Search Documents

By C. I. Walker

Field tests at a number of large mineral processing operations have been undertaken to better understand the wear life impact of different aspects of pump design, materials of construction and maintenance procedures. Data are presented for wear rates, and typical result variability is explored. To improve the availability of pumping equipment in a milling circuit it is not only important to improve the wear life, but also reduce the variability in the wear life of components so that the incidence of premature failure is lessened. Localised gouging wear due to flow separation and turbulent eddy formation is often the point at which part-holing occurs. A number of improvements to the design of pump impeller and throatbush (suction side liners) to reduce the localised gouging wear are outlined. Also, results are presented on the use of composite materials (mix of metal, rubber and ceramic) for throatbush materials to protect specific areas against wear.

Jan 1, 2012

The Autogenous milling of ores holds an increasing attraction as the focus moves towards reducing energy usage, both direct and embodied in grinding media. However, most of the early AG mills were converted to SAG for improved stability and increased throughput. This imposes a huge penalty in steel grinding media consumption. The LKAB iron ore operations in Sweden process highgrade magnetite through fully-autogenous milling lines to a final product P80 of about 45µm. The outcomes of P9O AMIRA research surveys, covering a wide range of mill fillings and throughputs and with different feed blends, are presented. Insights are provided on operational strategies, opportunities, the influence of feed size control and balancing the blend of competent gangue and softer magnetite. Areas of importance in the successful operation and control of energy-efficient autogenous circuits are highlighted.

Jan 1, 2012

By L. A. Cornish

Pt-based alloys for high-temperature applications in aggressive environments have been under development for over 10 years, and are targeted to be used as either as bulk, or as coatings. The alloys comprise Pt, Al, Cr, and Ru, and the microstructure has been improved by composition to a best possible analogue of the nickel-based superalloys, which these alloys could partially replace. This was necessary because the previous best alloy had a strengthening precipitate volume proportion of only approximately 40 vol.%, whereas the nickel-based superalloys have around 70 per cent, and a lower volume would mean that the strength would not be the best that could be obtained. The microstructures were assessed using electron microscopy, and have been related to the alloys? hardness values. The current microstructures are much more like those of NBSAs, with a high proportion of the strengthening ~Pt3Al precipitates. Since the samples have to be small (platinum is expensive), hardness has been used as an indication of strength. Nano-indentation studies showed that the hardness and Young?s modulus were higher for ~Pt3Al than the (Pt) matrix. More extensive oxidation studies have been undertaken on the previous optimum sample, and the effect of cooling rate after heat treatment has also been ascertained. In addition, the samples were studied after different heat treatment times, and cross-sections were made in order to characterize the alumina scale that formed. The oxide scales of Pt-11Al-3Cr-2Ru (at.%) up to 100 h exposure did not spall, and were at least as good as those of the ternary alloys. There was no discernable Al depletion zone in the substrate, although it could have been at a greater depth than thickness of the samples studied. Further additions to the Pt-Al-Cr-Ru alloys have been studied, to increase the melting temperature as well as to reduce the platinum content without compromising the properties. Reduced platinum content would have the benefits of reduced density and cost. The target elements include vanadium and niobium, of which vanadium is of special interest, since it is a South African product. Before these additions could be made, phase equilibria studies were undertaken so that the maximum addition could be ascertained, and also to check any possible ternary phases, which could be deleterious. Work on the Pt-Al-V system revealed a ternary phase, ~V27Pt54Al19 (at.%), which has a eutectic reaction with (Pt). The maximum V addition is likely to be around 15 at.%, otherwise ~Pt3V or the ternary phase will form, and not the required (Pt)/~Pt3Al phases.

