Search Documents

By Bloom M. S

Epithermal vein and breccia hosted Au mineralisation at the Kerimenge prospect, in the Wau district, Papua New Guinea, occurs within a block of multiply fractured dacite porphyry of Pliocene age, and is localised on intersecting regional fault structures, marginal to the eroded vent of a Late Pliocene-Pleistocene maar volcano (diatreme).Au mineralisation is primarily controlled by the steeply dipping Kerimenge Fault zone, which hosts a basal zone of silicified breccias,transitional laterally and vertically to networks of fracture controlled veins.Early quartz+pyrite veins, deposited from CO2 rich, NaCl saturated, boiling fluids pre-date the main phase of Au mineralisation. Four stages of Au bearing vein mineralisation have beenrecognised. Quartz+sulphide veins (stage 1) and partially coeval quartz+sulphide+carbonate+ adularia veins (stage 2) occur marginal to silicified breccias, and are associated with quartz+sericite+pyrite wallrock alteration. Similar depositional conditions prevailed for stage 1 and stage 2 mineralisation. Mineralising fluids underwent two stage boiling at temperatures of 145 to 2300 C. Boiling resulted in the loss of approximately 3 wt.% CO to the vapour phase. 2 Fluid salinity was probably I wt.% NaCl or less.

Jan 1, 1990

"Air Products approached LAC Minerals in 1987 to initiate trials with pure oxygen in the leach circuit at several LAC facilities in Canada. This paper gives an overview of oxygen use and covers specific operating data from the Doyon and Terrains Aurifères mills near Val D'Or in northwestern Quebec. LAC also uses oxygen at the Macassa mill in Kirkland Lake, Ontario.In addition to the LAC facilities, oxygen is currently in use for test purposes at the Holt McDermott mine in Kirkland Lake, Ontario and the Camflo mine near Val D'Or.There are two requirements for oxygen in the cyanide leach mill. Firstly, oxygen is required in the familiar gold dissolution reaction as follows:(1) 4 AU (s) + 8 NaCN (aq) + 02 (aq)+ 2H 20(aq) - 4NaAu(CN) 2(aq)+ 4Na OH(aq)Of the reagents on the left side of the equation, the availability of gold is fixed by the ore in question. Obviously, water is available in excess, 1eaving cyanide and oxygen as the limiting constituents in the process. Most mills operate with an excess of cyanide, which is fairly closely monitored. Dissolved oxygen levels, however, are not normally watched very closely and find their own level based on the temperature, the availability of compressed air and the ability of the ore to consume oxygen.Typical D.O. levels are in the 3-8 ppm range, however levels less than 1 ppm are not uncommon for refractory ores.With pure oxygen, dissolved oxygen levels as high as 30 ppm can be achieved. (Figure #1). This greatly accelerates the kinetics of the leach reaction and may also shift the reaction further towards completion thus increasing gold dissolution slightly."

Jan 1, 1990

By G. A. Kosick, G. S. Dobby

"This paper presents the principles and application of a recently developed control system for flotation columns and column circuits. The control system uses triple pressure sensors to directly sense zone densities and level, and to help in characterizing the operating behaviour of individual columns. A complete expert system development tool is incorporated within the system to provide the facility for full operator training, an on-line help facility, and a means for incorporating the column behavioural patterns into decision making rules. The system is configurable to any number of columns and can be run in either supervisory mode or direct control through Minnovex PIO software. Additional process signals can be interfaced with the system if desired. Operating experience with the control system on the Minnovex column flotation pilot plant is described.I: INTRODUCTIONColumn flotation cells have been more difficult to control and are more sensitive to circuit changes than conventional mechanical flotation cells. This susceptibility encouraged investigation into various types of control strategies ranging from inexpensive single pressure measurements for level control, to highly instrumented and expensive systems using a variety of control methods.Flotation operators, in many cases, do not understand the column control philosophy or have not been trained to deal with this new type of cell. Some operators have subsequently absolved themselves of the column operating responsibility. Some column cells, for example, have run for hours with slurry pouring over the top or no froth coming off at all.ColumnEX is a column flotation control system which was developed from the viewpoint of an operating shift foreman who wishes to:1. control the column or column circuit through a genuine understanding of what is happening inside the columns, and2. to share this knowledge with his flotation operators and be available to guide them through times of circuit upsets."

