Search Documents

By L. D. Schmidt, W. C. Schroeder, A. C. Fieldner

"INTRODUCTION The highly mechanized character of modern warfare makes steel the most vital raw material. The shortage of steel scrap in the United States is forcing the use of increased quantities of pig iron in steel manufacture, so that the rate of pig-iron output will continue to be the controlling factor in steel production. 5/ At the same time, the construction of new blast furnaces is limited both by time and the amount of strategic material available. Under such circumstances, every effort must be made to attain and then maintain maximum pig-iron output from the equipment now in use.When forcing a blast furnace to the ultimate in production the highest standards for quality and uniformity of the coke must be maintained. In view of these facts, the Bureau of Mines, in cooperation with the Office of the Solid Fuels Coordinator for War, is surveying the coke industry to study the various steps in producing coke of higher quality and greater uniformity. 6/ The engineers conducting the survey are visiting key men in coke-oven and blast-furnace organizations to determine, first, the major and most common problems in coke production and use; and, second, the best and quickest method for solving them. Various operators have made good progress in solving individual problems, and a Nation-wide exchange of information among them will make possible widespread adoption of the best practices. It is the purpose, of the survey and reports such as this preliminary one to facilitate such exchange of information. As an outgrowth of the survey, it was soon revealed that many operators could be helped by cooperation with various Government agencies, particularly to procure suitable coals, minor additions to equipment facilities, and tests on certain properties of coal or coke, or specific advice concerning the operation of various types of equipment. The machinery and organization necessary for securing this cooperation have been set up as a part of this work."

May 1, 1943

By Glan Dale Coe, Will H. Coghill

"INTRODUCTION Characteristics of the mineral products that are to be contrasted herein are net energy consumed in grinding to a definite top limiting size and size distribution of the ground products. Through contrasts of these grinding characteristics this paper to differences in related mineral products and in unlike products. For,example, in anticipation of the data to follow, although Joplin chert and Babeitt taconits are running mates in defying the best crushing machinery, taconite is one of the more docile and Joplin chert one of the most refractory mineral products ordinarily fed to a grinding Routine grinding tests on a great variety of ores and tabulation of the findings have been covered amply by Lennox 4/ and by Maxon 5/ and associates. In contrast to that work, the present paper is a record of random tests made over a long period, and each answered an urgent question at the moment. The work was done at the Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama. The pressure of war work prevented an organized investigation."

Apr 1, 1943

By Kenneth G. Skinner, Hewitt Wilson, Thomas L. Hurst

Although chromite deposits occur in California , Oregon, Washington, Montana, Wyoming , Pennsylvania, Maryland , New Mexico , North Carolina, Alaska, and the Phillippine Islands , less than 1 percent of the ore used in the United States is obtained from these deposits . Most of the ore in peacetime has been supplied by imports from South Africa, New Caledonia, Turkey, and Cuba . The mineral chromite , the most important chromium ore , is an isometric spinel with an ideal composition of FeO Cr2O3 , but commercial chromite has the variable composition (Fe , Mg) Oʻ (Cr , Al , Fe) 203. Chromite has a black color , a specific gravity of 4.4 , and a hardness of 5.5 . In thin section the color is reddish -brown to black . Chromite occurs in dunite and pyroxenitic ultrabasic rocks , which are composed of iron- magnesium silicate minerals such as olivine , saxonite , serpentine , and enstatite . These are also the gangue minerals . Com mercial ore occurs at random in the country rock in kidney- or lens - shaped deposits , which have no apparent relationship to each other . Stringers , veins , and bands often cut the country rock without regard either to fracture or to other deposits . Some beach sands , such as those in southern Oregon, contain chromite .

