Search Documents

By B. Grosso

The National Italian Regulation concerning environment protection imposes that industrial areas are provided with systems aimed at preventing the circulation of contaminated groundwater. These systems can be static or dynamic and operate basically by intercepting the contaminated flow. Their effectiveness, realization time and costs depend on the intervention type and on the features of the specific site. The selection of the best solution is complex and the results obtained by this selection may be affected by residual risks related to the uncertainty of the hydrogeological and geotechnical characterization of the site. With regard to the industrial area of Portovesme, located in the south of Sardinia, the paper presents the analysis of alternative interventions aimed at the protection of the groundwater. The attention is focused on the evaluation of their effectiveness, impact on environment and, finally, time and costs of construction.

Jan 1, 2008

By Scott G. Britton

Mine exploitation is a broad subject whose focus is the technical skills or efforts needed for the extraction of mineral from a known ore body. Mine exploitation can be considered the very core of the mining engineering discipline. It begins at the conclusion of the exploration and development stages of mining and ends when the ore body is exhausted and the mine (or mines)closes and is reclaimed. Section 8 on mine exploitation is comprised of seven chapters: (1) classification of mining methods, (2) mine surveying and mapping, 3) systems engineering, (4) computer methods, (5) labor relations and training, (6) management and administration, and (7) mine closure, sealing, and abandonment. Each chapter focuses its efforts towards providing detailed and useful information for the engineer on basic mine exploitation principles. The information can be applied to a broad range of mining problems without regard to mineral type or mining method.

Jan 1, 2008

By Wenbin Liu

A novel route for rapid synthesis of ultrafine WC-Co cemented carbides with homogeneous binder phase distribution is reported. The composite powder is produced by in situ reduction-carbonization reactions by using WO2.9, Co3O4 and carbon black as raw powders. The reaction equilibrium and phase stability are studied by thermodynamic calculations. The WC-Co composite powder is condensed by spark plasma sintering (SPS) to obtain the cemented carbides bulk. The sintering temperature is lower than that in the conventional sintering methods by 1500C, while the sintering time is remarkably reduced by 3-5 times. The high performances of the hardness and the fracture toughness are obtained. The experimental results confirm that the present processing scheme of in situ reduction-carbonization reactions and subsequent SPS sintering is an efficient way to prepare WC-Co cemented carbides, and is apparently superior to the conventional long-period techniques of preparing composite powder and cemented carbides bulk.

Jan 1, 2008

By J. Kang

To obtain microbial cultures with the ability to efficiently leach copper ion from chalcopyrite, microbial samples from acid mine drainage sites were mixed and then subjected to mutation using sodium nitrite (NaNO2), diethyl sulfate (DES), ultraviolet light (UV) and their combinations. Mixed cultures with a much stronger ability to leach copper ion (identified as mixed cultures A, B, C, D and E) were obtained by screening on leaching media. Leaching tests showed that mixed culture E had the best leaching performance and increased the Cu2+ content by 120.5% in 20 days, compared to a control without mutation treatment. Mixed culture E grows well on Leathen leaching medium supplemented with Cu2+ (at a final concentration of 32 g/L), reaching 3.2 × 107 cells/L after 15 days, while the unmutated control culture cannot survive beyond 15 days, indicating that mixed culture E is more tolerant of high concentrations of Cu2+. In addition, continuous leaching by mixed culture E is very effective at a pulp density of 1%. These results suggest that it has the potential for industrial applications.

Jan 1, 2008

By P McCarthy

Despite significant advances in the platform technologies that could form part of a system of mine automation, the goal of full automation in most underground mining applications remains distant. This is because the industry developed these platform technologies to achieve local improvements in safety, machine and labour productivity, and asset utilisation, rather than to work towards a goal of a complete system of automation for general application in underground mines. This paper reviews the history and current state of automation in the underground mining industry and uses lessons learnt from the automobile and general manufacturing industries to gain insight into the opportunities and pitfalls in the complex and uncertain path to automation of underground mines. It also evaluates the relevance of the current drivers of interest in the industry. From this, we hope to engender an attainable vision of automation in underground mining and determine the best development path, process and timeline to achieve this vision.

Jan 1, 2008

Mining of narrow vein mineralisation, invariably depending on the mining method selected, involves the extraction of both ore and waste rock. The level to which mining of waste rock can be minimised depends on numerous factors, but particularly the thickness and dip of the deposit. Resue mining is a method of mining that allows split face firing within stopes to allow waste and ore to be mined separately, allowing dilution to be minimised. This paper examines the technique of resue firing and its applicability to the mining of narrow vein deposits. Particular emphasis is placed on the conditions in which resue mining presents a suitable option for mining of narrow veins.