Jan 1, 1990

Ventilation 'is currently used in mines to sustain human life, prevent explosions, and provide a more healthful work place. Future automated-mining systems could use ventilation techniques quite. different from today's practices. The Bureau of Mines is anticipating various methodologies for ventilating the automated mining systems which are now beginning to emerge in the mining industry. This paper examines the special ventilation requirements for automated mining systems. Topics include requirements for automated systems, current studies with blowup ventilation tubing, and ventilation of two types of highwall -ripper type mining machines.

Jan 1, 1990

By Goldie R

The use of options theory in business has become well established in recent years and is currently one of the most exciting areas of current finance research. The theory can be used to value levered firms, and streams of contingent payments. This technique also has very practical applications in the areas of capital investment analysis and the valuation of equities in the natural resource industry. The use of options theory has been well accepted and used for many years in the trading of commodity options and futures contracts, in banking and insurance and in other industries. It also can be used to value such diverse contingent claims problems as the income tax liabilities of the firm and share underwriting agreements.Its application to the more complex options, such as those present in the resource industry, is only now becoming known. This lag is, at least partially, due to the difficult mathematics involved in solving complex options problems. Another factor is the almost overwhelming abundance of uncertainties, such as grade, tons and other natural risks, which must be considered in the evaluation mining projects.

Jan 1, 1990

By R. V. Ramani, R. Bhaskar

One of the primary means of .control of health hazards from respirable contaminants in mine atmospheres is through design and operation of mines to meet mine health and safety regulations and recommended practices. A U.S. National Academy of Sciences study concluded that for significant progress in coal mine dust control, research should be directed more toward obtaining fundamental understanding of the origin, transport and characteristics of respirable coal mine dust. Theoretical and experimental studies on transport of dust in mine airways, particularly coordinated efforts to validate theory with practice, are scarce. Some empirical models, developed on the basis of experimental data, are available but these models cannot be applied to new .conditions. The purpose of this paper· is to present the results of theoretical and experimental studies on the transport and deposition of dust in mine airways. This study is a part of an on-going research project in the Generic Mineral Technology Center on Respirable Dust. In the paper, the assumptions of the modeling phase of the project and the development of a convection-diffusion equation for dust transport in mine airways will be outlined. The important aspect of the modeling effort.is the capture of the deposition phenomenon. The experiments performed under controlled conditions in a typical mine airway as well as under normal mine operating conditions will be discussed. The comparison of the model predictions ·with experimental results will be made to identify critical areas of agreements and deviations. The implications of the findings and areas for further research and development will be identified.

Jan 1, 1990

By John Barakso

The Sam Goosly or Equity silver deposit is fundamental- ly a discovery based on the analysis and interpretation of reconnaissance geochemical samples. The discovery was made by Kennco in an area of heavy forestation and wide- spread cover by thin glacial debris. No major mines had been discovered in the vicinity of the discovery prior to the geochemical reconnaissance, and the interpretation of the geochemical results therefore was based on data available through geologic mapping and the sample collection process. In the period 1959-1961, PE. Hirst and his crew, in 1962- 1965 P.T. Blackand his crew, and in 1966-1967 C.S. Ney and P.T. Black and their crew collected geochemical samples from the area of what is now the ore body. Several of these samples were compiled and reanalyzed in the winter of 1966- 1967 for various trace elements, including fluorine. A strong, almost 16-sq-km (10-sq-mile) fluorine anomaly was projected along with a very weak heavy metal anomaly. On the basis of this anomaly, a chalcopyrite-bearing quartz monzonite was discovered in 1967. This was a misleading, noneconomic discovery not associated with the Sam Goosly discovery. The interpretation of the geochemical data by Barakso that summer indicated that another source was responsible for the fluorine anomaly. The conclusion was based on the assemblage of trace elements. Therefore C.S. Ney recommended further regional soil sampling to check the original data. The early results of this follow-up sampling found over 33 ppm silver. First float, then ore outcrop was found in the area of the silver anomaly. The attached reprints complete the development of the property after the discovery of the outcrop of ore.

Jan 1, 1990

By Raj K. Rajamani, Ilesh M. Shah

Maintaining pH, a routine requirement in many industrial processes, is by no means trivial. The control is troublesome because of the inherent nonlinearity and frequently changing process dynamics. Many researchers in the past have investigated advanced on-line estimation and/or adaptive control techniques to overcome these difficulties. Most methods require the development of a complex mathematical model. The present work deals with the use of a simple and elegant method for pH control, based on the use of fuzzy logic. First, a standard fuzzy-logic controller is discussed, followed by a self-organizing controller. The latter algorithm generates a set of rules based on observation of the process. Thus it is a learning algorithm. The development and application of the algorithms to a laboratory acid-base neutralization experiment are presented. This elegant technique is powerful and deserves attention in mineral pro- cessing.