Mar 1, 1943

By Albert G. Zima

THE conservation of strategic materials during war rime gives rise to many problems not commonly encountered in times of peace. During normal times, when world trade is unrestricted, we are apt to become lavish to a point of extravagance in our use of those materials which, during rime of war, become scarce owing to inadequate transportation and production facilities or because the enemy may be in position to control sources of supply. It becomes necessary, then, to enforce rationing of available sup-plies, and in some cases, where such supplies are wholly inadequate, we find we must resort to the use of substitute materials. We are now confronted with such a problem to an extent never before experienced, with the result that many of the commodities upon which our civilization depended are now either shut off completely or, because of the heavy demand occasioned by war production, are not available in sufficient quantities to meet requirements predicated on peace-time standards and manufacturing methods. It has become necessary, therefore, to make many changes, some of them very drastic indeed, to enable us to carry on our war effort effectively. This? discussion will deal briefly with one phase of this problem, namely, the conservation of alloys required in the making of steels necessary for war production. In line with a request from the War Production Board, the Technical Committee on Alloy Steels of the American Iron and Steel Institute made a study of experimental steels embodying the !east amount of alloying constituents, with the objective in mind of substituting these steels wherever possible for the standard alloy steels used heretofore. This study embraced the following phases: (1) The availability of silicon and manganese; (2) The average quantity of alloying elements recoverable from scrap; (3) The effect of increases in manganese and silicon contents on the general properties of steel; ( 4) The elements and ranges of elements which might be used to duplicate the hardenability of the steels now in use; (5) The effect of combining several elements in small quantities upon the properties of steel at various hardness and strength levels; (6) A determination as to whether or not the steels selected would suffice for general application. Working on this basis, the Committee arranged for the manufacture of several heats of steels containing various combinations of different amounts of such elements as silicon, manganese, chromium, nickel, and molybdenum. The steels thus produced were compared by hardenability tests.

Jan 1, 1943

By W. T. Reid

A shortage of anthracite for home heating indicates the necessity of using other fuels for this purpose; low-volatile bituminous, or "soft" coal is the most feasible supplementary fuel, either burned alone or when mixed with anthracite. Comparison of Bituminous Coal and Anthracite Whereas anthracite is clean, burns without smoke, and requires little attention, bituminous coal is dusty, tends to burn with a smoky flame, and forms coke in the fire pot that must be broken up to maintain a continuous high output of heat. When properly fired, however, bituminous coal responds more quickly than anthracite to changes in damper settings and consequently can supply more heat in a short time. It is generally less expensive and usually contains less ash than anthracite.

Jan 1, 1943

By C. W. Wark, Fred Wise

The Getchell mine, a comparatively recent gold discovery, is in the old Potosi mining district, Humboldt County, Nevada. All ore is mined from open pits using Diesel shovels and gasoline trucks. Two types of ore are mined, oxide and sulphide. Oxide ores are siliceous or shaly; sulphide ores either gougy, siliceous or shaly. In mining, the sulphide ore is segregated into hard and gougy ore, because the gouge must be dried before it can be crushed. The oxide ore is not segregated. General Metallurgy The oxide ore is the leached outcrop that overlies the sulphide ore body. All of the iron and arsenic sulphides found in the sulphide ores have been thoroughly oxidized. The sulphur and arsenic have been leached out while the iron is present as hematite and limonite. The oxide ore is amenable to direct cyanidation, and although no visible free gold is present it is released at a comparatively coarse grind. The sulphide ore is more refractory, since the gold is all of micron size and some of it is locked in fine sulphides. It has been established microscopically that the free gold is coated with an impervious shell, which is probably some form of iron compound. The sulphide ores contain from 1.5 to 2 per cent of arsenic, which is present as orpiment and realgar with minor amounts of arsenopyrite. The orpiment and realgar are of a later mineralization than the gold and are barren. Roasting and washing of the sulphide ore prior to cyanidation is necessary to eliminate , the arsenic, to alter the gold coating from an insoluble form to a soluble form, and to release the gold associated with the fine sulphides. Washing the ground calcine in weak sulphuric acid, trona, or hot water are beneficial in the order named, but to date the water is the best from an economic standpoint. Metallurgical tests as well as plant practice indicate that a certain amount of gold cannot be recovered even by going beyond economic practices. On this basis metallurgical results are viewed in the light of an optimum tailing rather than a percentage of extraction. Milling Practice Crushing (Fig. I).—There are three primary ore bins, one each for oxide ore, gougy sulphide ore, and hard sulphide ore. In front of each bin a substantial yard is maintained, which makes it possible to Stockpile 2500 tons of oxidized ore, 1000 tons of hard sulphide ore, and 1000 tons of gougy sulphide ore. The bins are fed by a 60-hp. caterpillar bulldozer from the stockpiles. Fig. I shows the method and

