Search Documents

By H Haas

H. HAAS, San Francisco, Cal. (communication to the Secretary?). -Fig. 1 plainly shows that the comparison of the steam-turbine and Diesel-engine plants was made on a basis of 6,000 kw. continuous operating load. The tabulation of costs for an 8,000-kw. load is merely done to show the relation of increased output on' the unit power costs. Both plants would sacrifice their reserve capacity, which is to insure continuous operation, if operated to generate 8,000 kw. continuously; unless Mr. Hawkins advocates the operation of one of the turbines at 33.33 per cent. overload, retaining the other as a standby, which, besides overtaxing the turbine, results in a great loss of efficiency. It would he well for Mr. Hawkins to qualify certain of his statements. Thus, under the caption "Diesel Engines, Selection of Units," he says that "two of the largest Diesel-engine builders take the position that, in the present state of the art, they would not attempt to put out units over 1,000 kw.;" he should qualify it by saving that "two of the largest American Diesel-engine builders take the position that, in the present state of the art in the United States, they would not attempt to put out units over 1,000 kw." The reason that American manufacturers restrict themselves at present to units of that size is to be found not so much in a lack of experience in building large units as in a lack of a sufficient, demand for them in the United States to justify the heavy capital outlay connected with the development of such engines. There are relatively few localities in the United States where fuel prices are as high as they are in the Southwest, and regions of high fuel prices are sparsely settled and have a very limited demand for power. Where low fuel prices obtain, steam turbines are active competitors of Diesel engines for large power plants, particularly when the station load factor is low. As most of the American manufacturers of Diesel engines work under license agreements with European manufacturers, which limit their market to the United States and its possessions and Canada, a further limitation is imposed upon them, leaving to European firms practically the entire world as a market.

Jan 5, 1917

The first prize of the President's Prizes has been awarded to J. J. Beeson for his paper entitled "Disseminated Copper Ores of Bingham, Canyon." When this paper-was written, Mr. Beeson was a student at Stanford University, and was president of the Stanford Geological and Mining Society. The President's prizes were established in 1915, funds being provided, at that time for three prizes of $50, $30 and $20 respectively, for the best essays, or other papers submitted in competition by Junior Members and Members of Affiliated, Student Societies. The original intention was to award all three during the year 1915, but the committee has deemed it advisable to extend the time for the second and third prizes, and the Secretary of the Institute will be glad to hear from any member who wishes to compete for one of these prizes. A competitor for the President's Prizes must be, at the time of submitting his essay, either a Junior Member or a Member of an Affiliated Student Society of this Institute. The essays must be upon some subject related to Mining, Economic Geology, or Metallurgy. I11 malting the awards, special weight will be given to originality in investigation and treatment; and to 'literary merit. As a general rule, the essays should not be less than 3,000, nor

Jan 5, 1917

By H. H. Stoek

MINE models have three distinct uses: 1. As exhibits in expositions and museums. 2. As exhibits in law suits. 3. As illustrations in teaching mining engineering. All three uses are in a sense educational. The third, or distinctively teaching function, has not been extensively developed in America as it has been abroad, chiefly because of the cost of the models and the scarcity of model makers. In connection with expositions, such as the Columbian, the Louisiana Purchase, and the Panama-Pacific, a number of very good mine and metallurgical models were prepared with funds furnished by State commissions, by mining organizations or mining companies. At the close of these, expositions, some of these models have been deposited in National or State museums or in educational institutions, but too many of them have been lost, or have been stored, away in some mining company's office or in the basement of some State building, where they have been lost sight of and have gradually fallen to pieces. A visitor to a German mining school is impressed by two facts: 1. The mining laboratories are in general inferior to those in America. 2. The mining museums are infinitely superior -to ours, particularly in models exhibited. One may reply to this comparison by saying that a museum is necessarily a work of time. From the historical standpoint this is, of course, true, but it is not necessarily true in connection with a working museum intended to illustrate current practice. For instance, the oldest mining school in Germany, that at Freiberg, has much excellent historical material, but very little on modern practice, while Berlin, one of the youngest German mining schools, has a most extensive and valuable collection of modern appliances and models. This is true in spite of the fact that one of the best-known model shops is at Freiberg, from which many of, the models to be seen in America have come. Because many of the models in American mining schools have come from