Jan 1, 2012

By Reza Kamali, Mohsen Bashiri, Hadi Fanisalek

"Nomenclature: A: area (m2), C: heat capacity (WIK), cp: specific heat (J/Kg K), d: internal tube diameter (in), F: correction factor for multi-pass and crossflow heat exchanger, h: convective heat transfer coefficient (W/m2K), k: thermal conductivity (W/mK), L: length (m), m: mass flow rate (Kg/s), W: flow rate, N: number, Q: heat rate (W), R: thermal resistance, T: temperature (°C), U: overall heat transfer coefficient (W/m2K), ;1,,P: pressure drop (Pa), ;1,,T: temperature difference (°C), p: density (lb/ft3), N: number of tube passes, U,: velocity in tubes, iJh: head loss in feet of flowing fluid, Up: velocity in the pipe leading to and from the heat exchanger (ft/sec), µ: viscosity ( cp ), Llpf frictional pressure loss (psi/l 00 equivalent ft of pipe) Subscripts: b: baffle, c: cold, cf counter flow, ex: exchanger, f: fouling, h: hot, i: inlet-inner, ib: inlet baffle, lm: logarithmic mean, m: mean, o: outlet-outer, s: shell, t: tube, w: wall AbstractThe main bottleneck for primary aluminum production industry is dealing with a huge amount of input energy. The fact is that part of provided energy to aluminum production smelters will be lost as waste heat and it never used for aluminum production. One part of waste heat is escaping from the potroom exhaust gases, which was studied for possible recovery in a desalination plant to produce distilled water and the paper was presented in 2011 TMS Annual Meeting. However, it was shown that waste heat recovery plant to produce distilled water is highly profitable but the main fact is that the exhaust gases from potroom are highly corrosive, abrasive and dusty. The main challenge for desalination plant construction, which is using aluminum smelter exhaust gases as the main heat source, is the highly corrosive environment that makes the situation difficult and complicated for equipments design and plant construction. In this paper, we are trying to study a detailed investigation regarding the heat exchangers fouling, corrosion in heat exchangers including heat exchangers' material, how often we need to shut down the plant for maintenance or cleaning, and plant thermal efficiency with considering fouling."

Jan 1, 2012

By D. W. Alexander

Researchers from the U.S. Office of Mine Safety and Health Research (OMSHR) of the U.S. National Institute for Occupational Safety and Health (NIOSH) completed field trials during coal mine rescue contests using simulated gas detectors in place of placards. The gas monitor simulator (GMS) devices replaced static, paper placards to deliver gas concentration data. Eleven teams were observed during the field contest, which was approved by the Mine Safety and Health Administration (MSHA). GMS devices were given to three team members (the captain and both gasmen). Observation of teams revealed that team members changed behavior by acknowledging and sharing information more often while using the GMS. As a result of this research, it has been demonstrated that under the existing contest format, the newly developed GMS device may be used with no adverse impact on team contest performance. Furthermore, when GMS technology advantages are used, contest realism is improved. In the future, competency assessment may be incorporated.

Jan 1, 2012

By C. A. Nogueira, F. Margarido

"A research work has being carried out annmg at evaluating the possibility of treating simultaneously several electrochemical systems of spent batteries using the same process, in order to overcome the high costs and difficulties of selective collection and sorting. Zn-Mn02 systems, representing more than 75% of portable battery market, shall be treated in dedicated processes. The treatment assessment using a single hydrometallurgical process of the other major systems (NiCd, NiMH and Li-ion), having Ni and Co as main metals, was the aim of the research work here reported. Sulfuric acid leaching was demonstrated to be adequate for dissolving more than 90% of the metals of interest contained in batteries. The subsequent separation of metals by solvent extraction, using organophosphorous extractants like DEHPA and Cyanex 272, allowed the production of pure solutions of rare earths, cadmium/manganese, cobalt, nickel and lithium, enabling their further recovering.IntroductionRecycling is the best approach for end-of-life management of spent batteries mainly by environmental reasons but also motivated by resources conservation and, in some cases, by economic profits. Most relevant electrochemical systems of portable cells are Zn-Mn02 (ZMB, alkaline and saline), nickel-cadmium (NiCd), nickel-metal hydride (NiMH) and lithium-ion (LIB). These batteries are collected, sorted and usually treated separately, applying for pyrometallurgical or hydrometallurgical technologies, the former being the most common.Several processes have been developed and some of them industrially applied, as described in some available review papers [l, 2]. In Europe for ZMB systems the oldest processes are Batrec [3] and Citron [4]. Although having differences in details, both are based on pyrometallurgical recovery of zinc by distillation, in metallic or oxide forms, being manganese retained in the slag together with iron. Hydrometallurgical alternatives are also available, like Zincex [5] and Recupyl [ 6] processes, both using sulfuric acid solutions as leachant. The application of the existing technologies to battery recycling, instead of using dedicated processes, is other alternative already tested, being the Waeltz furnace or the Imperial Smelting some examples."

