Search Documents

By R G. Moreby

The purpose of this paper is to provide the rationale for decision making when considering the use of three heading gate roads in Australian underground coal mines.There are currently 30 underground longwall mines in Australia with all but two employing two heading gate road longwall layouts. The volumetric capacity of these two heading ventilation circuits is evidently viable in typical block lengths and in low to moderate gas regimes. However, in gassier regimes, potential longwall production rates of 10 Mt/a, and or where block lengths are being extended to well beyond historical norms, a conventional two heading U circuit may not be adequate. Other than seam gas emission, block length and production dependent heat loads together sealed area management requirements also have to be considered.The two mines currently employing three heading gate roads have the opportunity to revert to two headings at any time but, based on operational experience to date, have not done so due to the consequential reduction in gas management capacity and lower production rates associated with gas delays and limitations on tailgate access.Although there are a number of alternative two heading longwall circuits available and employed worldwide, the custom and practice of promoting inert goaf atmospheres in most Australian coal mines to mitigate the risk of catastrophic gas explosions and spontaneous combustion often prevents the use of gas loaded bleeder systems. In this respect, Australian underground coal mines may be considered the safest in the world.The current situation is that three heading gate roads have been proven successful in Australian conditions, albeit at additional cost, where two heading ventilation circuits cannot manage net seam gas emission to the ventilation system at the production rates required. In this respect, a further important driver for decision making is the short to medium term value of CO2-e emission taxation in Australia.CITATION:Moreby, R G, 2013. The rationale for use of three heading gate roads in Australian underground coal mines, in Proceedings The Australian Mine Ventilation Conference , pp 13-26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By A S. Derrington

This paper describes a hybrid ventilation system, which uses secondary fans that also act as de-facto primary fans to extract fresh airflow from the mine intake raise system. Also discussed are the associated problems such as uncontrolled recirculation, inadequate decline airflow, fire safety issues, prolonged blast fume clearance times, high air temperatures in main access routes, neutralisation of mine air cooling by heat from secondary distribution fans, increased ventilation system complexity, reduced flexibility and high pressure differentials (which cause safety issues with personnel access and reduce secondary ventilation system performance).Practical suggestions are provided on options to avoid these problems listed.CITATION:Derrington, A S, 2013. A critique of the push-pull hybrid ventilation system, in Proceedings The Australian Mine Ventilation Conference , pp 73-78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By D Roughsedge, J van der Sandt, L van den Berg

Axial flow fans are commonly used as auxiliary fans in underground mines to supply air to development headings. As diesel dilution requirements increase the fans used in conjunction with ventilation bags are becoming larger in diameter to move greater quantities of air over greater development distances. It is not uncommon for mining operations to sometimes use a number of these larger auxiliary fans with high airflow capacity in parallel as primary fans for the operations. These primary fan stations are often considered temporary installations and the fan selection and fan station design is rarely optimised. These temporary installations may become permanent resulting in an inefficient or unreliable primary ventilation system. A recent study looked at the likely causes of multiple primary fan failures at one operation with axial fans installed as primary units where the fan selection and fan station aerodynamic design was far from optimal. This paper explores some of the typical mechanisms of failure such as high pressure stall, unbalanced airflow, and fan tip speed as well as fabrication material. The paper proposes a number of good practise principles that should be considered during the design of a fan station. A second topic covered is the advantages and disadvantages of using different types of fans such as axial, mixed flow and centrifugal units. Here the concept of fan specific speed and its relevance to fan selection is discussed. Finally the paper quantifies the effect of using a high pressure auxiliary fan as a primary fan in a low pressure circuit, which may increase the mineÆs operation cost.CITATION:van der Sandt, J, van den Berg, L and Roughsedge, D, 2013. Practical considerations when using auxiliary axial flow fans as a primary mine fan, in Proceedings The Australian Mine Ventilation Conference , pp 63-70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By ZáWang, F Hungerford, T Ren

Operations in an underground drill site have to co-exist within the mineÆs ventilation and operational system. The space requirements of a drilling operation have to be adapted to the limitations provided in available site space, which is usually defined by standard mining operations and geotechnical influences. These limitations affect borehole design, equipment positioning in the site layout and possible interactions with mining equipment and services such as water and power supply.The ventilation requirements for drill sites and the means employed vary with depth of the site, space and likely presence of gas. All drilling operations provide a particular service for the mine and in each case, drilling must operate in a manner which controls all gas, water and cuttings returning from the borehole. The various standpiping systems employed have evolved under differing influences and must cater for conditions during and after the drilling operations.The influences that gas content, pressure and flow, rib stability, cleat direction, borehole length, potential water pressure and flow have on a mineÆs operation and ventilation systems have to be considered in the design of standpipe length, diameter and fittings. Past history has a strong influence on common practice while worst case effects of a possible in-hole event should be catered for.This paper describes the early drilling systems and their limitations in ventilation and gas management. The drill site dimensions and set-up are discussed in the context of roadway conditions, equipment layout, ventilation and logistics. The use of standpiping to control all returns from the borehole is illustrated by referring to likely scenarios in a drilling site to achieve the most effective sealed depth to accommodate the worst case possibility of intersecting high pressure gas or water during the drilling operation. Practices to allow gas drainage in the return airway of a panel are described.CITATION:Hungerford, F, Ren, T and Wang, Z, 2013. operational management of underground in-seam drilling sites, in Proceedings The Australian Mine Ventilation Conference , pp 43-48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By R G. Moreby, S Bluhm, FávonáGlehn, C Pascoe

