Search Documents

By William Skinner, Jonas Addai-Mensah, Keith Quast, David Robinson, Jason Connor

A review of the laboratory- and pilot plant-scale physical separation techniques for the beneficiation of nickel (Ni) laterites shows limited efficacy. To date, the only upgrade technique adopted commercially, prior to hydrometallurgical processing of Ni laterites, is the removal of a barren, coarse size fraction in the feed by classification. In the present work we investigated two low grade (~ 1%), goethite-rich Ni laterite ores’ upgrading by magnetic separation, attritioning/coarse, (lower Ni-grade) gangue rejection and flotation techniques. Low intensity (0.1T) dry magnetic separation at ambient temperature of raw samples and those pre-heated at temperatures up to 450 °C showed evidence of pay metal Co and Mn bearing asbolane and/or lithiophorite minerals pre-concentration in the magnetic fractions. Ni distribution, however, did not show any noticeable magnetic upgrade but followed the weight distribution. Other ore pre-treatment methods (e.g., desliming and sulphidisation) followed by froth flotation with anionic and cationic reagents also led to noticeable (~35%) Ni upgrade. This is due to the deportment of Ni across several gangue host mineral phases (i.e. Fe oxide/hydroxide and a range of silicate/aluminosilicate minerals). From chemical analysis, after disaggregation of ~ 1% Ni grade feed ore, coarse (-600 + 38 µm) and fine (-38 µm) fractions of ~0.6% and 1.3% Ni grades respectively, were also produced, suggesting that a significant upgrade in Ni content can be achieved by rejecting the + 38 µm fraction with the loss of <40% of the Ni. The ore mineralogy, particularly the complexity and high number of un-liberated Ni-bearing phases, greatly compromises physical separation methods for these ores, with the possible exception of screening after disaggregation of the fines inherent in the run of mine ores.

Jan 1, 2014

By Roger A. Blais, Michel David

"Matheron&apos;s geoslalislical method for the estimation of ore reserves has been developed to the point at which real-life problem may be handled effectively. The steps involved in the method are:(i) obtalning the variogram,(ii) fitting a model, and(iii) producing block estimates.All three steps may cause difficulty, and would-be users need a deep understanding of the theory if failure is to be avoided.To illustrate these points, specific cause are considered:(i) two almost equidimensional porpbyry deposits, one drilled randomly and the other regularly; and(ii) two iron formation, one drilled extensively and being mined, while the other is still at the stage of early estimation."

Jan 1, 2014

By Tristan H. Jones

Rib-related accidents in underground coal mines continue to cause injuries and take lives at a rate of 1.3 fatalities per year for the last 17 years. Prevention of these accidents cannot simply be a matter of installing more rib support, though the eventual final solution will undoubtedly include that component. Ultimately, rib safety will be brought about through an understanding of the causes and mechanisms that cause rib fatalities, and by fine-tuning mining methods and procedures that are currently in place. This paper investigates the factors likely to be most influential in the occurrence of rib fatalities. A careful analysis has been conducted of the rib fatality reports documented by the Mine Safety and Health Administration between 1996 and 2013. The primary outcome is the determination of the relative impact of each type of rib fatality factor and a better understanding of the impact each factor has. Among the rib fatality factors considered, the influence of rib profileis considered for the first time. Mining height, rib stratigraphy, mining cycle, and the standing position of a miner next to a pillar are also considered. Questions are also raised about the current interpretation of rib fatalities due to mining depth, with the indication being that mines operating at the greatest depths may actually have the most respectable rib fatality record among all mining depths. Additionally, a new method of considering rib exposure is developed. Based on the results, recommendations are made for future work. By gaining a better understanding of how particular factors contribute to rib fatalities as opposed to rib failure or stability, it is hoped that future efforts can be more precisely directed towards the desired outcome of fatality reduction.