Jan 1, 2012

By A. Taylor, J. Shelegey, H. Sullivan, J. Doucet

"Historically, performance at Vale’s Clarabelle Mill was measured by Mill throughput and Mill recovery. After the economic collapse in 2008, a series of reviews were performed to drive improvements in business efficiency. These identified that product quality (e.g., concentrate grade, variability in concentrate grade) had a profound impact on downstream processes and suggested that improved control of these parameters would generate the greatest value for the customer (the Copper Cliff Smelter) and the company (Vale). Consequently, a movement was initiated to transform the Mill operating philosophy to consider customer needs as paramount. Systems and strategies used to drive the transformation are described. In 2011, an unexpected furnace failure resulted in decreased capacity at the Copper Cliff Smelter. In response, a two-stage change in production strategy was developed at Clarabelle. The first stage was to modify the ore blend feeding Clarabelle so that the concentrate grade could be significantly increased with minimal impact on recovery. The second stage was a circuit modification to ensure the elevated concentrate grade could be sustained. Execution of the first stage was complete five days after the failure and the second stage was complete within 10 weeks. Steps involved in each stage are outlined and the overall benefits are presented.INTRODUCTION Clarabelle Mill is located in Copper Cliff, Ontario, Canada (approximately 350 km north of Toronto). The Mill treats copper (Cu) and nickel (Ni) sulphide ores. The primary diluents are pyrrhotite (Po) and non sulphide gangue rock (Rk). The process description of the circuits at Clarabelle is documented in the paper by Taylor, Doucet, Blanchette, Barrette & Lawson (2012) in this Proceedings and will not be repeated. The Mill treats ore containing Cu, Ni and platinum group elements (PGE’s) and produces two concentrates; a Cu concentrate and a bulk Cu/ Ni Concentrate (referred to as nickel concentrate). The Cu concentrate is sold to market while the Ni concentrate is thickened at the Mill and pumped to Vale’s smelter complex in Copper Cliff Ontario for further processing. Since commissioning in 1971, Clarabelle Mill has undergone many circuit changes to suit the changing needs and wants of our customers, both internal and external. The Mill processes ores of varying quality, based on mineralogy and size and until 2009 the Mill daily performance was primarily based on throughput. The second key performance indicator (KPI) of “good” or “bad” performance was quality of the concentrate and third; Mill metal recoveries. There were other plant level KPIs such as flotation feed grind size, slurry densities and mass flows to the separation circuit, but for the most part each day was good or bad depending on how many tons were processed through the Mill."

Jan 1, 2012

By Kenneth Maas

The Bureau of Mines devoted portions of the 1987-1988 field seasons to investigate the mineral aggregate industry in Juneau, Skagway, Haines, and Gustavus, Alaska, as part of the Juneau Mining District study. Statistics compiled for current suppliers include location, activity, reserve estimates, expected mine life, and types of commodities available. Each population center, except for Gustavus, is well endowed with suitable mineral aggregate to last at least 20 years. The Bureau of Mines quantified the mineral aggregate resource in many large potential sites within each area. Sampling, engineering and soil-index testing, site descriptions, deposit dimensions, and gold recovery information is described. Refraction seismic studies performed at three localities revealed gravel thicknesses in excess of 40 to 80 feet. In the Juneau area the Herbert/Eagle Rivers outwash area, East Fork Lace River. Antler/Gilkey Rivers, and Grizzly Bar (Taku Inlet) individually contain in excess of 60 million yd3 of excellent-quality aggregate with minor accessory gold credits. Haines is also well endowed with aggregate resources; large, quality deposits occur along and at the confluences of the Chilkat, Katzehin, Klehini, Tsirku, and Kicking Horse Rivers. Large deposits of granitic aggregate exist in the Skagway River and East Fork Skagway River.

