Search Documents

By J. M. Wempen

As development in underground coal mines progresses away from the critical components of the ventilation system, including the main fans and ventilation shafts, resistance within the system is markedly increased. This results in higher pressure and flow requirements from the main fan(s) to maintain adequate face ventilation. Upgrades to the primary ventilation system are often required. The use of booster fans underground is a potentially practical alternative to the addition of shafts and surface fans. This study presents simulations of the use of booster fans in two underground ventilation scenarios, one longwall and one room-and-pillar. The booster fan effects on the power requirements of the ventilation systems are evaluated.

Jan 1, 2011

By B. B. Adhikari, S. Alam, Ohto Kawakita, Abe Pangeni

Effective recovery of gold was investigated by using adsorption gels prepared from pure cellulose, cotton and paper by treating with concentrated sulfuric acid. Only gold was adsorbed with extraordinary high loading capacity from varying concentrations of hydrochloric acid separated from other precious metals and base metals. The formation of fine powders of metallic gold was visually observed, which is attributable to the selective reduction of gold (III) ion to metallic gold clue to its high oxidation-reduction potential. Recovery of gold from the leach liquor of hydrochloric acid of circuit boards from spent mobile phones was attempted using pure cellulose gel.

Jan 1, 2011

By Gui DeReamer

Located on the Wabash River in the central portion of the state, the city of Lafayette, IN is relatively small compared to most cit-ies that incorporate tunnels into their combined sewer overflow (CSO) systems. The original CSO plan for the city was to replace two aging lift stations that were built in the 1950s. The original con-cept was to build a new sewer using conventional cut-and-cover construction to eliminate one of the lift stations ? the Parking Lot Lift Station ? and build a new regionalized one at the location of the Pearl River Lift Station. The initial sewer design was sized just to handle the flow that would eliminate the Parking Lot Lift Station. The planning for this project was being developed as part of the city?s CSO long-term control plan (LTCP) that focused on reducing the overflows from the city?s 14 overflow points. However, during the development of the CSO LTCP, a major industrial user indicated it would be increasing its flows to the system, which required additional conveyance capacity to meet the city?s CSO LTCP. After reviewing the design concepts with city representatives during the planning phase of the project, the mayor indicated that he wanted to minimize impacts to downtown businesses; therefore, trenchless alternatives were considered. The last piece of the puzzle that drove the project away from a small diameter pipeline was discovered during a flow monitoring program to collect flow data for the CSO LTCP project. This study revealed a major restriction in the 100-year-old Pearl River Trunk Sewer, located beneath four active railroad tracks. To eliminate this flow restriction, provide more overflow storage and reduce the impact to local businesses, a new 2.7- to 3.6-m- (9- to 12-ft-) diameter tunnel sewer became the most viable solution.

Jan 1, 2011

By T. D. Chatwin

Acid rock drainage (ARD) is one of the most serious and potentially enduring environmental problems of the mining industry. High liability costs carried by many mining companies to cover potential obligations of ARD are a clear indication of the gravity of the problem. Unchecked, ARD can result in water quality impacts that could well be the industry's most significant financial and credibility risk. Effectively preventing acid drainage is a formidable challenge that requires the total commitment of the mining industry throughout the entire life-cycle of a mine. To achieve this commitment a strong business case for ARD prevention must be developed. This paper will address the elements of acid prevention and discuss their importance not only to the company but the entire industry as well. The International Network for Acid Prevention (INAP) is an industry-led group created to help meet this challenge. In 2009, INAP published the GARD Guide (www.gardguide.com), a web-base best practices guide for the prevention of ARD [1]. In this paper, the GARD Guide will be used to identify preventative actions for all mining industry stakeholders. It will, in turn, be used to estimate ARD management and mitigation value accrued to the company from ARD prevention, which will be used in developing a business case for acid prevention.

Jan 1, 2011

Evver since it first displayed an autonomous mining truck at the 1996 MinExpo show in Las Vegas, NV, Caterpillar has been building the blocks to a fully autonomous mine. In May, the company unveiled another block in that progression, the new Cat MineStar System that it says is ?the industry?s broadest, most comprehensively integrated miner operations and mobile equipment management system.? The full system is comprised of five capability sets ? Fleet, Terrain, Detect, Health and Command ? to help operators define the size and scope of their management system based on the needs of their mining operations. Michael Murphy, technology and autonomy manager for Cat Global Mining, explained that the customers were not ready for an autonomous mining truck in 1996, but that many customers wanted the building blocks to eventually get to autonomous mining. After 15 years of work, Murphy said the building blocks have come together in the form of the Cat MineStar System.