Resolution Copper Mine in Arizona, USA, is planned to be a 2000 m deep panel cave mine with virgin rock temperatures exceeding 80¦C in rock with high crystalline silica content, resulting in a very challenging ventilation and cooling system design. This is one of the largest copper orebodies ever found and, with a planned rock production rate of 120 kton/day. The project is currently in its prefeasibility phase and the paper discusses features of the ventilation and cooling system design which includes multiple ventilation shafts with total primary ventilation flow of about 3000 m3/s and both surface and underground refrigeration plants producing more than 140 MW refrigeration capacity. The cooling system features large surface bulk air coolers chilling all downcast air supplemented by an underground secondary air cooler system and a chilled service water system. This will be a very challenging mine to ventilate and cool but this work has demonstrated that it will be technically achievable with the application of existing technology.CITATION:Bluhm, S, Moreby, R G, von Glehn, F and Pascoe, C, 2013. Life-of-mine ventilation and refrigeration planning for Resolution Copper Mine, in Proceedings The Australian Mine Ventilation Conference , pp 125-138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By S Viviers, G Ratner

Ventilation is part of all underground mine operations and is undertaken in order to introduce fresh, cool air to the workings and to remove stale, affected air. It is problematic to obtain efficient and accurate estimates of volume flow and static pressure in the installed operational configuration for the auxiliary axial flow fans.An empirical method was developed to estimate the static pressure and volume flow through a calibrated differential pressure port on axial flow fans. Prior to shipping, each fan is performance tested according to BS 848 (ISO 5801) to establish the fan performance curves. In addition to the standard required parameters captured to fully describe the performance, the differential pressure is measured across the fan rotor to enable correlation with the characteristic fan curve.The method was implemented on a ruggedised tablet PC platform. This compact platform is then used to calculate the volume flow rate from the differential pressure sensor measurement input via a USB port. The result is a real-time measurement of volume flow and operating point of the fan system. This can be used effectively in overall modelling of the mine auxiliary ventilation systems and calculation of system resistance could provide a health indication of the fan and duct system.CITATION:Ratner, G and Viviers, S, 2013. Underground auxiliary ventilation monitoring and diagnostic system, in Proceedings The Australian Mine Ventilation Conference , pp 57-62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Sandy Worden

Coal mining companies in Australia are managing the high-consequence risks across their operations more effectively by using an interactive online risk management system known as Riskgate Developed by the Minerals Industry Safety and Health Centre (MISHC) at the University of Queensland, Australia, Riskgate contains detailed information about 11 high-consequence risk areas (called topics in the system) for opencut and underground coal mines (Table 1). The existing topics are: fires; strata control for underground mining; ground control for opencut mining; tires; isolation; collisions; explosions and explosives; manual tasks; and trips, slips and falls. Every Riskgate topic is focused on coal industry activities (mining, processing, transport and storage). The scope includes mine sites, lease areas and mine infrastructure (mobile, fixed plant, field equipment, buildings, road and rail transport), and all aspects of the mine life cycle from design through to decommissioning. The topics uniformly recognize that a loss of control can result in injury or fatality, equipment damage, production loss, reputation loss and environmental damage. However, the priority focus for Riskgate is the safety of mine personnel.

Jul 1, 2013

By S. Khoshjavan

In this investigation, the effects of different coal chemical properties were studied to estimate the coal Hardgrove Grindability Index (HGI) values index. An artificial neural network (ANN) method for 300 data-sets was used for evaluating the HGI values. Ten input parameters were used, and the outputs of the models were compared in order to select the best model for this study. A threelayer ANN was found to be optimum with architecture of five neurons in each of the first and second hidden layers, and one neuron in the output layer. The correlation coefficients (R2) for the training and test data were 0.962 and 0.82 respectively. Sensitivity analysis showed that volatile material, carbon, hydrogen, Btu, nitrogen, and fixed carbon (all on a dry basis) have the greatest effect on HGI, and moisture, oxygen (dry), ash (dry), and total sulphur (dry) the least effect. Keywords coal chemical properties, Hardgrove Grindability Index, artificial neural network, back-propagation neural network.