Jan 1, 2014

"Chairman: Dr DeV. HarrisRapporteur: Mr A.H. MunroPapers:Corporate exploration strategies by MacKenzie, B.W.The Engel Simulator and the search for uranium by Griffiths, J.C. and Singer, D.A.The Chairman opened the session by tracing the changes which have taken place in the exploration field since the days of the lone prospector who relied upon his individual skills and to a large extent on luck. The deposits which now remain to be discovered are better covered and are of lower grade. A much greater team effort, involving geoscientists and engineers, is required. The gamble is thus much greater -not only are the probabilities of failure still significant but the consequences are more severe. A recent Canadian survey indicated that expenditures of between two and nine million dollars on regional exploration programs are required to locate one significant deposit.The Chairman went on to say that these facts have led companies to regard exploration as another form of investment and to treat it accordingly. This had placed exploration in the context of corporate strategics and structures, which was the subject of the first paper of the session.In introducing his paper, Dr B. W. MacKenzie said that the paper suggested a decision framework for exploration planning. Initially the environment is analyzed to define observable and relevant economic characteristics. The terms of reference for exploration planning and the appropriate allocation of capital and skills are then established in the light of corporate objectives and growth alternatives. With the aid of this information and in the light of profit and corporate risk criteria, exploration strategies can be selected.Dr MacKenzie went on to say that the usefulness of the concept and criteria outlined in his paper depended critically upon three characteristics of any particular economic environment, namely, the return resulting from an economic discovery, the unit discovery Cost and the probability of making an economic discovery. He then showed by means of a case history relative to the Canadian Shield and Cordilleran areas that these three characteristics could, in fact, be evaluated for regions with reasonable histories of mineral activity.The first contributor to the discussion of the paper, Mr Alfred Weiss, mentioned that his group had been involved in exploration modelling for some ten years and were thus particularly interested in the paper. He went on to say that they had experienced greatest difficulty with reconnaissance programs and that he sensed that these difficulties were also present with the methodology which had been outlined. Mr Weiss asked Dr MacKenzie how he would deal with such situations when no information was available but where there was the potential for both exploration and discovery. Dr Mackenzie agreed that the lack of information was a very severe limitation and said that at the present time his methodology probably did not provide a basis for breaking down the broad geological regions he considered into areas for further assessment."

Jan 1, 2014

By Tracy Shimmield, Philip Samar

"Metals have been mined as ores since pre-history but metal production has increased dramatically in modern times driven by expanding Global GDP. Metal ore mining produces large amounts of waste rock and mine tailings. Mine tailings are the wastes produced after extracting the desired metal from the ore. There are several ways of dealing with this waste, and Ritcey (2005) identifies the following possibilities, land-based storage, backfill to the mine, deep lake disposal and marine disposal. In Papua New Guinea (PNG), both Misima and Lihir Mines adopted the marine disposal option, releasing tailings through a submerged pipe onto the sea floor. This special case is referred to as Deep Sea Tailings Placement (DSTP) in which the tailings deposition is sufficiently deep as to be below the euphotic zone. The most important aspect of deep sea tailings placement is that the tailings are deposited at great depth where exchanges between the seabed and the surface layers are small. The first quantitative multidisciplinary study of tailings impact on the deep sea was carried out from 2006 to 2010 in Papua New Guinea. The physical, chemical and biological work carried out has placed PNG at the forefront of research into the assessment and management of deep-sea environmental impacts related to mining in PNG. The study has provided data which has led to a better understanding of the ecological and geochemical processes in deep water that accompany DSTP in PNG and provided baseline data on deep-sea ecosystems in a scientifically poorly known tropical ocean. Additionally, guidelines on best practice for DSTP have been developed Here we present geochemical data obtained from sediment samples from the marine environment surrounding Lihir and Misima Islands."

Jan 1, 2014

By J. Y. Xu

A mutant of Phanerochaete chrysosporium, which is capable of degrading lignin, was bred by ul-traviolet ray irradiation and this mutant strain shows high capability of degrading of lignite. The degradation ratio of original Yima lignite and nitric acid treated Yima lignite by this mutant are 37.6% and 51.62%respectively, whereas those by the original strain are 31.84% and 32.55% respectively. XRD and FTIR analyses of the lignite converted product show that its polymerization degree and average molecular weight are both greatly reduced. The content of the functional groups is also been altered.