Jan 1, 2011

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"Reduction of combustion-emitted greenhouse gases, which are associated with global warming, may be achieved by use of CO2-neutral alternative fuels, such as bio-ethanol. Distillers Dried Grains with Solubles (DDGS) are the main co-products of the com-grain-based ethanol industries. In 2009, the North American production of ethanol from com was about 38 billion liters, which generated approximately 31.5 million tons of DDGS. Samples of DDGS were pyrolysed at temperatures of 600-1000 °C in a two-stage laminar-flow horizontal furnace, and a catalyst system was used to synthesize nanomaterials. This work presents a microstructural characterization of these nanomaterials by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Results showed that the nanomaterials produced from pyrolysis of DDGS were in the form of long, entangled, rope-like structures with rugged walls, lengths in the tens of microns, and axially non-uniform diameters in the range of 100-300 nm.IntroductionThe interest in ethanol has increased considerably worldwide due to the necessity of finding renewable and cleaner energy resources [1, 2]. According to the Renewable Fuels Association (RF A), the world ethanol production in 2008 was approximately 65.7 billion liters (17.3 billion gallons), which figure represented a 24% increase in the production over that in the previous year [3]. The major producers of ethanol are the USA and Brazil, which together account for 90% of world production. The main feedstock for ethanol in USA is com grain, whereas sugarcane predominates in Brazil [2-4]."

Jan 1, 2011

By A. R. Farkoosh

Al-Si based alloys have been recently used by automotive industry for highly stressed engine applications. Due to severe working conditions of the engine parts, existing alloys hardly endure high pressures at high temperatures. This necessitates alloy modifications to enhance the elevated temperature performance. In this study, the effects of trace nickel additions on the microstructural and mechanical properties of A356+0.5Cu alloy have been investigated at different aging conditions. Electron probe microanalysis (EPMA), scanning electron microscopy (SEM) and X-ray diffraction (XRD) are used to study the microstructural changes. Aging curves have been obtained by hardness measurement. It was seen that the presence of additional nickel introduced many complex intermetallic phases within the microstructure which led to improved high temperature mechanical and aging response.

Jan 1, 2011

By Wm. Reisz, Raphael Trousselle

We are now well into our second decade of commercially available electronic initiation systems. Over this time, the technological advances have made electronic systems a very practical option for a wide variety of blasting applications.

Jan 1, 2011

By Russell C. Frith

Risk-based roadway roof support design is now a critical part of the Australian Coal Industry. Safe and efficient mining demands that roof support be tailored to the prevailing geotechnical conditions and coal mining legislation in New South Wales, Queensland, and Tasmania is clear in requiring that formalized roof support design be undertaken. The assumption of dead-load suspension of an otherwise unstable roof has been used in roadway roof support design for many years. However longevity does not necessarily translate into either a best or even reasonable practice in the current industry, particularly when pro-active strata management systems are now routinely used and reinforcing support design methods are available. The paper discusses why the assumption of dead-load suspension is fundamentally incorrect in almost all instances when pro-active or reinforcing roof support is applied and how it can easily result in misleading and potentially under-designed roof support systems under various circumstances. The commonly used design methodology of balancing the installed axial capacity of long tendons with the assumed ?weight? of a future roof fall is summarized, and several fundamental flaws are identified. The critical area of selecting the design Factor of Safety is also discussed in detail. Accepting that under certain circumstances the roof of a roadway will require it to be ?suspended?, suggestions are given for how a robust support system can be developed, designed and applied.

Jan 1, 2011

By Sanjay Kumar Singh

This paper presents ground control technology associated with a continuous mining operation for mass exploitation of underground coal deposits in the Indian coal mining Industry It shows that competency of roof strata and performances of continuous miners are safer, than other coal mining method as well as productive and economical. Continuous miners keep playing a major role in the underground coal mining industry for their safety and as well as their productivity. Regarding past experiences in Indian coalfields, Chirimiri and Jhanjara mines have achieved exceptional performances, with a potential for over 500,000 tonnes per year. Tandsi mine has difficult roof conditions and does not typically achieve high production and productivity. Even so, the difficult roof conditions have been controlled with modern ?world best practice? roof bolting systems and an output of up to 1,200 tonnes per day has been achieved. It can further be emphasized that if this technology is implemented properly it will bring an unfathomable change to the Indian mining scenario. There are many mines in India that may have potential and economic viability with ground control technology concepts for installing continuous miner systems and beginning mass exploitation of underground coal deposits.