Jan 4, 1917

By Linn Bradley

F. H. WILLCOX, Pittsburgh, Pa. (communication to the Secretary*). -We must keep in mind, in balancing the savings-to be anticipated by the most efficient combustion of gas, the best heat absorption by stoves or boilers, and by heat conservation of the thermal equivalent carried in. blast-furnace gas-against the cost in operation, maintenance, depreciation and interest charges of the equipment required to realize the savings, that in boilers and hot-blast stoves we are basing our economies upon two different, combustion phenomena. In a boiler, evaporating water at a heat efficiency of 70 per cent., approximately 47,550 B.t.u. is consumed per boiler horsepower. Taking the blast, furnace gas cited in the above paper, we are using about 38 ¾ lb. of cold-washed gas per boiler horsepower. Using the hot-cleaned gas, the same equivalent heat is furnished by 34 1b. of the gas , This leaves of the 38 ¾ lb. required in the case of cold-washed gas, 4 ¾ lb. or 6,650 B.t.u. available for raising more steam when dry-hot gas is used, which means that an equivalent amount of coal firing can be dispensed with. Per ton of iron, this figure 2/3 X 12,000/38.75 X 4.75 = 980 lb. gas or 1,372,000 B.t.u. or 100 lb. coal. At $1.50 per ton of coal, the net saving per ton of pig iron produced by the use of dry-hot over wet-cold cleaning will, therefore, be about $0.06 2/3. At a stove heating 8,500 lb. of air per toil iron from 150° F., one-quarter of the dry-hot cleaned gas, or 3,000 lb., would heat the air to 1,450° F. 3,000 X 1,400 X 0.70 = (8,500 X 0.255) = 1,300. The cold-wet gas would heat the same amount of air to 1,280° F. 3,000 X 1,225 X 0.70 = (8,500 X.0.255) = 1,130.

Jan 4, 1917

By A. E. Bellis

THE CHAIRMAN (ALBERT SAUVEUR, Cambridge, Mass.).-Any information likely to throw light on the constitution and proper treatment of high-speed steel in order to obtain maximum results, should surely he welcomed. All users of high-speed steel, I believe, will agree with the authors that, in order to obtain satisfactory results, it is not sufficient to heat all brands of high-speed steel to one and the same temperature; apparently very slight differences of chemical composition seem to call for marked differences in temperature. I think that all of us agree that a properly treated piece of high-speed steel should have a fine austenitic or polyhedral structure and that an appreciable quantity of free carbide may be present in the case of very high tungsten steels. What we seem to lack is a satisfactory method, quick and reliable, of ascertaining when the proper structure has been obtained. I think Mr. Bellis' paper is a step in the right direction. To the untrained eye, however, it is not an easy matter to select from some of his photomicrographs the one representing the best structure; for instance, in the case of steel A, we wonder why temperatures of 2,250 and 2,300 do not yield the same results, seeing that both structures are apparently alike, and the same might apply to some of the other samples. I have no doubt, however, that the experienced observer is capable of detecting structural differences that are not made plain here and by which he is able to select the proper quenching temperature. COLIN G. FINK, East Orange, N. J.-On page 68 the authors say that the use of a barium chloride bath to eliminate this difficulty has the disadvantage that the surface of the tool becomes decarbonized." I would like to ask whether they actually found that the surface was decarbonized, or whether they base this conclusion on softening alone? A. E. BELLIS, Springfield, Mass.-No, we have never demonstrated that it was a decarbonization, it is just the softening of the steel. The addition of ferrocyanide to the ferrochloride bath has been suggested. I think that is not altogether satisfactory, because the ferrocyanide bath changes composition very rapidly at these high temperatures, and it would be just a question of luck whether or not it had too much or too little ferrocyanide in the bath giving equilibrium with the carbon content.