Jan 1, 1990

By S. R. Droes

The U.S. Bureau of Mines investigated calcium fluoride (CaF2) assisted sulfuric acid (H2S04) leaching as an alternative to the melting-quenching procedure to obtain Mn from domestic manganese silicate resources. Pyroxmangite [(Mn, Fe) Si03] ore containing, in percent, 34.4 Mn, 22.8 Si, 2.6 Ca, and 1.3 Fe was leached in a 500-mL resin kettle. Ninety-six percent of the Mn was extracted under conditions of 330 g/L ore, 245 g/L H2S04, 35 g/L CaF2, 90' C, and 2 h. To incorporate electrowinning in recovering Mn, the ore was leached with a simulated spent anolyte solution containing, in grams per liter, 12 Mn, 140 H2S04, 130 (NH4)2S04 (ammonium sulfate), and 5 CaF2. Manganese extraction of 92 pct was achieved from 130 giL ore leached at 90° C in 3 h. The Fe, silica (SiOJ, and other impurities were precipitated from the pregnant solution by neutralization with ammonia (NH3). Manganese of greater than 99-pct purity was deposited at a cathode current density of 50 mA/ cm2 at 30° C, with a current efficiency of 65 pet in a two-compartment cell. A flowsheet was proposed for the leaching and electrowinning procedure.

Jan 1, 1990

Fossil resin types occurring in the Hiawatha seam of the Wasatch Plateau coal field, Utah, have been separated according to color and their physical and chemical properties evaluated. These resin types were separated into four color fractions, yellow, amber, light brown, and dark brown. Each resin type has then been subjected to comprehensive spectroscopic examination and other physical methods of characterization. Included among the spectroscopic methods of characterization are FTIR and 13C NMR spectroscopy. Physical properties that have been measured include density, optical, and magnetic properties. These analyses reveal that the resins are distinct from other macerals, predominantly nonaromatic in nature with small amounts of oxygen functionalities and a low degree of unsaturation. The four resin types show distinct differences in certain physical and chemical properties such as density, hexane solubility, magnetic susceptibility, and aromaticity.

Jan 1, 1990

By J. C. Judd

The U.S. Department of the Interior, Bureau of Mines investigated solvent extraction methods for recovering gallium from filtrates produced from sulfuric acid leaching of hydrometallurgical zinc residues. These filtrates typically had pH values of 0 to 0.5, too high an acid content for effective gallium recovery by traditional extractants. Of the nine extractants studied in batch tests, 0.3M octyl phenyl acid phosphate (OPAP) in a kerosene diluent was the most effective extractant for gallium recovery, extracting up to 99.9 pct of the gallium. This high extraction was possible when the iron in solution was maintained in the reduced ferrous state. Batch tests also showed that a 1.5M-H2SO4 strip liquor recovered 98 pct of the gallium from the loaded OPAP. A continuous solvent extraction system was designed and operated based on McCabe-Thiele analyses of equilibrium loading and stripping isotherms. When 12 L of leach filtrate containing 0.32 giL Ga and 20 giL Fe were pumped through the system in 32 hr, results showed that 95 pct of the gallium was extracted in four stages at an A:O ratio of 1:1. Stripping the loaded solvent with a 1.5M-H2S04 liquor recovered 94 pct of the gallium in four stages at an A:O ratio of 1:4. A two-stage, 50-pct-phosphoric acid strip successfully removed ferric iron from the OPAP, allowing high gallium extractions to be maintained.

Jan 1, 1990

By D. Su

This paper presents the details and results of a preliminary investigation into the response of borehole pressure cells (BPCs) in soft coal. Two parallel approaches, laboratory calibration and nonlinear finite element simulation, were adopted for deter- mining the BPC K-factor, which was defined as the ratio of cell pressure change to the corresponding change in external pressure. Results from both the laboratory calibration and the nonlinear finite element simulation revealed a nonlinear response of cell internal fluid pressure to external loading. The K-fact& also is shown to increase with increasing setting pressure and decreasing medium modulus. -Depending on the setting pressure, the K-factor for coal having a Young's modulus of 1.6 x lo5 psi ranges from nearly 1.2 at 2,000 psi of external pressure to 1.485 at 8,400 psi of external pressure. The improved under- standing of BPC behavior leads to the more accurate calculation of BPC K-factor in coal which significantly improves the correlation between pillar pressures measured in underground coal mines and those predicted by nonlinear finite element simulations of these pillars.