Jan 1, 2011

By Steven R. Lowe

Construction of a pump station, consisting of an inlet chamber, wet well and pump chamber, required excavation to a depth of 9.7 m (32 ft) below ground surface and more than 7.6 m (25 ft) below the ground water table in a rural, but rapidly developing part of southern New Jersey. Private houses are located [ ] within a few hundred feet of the pump station that use shallow wells for water supply. The pump station design anticipated support of the entire pump station on shallow foundations bearing directly on the underlying natural soils. However, during construction, uncontrolled ground water flow caused ground loss and damage to the bearing qualities of foundation soils. As a result, remedial repairs were required including support of the pump station on drilled pile foundations and releveling of the pump chamber that had settled. This case study is an example of where a poor understanding of the significance of upward flowing ground water had a major impact on the cost of construction. Anticipated subsurface conditions The pump station layout is shown in Fig. 1 with the locations of two borings made prior to construction superimposed. One of the borings was located within the footprint of the deep wet well excavation. Generally, this is not advisable where a deep excavation is required below the ground water table. This is because there is a history of projects where ground water seepage, or pressure, has broken out into an excavation through an ungrouted borehole and compromised the integrity of foundation soils. Logs of the borings did not indicate that the borings [ ] were grouted upon completion.

Jan 1, 2011

By D. Kwietnewski

With all of the unknowns associated with tunnel construction, how does a contractor choose a roadheader? This paper presents a review of several models of roadheaders being used in today?s tunnel projects. The features of different models of roadheaders are presented and compared. Roadheader size and cutter power generally determine which roadheader is best for a particular job. We will also present a model for matching features of the roadheader to the anticipated ground conditions such that the most efficient machine is selected for the project.

Jan 1, 2011

By M. Nzotta, L. Teng, S. Seetharaman, A. Chychko

The objective of the present work is to optimize the EAF practice towards Mo alloying with maximum retention of the alloying element in molten steel. During Mo additions, there were significant losses to the dust (ca 7 %) and to the slag phase (ca 2 %), which had serious economic and environmental impacts. The present work was aimed at designing a suitable Mo precursor, an alternative to ferromolybdenum, as the Mo source and a process sequence for optimal retention of Mo in the steel. The design of the Mo source should be in such a way that low cost raw materials such as MoO3 concentrate have to be used, stable during the addition so that the vapour phase losses as MoO3 are kept minimum and the dissolution of the precursor in molten steel is easy without loss to the slag phase. After thermodynamic considerations, three precursor materials were chosen, viz. CaMoO4, MgMoO4 and Fe2MoO4. Synthetic mixtures of the component oxides in each case as well as pure MoO3 were investigated by TGA and high temperature XRD in order to find out the temperature range in which the compounds were formed. Experiments were also conducted separately where the evolved gases were analyzed. All the three precursors were formed easily and the loss of MoO3 to the vapour phase was found to be extremely low. Addition of the oxide mixtures to steel melts were conducted in three different scales, viz. 16 g, 500 g and 3 tons (induction furnacle). Initial experiments showed that MgMoO4 was not suitable since the Mo yield in the steel melt was not very high. Fe2MoO4 was found to perform best, the Mo yield reaching 98 %. Further trials were conducted in the 65 ton Electric Arc Furnace (EAF) at Uddeholms AB in Hagfors. Mixtures of mill scale, MoO3 and carbon in suitable proportions were added in a pre-determined addition sequence. It was found that, in the actual practice, the Mo yield reached 99 %, equaling in performance the addition of ferromolybdenum. The process offers an effective use of cheaper raw materials and very high Mo yield avoiding a pre-treatment step like the production of ferromolybdenum. This is both cost effective and environmentally advantageous. The process has been patented and is being currently implemented at Uddeholms AB, Hagfors, Sweden.

Jan 1, 2011

By L. E. C. Pignatari

Mine reconciliation is seen, for many, as a test of the quality of model estimates, while in fact it should be seen as a powerful tool for detecting and correcting problems in each step of mining operations, from resource estimation to metal production. Adequate reconciliation practices allow a more efficient control of the mining processes; however, its results can be illusory unless all parties involved have been in compliance with the principles of sampling correctness. This paper presents a new, segmented reconciliation matrix, which is based on the Theory of Sampling (TOS), developed to monitor gold operations and reserve estimation.

Jan 1, 2011

By Trevor R. Ellis

Minerals appraisers/valuers often find great difficulty in attempting to employ the sales comparison approach to the market value appraisal of development and operating stage mineral properties. An important factor generally overlooked is a comparison of net operating income (NOI) margins on a per-unit-of-production basis between mineral properties, whether these be demonstrated or forecast margins. NOI margins can vary greatly between mines or quarries that are producing similar products. Ultimately, the expected NOI margin determines what a buyer is willing to pay for an income-producing property. Here, common criticisms of the sales comparison approach by mineral appraisers are introduced. These are counterbalanced by raising some issues in the way the inputs for the income approach are usually derived by minerals appraisers and by review of some conspicuous examples of the much-too-common misuse or abuse of the income approach in market value mineral appraisals. Example transaction analyses and sales comparison analyses are used to demonstrate the author?s methodology for adjusting units of resource in his transaction adjustment tables. The examples are used as the basis for a discussion of ways to employ adjustments for operating economics and many other factors, while warning against the potential for double counting. The conclusions include a recommendation that minerals appraisers attempt to apply at least two of the three valuation approaches when appraising the market or fair value of development and operating stage mineral properties, the two being the sales comparison and income approaches.