Jan 4, 1917

ALEXANDER BURRELL Alexander Burrell, general manager of the Furnace Creek Oxide Copper Mining Co., and' a member of the Institute for 20 years, died suddenly at the Argo mine on Feb. 13, 1917. Mr. Burrell was one of the best known mining men in Montana. He was horn at Edinburgh, Scotland, Jan. 14, 1851, and came to Chicago with his parents in 1856. His father, who was a coppersmith, died soon after their arrival, and the ,son had few opportunities to gain an education in school, but was a natural student and was possessed of a liberal education acquired through self-teaching and through his constant reading and studying, particularly along scientific lines. It was this technical knowledge both of mining, and business, as well as his experience in the practical side of mining and his ability as an executive that won for him a high place in mining circles in Montana. As a very young man he worked as a miner in Illinois and later became an operator of a coal property. Subsequently he engaged

Jan 4, 1917

By F. R. Van Horn

WALLACE MCKEEHAN, Douglas, Ariz. (communication to the Secretary*).-In going over this report, which I have done very carefully, I find that the summary as composed deals with the various problems almost entirely from the employer's standpoint and that practically no consideration is given to the employee's point of view. An experience of 3 ½ years as safety inspector, and almost 30 years as workman-and official, has convinced me that any plan for the betterment of working conditions which will achieve any degree of success must give the workmen their share of responsibility and allow them full participation. The company may finance and direct the movement, but its ultimate success depends upon the support given by the workmen. The cooperation of the men doing the actual work is so essential that all writers insist that this must be secured, but they do not agree as to how this can best be done.

Jan 4, 1917

In accordance with the usual custom, manuscripts to be presented at the next meeting of the Institute must be in the hands of the, Secretary before July 1, 1917. Manuscripts to be properly distributed in advance of the meeting must be in the hands of the Secretary before June 1, 1917. At the last meeting of the Institute 45 papers were presented, and 42 of them were actively discussed. This experience makes us believe that advance distribution is the best possible means of getting a good discussion of papers and of securing for them the interest of the members of the profession. It will be impossible, however, to give the papers proper distribution if they bare not received before June 1, 1917.

Jan 4, 1917

By E. M. Chance

HERBERT M. WILSON, Pittsburgh, Pa. (written discussion).-Permit me to endorse the author's conclusions and their form of presentation as ,being, in my judgment, the last word 'on the subject of lights for the illumination of coal mines. I also feel that the open-flame oil lamp has outlived its usefulness, and that it should go, in the interests not only of safety but of efficiency. Where an open-flame lamp can be used with safety in non-gaseous mines, the acetylene light adds materially to efficiency by its better illumination, and to safety for the numerous reasons given by Mr. Chance. The latter, however, lays chief stress on the value of the acetylene because of its non-fouling and non-obscuring effect on the atmosphere. Another important advantage over any other form of illumination is the clear, bright light projected at the point where the workman may look for danger. The better illumination materially safeguards the worker against obstacles over which he may stumble when traveling, and against dangers from falls of roof or of coal, weakness in timbering, and similar conditions. The acetylene lamp, where it may be used with safety, has advantages even over the present electric cap lamp, in that it gives a higher luminosity; and when the miner comes to learn its signals, as he will in time, just as he learns those given by the open-flame or the safety lamp, he will find that the acetylene lamp is a fair detector not only of methane but of carbon dioxide, as clearly shown by Mr. Chance. The only, serious objection, raised against the use of carbide lamps. has been recently in Pennsylvania, due to the belief of the State Mine Inspection Department that it endangered miners working on pillar work, or other places where carbon dioxide might accumulate, or where there is lack of sufficient ventilation, and because it was believed that the indications of the carbide lamp would not give the miner sufficient warning. On this point Mr. Chance has clearly shown the fallacies of the objections. I may add that for those unable to detect carbon dioxide with the acetylene lamp, the maximum of protection would be afforded by using an open oil lamp or a flame safety lamp in such places; or, because the miner might not watch his oil light, a better, protection still would be offered by a sufficient number of daily inspections of such working places by a fire boss or other official, with flame safety lamp.