Jan 1, 1990

Gold at Renco occurs in association with pyrite, pyrrhotite, chalcopyrite and quartz and is confined to a series of brittle fractures and fault breccias (reefs) preferentially developed within an anastomosing ductile shear zone. During late Archaean crustal movements both the orebody and the enclosing host rocks were deformed within a series of east-north-east striking, southerly dipping, shear zones. The reefs within these shear zones are now texturally different to those away from the shear zones, and this difference is reflected by differences in the way the gold is distributed in the two reef types. These differences are not taken irto account by the software package currently being used to generate kriged plans of gold grade and reef thickness and this may explain some of the inaccuracies found in these plans.

Jan 1, 1990

Project cost control procedures and computer systems have enjoyed a successful and simple relationship over the past decade, thanks primarily to the proliferation of portable computers or PC's. Prior to the introduction of this technology, project control was largely a manual and somewhat onerous task of historical data compilations, with little time available for dynamic forecasting, staged planning, or pre-emptive cost control. Automated systems developed during this era were resident on "Heavy Iron" or mainframe computers and were expensive to maintain and operate. Use of these early systems was limited to large engineering, construction, and industrial concerns with the economies of scale and funding required for their successful application. Systems were either designed for critical path analysis or task scheduling, but rarely integrated with the other, much less cost control.

Jan 1, 1990

By R. W. Luhning, S. D. Gittins, J .. A. Haston

"The Underground Test Facility (UTF) project operated by the Alberta Oil Sands Technology and Research Authority (AOSTRA) north of Fort McMurray has achieved marked success in field testing mining access and horizontal well in situ recovery of bitumen from the Athabasca oil sands.Mine access has provided for effective placing and operation of horizontal wells in the oil sands from a tunnel system in the underlying limestone. Performance of the in situ recovery process, Steam Assisted Gravity Drainage, has substantially exceeded forecasts made at the start of the project. Over-all results of the program to date show great promise for horizontal well in situ technology as a competitive source of bitumen from Alberta's vast oil sands deposits. The potential economics of a commercial expansion at the site are reviewed in this paper.IntroductionIn situ recovery o f bitumen from the Athabasca oil sands has puzzled the oil industry for many year s, but a breakthrough appears close at hand. The Underground Test Facility (UTF) project initiated by the Alberta Oil Sands Technology and Research Authority (AOSTRA) has had notable success in the piloting of horizontal well processes, which offer prospects for commercial development even under the highly competitive situation facing the Canadian industry . This paper describes the project briefly and presents the potential economics of commercial development on the UTF lease."

Jan 1, 1990

By Robert L. Akright

The Sumich (Victorine) gold mine is located in the Toiyabe Mountain Range on the east side of Victorine Canyon, a north-trending branch off Kingston Canyon in the northwest quarter of Section 27 and southwest quarter of Section 22, T16N, R43E, in the southern end of Lander County, Nevada (Fig. 1). HISTORY Discovered in 1862, the Victorine reached a peak of development between 1872 and 1887. The "Victorine" and "Morning Star" lode mining claims, located on the outcrop of a prominent auriferous quartz vein, were patented in 1869 and 1891, respectively. 1, respectively. Gold ore was mined underground in adits driven, on the level, directly into the side of the mountain. Ore brought to the surface was trammed about 457 m (1500 ft) south on a track constructed along the contour to ore bins. From this transfer point, the ore was moved by aerial tram to the bottom of the canyon then hauled by horse-drawn wagon to the mill located about 3.2 km (2 miles) east down Kingston Canyon. Exact details of the milling process used on the Victorine are lacking, but old reports mention water-driven stamp mills, amalgamation, chlorination, and cyanidation. Gold and silver mill products are reported to have been sent to England for final refining. High-grade gold values of 103 g/t (3 oz per ton) remaining in mine walls and on outcrops, attest to the lack of success in treating the Victorine ore in the early mills. The Victorine mine may have been worked sporadically after 1887 with little success. In 1934, control of the property was acquired by William P. Moloney, an attorney from Marion, OH, who also control- 1 led an interest in the successful Goldacres mine in Lander County, NV. This property was studied, sampled, and metallurgical tests were done in 1934, but no development resulted from this work.

