Search Documents

By Alla D. Mah

Titanium forms several compounds with oxygen and also is able to dissolve interstitially about 33 atomic percent of oxygen. Starting with titanium dioxide, reduction becomes increasingly difficult as oxygen is removed; and the final step, be reduction of the titanium-oxygen interstitial solutions, is by far the most difficult. The possibility of reducing titanium oxide, or of purifying titanium containing oxygen, by treatment with certain more volatile metals has been a subject of considerable interest. Theoretical appraisal of the limitations of this possibility, however, has been hampered by lack of adequate information on the thermodynamic properties of the titanium-oxygen solutions. The purpose of the present work was to remedy this difficulty by expanding the thermodynamic knowledge regarding these solutions. The experimental work involved three types of calorimetry and furnished the following information: (1) Heats of formation of 11 titanium-oxygen solutions, in the range of 0 to 10 wt.-percent oxygen, were determined at 298.15° K. As a byproduct, an improved value of the heat of formation of rutile was obtained, which, in turn, led to improved values of the heats of formation of the lower titanium-oxygen compounds. (2) Low-temperature heat-capacity data and entropies at 298.15°K in were determined for 2 representative titanium-oxygen interstitial solutions. (3) High-temperature heat-content data were obtained for 2 titanium-oxygen interstitial solutions to about 1,600° K.

Jan 1, 1957

By Herty, C. H.

No attempt will be made here to review the previous work done by investigators on the general subject of inclusions, because it was discussed sufficiently in an early cooperative bulletin of this series (No. 36, 1928), and reference was then made to general bibliographies. The work described in this present bulletin deals directly with the study of the mechanism of deoxidation of steel with aluminum and the formation of inclusions containing alumina. Unquestion- ably, such inclusions are encountered in most steel-making practices and little has been done to determine their characteristics. Aluminum is used to ensure rapid deoxidation during the solidification stages of the steel. For this reason the possibilities of inclusion elimination are slight and alumina-containing particles will undoubtedly be present in the ingot. Besides this common practice, aluminum is often used in the ladle with other deoxidizing agents such as silicon and manganese. Ladle additions of aluminum are made to rimming steels to obtain the correct partial deoxidation desired in this type of steel. In killed steels the aluminum is added to ensure soundness, as far as blowholes are concerned, in the ingot. In either rimmed or killed steels, alumina or alumina-containing inclusions are found therein, the amount and type depending on the oxidation of the metal, the amount of aluminum added, and the addition of other deoxidizers.

Jan 1, 1957

The first metal-mine accident-prevention course was prepared and published in 1942--45 as a series of seven miners' circulars (Nos. 51-57). The scope of the course has been broadened, revised, and brought up to date, and it is being published as a similar series of seven miners' Circulars (Nos. 51-57, revised) on accident prevention in metal and nonmetallic mines. These circulars are: Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the uses of investigations and reports of all accidents.

Jan 1, 1957

By H. N. Dunning

A comprehensive production research program, now in progress at the Petroleum Experiment Station of the Bureau of Mines at Bartlesville, Okla., includes studies of the displacement of petroleum from sand by detergent solutions. An earlier report (12)2/ presented the results of an extensive research program to determine the value of detergents as floodwater additives. This report presents later results of the detergent-testing program (13, 17). Although water-flooding methods and controls are constantly being improved to increase the production of oil from secondary-recovery operations, considerable crude oil commonly remains.in place after a water flood has been terminated. Therefore, the possibility of improving the efficiency of a waterflood by the use of detergents is of increasing interest. The effects of many substances on the efficiency of water flooding have been investigated in laboratory studies (5, 11, 13, 17, 19, 24). Of the various sub-stances tested, only surface-active agents were consistently effective in removing oil from sand. Results of laboratory studies presented in earlier reports (9, 11, 12, 13) show that many detergent solutions effectively displace petroleum from sand surfaces under varying conditions encountered in centrifuging, manual and mechanical agitation, ultrasonic vibration, and imbibition.

