation, airflow profile, point source.

Jan 1, 1993

By Gunder Homstvedt

The paper presents a new method for boring of blind inclined shafts. The machine, called BorPak, developed by The Robbins Company, operates similar to a mini TBM. It is a remote operated, self propelled drilling machine mounted on a crawler for high mobility and launched out of a starting tube for quick collaring. A short history of the operation of the prototype in Scandinavia and Canada is included in the paper. The BorPak is capable of boring raises at angles from 30° to 900 from horizontal in sizes ranging from 1.2m-2m diameter without the use of drill pipe. The BorPak represents an innovative tool for improved performance, reduced costs and creating a safer working environment.

Jan 1, 1993

By Robert Jedrzejczak

The Endako Mine is an open-pit molybdenum mine located in the north central region of British Columbia, Canada, about 960 km (600 road miles) north of Vancouver. Production for the latter part of 1992 was expected to averaged 63.5 kt/d (70,000 stpd). Of that amount, 27 kt/d (30,000 stpd) was the mill feed. This production is achieved with five 11.5 to 14.5 m3 (15 to 19 cu yd) electric shovels, six Euclid R190 and two Unit Rig M120 diesel-electric haul trucks, and three 320 mm (12.25 in.) electric rotary drills. There are three ore zones delineated into pit areas: the Endako, Denak East and Denak West. Present mill feed source is the southeast stage of the Endako Pit. Stripping is carried out in the south wall stage also of the Endako Pit. The mine high grade aggregate is reduced in the primary and secondary crushing circuits before processing in conventional RM-BM-flotation circuits. The majority of the molybdenum sulfide (MoS2) is roasted on site to produce technical grade molybdenum oxide (M003). A portion is further refined and treated to yield a 99.9% pure MoS2 product.

Jan 1, 1993

[COUNCIL FOR 1992/93 President J.P. Hoffman President Elect Dr H. Scott-Russell Vice Presidents Senior J.A. Cruise Immediate Past President R.D. Beck Junior D.A.J. Ross-Watt Honorary Treasurer J.A. Cruise Members of Council Dr N.A. Barcza B.R. Broekman G.A. Brown P.M. Craven Prof. R.J. Dippenaar J.R. Dixon* A.A.B. Douglas B.R. Fleetwood Dr R.V.R. Handfield-Jones P.R. Janisch * co-opted P.J. Knottenbelt R.P. Mohring J.L. Nel* K.C. Owen P.D.K. Robinson K.A. van Gessel D.J. van Niekerk C.J.C.J. van Vuuren* P.M.T. White]

Jan 1, 1993

By F. M. Abdrabbo

Flight auger bored piles are formed by screwing a continuous flight auger into the ground, and pumping cement/sand grout or concrete down the hollow stem of the auger as its withdrawn. The auger is driven at the top by hydraulic or electrical motor and is guided by a vertical crane leader. Loading tests on concrete piles are described. The stability plot method is used to drive the shaft friction and the end bearing load components of the pile capacity. This paper outlines features of crucial construction factors that affect the geotechnical capacity of this type of piles. These factors include, vertical speed of auger during boring, grout factor, grout pressure, number of reborings, type of material, and slump of concrete used to form the piles. Two of these factors are highlighted in this paper. It was found that, shaft resistance is independent of grout factor, whilst point resistance increases as grout factor increases. Nevertheless the engineer should decide the safe pile load associated with the most economical grout factor. High vertical speed of auger during boring of piles may cause disaster for the adjacent buildings, due to soil decompression.

Jan 1, 1993

By F. L. Pirkle, D. A. Podmeyer

The mineral zircon is mined for use as specialty foundry sands, abrasives, ores of Zr02 and zirco¬nium metal, refractories and zirconium chemicals. It is produced as one of several products from heavy-mineral sand deposits associated with ancient shorelines. Because of its low coefficient of thermal expansion, its high melting point, its high refractive index and its chemical inertness, it is an attractive refractory material. Zircon varies from deposit to deposit in terms of grain size, grain shape and chemical purity. Thus, there is a wide range of commercial zircon products that differ in impurity levels, particle shapes and grain sizes.

Jan 1, 1993

By Willey GJ

A brief test program was undertaken to assess the viability of air-sparged hydrocyclone beneficiation at the Cadjebut concentrator. Three different process streams were processed (lead rougher feed, lead scavenger tail and `mine water' solids) in a small scale ASH unit (one litre volume, feed rate 1000 to 1800 kg solids/hour). Analysis of the concentrates indicated that ASH based flotation was successful, selective and capable of achieving improvements to the overall metallurgical performance of the concentrator. The flow regime inside the device accentuates the selective flotation of the finest particle size ranges generally not recovered to any significant extent in conventional mechanical flotation devices. The testwork proved that the ASH is a viable alternative option for increasing the flotation capacity of the lead beneficiation stage of the Concentrator.

Jan 1, 1993

By W. P. Blacutt

A financial-economic model incorporating physical, market, and policy variables is developed for mining investment in Bolivia. Additional risk criteria emanating from political instability. new mining legislation, recent environmental regulations, and a new minerals taxation system are accounted for and are integrated into the investment decision model. Results of the model indicate that geologic and market variables have the dominant effect on the investment-worth function. Among policy variables, exchange rate and taxation policies have the most significant influence. Depreciation allowance for infrastructure development has negligible weight in the investment-worth function. The business structure of the firm considering investing in the Bolivian Polymetallic Project is found to be an instrumental factor in the investment-worth outcome. Specifically, undiversified mining companies whose operations exclude zinc production as the primary source of revenue would benefit most from adoption of this project.

Jan 1, 1993

By James P. Ulery, Jon C. Volkwein

The U.S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on-site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography in the laboratory. These gas results were analyzed for explosibility. Coal samples from various depths were used to obtain the gas content of the coal using the modified direct method. Personal expo- sure to carbon monoxide was also monitored. The highest methane level observed was 9.55%. The levels of inert gas (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were nonexplosive. The gas content of the coal was about 0.30 cm3/g. The maximum personal time-weighted average sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for pre- venting explosions during auger mining.

Jan 1, 1993