Jan 1, 1943

By John L. Boardman

Because of the attention that has recently been given to the health and safety of miners by various organizations such as the A.I.M.E., The American Congress, Mining Section, National Safety Council, as well as the Bureau of Mines and various state mining departments, your committee on health and safety deemed it best to call attention this year to the mine-accident cause that is by far the most important; namely, injuries due to falls of ground, rock, roof and coal. Each of several members of the committee contributed a brief outline of the importance of this accident cause in his district. While these papers were brief, it would require too much time and space to give them in full, therefore we present an outline of each and summation of all. Report of M. D. Cooper, Hillman Coal and Coke Co. M. D. Cooper, Division superintendent, Hillman Coal and Coke Co., Pittsburgh, Pa., contributed the following: During the period from 1930 to 1939, accidents from falls of roof in bituminous mines average 54.3 per cent of all accidents. In mechanized mining, there is a tendency toward reduction in this class of accidents because the operator of the machine is usually at a distance of 10 to 20 ft. from the face, whereas in hand load- ing the miner is close to the face during most of the shift. No doubt the use of aluminum and light steel beams supported at regular intervals by jacks, a common practice in mechanical mining, has contributed to the favorable record so far developed. Report of M. H. Fies, De Bardeleben Coal Corporation Milton H. Fies, Vice-President, DeBar-deleben Coal Corporation, Birmingham, Ala., says: With reference to the types of mining, it is suggested that a clear understanding be had as to the character and thickness of the directly overlying strata, with especial consideration to the strength and in some cases an analysis of it. In coal mining, generally speaking, overlying strata higher in silica than others is stronger. In changing from narrow to wide places, the procedure should be experimental, both as to the width and depth of places and as to the nature of the necessary timbering. Since most of the accidents in coal mining particularly are due to falls of roof and coal, this phase of mining should be attacked with vigor There is no substitute for discipline and, in this connection, under present conditions it is important that cooperation by the labor ornanizations- be sought and that a spirit of fairness prevail. Frequent and thorough inspection of all active working places should be made.

Jan 1, 1943

By Arthur F. Taggart

This paper proposes two units (believed to be new) for designating, respectively, capacity and efficiency for primary and intermediate crushers. Capacity Operators know that the tonnage of rock that can be put through a particular crusher in a given time depends primarily upon the crusher setting (open setting for jaw and primary gyratory types; closed setting for cones and rolls), and secondarily on the lithological character of the feed, its maximum size, the amount of fines that it carries, its moisture content, and the method of feeding. The proposed capacity formula states a relationship between all of these factors in one empirical equation, as follows: Tr = TR80K'K" [I] in which Tr, called "reduction tons per hour" is the new capacity unit; T = tons of feed per hour requiring crushing; R80 = "80-per cent reduction ratio"; and K, K', and K" are constants that approximate quantitatively lithological character, moisture content and method of feeding, respectively. T is the hourly weight of material in the feed that is coarser than the coarsest discharge of the crusher. (For marked departures from the normal specific-gravity range—2.5 to 2.7—T should be adjusted to corresponding volumes.) In the crushers under consideration, discharge from the crushing zone is limited by the minimum dimension of a particle. Passage of the particle through a square-mesh screen is limited by its intermediate dimension. Sheppardl has shown that the ratio of maximum: intermediate: minimum average dimensions of broken rock fragments may be taken as about 1.5:=:0,6 for nonslabby rocks such as are normally crushed, while for slabby rocks, such as thin-bedded sedimentaries, foliated schists and gneisses, and the blocky metamorphics, the ratio is of the average order I.3:I:o.3, with the possibility of an even smaller relative value for the thickness. Gaudin2 finds the corresponding ratio for —I50 + 200-mesh pyrite to be I.4: I:0.6. The hourly tonnage of crusher-plant feed, therefore, should be diminished by the amount thereof that would pass a square-mesh screen of which the aperture is S times the crusher setting, where S is a shape factor with the value 1.7 for rocks that break exceptionally cubic; 2 for ores and rocks that exhibit no appreciabie tendency to slabbiness; and 2.5 to 3, or, in exceptional cases, even larger, when the tendency to slabbiness is marked. R80 is the quotient of the theoretical square-mesh aperture that would pass 80 per cent of the feed, divided by the aperture that would pass 80 per cent of the product. It is best determined from screen tests. If, as is usual with primary crushers, a sizing test of feed is not available, the