Jun 1, 2013

By Samuel Frimpong

The preparation of graduate talent for the mining industry is a challenging process, given the multifaceted and complex array of decisions mining engineers make in discharging their responsibilities. As leaders, mining engineers must manage operations, lead project teams, mentor junior engineers, chart the technological directions of companies and deal with several organizations for maintaining the technical and economic feasibility of operations within strategic and tactical framework. Traditionally, the completion of the bachelor of science degree curriculum, with a minimum cumulative grade point average (CGPA), has been used as a graduation measure by Missouri University of Science and Technology (Missouri S&T). Companies have long realized the limitations of the CGPA for recruiting graduates because mining engineering is an applied engineering discipline. Company recruiters have sought to correct the limitations by factoring experience and behaviors into the selection process when recruiting knowledgeable and well-rounded graduates. In this paper, the authors introduce a new metric, which combines the current CGPA (knowledge) with experience and attribute (KEA) metrics to gauge the job readiness of graduating engineers. The KEA metric, also called the job-readiness factor (JRF), is the sum of K (50%), E (30%) and A (20%). The KEA process has been applied to a graduating class in Missouri S&T to demonstrate the value of the new metric system. The results show a fairly positive correlation between CGPA and the KEA metric, with a coefficient of determination of about 70%. Overall, the KEA metric system provides a better picture of the capacity and job readiness of graduates entering the workforce.

Jun 1, 2013

By D. B. Rebuli

Seismic networks in deep gold mines of South Africa are often planar owing to the tabular geometry of the orebody and, therefore, the mining infrastructure. Consequently, seismic event locations are poorly constrained in the direction perpendicular to the reef plane, and symmetrical locations above and below the reef plane may fit the observed data equally well. This problem may be resolved in situations where the strata above and below the reef plane have significantly different seismic velocities, which is the case for the Ventersdorp Contact Reef at Kusasalethu mine (previously Elandskraal, the amalgamation of Deelkraal and Elandsrand). A location method using a layered location model that takes into account the velocity contrast between the layers was tested. Observed direct- and head-waves were used to determine the velocity bounds of the P-wave velocities in the two-layer model. The data-set was also used to find the best P- and S-wave velocities for the two layers by grid searching over a range of velocities and minimizing the sum of the travel-time residuals. The results from the grid search and those from the calibration of velocities using direct- and head-waves give similar P-wave velocities for each of the two layers. A second set of seismic events was then relocated with this layered model and locations closer to reef were found. This simple layered location method goes some way to reduce the reefperpendicular location errors for Kusasalethu mine in particular. Keywords mine seismology, velocity model, location methods.

Jun 1, 2013

One of the critical challenges facing the mining industry ? and not just in the United States ? is the looming labor shortage. A significant percentage of the industry?s professional workforce is, well, getting old, and many will be retiring in the next 10 years or so. This is not a new issue to the industry. It has been discussed at various industry meetings and conferences for many years. How does mining, with its largely negative public image, attract young people to mining schools? And, equally important, who is going to teach them? Mining schools, what?s left of them in the United States, are beginning to lose qualified faculty to retirements, and no one is available to replace them. SME addressed this issue during the keynote session at its annual meeting in February in Denver, CO. This year?s theme was ?Mining: It?s About the People.? Despite a blizzard that blanketed the city on the day most attendees were to have arrived, the meeting still attracted a record 7,202 people. And the accompanying exhibit sold 822 booths, also a record. The U.S. Department of Energy?s National Energy Technology Laboratory contracted with the National Academies? National Research Council to complete a study concerning the availability of skilled workers to meet the energy and mineral security requirements for the United States. The National Research Council, in turn, asked SME to collect and analyze workforce trends in these industries. The result of SME?s analysis is the report ?Emerging Workforce Trends in the U.S. Energy and Minerals Industries.? It is available on the SME website, www.smenet.org. Click on Government Affairs. While the report did not paint a completely dismal picture, there were some disturbing results. It concluded that within 20 years there will not be a sufficient number of skilled professionals to satisfy the labor demand. That said, the report said that most of those positions would likely be filled. However, the U.S. mining will go through a period of time when the workforce will be made up of very young and senior workers.