Jan 1, 1957

By F. D. Everett

The exploration work on a seleniferous tuff deposit near Lysite, Wyo., was confined chiefly to an area of approximately 1 square mile selected on the basis of prior examination and sampling work by the Bureau of Mines. This area was superficially explored by digging and sampling over 2,000 feet of trenches and 15 test pits. The surface sampling indicated that the deposit might contain a multimillion-ton reserve of easy-to-mine volcanic tuff assaying more than 0.01 percent Se. Later, 11 holes, ranging in depth from 57 to 135 feet and totaling 929.4 feet, were drilled under contract using a dry rotary drill. Samples for assay were cut at 5-foot intervals or at noticeable physical changes in the formation being drilled. Of the 206 samples assayed from the drilling, only 8 contained more than 0.005 percent selenium, and 2 of these assayed as high as 0.012 percent Se. Chemical analyses of samples obtained from six holes drilled by the Nugget Coal & Timber Co. to the south of the area explored by the Bureau of Mines showed that no selenium-bearing formations were encountered in that work. Two of 72 samples taken from 42 validation pits dug by claim holders contained more than 0.005 percent selenium. The exploratory work established that the selenium mineralization is erratically distributed in small irregular bodies and is not confined to any one tuff bed. Because of the lack of correlation between the infrequent showing of low-grade tuff, neither the extent nor grade of the reserves could be calculated.

Jan 1, 1957

By R. C. A. Thurston

AT A FATIGUE SESSION organised by the A.S.T.M. in 1949, R. E. Peterson presented a brief introductory paper ( 1) in which lie referred to a discussion on the fatigue of metals which took place in England in 1849, and then proceeded to review some of the subsequent researches concerning the mechanism of fatigue. In the course of the review, he discussed metallograpl1ic studies with single crystals and polycrystalline materials, studies with X-ray methods, and the application of the electron microscope. During that hundred-year period considerable progress was made toward a better under-standing of the nature of fatigue, although it is probable that even greater attention was directed to the more practical aspects of the problem, such as the effects of notches, temperature, corrosion, surface treatment, residual stresses, and so on. Since then there has been an appreciable acceleration in the tempo of the fundamental work, partly influenced by the rapid development of the theory of dislocations, with the result that our knowledge of the mechanism of slip, the initiation of fatigue cracks, and their subsequent propagation, has still further advanced, although it is by no means complete as yet. The present paper is an attempt to out-line the more recent developments in these basic studies, to correlate them when possible, and to draw attention to those directions in which research might profitably be pursued.

Jan 1, 1957

By S. H. Ash

Diesel locomotives, trucks, bulldozers, and other diesel-powered equipment are fast proving their superiority for mine transportation purposes. MORE than 100 minerals are mined and processed in the U. S. Management and labor have negotiated wage-scale agreements that have balanced wages and affected cost of labor in such a manner that comparisons can be made of transportation costs. Transportation of materials underground has become of vital importance.1"0 This report describes underground haulage methods and equipment, presents cost analyses, and discusses future plans for underground transportation in metal mines. It does not cover hoisting in shafts or slopes by cage, skip, or cars. Advancements have been made by the metal mining industry in lowering transportation costs in several mines, making it possible to mine orebodies or portions of orebodies not considered economically recoverable a few years ago.7,8 Wumerous reports have been written on transportation at metal mines; this report covers recent haulage at some representative mines throughout the U. S. The term metal mine is used to include all noncoal mines from which up-to-date information was obtainable. The best haulage equipment is subject to break- downs and accidents; but unless the rolling equipment, track, and signal systems are kept in good repair and are operated systematically, these breakdowns and accidents are likely to be frequent, destructive, and more costly than are necessary.10 Rail haulage crews using dependable rolling stock can move trips safely over grades low enough to be traveled without loss of control; this applies particularly if the track is straight and well maintained. Few accidents occur on main haulage lines if visibility and clearance are good and clear track is assured. One-way traffic underground is a recent development contributing to reduction of accidents and increased efficiency in mine haulage (Kelly mine, Anaconda Co., Butte, Mont., and Climax mine, Climax Molybdenum Co., Climax, Colo.)." Locomotives: Six types of mine locomotive used in recent years are trolley, storage battery, combination trolley and storage battery, diesel, compressed air, and gasoline. Electric haulage has been displaced by compressed air locomotives, which have been used successfully in certain instances, especially on dirty and wet tracks and steep grades." Maintenance cost is high, and operating efficiency, from a power standpoint, is low. Compressed air locomotives operate under self-contained power, and the absence of bare elec-

Jan 1, 1957

By P. M. Gruzensky

In view of some of the outstanding properties of chromium, considerable effort has been made in recent years to prepare the high-purity metal in ductile form. The object of this investigation was to obtain such metal by electrolysis of chromic acid solutions and to determine the conditions that yield optimum results. The apparatus is described, as well as the parameters that received consideration. Ion-exchange resins were employed to remove cation impurities from the electrolyte. Tensile specimens prepared from the electrodeposits by arc melting, press forging, swaging, and drawing, were ductile at room temperature. INTRODUCTION Metallic chromium displays an exceptionally high resistance to corrosion, oxidation, and wear at elevated temperatures. Although these properties are utilized to some extent when chromium is alloyed with other metals, such as in stainless steels, high-chromium alloys and pure chromium are not employed as engineering materials because of a serious lack of ductility and impact resistance at room temperature. Because high-chromium alloys appear promising as refractory metals for applications such as in gas turbines, much interest has been shown recently in the preparation of uniformly ductile chromium and in determining which factors contribute to its brittleness.