Jan 1, 2012

By H. M. Lima, L. A. Gomiero, C. A. de Morais

ABSTRACT The Caetité-Brazil uranium facility produces approximately 400 tonnes U3O8 per year from an ore averaging 0.29% U3O8. The process steps are ore crushing, heap leaching with sulphuric acid, uranium separation and purification by solvent extraction (SX) with a tertiary amine, followed by stripping with a sodium chloride solution, precipitation as ammonium diuranate (ADU), and product drying. A change in the milling process is being evaluated to increase production and uranium recovery. Heap leaching will be replaced by conventional agitated tank leaching of the –590 µm ground ore slurry in a sulphuric acid medium. Replacement of the stripping reagent is also being considered.

Jan 1, 2012

By H. Sevim

Mining engineering curriculum has been discussed and debated in meetings and conferences, and opinions and recommendations have been published in the literature since the inception of the official degree-granting mining engineering program at the Columbia School of Mines in 1864. The deliberations have usually been heightened during the periods of boom-and-bust cycles experienced by the mining industry since the 1920s. Currently, the global natural resource industry is undergoing another cycle, called ?super cycle,? characterized by elevated prices for metals and other natural resources. The super cycle is occurring as a result of the large deficit between the global supply and demand for natural resources, due, in large part, to economic expansion and development in countries such as China, India and Brazil. Because of this cycle, there is a shortage of mining engineers in the U.S., Canada and Australia.

Jan 1, 2012

By Dao Su, Ganghua Fu, Xuling Chen, Yufeng Guo, Min Gan, Tao Jiang, Xiaohui Fan

"The sinter quantity and quality of limonite in the magnetite and hematite sintering models were studied and compared. For the sintering of magnetite, the results showed that the increase of limonite improved the permeability of sinter mixture, increased the sinter quantity and quality. The sinter strength and productivity were decreased when the proportion of limonite exceeded 50%. The appropriate proportion of limonite was 40%-50%. For the sintering of hematite, the sinter quantity and quality were first maintained at the same level thereafter declined, more obviously when the proportion of limonite exceeded 40%. The amount of calcium ferrite increased whose shape changed from acicular to leaflike and block gradually with the proportion of limonite increased from 0% to 80%.IntroductionWith the fierce competition of domestic and overseas iron markets in the twenty-first century, cheap ores such as limonite are used to be sintering raw materials to cut the costs of sinter and pig iron for steel making, and boosts the competitiveness of steel companies [1, 2]. In addition, as the reserve volume of hematite of high grade is reducing year by year, the usage amount of limonite in sintering are expanding in major domestic and international sintering plant [3, 4]. Sintering can be divided into two types, majoring in concentrates and fine ores, according to the different types of raw materials. The sintering characteristics of limonite in the two types above have been studied and compared in this paper, which makes a significant sense for the research of limonite sintering properties and guidance of ore proportioning in sintering plants."