Jan 1, 2014

By H. P. Kritzinger, T. C. Kingsley

Rotary kilns are used for a variety of mineral processing operations. Hatch makes use of a kiln model developed from first principles to evaluate designs for its clients. This tool has been applied to a variety of pyrometallurgical applications. This paper illustrates the application of numerical optimization techniques in combination with the kiln model in the interrogation of a generic iron-ore reduction process. The fundamental modelling concepts are explained, followed by a description of the optimization approach. The results show how the combination of the two methods, with modern computing power, can generate a large number of viable design and operating candidates.

Jan 1, 2014

By M. D. Budeba

Determining the efficiency of a surface coal mine operation is an essential activity, which can help in deciding on the optimal use of input resources, including effective capital allocation, in generating a desired quantity of coal of a specific quality. Mines operate today in challenging conditions, with diminishing reserves of high-quality coal, remote location of new coal deposits, infrastructure problems, environmental legislation, and the effects of climate. All these have an impact on the performance of a mine. Given such challenges, a company has to be technically efficient compared to other existing coal producers in order to generate profits. It can use the measurement of its efficiency to evaluate its productivity, benchmarking this against the best-performing mines and determining optimal variables in order to minimize slack and achieve the desired outputs. This paper discusses the use of Data Envelopment Analysis (DEA) in evaluating the efficiency of a surface coal mine supply chain for the coal export market. The supply chain is considered to be composed of subprocesses that are modelled as a multistage system. Numeric examples will be used to illustrate the application of DEA.

Jan 1, 2014

Research on alternative lixiviants for gold is ongoing; however few people have looked at complete flowsheets. Alternative lixiviants are typically applied at concentrations 50 to 100 times those required for cyanidation. The higher concentrations make lixiviant recycle a vital part of the process. In addition it is no longer feasible to rely on lixiviant destruction to produce lixiviant free clean water for recycle to the comminution circuit. Ausenco has worked with Barrick to integrate reverse osmosis into the thiosulfate RIL processing flowsheet that forms the basis of the plant upgrade currently being constructed at Barrick’s Goldstrike autoclave facility.

Jan 1, 2014

By Soumendra Basu, Uday Pal, Yang Yu, Srikanth Gopalan, Karl Ludwig, Deniz Cetin, Jacob Davis

"A limiting factor for Solid Oxide Fuel Cell (SOFC) performance is the oxygen reduction reaction (ORR) at the cathode surface. Changes in the surface composition and structure on annealing at 800°C has been studied, since these can influence the ORR. Idealized single crystals of cathode materials La0.8Sr0.2MnO3 (LSM) and La1-xSrxCoyFe1-yO3 (LSCF) were grown as heteroepitaxial thin films on lattice matched single crystal substrates. Changes upon heating the films to operating temperature and pressures were characterized using various synchrotron x-ray techniques. Total Reflection X-ray Fluorescence (TXRF) measurements, which probe compositional changes, were made at high temperature in real time. The LSM surfaces were found to develop manganese enrichment when heated. Highly strontium doped LSCF were found to develop strontium-rich surfaces. HArd X-ray PhotoElectron Spectroscopy (HAXPES) was used to investigate the electronic structure of the materials. Highly strontium doped LSCF precipitates a surface strontium phase that contains both oxide and carbonate contributions.IntroductionSolid oxide fuel cells (SOFCs) are chemical to electrical energy conversion devices that could potentially reshape how energy demands are fulfilled. SOFCs have a potential efficiency over 70%, fuel flexibility, low emissions, and low degradation over long time scales. Commonly, SOFCs are operated at high temperatures (above 800°C). At these temperatures expensive housing is needed to contain an operating stack as well as coatings to contain the oxidation of the metallic interconnects. Lowering the temperature of an operating device would allow for more conventional materials to be used, thus lowering overall cost. Understanding the reaction kinetics of the oxygen reduction reaction at the surface of the cathode is vital to designing a system that will perform well at lower temperatures. A commercialization goal is to reduce operating temperatures without sacrificing performance.In order to exploit the advantages of SOFCs, an understanding is needed of the surface chemical states of cations on the surface of the cathode and how this relates to the oxygen reduction reaction (ORR):"