Jan 1, 1943

By E.G. Lewis, l.M. Barker

The literature of milling is replete with papers devoted to the subject of ball milling, all of which no doubt have contributed in one way or another to progress in that art. In this paper reference will be made to only a few of the many authors, but the value of the contributions of all who have written on that subject is hereby acknowledged. With a few exceptions the efforts of most students of the subject have been devoted to laboratory investigations of principles. Davis1 was one of the first to report on plant-scale investigations and to present to mill men certain criteria for the guidance of ball-milling practices. His conclusions with respect to the significance of sizing analyses of classifier sands in their relation to the factors of mill speed and ball sizing are particularly referred to. Those conclusions were: 1. If the balls are large or the speed of the mill is high, crowding will appear at the finer sizes in the classifier sands. 2. If the balls are small or the speed is low, crowding will appear at the coarser sizes in the classifier sands. 3. The indications are that best efficiency is obtained when the screen analysis of the sands show a minimum crowding at any size. The last conclusion was qualified by the statement that it had not been proved conclusively. It is surprising, however, that the litera- ture of later years reveals little evidence that millmen have made any serious attempt to apply those criteria. This may, perhaps, be explained by the fact that the average plant-scale ball-milling problem presents so many variables that an investigation of any one of them encounters the problem of control of the others—a problem that often is unsurmountable in a small plant. In a large plant, in which there is a duplication of grinding units in parallel operation, opportunity may be afforded for determining the value of such criteria. Nevertheless, a study of published data from grinding circuits of both large and small plants suggests that either Davis' criteria have been tried and found inapplicable or have never been given consideration. For the purpose of testing Davis' conclusions and with improvement of ball-milling efficiency as the final objective, a test program was initiated in the concentrator of the New Cornelia branch of the Phelps Dodge Corporation early in 1938. The practices of that plant have already been described.2 The fine-grinding units are arranged so that any one of eight units may be operated as a test unit and its results compared with those of the remaining units. All units receive similar feed from a common storage bin, in which the product of the fine-crushing plant is bedded by traveling tripper. The ball mills are all similar in size and operated at the same speeds, and are individually metered. The feeder conveyors of each unit are equipped with Merrick weightometers. The test program as initially outlined proposed investigation of the following:

Jan 1, 1943

By E. H. Burdick

The difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated minerals— pyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying I per cent is considered good grade; 0.7 to 0.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of I .o per cent WO3 is exceptional. Inasmuch as buying specifications demand a 60 per cent W03 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 60 to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent W03, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1943

By Arthur Taggart

Recent jig practice has shown such marked departures from the pronouncements of the textbooks, particularly as to particle size recovered and size range of feed, as to make it desirable to reexamine the mechanism of jig action. This paper presents the results of such a study. The general conclusions of the Paper are: I. A jig bed is a bi-functioned as well as bi-parted body. The upper layer comprises a plastic stream moving slowly in a substantially horizontal direction from feed lip to tail board. It serves to rough out tailing and light middling and to pick up heavy middling and lift it out 01 the jig box. The lower layer acts as the ultimate separating means by absorbing concentrate and rejecting heavy middling. 2. The separating function of the lower layer is performed in three definitely diflerent ways, depending upon the relative sizes of the grains presented to it and those composing it. Experimental The experimental work consisted of close and long-continued visual observations of operating beds in a plunger jig, eccentric driven, and in determinations of the settling rates of various metal spheres through a quartz bed under various conditions of operation. Falling velocities were measured by an ingenious method devised by A. 6. Dorenfeld, a student in the Mining Department at Colum- bia. Spheres of different metallic alloys, 3/8-in. diameter, were cast with a short piece of fine copper wire frozen in to Serve for suspension-A short piece of black cotton thread was looped to the top of the wire to serve as an indicator. The set-up for a test is shown in Fig. I. The thread should be boiled, if necessary, to make it freely water absorbent. The piece of clean plate glass D is supported rigidly at the proper height in a vertical position. The white scale E is similarly supported behind the glass. At the beginning of a test, D is filmed with water by holding it (best with clean rubber finger cots) under running tap water. It is then clamped in approximate position and C, already wet, is laid across it and drawn straight and vertical with the upper end at or near the top of D, and the ball A slightly above the top of the expanded bed. The water film holds the string to the glass. For a test the string is released, its upper end position noted just after the top of the ball becomes submerged, when the corresponding time is read, and thereafter simultaneous readings of position and time are taken as desired. Results of the visual studies of the bed are given at the pertinent places in the following discussion. Results of the settling tests are summarized in Figs- 2 and 3. Definitions The name bed as used herein refers to the entire mixture of solids and water filling the jig box. A layer is a stratum of a bed composed of particles of substantially the same specific gravities. A granular product is long-range when it approximates a crushed or ground product limited as to upper size only; a short-rafzge product is one closely sized. A bed is loaded when operating with continuous feed and discharge of products; it is unloaded when pulsating norma11y but neither being fed nor