Jan 1, 2012

By A. Iván, Patiño C. Francisco, Flores B. Javier, Peréz L. Miguel, Hernandez A. Juan, Trapála P. Norma, Salinas R. Eleazar, Rivera L. Isauro, G. Flores, U. Mizraim

"Tills work is related with the production of tiles using wastes from mining and metallurgical industry of Hidalgo State, as raw material. These wastes present a majority particle size (60 %), minor than 53 m (mesh 270, in Tyler Series) with the following composition; 70.01 % wt. of Si02, 12.82 % wt. of Ah03, 3.80 % wt. of Fe, 0.70 % wt. of Mn, 3.98 % wt. ofK20, 3.34 % wt. of CaO, 2.50 % wt. ofNa20, 0.04 % wt. of Zn, 0.026 % wt. of Pb, 56 grams per ton of Ag and 0.6 grams per ton of Au. In this work, the partial results and experimental conditions for the preparation of some composites to produce tiles are shown. The composite that offers the best results in productions of tiles was that with 66.67 % wt. of mining waste, 26.67 % wt. of red mud and 6.67 % wt. of black mud.IntroductionTo now, mining activities carried out during more than 457 years in Hidalgo State, Mexico; has lead a great volume of wastes; which can be classified into different types, having among the more common; Acid mining water, solid transport water, elements in radical form, abandoned minerals without processing and processing minerals wastes known as burrows, being these the most abundant in the region counting with an approximated volume of 110 million of tons, presenting a fine particle size that can affect population health during windy epochs [1 -4].Form metallurgical point of view, is well known that a fundamental characterization study it is necessary to know the viability of reusing or recycling of these wastes. According this, these residues can also be considered as raw materials in other economical activities, due its Si, Fe, AI, Ca, Na and P oxides contents, its mineralogy and the distribution of chemical elements in the primary and secondary phases [1,2,5,6]."

Jan 1, 2012

By D. P. Roberts

This investigation aimed to simulate the experiments performed by Nic Gay (Gay, N.C.1976. Fracture growth around openings in large blocks of rock subjected to uniaxial and biaxial compression. International journal of Rock Mechanics and Minining Sciences and Geomechical Abstracts, vol. 13. pp. 231-243) on fracture growth around openings in blocks of rock subjected to uniaxial and biaxial compression, using the Elfen discrete element code. The results of the physical experiments indicated a number of trends that were successfully replicated in the numerical simulations, including crushing ahead of the face, the formation of a sub-vertical tensile fracture at centre-span, the formation of groups of fractures originating from the crushed face zone, the formation of large corner-to-corner fractures which precede sample failure, and linking of slot corner and sample corner fractures leading to sample failure. In addition, other features were apparent that were not reported by Gay. It is believed that these took the form of conjugate shear fractures (as reported by Gay in a previous paper) and other features that may have been altered or inhibited by the presence of pre-existing structure in the physical samples. It was found that the samples, though nominally made up of the same rock type, must have had significantly differing properties. The presence of pre-existing structures may have contributed to this discrepancy. Strain measurements from the physical experiments were reasonably well matched, except where the gauge lay directly in the path of advancing fractures.

Jan 1, 2012

By T. Bhambhani, D. R. Nagaraj

"Ultramafic Ni ores present significant challenges in processing in that both recoveries and grades are not satisfactory, due to the presence of Mg silicates in large amounts. Significant quantities of xanthates and CMCs are generally used for their recovery by flotation. Additionally, given that some of these ores are processed under acidic conditions, CS2 generation due to xanthate decomposition presents some safety hazards. Technology to replace xanthate has been developed for which the safety and health issues are absent. Collector S-10294 shows significant improvements in Ni and overall S recovery at a dosing rate of one half that of xanthate. New polymeric modifiers have also been developed that help reduce the Mg content of the concentrates at very low dosages. The reagents are custom designed for use in normal or hypersaline water, and acid or alkaline conditions.INTRODUCTION The use of xanthates in sulfide mineral flotation is reported to have started as early as 1925 (Nagaraj 2005). The reagent is now ubiquitous in the mining industry, accounting for 40-50% of total collector consumption. In recent years, the development of more selective reagents has rendered xanthates largely obsolete in Cu flotation. However, xanthates continue to be sold in large amounts in the Au, PGM and Ni flotation industry, where bulk sulfide flotation is required. The low cost and easy availability is the largest driver for the use of xanthates in the minerals industry. Of particular interest to this study is the use of xanthates in the flotation of Ni sulfide ores. About 60% of the world’s annual nickel output is obtained from sulfide Ni ores (Hoatson, 2006). A strategically important category of these ores is the ultramafic hosted sulfides, such as those of Western Australia and Canada. These ores are characterized by low Ni grades (<1%), with the Ni minerals being pentlandite, violarite, millerite and mackinawite, and gangue minerals comprising an array of altered Mg silicates, mostly serpentines. The challenges associated with treating these ores are well documented (Eltham et al. 1973; Claridge et al. 1975). One challenge is that Ni recoveries from these ores are lower. This has been attributed to the increased pulp viscosity, as discussed in detail by Vasudevan et al., 2010. Additionally, Mg silicates tend to report to the concentrate in large quantities, which is problematic for two reasons: a) concentrate dilution, and b) the high melting point of Mg silicates tends accelerate wear on the refractory lining of smelters. This has been attributed to network transport to the froth phase via bubble flux and entrainment (Patra et al, 2010)."