Jan 1, 1990

By F. J. Susko

The U.S. Bureau of Mines is using Fourier-transform infrared (FT-IR) analysis to investigate the bonding mechanism which occurs during the dewatering of clay slurries. High molecular weight polymers are used as flocculating agents in these processes. This investigation presents the results of an FT-IR study of calcium-exchanged montmorillonite treated with polyacrylamide (PAM) and polyethylene oxide (PEO). Both thin film and attenuated total reflectance (ATR) spectroscopic techniques were employed to study this clay-polymer system~ Results suggest PAM is adsorbed to the clay via the nitrogen atom of the polymer. A water bridge is involved in the bonding between the clay and PE~. Evidence also suggests that PEO may be adsorbed directly onto the surface of the clay.

Jan 1, 1990

By Corbett G, Iwai N

The Japanese gold mining industry has a long and productive history and is presently undergoing a period of revitalisation encouraged by the Hishikari discovery. Deposits exhibiting the characteristics of epithermal mineralisation are very widely distributed throughout the island chain and an encouraging number of these are large, seven containing gold in excess of one million ounces. All the important deposits are quartz vein type and contain extremely high grade, or "bonanza". Zones.

Jan 1, 1990

By L. Lui, A. Cauchon, A. R. Laplante

"The gravity circuit at Les Mines Camchib Inc. consists of two pinched sluices to bleed a feed to one of two 76 cm (30"") Knelson concentrator. The Knelson concentrate is upgraded to smeltable grade with a smaller Knelson (18/30 cm) and a riffleless table. Their tails are column cyanided and washed prior to recycle to the grinding circuit. This paper details size-by-size circuit performance. The Knelsons recover around 90% of free gold (as determined by Mozley Laboratory Separator), even below 37 µm. The sluices are ineffective, with upgrading ratios around 2, but approaching unity in the fine sizes. Much of the effectiveness of the circuit lies in the high gold circulating loads in the grinding circuit, which partly atone for the poor sluice performance, and the ability of the Knelsons to recover free gold. Secondary upgrading recovers slightly above 99% of the primary concentrate gold, 90% of it in a 65% Au concentrate and the balance in a heavily loaded (10 to 20 oz/st) pregnant solution. INTRODUCTIONBackgroundThe operating performance of the mill of Les Mines Camchib Inc. has been described earlier (Laplante et al., 1989). The presence of significant chalcopyrite (1 % and up) makes flotation necessary prior to cyanidation, to limit cyanide consumption and minimize environmental impact. In 1982, the presence of very high gold circulating loads in the grinding circuit lead to the commissioning of a gravity circuit, schematically shown in Figure 1. Gravity recovery of gold has been found beneficial because it increases metallurgical recovery by 1-3% (Laplante et al, 1987), as only part of the flotation tail is cyanided, and economic recovery, because of the lower net smelter return of gold in the flotation concentrate (as compared with the gravity concentrate). The latter increase is estimated, with a net smelter return of 95%, at 1.5% when gold recovery by gravity is equal to 30%. In early 1988, a sampling program was initiated to characterize the behaviour of gold in the grinding/gravity circuit. This paper reports on the results of this study."

Jan 1, 1990

By G. J. Simandl, H. -L. Jacob, S. Paradis, G. Valiquette

"Nos travaux de terrain dans le Grenville, effectués dans le cadre d'un projet d'inventaire des gîtes de wollastonite, ont démontré qu'il existe un secteur exceptionnellement favorable à l’exploration pour la wollastonite. Ce secteur s'étend de la municipalité de Grenville jusqu'au pare du Mont-Tremblant (nord de St-Jovite). D'autres secteurs favorables a 'exploration pour la wollastonite ont été délimités dans les regions du Lac-Saint-Jean, de Shawinigan et de la Gatineau. Neuf categories litho-structurales de gites de wollastonite furent identifiées. L'importance d'un système ou vert pour la formation des gîtes de hautes teneurs fut établie. Un guide de prospection pour la wollastonite propre à la province tectonique de Grenville fut développé. Plusieurs des indices sont prometteurs et mériteraient des travaux de raise en valeur afin de determiner s'ils représentent une source de wollastonite exploitable à profit. Lac-Saint-Jean, Shawinigan and Gatineau areas. Deposits may be classified into nine categories depending on their relationship to intrusive rocks, discordant or concordant contacts with the host rocks, morphology, and major structural controls. Deposits consist mainly of wollastonite, calcite and clinopyroxene. They may contain one or several of the following minerals: feldspar, scapolite, quartz, titanite sulphides, zoisite, clinozoisite, garnet, idocrase and prehnite. Wollastonite content may reach over 70%. Some deposits are associated with graphite veins. Better understanding of the geology, combined with the proposed classification provides new exploration guide for wollastonite. Several deposits have grades of economic interest. Further work is needed to determine if any of these deposits can be exploited for profit."

Jan 1, 1990