Jan 4, 1917

By Frank Schrader

J. DANA SPERR, Jerome, Ariz. (communication to the Secretary*).¬Very little accurate information has been published about this district. Most of the geological data appearing in the technical press are based on "careful observations" made from an auto stage and a casual glance through the U. S. Geological Survey Bulletins, No. 340 of 1908 or No. 397 of 1909, both by F. C. Schrader. Mr. Schrader's report is still the best publication on the district. A really careful study of this report will uncover only a very few statements which have since proven questionable. This is a remarkable record when it is considered that only a short time was spent by Mr. Schrader in the field and that there was very little development work done at that time. The mining world and especially Mohave County, Ariz., will feel a sense of gratitude to Mr. Schrader for revising his early report. on this

Jan 3, 1917

By E. Maltby Shipp

WALLACE MCKEEHAN, Douglas, Ariz. (communication to the Secretary*).-In going over this report, which I have done very carefully, I find that the summary as composed deals with the various problems almost entirely from the employer's standpoint and that practically no consideration is given to the employee's point of view. An experience of 3 ½ years as safety inspector, and almost 30 years as workman-and official, has convinced me that any plan for the betterment of working conditions which will achieve any degree of success must give the workmen their share of responsibility and allow them full participation. The company may finance and direct the movement, but its ultimate success depends upon the support given by the workmen. The cooperation of the men doing the actual work is so essential that all writers insist that this must he secured, but they do not agree as to how this can best be done.

Jan 3, 1917

By A. Patton

Introduction THE use of roll scale in the Bessemer process dates back, to the "best of our knowledge, at least 20 years. It was first used by the Ohio Steel Co.; Youngstown, Ohio (now the Ohio Works of the Carnegie Steel Co.) under the direction of Sam, MacDonald, Superintendent of the Bessemer Department at these works. Two 10-ton vessels and one blowing engine capable of blowing one heat at a time were employed. The object of using the scale was to -shorten the length of the blow; or in other words, to increase the production with the same equipment. Various means were tried out for introducing the roll scale into the bath of molten iron: It was shoveled into the vessel before the heat was charged, so that the metal would flow over the scale; it was shoveled into the bath after the vessel was turned up; it Was dumped into the empty iron ladle by the wheelbarrow-load, and at times wars dumped on top of the molten metal in the iron ladle. But the practice of introducing the scale into the iron ladle had to be abandoned on account of danger from explosions and of skulling the -ladles. It was soon learned that the proper place to charge the scale was in the empty vessel, so that when the molten iron was poured into the vessel it flowed over the scale, causing a considerable reaction to take place before the heat was turned up. Eventually, cylindrical chutes similar to those now in use were installed. Into these chutes the scale is dumped and carried into the empty vessel. Before this convenient means of introducing the scale was adopted, the Ohio Works had satisfactorily demonstrated that roll scale would increase production, by blowing 107 heats in one 12-hr. turn (1,087 tons) with one blowing engine, blowing one heat at a time; whereas, prior to the use of scale, the best practice at these works was about 80 heats under the same conditions.