Jan 1, 2012

By J. M. Benson

Metal powder compaction offers unique advantages in the manufacture of net-shape components using techniques such as laser sintering, conventional press and sintering, metal injection moulding, direct rolling, direct forging, and hot isostatic pressing. If the output from the primary metal production process is in powder form, then considerable cost and energy savings can be realized by direct conversion to semi-finished or final shapes. This possibility exists for titanium and possibly also for Ta, Zr, Hf, and Nb metals. However, these attractive benefits are associated with some significant risks. The high surface-to-volume ratio of powder particles coupled with the reactive nature of these metals means that special care must be taken when handling them. Powder explosions are unfortunately still a regular occurrence internationally and these often result in serious injury and loss of life. Even seemingly &apos;safe&apos; compounds such as sugar, flour, and grain can be extremely hazardous when handled or milled and dust clouds are produced. In addition, exposure to airborne particles can have adverse effects on the human body, especially when particles are inhaled on a regular basis. Furthermore, the medical consequences of these are not fully understood, especially in the case of nanoparticles. The impact is often not observed immediately and debilitating illnesses may emerge only years or decades later. As far as is known, there are no South African guidelines for handling of metal powders. This paper attempts to provide an awareness of the risks associated with metal powders (including those produced indirectly by other metalworking/finishing operations) as well as some guidelines for their safe handling, based on international best practices.

Jan 1, 2012

By R. J. Jewell

The storage capacity of any given tailings storage facility (TSF) is a function of the volume available for the tailings, for which the geometry of the final upper surface of the tailings is most important. One of the advantages that can be obtained from thickening tailings prior to discharge is that the tailings can be stacked at a steeper beach angle than is obtainable with conventional low-density slurries. However, there is at present no universally accepted method available for the accurate prediction of tailings beach slopes. This paper examines the current situation with the objective of putting the quest for a method for the accurate prediction of beach slopes into perspective. The paper references published reviews of the best-known beach slope prediction methods. However, there do not appear to be any independently verified projects or published references to projects on which a Class A prediction has been validated for any of these approaches, and in those instances where projects have been implemented correlation of actual with predicted slopes has been poor - often due to differences between the properties of the tailings assumed in the design and those actually achieved in the field. The author also concludes that flume-scale testing cannot be taken as a reliable indicator of full-scale performance, and suggests that the outcome of any current predictive method should be used by experienced practitioners as only one of a range of indicators in order to suggest a range of slope angles likely to result for any given operation. Practice has shown that it is possible to manipulate beach slopes by changes to the disposal technique, such as limiting the rate of discharge per discharge point and by increasing or decreasing yield stress, but the impact of these changes cannot readily be predicted. There are also newly emerging technologies, such as the injection of a polymer into the tailings at discharge, that will enhance the dewatering of tailings and hence expedite the consolidation of the tailings, that could well facilitate the development of steeper beach slopes. The overall conclusion is that with the current state of knowledge, the accurate prediction of beach slopes is not possible. Furthermore, in view of the inherent variability of the tailings parameters from any operation, it may well be of more value to concentrate on developing an understanding of the means by which the tailings parameters may be manipulated by the operators to achieve a given beach slope than to concentrate wholly on developing a generic beach slope prediction model.