Jan 1, 1943

By Gerhard Derge

The extension of metallurgical control of steelmaking processes has always made it desirable to have some quick method for determining the oxygen content of molten steel. To meet the practical demands of the steel industry, this method must also be simple enough so that the sampling can be done by the regular furnace crew. This requirement was kept in mind continually in the work to be described. An oxygen value is required for proper control, whether it be of a rimming steel or of a fully killed steel. However, two factors have discouraged the development of such direct methods: i. The reaction C + FeO Fe + CO is rapid enough to make the correct sampling Of the bath a difficult problem. The most generally accepted means of circumventing this difficulty have been the aluminum-killed bomb test of McCutcheon and Rautiol and the aluminum-killed spoon test of Herty.2 The theory of these tests is that all of the oxygen in the iron is converted to Al2O3, which can then be determined by chemical methods. Even when simplified so that the analysis is made by a measurement of turbidity, this method is too slow to be used in routine control. Furthermore, the results obtained have never been entirely satisfactory, and some of the reasons for this will be discussed later in this paper. z. The ordinary chemical methods of analysis for oxygen in steel are not reliable. The only analysis that seems to possess sufficient dependability to be of value is vacuum fusion,3 and the apparatus and technique developed for this have been too complex and slow for routine work. Indirect Methods Indirect methods of estimating the oxygen have been resorted to in mill practice. Generally these depend upon the chemical equilibria involved. The oxygen in the bath is related to other components in the slag or metal that can be analyzed the readily. These methods have many difficulties in common. Steelmaking processes involve a complicated set of interrelated reactions, all of which tend to approach equilibrium at varying rates. The degree to which any particular equilibrium is approached is not well established. Moreover, a proper use of theoretical equilibrium constants requires a more extensive knowledge of the activities of the con- than we now have. This is well illustrated by the irregularities observed when trying to determine the oxygen in the metal by its ratio to the iron oxide in the slag. Equiliblium relations may be used mole readily if they are evaluated by plant experience, but the extent of approach to equilibrium remains an undetermined variable and lack of an entirely satisfactory mean, of determining oxygen for the calibration is felt keenly, For example, the statistical analysis of the relation between carbon and oxygen4.6 illustrates that even iia a single plant wide variations exist under llormal conditions of operation. Never. theless, this is one of the best methods now

Jan 1, 1943

By Frank S. Gardner, Morris Cohen, Dara P. Anita

There is a conspicuous lack of information in the literature on the precise role played by residual quantities of austenite in heat-treated steels. While retained austenite may be expected to have significant effects on such important properties as the impact resistance of tools and carburized parts and the dimensional stability of dies and gauges, attempts to study these problems systematically have suffered from the absence of a reliable technique for ascertaining absolute amounts of austenite. With such a technique, not only could the relation between residual austenite and service behavior be investigated, but the chemical and heat-treatment factors that control the quantity of the austenite could also be established. Thus, the retained austenite content could then be regulated in accordance with the results desired. The presence of retained austenite may be inferred by observing the changes in properties (hardness, specific volume, electrical resistance, etc.) due to its decomposition on subatmospheric cooling1 or on tempering,2 but these indirect measurements are not readily translated into percentages of austenite. Quantitative determinations have been achieved in special cases by means of dilatometric3 and magnetic4,5 measurements; but the former procedure requires that observations be conducted during the hardening and involves difficult calibrations that limit its applicability, while the magnetic procedure is very sensitive to extraneous influences and depends upon assumptions that can only be considered as approximate in an absolute sense. Furthermore, both the dilatometric and magnetic effects are volume properties, and cannot be conveniently utilized to explore variations in retained austenite from point to point in a suecimen. Some microstructures lend themselves to accurate evaluation of retained austenite contents by metallo-graphic methods,3 but such instances are not too common, and at best, the procedure is tedious. The characteristic X-ray diffraction lines of austenite permit positive identification of its presence; and in the present paper the intensities of these lines, or the corresponding densities* on photographic film, are employed to measure the amount of the retained austenite. In order to cancel the effect of uncontrollable variations in the X - ray exposure and film - development conditions, a standard reference line is Superimposed on each film by maintaining a foil of aluminum in the path of the incident X-ray beam during the entire exposure. With different samples of steel and the same foil, the ratio of the density of some one austenite line to the density of