Jan 1, 2014

By WenCai Li, Yong Ren, Shuai Niu, Xin Hong

"Temperature measurement is very important in metal smelting process. Many devices are used to realize non-contact temperature measurements. Compared to conventional thermocouple, infrared temperature measurement has it's unique advantages. However, using an infrared temperature measurement at the top of the furnace can not obtain the desired optical signal because of disturbance from slag layer, high-temperature gases and other effects. A real time thermometry system with dual-wavelength radiation was presented to get optical signal emitted from molten metal through bottom-blowing nozzle. Taking into account the advantages and disadvantages of bottom-blowing devices, a MHP (Multiple Hole Plug) bottom-blowing device was used, through which the optical signal was transferred to the infrared thermometer by use of optical fiber. After conversion and analysis in real-time, the result was displayed and recorded in computer. After calibration, it could be a good predictor of temperature trend in a metallurgical process. IntroductionAt the refining stage of steelmaking, in order to achieve predetermined chemical composition and temperature, high-temperature molten steel is refined in a furnace such as converter. Because the refining process involved with chemical components and reaction velocities in the furnace rely on the temperature of steel, it is necessary to know the temperature accurately in real time during the process. And temperature measurement is also helpful for the end-point judgment. The temperature in the refining process changes quickly, for instance, in a converter, 300t molten steel is processed in only about half an hour.At present, traditional way of temperature measurement is using a thermocouple probe mounted on a lifter called a sub-lance. The thermocouple is immersed in molten steel and its temperature is measured during the short period until the thermocouple is fused. Accurate and reliable temperature can be obtained by this method, but in consideration of the discontinuous measurement and the costs, missing the end-point temperature may sometimes occur.According to the above background, a method in which a temperature-sensing element such as a thermocouple is immersed directly in molten steel is not suitable for the continuous temperature measurement because materials having such stability are not available. Therefore, radiation thermometry is promising. There have been some reports on radiation thermometry through an observation nozzle through the bottom or side of a refining furnace [1, 2]."

Jan 1, 2014

By I. I. Maximov

The paper describes the results of studies performed with a view to develop an improved technology for processing high-grade massive and cupriferous ores of the Talnakh deposit, the main valuable components being nickel, copper and PGM. The studies? main task was production of nickel concentrate with nickel content of approx. 15%, nickel recovery being as high as possible. The studies were performed on two ore samples. One sample was a mix containing high-grade massive (78%) and cupriferous (22%) ores with nickel content of 1.93% and copper content of 3.6%; the other sample was a mix of high-grade ores with nickel content of 2.25% and copper content of 3.72%. Main ore minerals were copper sulfides ? chalcopyrite and cubanite, their total content being 10.5% ~ 11%, pentlandite (5.2% ~ 6.1%) and pyrrhotite (36.7% ~ 42.9%). Influence of grinding media on pentlandite and pyrrhotite separation results, achieved through combined use of triethylenetetramine (TETA) and sodium sulfite (SS), was also investigated. It is shown, that combined application of TETA/SS in the ratio of 1:2, permits to grind products in metal mill (mild steel) with metal balls (mild steel), achieving results that are similar to those achieved by means of grinding in inert grinding media with TETA/SS ratio of 1:1. Application of the developed technology provided for production of high-grade nickel concentrate with nickel content of 14.7% ~ 15.6%, nickel recovery being 76 % ~ 77%. Earlier experiments performed on the above mentioned ore mix permitted to produce nickel concentrate with nickel content of 10%, nickel recovery being 75.9%. Consequently, nickel content was increased by 4.7% ~ 5.6%, and a higher nickel recovery was achieved. The paper also describes metallurgical results related to nickel, copper and PGM with regard to all processing products.