Jan 1, 2012

By L. Bos

The availability and reliability of large grinding mills and their Gearless Mill Drives (GMDs) are of paramount importance for the grinding process. Although GMDs have been in service for decades, and are known for their operational efficiency (reliability and robustness with reduced operating cost per ton), compared to conventional drives, in the last decade due to certain reasons some failures led to serious unscheduled shutdowns and significant insurance events. The majority of these notable "insured" failures have happened on GMDs installed on relatively large mills, as the financial impact of a failure is proportional to the through-put of the mill. Despite the occurrences of these events, as mining operations are driven by lower ore grades and the ability to continue reducing operating costs per ton, the trend for having larger mills is still very present and there is no reason why this trend should not continue. It is obvious that if not handled correctly, the possibility of large value GMD loss events, coupled with the continuing increase in mill size or required availability and reliability targets, could potentially lead to major conflicts as it becomes difficult for the insurance companies to judge the risk and hence may result in hesitation to insure these grinding circuits. This paper will not only describe the conflicting situation from both an insurer&apos;s perspective and from an equipment supplier&apos;s perspective, but also how these conflicting challenges can be successfully mastered. It has to be noted that not only the mining companies themselves, but also their insurance companies and the involved equipment suppliers have a common interest: to reach the highest availability and reliability in order to avoid or at least minimize unscheduled shut down times, and most importantly prevent unplanned events that result in extended production stoppages or reductions in through-put of GMD driven mills. From the very beginning onwards, the complete service concept together with emergency plans must be integrated on every level in the design of the grinding circuit. This approach must be implemented continuously and without compromises by all involved parties during all following stages, such as basic design, detail design, manufacturing, quality inspection and testing, packing, transportation, storage, installation, commissioning, operation and maintenance. The concept of formal risk analysis related to mill operations, maintenance and spare parts strategies must be an integral part of mining companies? decisions related to the selection for installation and continued use of large mills powered by GMDs. The service concept in place for operating mills shall also have a clear focus on very early detection of any abnormalities, so that the risk can be mitigated and unscheduled shutdown times avoided. However, if a major failure occurs, then procedures and tools shall already be available in order to ensure that production impact is minimized.

Jan 1, 2012

By Adrian Dance

Newmont Ghana Gold Limited?s Ahafo operation have been working with Metso Process Technology & Innovation (PTI) since early 2009 to increase mill throughput from a combination of controlled blasting practices and optimised primary crusher and grinding circuit conditions. For such Mineto- Mill projects, PTI?s methodology is termed Process Integration & Optimisation (PIO). Ahafo operate a SAG mill, ball mill and pebble crusher (SABC) circuit that processes a range of primary ore of varying hardness from different pits which is blended with soft oxide material. The PTI study focussed on ball mill limited material from the Apensu open pit. Following a benchmarking study of all blasting, crushing and grinding practices in January 2009, PTI recommended changes in both blasting and crushing conditions in order to generate a finer feed size to the SAG mill. Additional operating changes in the grinding circuit were recommended. A series of trials were conducted in November 2009 where three blasts were fired using a different blast design (hole diameter and explosive type) in the same area of the Apensu pit as the benchmarked material in January 2009. Top and bottom benches (or flitches) from each blast were sent exclusively to the grinding circuit and the material was tracked using PTI?s SmartTag? system. The results from the six trials showed a significant increase in primary ore throughput at a reduced blend of oxide material. Ahafo have since standardised on these modified blasting conditions for all Apensu ore zones and have been able to sustain higher throughput compared to historical performance on similar material. This paper summarises the phases of the PIO project, the changes made in operating practices and the outcomes of the blasting trials that validated the predicted increase in mill throughput.