Jan 1, 1957

By E. A. Magill

The Bureau of Mines has begun a study of the copper resources of the Cascade Mountains of Washington. The program includes reconnaissance of mineralized areas and examination and occasionally limited exploration of deposits that are considered characteristic of an area. The Bureau of Mines believes that published information may assist industry in searching for new sources of copper. The Miners Queen is one of a few Cascade Mountain deposits selected for prelim¬inary exploration. The investigation was not planned to delineate the ore body. A diamond-drilling program was carried out at the Miners Queen mine in the summer of 1955. Five diamond-drill holes were completed, totaling 628 feet. Two 35-foot shafts were dewatered, and all accessible underground and surface workings were examined.

Jan 1, 1957

By Carl E. Johnson

INTRODUCTION A method for predicting water-flood oil recovery was reported by H. Dykstra and R. L. Parsons' in 1950. It is now generally known as the Dykstra-Parsons method and is widely used by petroleum engineers. The method is semiempirical and consists of a correlation of four fundamental variables. These are: V, vertical permeability variation;' a, mobility ratio; Sw initial water saturation; and R, fractional recovery of oil in place at a given producing water-oil ratio. The correlation extends over a wide range in each of these variables, and may be applied to all formations with initial oil saturations of 45 per cent or greater. The method of calculation originally outlined by Dyhtra and Parsons closely follows their derivation. And this is a convenient way of illustrating the development of some rather complicated ideas. However, in actual use it is more cumbersome than necessary. The purpose of this note, therefore, is to provide a simplified method for making Dykstra-Parsons predictions. A SIMPLIFIED GRAPHICAL SOLUTION The correlation between V, a, Sw and R, corresponding to a given producing water-oil ratio, can be shown on a single graph. This is best done by plotting V against a to show lines of constant R(1 - S, . WOR-0.2). Figs. 1, 2, 3, and 4 show these plots

Jan 1, 1957

By Wilbur A. Haley

One of the purposes of the investigation was to determine and report on how coal augers are used to mine bituminous coal that is near outcrops and may not be mined otherwise by any other present-day method. Such increased overall recovery results in the conservation of coal resources. Other reasons for the investigation were to determine and report the production rates of such operations and the types of equipment used. Auger mining of coal as a means of coal recovery supplementary to strip mining has been introduced and developed since World War II. This type of coal mining has grown rapidly, and bituminous-coal production by auger mining has been estimated at 6,000,000 tons in 1955. Mines were selected for study to give reasonably representative information on auger mining in different types and thicknesses of coal beds in different geographic areas and on different types and sizes of equipment operated under various conditions. This report is based on field studies of 8 auger-miming operations in Pennsylvania, West Virginia, and Ohio and in 5 different coal beds. Operations were observed in active strip mines, in strip mines reopened for auger mining, and along benched coal-bed outcrops. At the time of this study, no augers were reported to be operating in underground mines. The diameters of holes drilled ranged from 26 to 52 inches, and the lengths of holes ranged up to 208 feet. At some operations auger holes often penetrated abandoned underground mine workings.

Jan 1, 1957

By J. B. Rosenbaum

This report presents new findings and consolidates previously published data to provide a single reference containing a concise and comprehensive description of the Bureau's work on electrolytic chromium. Two separate systems for electrolytic-chromium recovery were developed, one designated as the oxidized system the other as the reduced system. The electrowinning of chromium metal follows the dissolution of chromium from the ore or from ferrochrome and its separation from gangue and metallic impurities. Chromite was first solubilized by pressure digestion at slightly elevated temperatures in an oxidized acid solution using Na2Cr2O7 as an oxidizing agent. Later it was found that a sodium-free electrolyte was preferable, using return-cell anolyte containing H2SO4 and Cr03 as the oxidizing agent. Gangue materials were separated from the soluble metallics by filtration; and, after the Cr+3 had been stabilized, the metallic impurities were separated as crystalline ammonium salts by vacuum crystallization.