Jan 1, 1943

By N. A. Stockett

Southeast Missouri is the largest and oldest lead-producing district in the United States. For the year 1941, the statistical picture of pig-lead production, stated in short tons (partly estimated by the Engineering and Mining Journal) is as follows. Tons World production................. 2,000,000 United States Production .........- 460,000 Southeast Missouri production..... 142,000 The consumption of primary lead in the United States in 1941 was approximately 900,000 tons, or almost double the country's production. The largest previous year's in in the United States was 718,000 tons, in 1926. The largest quantities of lead are used for cable sheathing, storage batteries and white lead. During 1941 tetraethyl lead for auto and aviation gasoline consumed 50,000 tons of lead. The entire lead production of Southeast Missouri is now mined by the St. Joseph Lead Co., whose dominant position as the largest producer in the United States of lead directly from ores is best shown by the fact that in 1941 it produced approximately 31 per cent of the lead production of the United States from its mines in southeast Missouri, where 22,000 tons of ore, averaging over 3.00 per cent lead, is mined per working day. It is known that lead was mined at Mine La Motte, Madison County, Missouri, by Renault in 1723. Other white men and Indians probably did some mining prior to that time. Since 1865, the recorded production to Jan. I, 1942, shows that the St. Joseph Lead Co. and the various other companies that have operated in St. Francois County mined lead ore, which, after milling and smelting losses produced 5,980,000 short tons of pig lead. • About 95 per cent of the present lead production of Southeast Missouri is mined in St. Francois County. The northern part of this area is 60 miles south of st. Louis. The remainder of the lead is obtained at Mine La Motte, about 25 miles southeast from the center of the producing area in st.Francois county, Prospecting In this district, most of the ore is discovered by surface and underground diamond drills and by prospect drilling underground with rock drills. Each 2-ft. length of the cuttings from these Jack-hamer prospect holes is assayed for lead. These holes are marked and the records are entered on maps. It has been found that close drilling—100-ft. centers of holes, and sometimes less—is necessary in order to locate most of the smaller commercial ore bodies, many of which previously had been missed by drilling the areas with holes spaced 200-ft. centers or more. To date, geophysical and other methods of prospecting, apart from diamond and Mining Practices of the St. Joseph Lead Company in Southeast Missouri

Jan 1, 1943

By Robert B Sosman

The relative temperature distribution within a coke oven and among the ovens in a battery can be obtained automatically for the operator's guidance by sighting a total-radiation pyrometer on the face of the coke as it is pushed out, and recording the surface temperature. Keeping the instrument clean and keeping its view of the coke unobstructed by smoke and dust are the principal problems. Typical records from three plants are presented in this paper, showing that the temperature patterns are reproducible. Development OF Method The method of coke pyrometry described in this paper was introduced in 1936 by E. A. Lee, then Assistant Superintendent, now Superintendent, of the Coke Plant at Lorain Works, National Tube Co., Lorain, Ohio. At the request of the Coke Committee of the United States Steel Corporation, the Research Laboratory of the Corporation undertook to adapt the method to the somewhat different conditions met with at the Gary Works of the Carnegie-Illinois Steel Corporation, Gary, Ind., and at the Clairton Works of the same Corporation at Clairton, Pa. This work was done in cooperation with the Leeds and Northrup Co. of Philadelphia and later with the Brown Instrument Co. Division of Minneapolis-Honeywell Regulator Co., Philadelphia. We of the Research Laboratory wish to express our appreci- ation of the courtesies extended by Mr. Lee, by A. N. Cole, Superintendent of the Gary coke plant, and by D. P. Finney, Assistant General Superintendent in charge of coke-plant operations at Clairton. We are also indebted to the instrument companies for the loan of a part of the equipment. At Gary and Clairton the instruments were installed and various experiments were made by J. W. Bain, of the Research Laboratory of the United States Steel Corporation. Pyrometry of Coke The coke inside a by-product oven is almost completely inaccessible to pyro-metric instruments. The temperature in the walls can conceivably be measured with thermocouples, but the atmosphere is usually strongly reducing, a condition well known to be destructive to the accuracy of the customary high-temperature couples. In some plants, periodic readings are taken with an optical pyrometer sighted into the top of the combustion flues. This is a useful measure for safety and general control, as it tends to prevent the damage that would result from overheating of the ovens. It does not, however, tell much about the temperature of the coke itself, because of the continually changing gradient in the wall between the coke and the combustion chamber. The best indication of the temperature of the coke itself must therefore be obtained by observation of the product as it is pushed out of the oven. The human eye is very sensitive to variations in brightness of a surface, and particularly to differences in brightness over a continuous hot surface.