Jan 1, 2012

By Xue Wang, Callie Babbitt, Chelsea Bailey, Matt Ganter, Gabrielle Gaustad, Brian Landi

"Current trends, motivated by fossil fuel dependence and unprecedented greenhouse gas (GHG) emissions, show lithium-ion batteries (LIBs) emerging as a competitive energy storage technology due to higher power and energy densities compared to Pb-acid and Ni-metal hydride chemistries. These trends may be of concern, however, as environmental impacts are not well understood for either the LIB itself, or for the nanoparticles consumed or released during the battery's production, use, or end-of-life. This study combines economic modeling, dynamic material flow analysis, and fundamental material characterization methods in order to quantify some of the economic and environmental trade-offs for LIBs at their end-of-life. As expected, results show that as chemistries transition from Li-Co based cathodes to Li based Fe, Mn, and S cathodes, LIB recovery value correlates to the value of the raw materials used. These initial results aim to inform collection policies being proposed currently as well as enable future deployment of novel recycling techniques.IntroductionGlobal fossil fuel dependence and unprecedented GHG emissions have led to increasing attention on energy alternatives, for both electricity production and personal transportation. However, development of renewable energy systems is contingent on concurrent technological development of energy storage systems, primarily batteries used for power grid load-leveling, renewable energy storage, and hybrid and battery electric vehicles. In this sector, lithium-ion batteries (LIBs) are emerging as a competitive technology due to higher power and energy densities compared to lead-acid and nickelmetal hydride chemistries[!]. LIBs represent close to 20% of the total rechargeable battery market and 75% of the portable rechargeable battery market, which is the fastest growing segment of the rechargeable battery market, with a 20% global growth in 2008 [2].This surge in production ofLIBs indicates a looming waste problem; total waste from Li-ion batteries has likely grown substantially from the 500 metric tons estimated in 2003 [3]. Figure IA shows the substantial increase in world-wide lithium production that has occurred in the last several decades with batteries making up the largest share of applications (Figure lB). California and New York state legislators have attempted to proactively address this looming waste by issuing diposal bans on rechargeable batteries in their states[4, 5]. However, quantification of the costs involved in collection, transportation, and processing of these materials has not been examined in depth."

Jan 1, 2012

By Wen Chen, Xinghua Liu, Zeyou Peng, Qiulin Wang

"Limonite is a collective for iron hydroxide argillaceous materials. It is very difficult to be treated due to the wide variation in specific gravity and magnetism and the high argillization rate in the course of grinding and beneficiation. The iron ore in Huangmei, Hubei, China is the typical representative of limonite. If the limonite is processed using conventional physical beneficiation methods (e.g. magnetic separation, gravity separation, flocculation-desliming-flotation, or a combined process of the three), it can only be obtained an iron concentrate grade of 51.98% and an iron metal recovery of 86.64%. However, the technique of flash magnetic roasting-magnetic separation can improve the concentrate grade to 61.03%, iron recovery to 91.17%. This paper describes the tests of recovering limonite by flash magnetic roasting in detail.IntroductionLimonite (mFe2O3, nH2O)[1] is a general designation for hydrous iron hydroxides and argillaceous matters. Limonite is hard to be separated because of its complicated geneses, comparatively weak magnetism, nonuniform grain size and being easily slimed during grinding. So most small and medium enterprises sell deslimed limonite product which was dealt with just by simple methods of washing, magnetic separation or gravity separation and so on. In recent years with the iron ore prices soaring, significant progress was made in mineral processing research of limonite. Laboratory research and industrial test results showed that flocculation-desliming-flotation process and roasting-magnetic separation process are the two best methods to recover limonite till now. To compare these two methods, roasting-magnetic separation process is superior to flocculation-desliming-flotation process in aspects of beneficiation indexes and industrial stability."

Jan 1, 2012