Jan 1, 1957

By Oren C. Baptist

[Several new oilfields have been developed in northwestern Wyoming during the past 10 years, production is obtained from discontinuous, permeable sands enclosed within impermeable shales. The energy to drive the oil to producing wells in supplied by gas in solution in the oil. Most of the wells had high-initial potentials, but rates of oil production have steadily declined, indicating a dissipation of the driving energy and the possibility that large volumes of oil will remain unrecovered in the reservoirs. The studies reported in this paper were undertaken to develop laboratory data of the type most likely to be needed by persons studying the susceptibility of the Newcastle sand reservoir to secondary-recovery methods.]

Jan 1, 1957

By F. L. Wideman

This paper lists resources of sulfur in Wyoming, Colorado, Utah, New Mexico, and Arizons, an area comprising approximately 522,600 square miles, Sources of sulfur occuring within the region are sulfur are, pyrite and pyritic ores, and natural gases and petroleum. Data concerning these sources are presented on a statewide basis. Some of the known deposits of sulfur ore are surficial and of fumerole origin; other deposits have resulted from oxidation of pyrite or sulfide ores of copper, lead, and zinc. The deposits are small and the sulfur is distributed erratically in them. There is a small production from some of the deposits, and the material produced is used as soil conditioner.

Jan 1, 1957

By Keats, J. L.

IN THE literature on the elimination of metalloids in basic open-hearth practice, there are a great many heats recorded in which excellent data on changes in slag and metal composition during refining are given, but in almost all of these heats either temperature data or weights and analysis of charge are unrecorded and observations on the physical charac- teristics of the slag are almost always lacking. With these points in mind, a test heat was made in which as complete as data possible on all the factors that affect the elimination of metalloids were obtained.

Jan 1, 1957

By R. R. May

A preliminary examination of the Houston strip-coal mine, situated on the Alaska Railroad at milepost 175 (61 rail miles north of Anchorage, Alaska) and a review of all available information resulting from early coal exploration activities in the area resulted in plans to investigate the coal-bearing formations at depth by means of diamond core drilling to indicate the existence of additional reserves of coal in close proximity to railroad transportation, where it would be quickly available to meet rapidly expanding military and civilian fuel requirements. From the date of mobilization of equipment, August 28, 1951, until date of suspension, August 18, 1952, 2,010 feet of diamond drilling was completed. Ten definable coal beds were cut, of which 2 appear to be persistent and minable over an area of approximately 1/2 square mile. Within this area the 2 minable beds contain approximately 5,000,000 tons of coal in place. Of the remaining beds, at least two others may be minable to the eastward near their projected outcrops; however, these and deeper beds (at least in the vicinity of the drill holes) lie beneath a zone of pressurized gas and brackish water. From a practical standpoint, continued development and utilization of the coal in this vicinity will depend on the operators' ingenuity in developing cheap mining methods and on diligent prospecting for strippable coal under the comparatively light glacial cover.

Jan 1, 1957

By L. J. Kane

While analyzing synthesis gas produced from coal, the Bureau of Mines found that conventional procedures for naphthalene determination were difficult and time consuming. The Bureau developed a rapid and sensitive turbidimetric procedure, which requires only simple instruments and hence can be used in plant-control laboratories. The gas is passed through a saturated aqueous solution of picric acid at 3° to 4° C. whose turbidity is then measured at room temperature. A dispersing agent is added to prevent coagulation of the suspension on warming. Only about 1 mg. (0.015 grain) of naphthalene need be absorbed, and precision and sensitivity are a few ten-thousandths of a grain, or a few hundredths of a grain per 100 cubic feet. The determination can be completed less than 10 minutes after absorption. INTRODUCTION One of the functions of the Branch of Coal Gasification, Bureau of Mines, Morgantown, W. Va., is to develop economical methods for manufacturing, from coal, a mixture of hydrogen and carbon monoxide for producing hydrogen, methane, and other gaseous fuels. This raw gas may contain many impurities, including naphthalene. This impurity is usually determined by first forming naphthalene picrate in a water solution of picric acid, separating the picrate, and titrating the unreacted picric acid or the picrate itself.

Jan 1, 1957

By Herty, C. H.