Jan 2, 1917

By Linn Bradley

Introduction MARKED differences of opinion have been expressed by engineers interested in cleaning iron blast-furnace gases for use in hot-blast stoves and under boilers, in reference to the advantages of a hot-dry method over a cold-wet method. One point at issue involves the sensible heat energy in the moisture contained in the gas. Some advocates of the cold-wet methods claim that the condensation and resultant removal of the greater portion of this contained moisture by wet scrubbing, spraying or similar methods, results in a saving of some of this sensible heat energy, by reason of the fact that water vapor has a high capacity for sensible heat energy and may carry from the exit of a hot-blast stove, for example, more heat units than are sacrificed or lost when the gas is cleaned by this cold-wet method. Other advantages claimed for the latter method are: That gas burns more readily when it is free from moisture in any form; that because gas is made denser by cooling and removing the moisture it has a higher calorific value than hot gas carrying moisture; and that higher flame temperatures are obtained when the gas is cleaned by the cold-wet method. A search through the available literature fails to disclose any extensive calculations or records of conditions obtained in practice, bearing upon these phases of gas cleaning. This paper deals with these problems from the standpoint of the economy of using a gas of higher flame temperatures, of improved stove design, and of economy in the gas-cleaning department. Calculations have been made which show that by cleaning the gases by a cold-wet method the sensible heat energy of the blast-furnace gases is greatly reduced; and, in general, this loss of heat energy is far greater than that lost from the stoves or boilers due to the sensible heat capacity of the water vapor if carried away by the exit gases. By making use of the

Jan 2, 1917

By Carle Hayward

IN reheating quenched steel to remove part of the hardness, the softening effect has generally been considered to be a function of temperature and time. The temperature effect is well known, and long before pyrometers were heard of the blacksmith was able to do a good job of tempering, by rule-of-thumb methods and experience in judging temperatures. Modern conditions, which demand steel that will withstand the severest tests, require that the heat treatment he carried out with every possible precaution to secure the best results obtainable. Pyrometers and heat-treatment furnaces of many types are on the market and improvements are continually being made so that it is now possible to regulate the temperature in heat treatment very accurately. There is -still a question regarding the time that the steel should be subjected to treatment. It is customary with all operators to insure the desired tem-pressure throughout the specimen and it is generally supposed that a longer treatment of a hardened steel produces a further softening but there are few published figures showing the exact effect of time of treat-ment at constant temperature. A search of the literature disclosed several brief statements that the tempering effect was a function of both time and temperature, but in no case were any figures given. The opinion is very generally held that the well-known tempering colors are accurate indicators of the degree of tempering. This is disputed by Brearley (The Heat Treatment of Tool Steel, page 102) who states: It has been said that the result would be the same in respect to both hardness and other properties whether the colors were obtained by a shorter heating at a higher temperature or a longer heating at a lower one. This, to say the least, is a very doubtful conclusion, and is certainly not borne out by mechanical tests on oil-hardened and tempered motor car steels, which, after tempering for periods varying from 15 min to 2 hr., show no very great differences. The present investigation had for its object the obtaining of some definite data regarding the effect of time, which might serve as a guide to those engaged in the heat treatment of steel. The Rhode Island Tool Co. cooperated by furnishing the steel and machining the test specimens.

Jan 2, 1917

By Joseph T. Singewald

The possible value of the red hematite iron ore of the southern Appalachian States, if some practicable method of concentrating it could be devised, has long been recognized. The ore is very low grade, and although in enormous quantities, particularly in the States of Alabama, Tennessee, and Georgia, is only at a few points rich enough to work, and even the best of it ranks among the lowest grade iron ores being mined in the United States. A cheap method of beneficiating this ore would make enormous quantities available and vastly increase the iron-ore resources of the country. However, this low-grade ore in effect constitutes a potential iron reserve, and as long as ample quantities of ore can be obtained elsewhere the question of its utilization does not demand immediate notice. Where these ores are in part of workable grade, however, a problem of more immediate importance arises which, from considerations of economy and prevention of waste in their mining, ought to be solved or, at least, attacked as quickly as possible. Where these ores are being worked they are usually intimately associated with lower-grade material that in mining is left behind. The difficulty and expense of going into ground broken by old workings makes the recovery of this lower-grade ore practically impossible and it is lost forever. Success in concentrating the red ores, therefore, would save material that is now being irretrievably lost. The successful large-scale concentration of law-grade ore in the last few years on the Lake Superior iron ranges should encourage the attack of similar problems in the Birmingham district.