Jun 1, 2013

By Rob Scott

Making a difference with Zinc & Health Two billion people do not get enough zinc in their diets. Every year 450,000 children die from complications arising from zinc deficiency Our Zinc Alliance For Child Health partnership with CIDA and Micronutrient Initiative, our involvement with UNICEF through the IZA and our partnership with BASF are gaining wide recognition. Sustainability at Teck ? Integrating into our Core Business Strategy Our strategy Long term goals Our approach Managing risks and finding opportunities Our progress Early reports Moving Forward Metrics and indicators

May 1, 2013

By G. Kallfa P. Geo

Exploration at both Greenfields and Brownfields stages entails business risks of different nature and success rates. Greenfields exploration is exceedingly assumptive and the success rate of exploration or return on investment is low because exploration is an inherently risky business. Brownfields exploration on the other hand is less risky, as the geology is better understood, but generally speaking since the larger ore bodies close to surface have already been found the return is lower. In addition, most exploration at the Brownfields stage is generally more expensive due to extensive use of drilling. Surface geology mapping and expensive drilling have been key technical contributors to most exploration programs over the last two decades. However, as client expectations, logistics, target depths and complexity of exploration programs increase, there has been a growing emphasis on using geophysical techniques to complement other methods. Integration and optimization of various geoscientific disciplines is becoming more important in successful exploration programs of the future to reduce exploration risks, successful integrated exploration requires putting reliable geophysical parameters and correspondent petrophysical property contrasts into an assumed or conceptual geological model. This paper discusses a new multi-parameter geophysical methodology finalized in a unique conceptual geologic model which can be used either as a root model in grassroots exploration or as an efficient tool in Brownfields exploration to successfully find satellite orebodies of almost any size. The application of a new multi-parametric geophysical approach to Brownfields exploration is illustrated with examples from Manitoba, including a past producing nickel sulphide deposit in Lynn Lake and the Reed Copper deposit, currently in development.

May 1, 2013

By Chris McBean

Due diligence mistakes ? lost opportunity ? High profile write-downs and cost overruns ? Result ? tight market for financing ? Implications for due diligence ? need to get it right ? maybe only one chance ? Where should focus be?

May 1, 2013

By Eric D. Monrad

Supply chain simulation modeling is taking on a more prominent role in mining project planning and decision making. Transportation costs for the supply chain can form a significant component of the overall cost to provide product to the end customer. In recent years, computing power has increased, simulation software has advanced, and simulation specialists have become even better equipped to provide sophisticated analysis and recommendations. This has led to a virtuous cycle of owners expecting and supporting data-driven analytics, which drives further advancement. This paper discusses developments in supply chain planning and two case studies from recent simulation modeling analyses.

May 1, 2013

By Christine Hansen

?Kiss my Asteroid? Unofficial Title Human life is tied to minerals It?s worth noting that: The living human body consumes minerals. The minerals we take in multivitamins show the close linkage between human beings and mineral resources. Unlike tourism or specialized manufacturing, a human being could not live without mineral consumption. Minerals and their consumption is a tangible part of human life.

May 1, 2013

By José J. Suárez

Abstract: Globally, the mining industry is expected to face the following challenges through 2020: 1. Sustaining growth amidst fierce competition 2. Containing cost increases and managing through the cycle 3. Attracting and retaining talent 4. Managing environmental concerns and improving sustainability 5. Managing volatility risks in commodity markets Our experience and research reveals that the higher performing global miners are adopting many of the following strategies: (1) Adopt a Global, Agile Operating Model (2) Be the Developer of Choice (3) Drive Capital Efficiency (4) Be the Employer of Choice (5) Integrate the End-to-End Business Model (6) Move to the Virtual Mining Value Chain This paper/presentation will provide data obtained through research on five (5) challenges facing the mining industry, and on the six (6) strategies that high performing global miners are adopting.

May 1, 2013

By Vic Briccardi

Energy Management Challenges The Holistic Standard to Energy Management Energy Management Information System (EMIS) "Best Practices?: Energy Management Maturity Curve De Beers Canada Profile & Mine Locations Significant ROI Driven by Real-Time Energy Visibility Mining Energy KPI?s Summary: What Does EMIS Deliver? Q&A Session

May 1, 2013

By Dan Nower

Machinery Health Monitoring of Shovels MINExpo 2012: Caterpillar announced the largest Electric Rope Shovel, capable of 120 short tons The next day, JoyGlobal (P&H Mining) ?one-upped? CAT, introduced a shovel capable of 135 short tons Large Concern: breakdown (unplanned outages) of one machine will be more disruptive to production

May 1, 2013

By Muhammad Zaka Emad

ABSTRACT: Sublevel stoping mining methods with delayed backfill employs cemented rockfill (CRF) as a backfill material. It is used in underground mines to achieve ground control and reduce wall slough. In addition CRF serves to reduce development waste and provides a working surface for mining the upper levels. Efforts to optimize CRF practices have been published. This paper presents a detailed review of CRF practices in open stoping mining systems with reference to case studies. A new methodology is suggested in a simple stepwise approach, which can be adopted for site specific conditions. The need of laboratory testing and quality control program is discussed based on the published literature.

May 1, 2013