Jan 1, 2014

By Tuomas van der Meer, Jukka Tanninen, Annukka E. Mäkinen, Mika Martikainen, Laura M. Nevatalo

The mining industry consumes huge water volumes and the waste streams typically contain sulfate, which has caused problems to many operations around the world. Discharge of sulfate to fresh waters is being restricted as the sulfate load increases salinity and causes problems when sulfate is reduced to toxic H2S by natural bacteria. To reduce fresh water consumption, internal water recycling had become a necessity in metallurgical processes. However, the recycling causes accumulation of sulfate and other components in water, causing problems to process performance and increases scaling in piping and equipment. Few technically feasible water treatment processes exist in the market that can be applied to decrease sulfate concentration below gypsum saturation level: biological sulfate reduction, membrane separation, ion exchange, evaporation and chemical precipitation. Some of these technologies are effective for treating wastewater, but there is typically a highly concentrated sulfate fraction left requiring still further treatment. Outotec has developed a sulfate removal solution, Outotec Ettringite process, which allows flexible control of residual sulfate concentration, thereby opening doors for increased water recycle within processes and control of the sulfate in discharged waters. In this article the results and benefits of this novel process along with examples of operating costs are presented.

Jan 1, 2014

By Weiran Zuo, Narayan Krishnan, Frédéric von der Weid, Emmy Manlapig, Fengnian Shi, Klaas van der Wielen

Laboratory study has identified a new application of high voltage electrical pulse technology for pre-weakening ores. In recent years, the Julius Kruttschnitt Mineral Research Centre (JKMRC), Newcrest Mining and SELFRAG AG have conducted joint research in validation of pre-weakening of SAG mill feed through the pilot scale tests and comminution circuit simulations. Ten tons of SAG mill feed with a top particle size 150 mm were tested with two pilot scale SELFRAG machines installed in Switzerland. A simulation study using JKSimMet software was carried out to find where the high voltage pulses pre-weakening technique can be best applied in a gold-copper ore comminution circuit, based on the data of the pilot scale SELFRAG tests. A novel comminution circuit was designed, which incorporated SELFRAG to pre-condition part of SAG mill feed (9.5 to 150 mm) and to treat the circulating SAG mill pebbles. The high voltage pulse technology effectively reduced the amount of ‘critical size’ particles in the SAG mill and pre-weakened particle strength for grinding. Attributing to the nature of bi-modal size distribution and the significantly reduced F80, the simulations showed that the SAG mill had spare capacity to process part of hydrocyclone underflow from the secondary ball mill grinding circuit. The simulations indicated that the novel comminution circuit had the potential to remove two MP1000 pebble crushers and one 10 MW ball mill from the existing 2000 t/h grinding circuit. A 5 kWh/t energy reduction by adopting the novel comminution circuit in a gold-copper operation may be realized. This would result in substantial savings in operation costs.

Jan 1, 2014

By Robert Hopler

On June 13, 1912, the final decree of dissolution of the DuPont explosives trust was handed down, and the resulting new companies began operating at the beginning of the new year. The property assets granted to (or retained by) the companies were as follows:

Jan 1, 2014

By D. R. Nagaraj

The traditional (popular) approach to reagent development and optimization, which has become entrenched in both research and practice for many decades, is highly reductionistic, incremental and costly, does not produce robust chemical solutions, and is not sustainable. There are also several other key drivers and changes in the mineral industry that clearly warrant a new approach. In response to these, an intense effort was made at Cytec over the past fifteen years to develop a meaningful, efficient, and sustainable approach to develop new reagents and robust chemical solutions in mineral separations. This effort culminated in three important outcomes: a) development of the holistic approach, called FLOTATION MATRIX 100? process, b) novel reagents, and c) enhanced application knowledge for reagents. In this paper, the efficiency, utility and power of the holistic approach will be demonstrated with examples using both existing and new reagents in the processing of Cu-Au, Au and Cu-Mo ores.