Jan 1, 2011

By Karl Christopherson, Vanessa de Viterbo

Trim blasting is an integral part of the mining processes at the Morenci Mine, a Freeport-McMoRan Copper & Gold Inc. property. Trim blasting near high-walls or Finals blasting requires a tighter distribution of energy but a reduction in total energy factor near the wall. Recent Finals blasting in Morenci Mine was allowing the shovel to dig to the final design limit, but causing high-wall instability due to excessive energy or production of energy (blast design and timing). Slope instability events reduced production in two of the three operating pits in Morenci over 2009. In order to avoid high-wall instability from Finals blasting, a new method was required. The new method utilizes air-decks, unconventional row timing, and blast design based on the geology predicted. Many different geologic structures and rock types exist in Morenci, and different strategies were needed for the many predicted geologies. Drill penetration rate and core mapping were the primary tools for determining the blast design. Patterns were designed within a consistent geology; with weaker rock types receiving a lighter load than the stronger rock types. Penetration rate returned by the drill would be the determining factor on the actual rock hardness. Maintaining the pattern geometry on Finals designs should not be an issue as long as the lb/hole is adjusted to reduce powder factor close to the high-wall. One requirement of Finals blasting should be that the powder factor matches the geology as closely as possible. A softer, fractured zone should use approximately one-half to two-thirds the explosive charge of a competent, sound geological zone. This has been incorporated into the final Trim blast design. It is impossible to protect every high-wall from close-in blasting, especially those with crossing prominent joint sets inclined toward wedge failure, but this new design has provided protection on walls where the mine was encountering problems.

Jan 1, 2011

By S. Amid, D. Fisk

"Wireless technologies are permeating the mining and metals industry and enabling a myriad of benefits. With standards such as IEEE 802.11 for wireless devices and ISA100.11a for wireless field instruments protecting their investments, customers look to benefit from the cost and flexibility offered by wireless devices. Using wireless field instruments, plants are eliminating the costs associated with wired system by 50 to 70% and using these savings to install more field instruments, which, when used smartly, enables them to optimize their processes efficiency and equipment reliability. Wireless also empowers a mobile workforce by allowing them to have access to key process and maintenance data directly from the field. This paper describes how wireless can help operations and maintenance personnel to be more effective. Three case studies, illustrating how the mining and metals industry is taking advantage of the technology today, are presented:1.,Optimisation of the water recovery process using wireless2.,Field operations improvement with wireless handhelds3.,Improving fleet maintenance through wireless mobile equipment management"

Jan 1, 2011

By J. van Huyssteen, M. Cantor

Newmont Ghana Gold Limited's Ahafo Operation has matured from its project ramp up stage into steady state operations after three years of operation. Management focus has shifted from addressing construction and commissioning problems to optimization and improvement. This focus change has coincided with the introduction by Newmont of a Continuous Improvement (CI) program across the company which provided a project management methodology that can be used in the execution of smaller scale projects. This paper focuses on the application of CI principles at the Ahafo Plant through the discussion of several case studies that demonstrate how these principles are applied.

Jan 1, 2011

The objective of this handbook is to provide the inspector with guidance for recognizing hazards from inhalation contaminants in above ground work areas of underground and surface metal and nonmetal mining and processing facilities and evaluating these hazards by collecting samples or making field determinations and interpreting the analytical results. Portions of the handbook that should prove most useful to the inspectors include a survey check list, rules for determining if sampling is required, list of most frequently encountered contaminants, list of candidate contaminants and their sampling conditions, interpretation of results, and a procedure for a health and safety inspection.

Jan 1, 2011

By D. Lauriski

The recent spate of catastrophic events at U.S. mines raises the question as to whether or not the mine safety and health system in the U.S. is broken. The prescriptive regulatory regime in the U.S. is not a cure-all for a broken system. Without totally dismissing the contribution of a prescriptive regulatory approach, this paper argues that safety in the U.S. mining industry would be enhanced if the nation adopted a scheme that provides a balance between specification standards and two alternatives: performance and systems-based standards. This would allow effective and flexible means to continuous health and safety performance improvement. Mine operators, regulators and politicians could then go beyond thinking that compliance alone equals strong safety by creating a proactive system that emphasizes continuous improvement. By adopting performance and systems-based standards, exemplary safety and health performers can be recognized, allowing regulators to focus their efforts on those without sound occupational safety systems and who have substandard safety performance. Mining Engineering, 2011, Vol. 63, No. 7, pp. 77-82. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011