Three distinct processes take place during the conversion of iron ore to steel. First: the raw ore is reduced to metallic iron in the blast furnace and during this reduction certain constituents are dissolved in the iron, either through the solution of a solid into a liquid phase, as in the case of carbon, or by reduction of an oxide existing in the slag to the metallic element of that oxide, with subsequent solution of the metallic element in the iron. Thus by the process of solution and reduction, a pig iron results which contains about 4 per cent carbon, 1 per cent silicon, 1 to 2 per cent manganese, 0.1 to 0.4 per cent phosphorus, and 0.03 to 0.10 per cent sulfur. To obtain a sufficient yield of iron from the ore it is necessary that the reducing process be carried as far as possible, with the result that the impurities mentioned accompany the reduced iron. Second: to convert this iron into steel it is necessary to oxidize a part of the iron in eliminating the impurities to the extent desired for the particular product being made. In eliminating these impurities by oxidation a certain amount of iron oxide (FeO) dissolves in the steel. This dissolved FeO reacts with the metalloids, except sulfur, and to eliminate them to the desired extent it is necessary to leave a considerable amount of FeO in the metal. The reaction of iron oxide with silicon, manganese, and phosphorus results in the formation of the oxides of these elements. The oxides enter the slag and the extent of elimination of the elements depends on certain equilibria between the slag and the metal. The reaction of FeO with carbon results in the formation of the gases CO and CO, which, after saturating the metal, pass into the furnace gases. Third: after the iron has been purified to the desired extent as far as the elements listed are concerned, it is necessary to deoxidize the bath to remove the FeO, which is the vital factor in gas formation as the steel solidifies.

Jan 1, 1957

By B. C. Mariacher

EXTRACTION of uranium from ores is being ac-complished by processes which. for the most part, subject the entire ore to acid or carbonate leaching. Ore deposits with a U 3 O 8 content below 0.10 pct U 3 O 8 are seldom considered suitable for treatment by leaching. A preliminary concentration that would enrich the uranium content of an ore by a simple, low cost process based on physical properties of the ore might result in some low grade deposits becoming commercial ores. In addition, the process might be employed in existing operations to reduce transportation and leaching costs and to increase capacity of existing leaching plants. A study to attempt the development of a preliminary concentration process for primary uranium ores was undertaken by the Colorado School of Mines Research Foundation under sponsorship of the U.S. Atomic Energy Commission. The objective of this work was to produce concentrates containing 0.25 pct U3O8 from the low grade ores tested. Ores Tested: The main effort was devoted to the low grade primary uranium ores from northwestern Saskatchewan. Samples were obtained from the Beaverlodge operation of the Eldorado Mining & Refining Ltd. Additional primary ores, obtained from deposits in Gilpin County, Colo., contained from 0.07 to 0.10 pct U3O8. Summary of Concentration Tests: The Beaverlodge ore was tested to determine amenability of the ore to concentration by magnetic, electrostatic, gravity, and scrubbing processes. None of these produced satisfactory results. Both gravity and magnetic processes produced fairly good concentrates when closely sized fractions of the ore were treated, but on the basis of treating the total ore, recovery was poor. Preparation of sized fractions and the low capacity of equipment for suitable concentration made these methods impractical. As flotation offered the advantage of treating the total ore without intermediate sizing, the main effort was in this direction. A flotation process was developed that fulfilled the concentration objectives as set by the AEC. Pilot plant testing was used to verify results obtained from laboratory batch testing. Mineralogy: A petrographic examination of the Beaverlodge ore included a study of polished sur- faces and identification of the radioactive mineral by autoradiograph and X-ray diffraction. Approximate quantitative mineral identification was as follows: quartz, 60 pct; orthoclase feldspar, 20 pct; chlorite, 10 pct; carbonates, 5 pct; and miscellaneous minerals, 5 pct. Included in this last group were plagioclase feldspar, pyrite, mica, chalcopyrite, pyroxene, sericite, magnetite, galena, and uraninite. The most general occurrence of uraninite was in the form of crusts and thin coatings on limonite-stained grains of pyrite, quartz, and pyrite-quartz intergrowth. At least 90 pct of the uraninite was still attached to other minerals in a 100 by 200-mesh size fraction. The uraninite crusts were as small as 10 to 20 µ diam, and 5 to 10 µ thick. The Flotation Process Petrographic examinations of the Beaverlodge ore had indicated the impracticability of attempting to concentrate the uranium by floating individual grains of uraninite. Liberation of the uraninite required grinding to sizes below those suitable for flotation. However, there was preferential association of the uraninite with some minerals while others were free of uraninite attachment. The approach to the development of a flotation process was, therefore, based upon an attempt to concentrate the uraninite by floating carrier minerals. The following paragraphs discuss the various stages of the process with regard to the factors tested and the conditions under which best results were obtained. Grinding: The most effective size range for flotation was —150 mesh + 13 µ. The —13 µ material in the final concentrate had a higher U3O8 content than the total ore, but not as high as the average concentrate; however, rejection of slimes before flotation was prohibitive because of the loss in uranium carried in the —13 µ fraction. Grinding techniques which contributed to a minimum production of fines, such as stage grinding, were then employed. Quartz and Silicate Depression: These minerals represented approximately 80 pct of the ore and were free to a large degree of uraninite attachment. Significant improvement in the grade of the concentrate was obtained by depression of these minerals with hydrofluoric acid or sodium fluoride. Promoter: Selective stage flotation of uraninite carrier minerals was simplified by development of a single promoter mixture. The mixture consisted of an emulsion of a fatty acid, fuel oil, and a petroleum sulfonate and was selected after a comprehensive series of tests. It contained three parts by weight of an oleic and linoleic acid such as Emersol 300,