Jan 1, 1943

By Gust Bitsianes, Joseph H. M. Beaty

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By H. Brevers, Maurice Rey

Through circumstances connected with the war, the senior author lost his records, therefore it has been impossible to include numerical data in this paper. The arsenical quicksilver ore investigated had been roasted, with poor metallurgical results. The vapor-tension temperature curves of mercury and arsenious trioxide are similar, and the arsenical compound hampers the coalescence of mercury drops in the condenser and is the cause of large stack losses. The ore was a gray limestone carrying small amounts of carbon and mineralized with cinnabar and two arsenic minerals, realgar (As2S2) and arsenopyrite (FeAsS). The proportion of realgar often exceeded that of cinnabar; the proportion of arsenopyrite was smaller. The grade of the ore varied between 0.8 and 4 per cent Hg. The problem was to make a high-grade mercury concentrate, as free from arsenic as possible. The water used throughout the testing was hard, having a pH of about 8. Flotation of Realgar Realgar showed a very strong tendency to float. It formed a film at the surface of the pulp and floated in abundance with only pine oil. Therefore an attempt was made to float the realgar before the cinnabar, but this was not very successful; the percentage of mercury in the realgar concentrate could never be brought below 2 or 3 per cent. Cinnabar slimed easily and floated with pine oil, so that some of it always accompanied the realgar. There was also the question of the cinnabar-arseno-pyrite separation. On further investigation it was found that realgar can be floated not only with pine oil but even better with a combination of hydrocarbons and pine oil. Washing the ore with ether revealed that it contained hydrocarbons, which helped to float the realgar. In this connection it belongs to the same class as carbon, sulphur and talc. It can be floated also with a xanthate, when activated by a heavy-metal salt. The conditions favoring the two types of flotation are opposed, as activation by a copper salt facilitates xanthate flotation (in fact, is even necessary to it), whereas it hinders pine oil and petroleum flotation. One type of flotation can be termed non-polar and the other polar, a distinction that has been stressed in a previous paper.' Depression of Realgar and Flotation of Cinnabar Many chemicals were tested in an attempt to float the cinnabar and depress the realgar. Finally starch rendered soluble with caustic soda was tried, also several grades of commercial soluble starch, and dextrin was found to be the best and the most convenient reagent. Several of these starch preparations have a strong flocculating effect on the pulp, which is a distinct disadvantage. Dextrin, with its low flocculating power, is excellent. It is noteworthy that starch preparations are also depressants for carbon and talc, so that the fact apparently has a general

Jan 1, 1943

By H. A. Doerner, F. D. DeVaney, J.B. Clemmer

Production of magnesium metal in the United States during the past decade has increased from less than 600,000 lb. in 1928 to more than 4,800,000 lb. in 1938.1 The growing industry has stimulated interest in methods of production and in sources of raw material. All of the present domestic production is from brines. However, the availability of large tonnages of magnesite in the state of Washington, together with the possibility of cheap power, have created interest in the utilization of magnesite for the production of magnesium metal as well as for other purposes. Magnesite, the carbonate of magnesium (MgCO3), usually is associated with limestone (CaC03) and dolomite (MgCO3. CaC03). It occurs in crystalline and microcrystalline (sometimes termed amorphous) forms.2 The more common crystalline mineral is found in various shades of white, gray, yellow and brown, the colors being due to impurities, chiefly iron. Magnesite has a hardness of 3.5 to 4.5 and a specific gravity of 3.0 to 3.1. It forms rhombohedra1 crystals in the hexagonal system, having a vitreous, pearly luster. The quarries and mines of the Northwest Magnesite Co. near Chewelah, Wash., are large producers of magnesite for refractories. The deposits are extensive, some veins being hundreds of feet wide. The boundaries of the veins are indefinite, and the magnesite is interfingered with dolomite. Calcite, talc, serpentine, quartz and shale are disseminated through the deposits. The quality of the ore cannot be determined by appearance or by simple tests; chemical analysis is required. These features make it difficult to determine the boundaries or total quantity of workable ore.3 Only the higher-grade ores are mined, and a considerable proportion of the magnesite content is discarded by hand-sorting and log-washing methods. After calcining, the sorted product meets the specifications for usual refractory material, as it contains approximately 81 per cent MgO, 7 per cent SiO2, 6 per cent CaO and 6 per cent Fe203 + A1203. A sample of the reject material had the following analysis after calcining: 65.4 per cent MgO, 6.3 CaO, 21.1 SiO2 and 6.5 R2O3. The percentage reported as R2O3 includes compounds whose chlorides are acid-soluble but give precipitates in ammoniacal solution that are ignited and weighed. The more common constituents are Fe2O3, A1203 and TiO2. The sorted magnesite product is not the best grade. even for refractory purposes, and leaves much to be desired for a reduction process. The rejected material contains a large proportion of magnesite. It is apparent that an effective concentration method would yield a higher recovery and a better product. In general, the refractory grade is not suitably pure for other uses. Recent developments in the production of