Jan 1, 1917

By A. E. Bellis

The problem of heat treating high-speed steel becomes more and more important as the design of cutters becomes more and more complicated in increasing the efficiency of mechanical operations. Hundreds of dollars' are spent in the design and manufacture-of milling cutters of special form ,for rapid production of duplicate or interchangeable parts, and then, as the heat treatment is faulty on the one hand, or scientifically executed on the other, the tool fails after a few operations, or its efficiency is greatly increased. The practical operation of giving these complicated tools the right temperature necessary to bring out the best cutting qualities, and at the same time bring the tool out "clean," is a difficult: one and calls for no small amount of skill. In order to be on the safe side, the average tool hardener uses a temperature much too low to give the best results with the high-speed steel he uses. In the case of cutters which are finished to a given diameter before hardening, it is impossible to grind the tool after hardening, so that it is essential that the surface be-protected from oxidizing or de-carbonizing. It is the aim of this paper to describe some experiments on hardening high-speed steel, in which metallographic means were used to determine the correct hardening temperatures. The accompanying table and plates show the results of hardening experiments on five different high-speed steels. The analyses for carbon, tungsten, chromium and vanadium of each steel are given in the accompanying table. Six specimens from the same bar :of each: kind of steel

Jan 1, 1917

By Linn Bradley, W. W. Strong, H. D. Egbert

A hot-dry method of cleaning the gas from blast furnaces has been shown1 to conserve the sensible heat energy of the gas, and in general it thus permits of a higher flame temperature. The electrical method of cleaning gases removes from 98 to 99 per cent. of the suspended matter in one operation when operating properly, thus making possible the use of a very clean gas for burning in the stoves. The use of such clean gas thus makes feasible a different type of hot-blast stove construction from that being used at present. It therefore seems advisable to construct the stoves from the viewpoint of getting the maximum amount of heat energy into the products of combustion. By preheating the air added to the top gas and obtaining a better mixture of the air and top gas, less excess air will be required and a higher flame temperature obtained from the combustion of the top gas. The interior of the stove should be provided with a kind of brick that will withstand a high flame temperature, will conduct the heat energy along certain directions, insulate the flow of heat along other directions and at the same time store heat energy so as to make the flow of such energy more uniform. It is quite likely that these results can be best obtained by using several kinds of bricks: one type which is a good insulator of heat energy to be used for lining the stove and for making partitions through the stove to restrain the flow of heat; another type of brick or material with high refractory qualities; and a third type which will be a good conductor of heat energy. The surface of the stove exposed to the atmosphere should be a minimum in comparison to the mass of checkerwork which it is possible to obtain, due regard being paid to other conditions. With clean and hot furnace top gas it will be advisable to consider a rearrangement of the checker work in the stoves. One season for the present size and shape of checker openings is to provide facility for

Jan 1, 1917

By Joseph P. Hodgson

Since about 70 per cent. of the total cost of mining is due to underground work which is out of sight, it is essential that expenditures should be made here to the best advantage. A great many mistakes have been made which were expensive, but perhaps these have not even been detected by mine owners. In the future these may be minimized to some extent, especially if there is cooperative effort on the part of each employee. I have been interested in this subject for some years and have tried to deduce principles and methods. These have proved highly advantageous and may also be of help to others. Some corporations, like the United States Steel, and the Cleveland-Cliffs Iron Co., have done a great deal in this field by having stated meetings of their organizations, with the view to interchanging ideas among their men and educating them along the lines of concerted effort. Since no man knows all about the various branches of mining, it is advisable that frequent meetings of the operating department be held for the interchange of ideas and that all members of the organization have an opportunity to express themselves on the various subjects. It has often been found that in discussions between heads of departments, foremen and bosses, many valuable suggestions may be obtained which promote the best interests of the company. The method regarded as the most conducive to cooperative effort, and pursued by the organization, is to analyze and develop the different phases of various mining subjects at regular meetings. Nine Foremen's Dinners In the latter half of 1912, the Copper Queen Consolidated Mining Go. gave monthly dinners to the men in the operating departments. Those who attended were superintendents, foremen, shift bosses, engineers, geologists, and heads of all departments, making a total of about 75 men. After the dinner, lectures were given on subjects which pre-