Jan 1, 1957

By J. C. Holm

ALTHOUGH the main constituents of Portland cement are the oxides of calcium, silicon, aluminum, and iron, characteristics of the cement are seriously affected by such contaminants in the raw materials as magnesium, phosphorus, sodium, potassium, sulfur, and others of lesser importance. Sources of cement raw materials comprise a long list of minerals occurring in nature in various degrees of purity. The calcareous raw materials are generally limestone of purity varying from calcite to cement rock (a low-grade limestone of natural, almost correct chemical composition), chalk, marl, seashells, coral, and coral sand. The argillaceous raw materials supplying silicon, aluminum, and iron are mainly various forms of clay and shale, to which may be added silicious sand, iron ore, bauxite, or kaolin for minor adjustment of the chemical composition. The quality of Portland cement in this country, as in most parts of the world, is controlled by rigid specifications limiting both its chemical and physical characteristics, and cement manufacturers must comply with these specifications to market their products. Brandon Raw Materials: An unusual deposit of marl, limestone, and clay occurs 12 miles east of Jackson, Miss., near the village of Brandon. The deposit is of sedimentary origin and of relatively young geological age. Layers of marl vary from putty-like consistency to such hardness that it can be cut with a knife. Interspersed between the layers of marl are bands of limestone varying from very soft to hard. the compressive strength of the hardest layers exceeding 15,000 lb per sq in. The layers of marl range in thickness from a few inches to about 25 ft. The limestone bands seldom exceed 2 to 3 ft but often occur in thinner veins in the quarry face. Above the top layer of the deposit, which may be marl or limestone, a layer of clay ranges in thickness from a few inches to more than 20 ft. Part of this clay is harvested with the raw material to supply part of the argillaceous components, but most of it is stripped as overburden and wasted. A highly silicious clay of extreme fineness, harvested from the bottom of the quarry below the marl and limestone bands, is to correct the silica content. Fig. 1 shows typical examples of the interrelation of the various materials, based on drill logs obtained during exploration of the deposit. The marls vary in moisture content in the bank from 15 to 30 pct and contain up to 70 pct -200 mesh particles and up to 40 pct —10 p particles. A large percentage of the fine fraction is within the colloidal range, making the marl extremely sticky. The limestone beds range in hardness from that of the hardest marl to a medium hard limestone and in moisture content from 2 pct to approximately 14 pct. The line of demarcation is often difficult to draw and the moisture content is possibly the best means of classification. The ratio of soft to hard material is not constant throughout the deposit, but the average is approximately 70 pct soft to 30 pct hard material. Through the years this deposit had been repeatedly explored by cement companies and rejected as unsuitable for cement manufacture, mainly because of physical characteristics. In 1950, after careful exploration of the deposit and comprehensive laboratory and pilot plant tests of the raw materials, officials of Marquette Cement Mfg. Co. of Chicago were convinced that a practical and economical method of processing the raw materials had been devised and authorized construction of a new plant that began production in December 1951. Marl and limestone, common raw materials for Portland cement, usually occur in such a manner that they can be worked separately. Their harvesting and processing normally have presented no difficult problems, as standard equipment and methods are available for handling either sticky or hard materials. No other cement plant utilizes a deposit of the nature of that at Brandon, however, and for this reason no prior art was available for design. When properly blended, the raw materials produced an excellent cement without additives. Basic problems to be solved in designing the cement plant were:

Jan 1, 1957