Jan 1, 1943

By R. C. Earlougher

Based on laboratory tests conducted with the use of fresh core samples as well as a considerable amount of field data obtained from numerous water floods in northeastern Oklahoma, it appears that for any given oil saturation there is a critical maximum velocity above which the oil-recovery efficiency falls off very rapidly. In effect, when a water flood is operated above this critical velocity, the injected water-oil ratio rises extremely fast, thus shortening the economic life of the flood and reducing the ultimate oil recovery. This critical velocity apparently varies considerably with the percentage of oil saturation of the sand, so that in effect the higher the oil saturation at the beginning of a flood the higher the velocity that can be used successfully. In reviewing several of the earlier floods in the Mid-Continent area, it is concluded that most of the failures were due to two things: (I) too low an oil saturation, such as 30 per cent, and (2) too high water-injection rates, Although considerably more field data are necessary to establish definite limits, it would seem that the proper field injection rate for a 330 by 330 or 440 by 440-ft. spacing varies from approximately I bbl. per foot of sand per day where the oil saturation is as low as 30 per cent up to 5 bbl per foot of sand per day when the oil saturation is as high as 45 to 50 per cent, Introduction With secondary recovery by water-flooding receiving more and more attention throughout the industry, a greater working knowledge of multiphase flow under field conditions becomes more and more necessary A great deal of research has been carried on in highly idealized laboratory conditions, from which certain trends have been indicated, but with few exceptions no direct application to field use has been reported. widely varying conclusions have been drawn from the mass of idealized laboratory experiments and often this divergence apparently was due to the neglect of connate or interstitial water. Since interstitial water is such an important factor in water-flooding operations, it then follows that any laboratory flooding experiment must necessarily take it into account; and since it is difficult to set up laboratory models to allow for interstitial water, the next best procedure is to use fresh core samples for such tests. Even this procedure has its difficulties, inasmuch as it is possible to run only one flooding test on each sample, as each sample differs somewhat in character from all other samples. However, this disadvantage can be overcome to a large degree by the use of an extremely large number of samples. The next question that arises is: "IS it possible to get uncontaminated core samples having a true oil and water saturation like that existing in the reservoir?" If the sand under consideration is still in the primary stage of production, with a normal or relatively high amount of gas still in solution in the oil, probably it is not possible to get a nonflushed core. On the other

Jan 1, 1943

By V.K. Zworykin

Throughout its development the science of electronics, like so many other branches of science and industry, has been indebted to the metallurgist. Metallurgy has provided the electronic engineer with conductors to furnish passage for electrons outside of his evacuated tubes: it has developed tungsten and tantalum wires for emitting electrons and various refractory metals and alloys suitable for electrodes, which receive them and guide them within the tube; finally it has supplied ferromagnetic materials both for shielding electronic apparatus from magnetic fields and for forming highly concentrated fields for deflecting electron . Today I hope to show you that electronics has not been altogether ungrateful for this assistance. More specifically, I wish to indicate the role that the electron microscope, a relatively recent product of electronic engineering, is playing even now in the study of metals. Every metallographer is aware that his standard metallographic microscope will not reveal structural detail involving separations smaller than a certain fraction —at the very best a tenth—of a micron. This limitation, he knows, is a consequence of the fact that the wave length of the light employed for forming the image has this order of magnitude. It is, thus, a property of all light microscopes. TO overcome it, a different imaging medium must be employed, The existence of such a medium became evident when it was demonstrated1 that electrons were affected by magnetic and electric fields with axial symmetry just as light is affected by glass lenses; these fields, or "electron lenses," curve the paths of electrons reaching them from an object located on the axis of symmetry in such a manner that, at some distance from the lens, a true image of the object is formed. Furthermore, although a wave length may . be ascribed to electron beams just as to light, this wave length is much shorter; for electrons accelerated through a difference of potential of 50 kilovolts, the wave length is only about one hundred-thousandth of that of visible light. Actually, the elcctron microscopes of today resolve detail one hundred times as fine as light microscopes; if the maximum useful magnification of the latter is taken to be a thousand, that of electron microscopes is one hundred thousand. The Electron Microscope Since electrons are readily scattered and absorbed by matter, specimens to be observed in the electron microscope must be prepared to be less than one micron in thickness; furthermore, the interior of the microscope must be carefully evacuated to prevent collisions between the clectrons and the molecules of the air. Finally, as already mentioned, the lenses are formed by axially symmetric magnetic or electric fields, and not by any material medium such as glass. Apart from these basic differences, the electron microscope closely

Jan 1, 1943