Jan 1, 1917

Through the generosity of Sir Robert Hadfield, Honorary Member, the Directors of the American Institute of Mining Engineers are enabled to announce the Hadfield Research Prize of $1,000 for the best contribution to the publications of the Institute upon the general subject of The Different Forms and Combinations of Carbon with Iron, including those in Iron Alloys. The prize will be awarded at the Annual Meeting of the Institute in February, 1916, to the best paper upon this subject which is presented to the Institute before Nov. 1, 1915, provided such paper is deemed worthy by the Institute's Iron and Steel Committee. The following suggestions are also added for the guidance of those who may take part in this research. While it is not desired to define closely the exact lines or scope of the proposed research, as it is advisable to make these as broad as possible, the object in mind may be said to be generally as follows: To elaborate and find out the best methods of determining the forms of carbon in steel or iron, including those in iron alloys. A portion of the work would probably be a continuation of the researches which have in the past been carried out by Jullien, Abel, Muller, Ledebur, T. Sterry Hunt, Akerman, Arnold, Stead, E. D. Campbell, Hogg, Parry, Upton, and others.Through the generosity of Sir Robert Hadfield, Honorary Member, the Directors of the American Institute of Mining Engineers are enabled to announce the Hadfield Research Prize of $1,000 for the best contribu¬tion to the publications of the Institute upon the general subject of The Different Forms and Combinations of Carbon with Iron, including those in Iron Alloys. The prize will be awarded at the Annual Meeting of the Institute in February, 1916, to the best paper upon this subject which is presented to the Institute before Nov. 1, 1915, provided such paper is deemed worthy by the Institute's Iron and Steel Committee. The following suggestions are also added for the guidance of those who may take part in this research. While it is not desired to define closely the exact lines or scope of the proposed research, as it is advisable to make these as broad as possible, the object in mind may be said to be generally as follows: To elaborate and find out the best methods of determining the forms of carbon in steel or iron, including those in iron alloys. A portion of the work would probably be a continuation of the researches which have in the past been carried out by Jullien, Abel, Muller, Ledebur, T. Sterry Hunt, Akerman, Arnold, Stead, E. D. Campbell, Hogg, Parry, Upton, and others.

Jan 1, 1917

By David B. Scott

When mining operations were first instituted in the mines of the Miami Copper Co., at Miami, Ariz., the relatively hard character of the ground in the western section of the property made it seem advisable to use a wide shrinkage stope and pillar system. The system as finally evolved was applied to the mining of 2,300,000 tons of ore by the use of stopes and pillars each 50 ft. in width. Development, mining and extraction of this reserve has been continuously in progress since 1910, and the final stages of extraction are now reached. A complete survey of all phases of this system can therefore be made. Modification in working methods was obviously necessary, and the system to be described is believed to be typical of the best features. Development The preliminary work had three main objectives: The opening of a haulage level, the construction of a drawing-off level, and the driving of sublevels for use in stoping. In addition to these, some extra sublevel drifting was necessary to determine exactly the boundaries of the orebody, the general outline having been determined by churn drilling. This development was based on the requirements of stopes 50 ft. wide, with pillars 50 ft. wide between each stope. The length of these units varied from 200 to 500 ft.. Haulage Level The tramming level was 50 ft. below the floor of the stopes, and the tramming lines were run parallel with the long axis of the stopes. These lines were also beneath the middle of the stopes and pillars. Each line therefore served one stope or one pillar, this arrangement making it possible to load along an entire stope without switching or uncoupling. This advantage is apparent principally during the process of stoping when rapid drawing of excess broken ore is desirable. Furthermore, the arrangement of the drawing-off level chutes at 25-ft. intervals, as shown

Jan 1, 1917