Jan 1, 2014

By Hamid-Reza Manouchehri

"Sustainability calls for maintenance, rational use and enhancement of natural resources as well as balance consideration of ecology, economy, and social justice. The challenges in mining industry call for a sustained global effort using the leverage of available technologies and emerging new technologies. The industry uses significant amount of energy with the highest portion in comminution. To conserve energy, attempts have been made to improve the efficiency of the conventional crushing and grinding equipment. Nevertheless, the new and energy efficient comminution technologies are favorable through a longer term strategy. Since crushers are more energy efficient than mills, it is logic to conduct part of milling, in the crushing stage. After years of research and development, Sandvik introduces a new crushing technology, VibroconeTM, to change traditional crushing concepts. The new crushing device is able to crush and grind particles with a higher reduction ratio, more than two fold, than that of conventional crushers. By implementation of the new technology, a suitable feed size for milling can be provided to conserve energy as well as media and liner consumption, to reduce milling circulating load or increase mill capacity. There are other benefits associated with this machine, one of them being providing a higher surface area. This paper discusses the performance of the machine and its applications for comminuting different ores."

Jan 1, 2014

By R. Lestari

Newmont Batu Hijau operates with an accelerated mining rate to optimize life of mine (LOM) project economics. This results in a portion of ore mined being stockpiled for reclaim and processing throughout, and at the end of mine life. LOM economics can be further enhanced by preserving stockpiled ore value by mitigating oxidation effects. A detailed stockpile ore oxidation study was conducted to: ?? Develop a practical understanding of how oxidation affects ore value; ?? Determine how oxidation rate can be controlled, and; ?? Determine how oxidation effects can be mitigated to preserve ore value. The result of the study is a stockpile management strategy that significantly reduces oxidation related losses and, implementation of that strategy within practical constraints. Implementation includes installation of Controlled Potential Sulfidisation (CPS) flotation to facilitate oxidised sulfide copper recovery and, recovery of dissolved copper from stockpile drainage solution into saleable product. This paper describes the study results including managing and predicting stockpile oxidation with time, monitoring performance of implemented CPS flotation and recovery of dissolved copper from stockpile drainage. These are essential elements of successful long term mine operation in Batu Hijau.

Jan 1, 2014

By G. W. Zhang

Ultra-fine Stirred Mill is a kind of high energy efficient equipment for ultra-fine grinding, and has been the mainstream equipment in the submicron powder and slurry industry. This paper mainly describes flow-field numerical simulation of the three popular ultra-fine grinding mills: (respective-ly as) Disc Stirred Mill, Pin Stirred Mill and Spiral Stirred Mill, by means of the software Computational Fluid Dynamics (CFD). In the flow-field numerical simulation, the velocity gradient, shear rate dispersion of the flow-field, the viscosity dissipation rate were analyzed with CFD. It is discovered that Pin Stirred Mill has the highest velocity gradient in circular directions and the most homogeneous distribution of shear rate among the three. Flow-field numerical simulation provides a new way (and means to) for the parameter optimization design and project enlargement of Ultra-fine Stirred Mill. The experiments were also carried out, the results are consistent with the results of the simulation analysis. For example, in GCC grinding experiments under the same conditions, the specific energy consumption of Pin Stirred Mill with 3600L in volume is 15%~17% less, and its processing capability is 13%~15% better than Disc Stirred Mill. Now with its optimized structure and excellent performances, more than ten sets Pin Stirred Mill with 3600L in volume have been used in industrial production in Shandong, Guangdong and Hunan province.

Jan 1, 2014

By T. Lang

Clay sorbents from the North Bohemian Brown Coal Basin represent important but still some-what neglected accessory raw material. Submitted paper is concerned with relation between mineral structure, sorptive efficiency and reclamation exploitation of these rocks. Characters and localities of main clay sorbents from the North Bohemian Brown Coal Basin are shortly evaluated in an introduction. In next part, methodology of mineralogy survey for these accessory raw materials is stated, it is based on diffract analyse with D 5000 Siemens X-ray diffracto-meter. At the conclusion results are stated of mineralogy analyses from several clay sorbents. The determination of the zeolite and montmorillonite localities was accentuated. The paper presents also possibilities of practical clay sorbents utilization, especially by reclamation works.

Jan 1, 2014