Jan 1, 2008

By William Connell

NFPA 502, Standard for Road Tunnels, Bridges and Other Limited Access Highways establishes minimum fire protection and fire life safety requirements for road tunnels, bridges and other roadways where access by emergency responders is physically limited. The 2008 edition of NFPA 502 represents the Technical Committee?s consensus of current best practice for fire protection and life safety requirements for road tunnels, bridges and similarly limited access highways. Research of national and international test programs, design guidelines and regulating standards was per-formed and considered in an effort to establish a singular, comprehensive document representing a recognized base threshold of fire safety in these type facilities. This paper provides an overview of the more significant revisions including the application of fixed fire suppression systems, guidance on tenable environment, protection of structure and dangerous goods transport.

Jan 1, 2008

By Mike Tracy

This section of the Handbook deals with general principles to be evaluated in the development of a mining operation. It addresses the major issues that must be examined to fully evaluate a mining venture. Of course, one of the main topics to be evaluated is mine planning, which is covered in more detail in other sections (13, 17) of the Handbook and should be referenced in mine development projects. The topics to be discussed in this introduction include equipment and supplies, infrastructure, utilities, and project management. In any of the aspects mentioned, the current existing conditions at or near the mine site must be evaluated. This will include assessment of current use of utilities, infrastructure, housing, equipment suppliers, etc., as well as anticipated growth, both in the supply aspect of these systems as well as projected usage on these systems. After full assessment of both these aspects, an evaluation must be made as to the requirements the project will place on these items. Assessment must be made as to any up-grades required to bring the project on line, what impact the project will have on existing or expanded systems, and anticipated future growth impacts on support systems not only of the project but of other surrounding industry and urban devel-opment

Jan 1, 2008

By Thomas C. Ruhe

The Bureau of Mines conducted research to determine the safe operating conditions for using recycled (used) lubricating oil from mining equipment as a partial replacement for diesel fuel to make ANFO-type blasting agents. The use of recycled oil (RO) saves energy, reduces oil imports, and reduces mining costs. Low ambient temperatures may cause these recycled oils to become too viscous for proper absorption by ammonium nitrate (AN) prills and result in poor blast performance, safety hazards, and environmental problems. To help quantify and resolve these issues, viscosity, mixing, and performance tests were conducted at various temperatures. Diesel fuels No. 1 and No. 2 were studied separately and in blends with 25,50, and 75% RO. Good quality ANFO mixes (94-6) were produced with dry absorbent prills and blended fuel (No. 1 diesel plus RO) at temperatures as low as -40°F (-40°C) with 75% No. 1/25% RO, and at -20°F (-29°C) with 50/50. Diesel fuel No. 2 also made good mixes as low as -30" F (-34°C) with 75% No. 2/25% RO, and at 0°F (-18°C) with 50/50.

Jan 1, 2008

Copper-Cobalt hydrometallurgy has seen a resurgence in recent years with the development of projects in Zambia and the DRC. Many of the flow sheets are unique in their use of hydrometallurgical techniques to improve performance compared to the older types in current use. The emphasis has moved from direct copper electrowinning/stripping, with multiple stages of precipitation for removal of impurities and concentration of cobalt, to innovative use of solvent extraction and ion exchange with higher cobalt recoveries to final product. The poor quality direct electro-won copper has been supplanted with solvent extraction-electrowinning; with consequent production of LME 'A' quality metal. Many of the precipitation steps in cobalt recovery and concentration, have been replaced with solvent extraction; while the remaining precipitation stages have been enhanced with use of oxidants to improve impurity removal. Operating experience from two of these circuits has shown the benefits of the new technologies and the improved overall recovery of both copper and cobalt into higher quality products.

Jan 1, 2008

By D Laurence

Significant developments in future mining systems, technology and best practices are emerging that are driven by issues relating to human resources, competitiveness, environmental and social responsibility, within the dynamics of globalisation. It is proposed that the definition of the role and attributes of the mining engineer in the mine life cycle needs to be viewed more holistically in the face of increasingly more diverse and complex responsibilities. These developments are motivating the need to consider a fresh approach to mining education and training at all levels for industry. A growing diversity and complexity of professional responsibilities is extending the mining engineerÆs broadly based skill set and reinforcing the need to play a central role within increasingly interdisciplinary teams. On the other hand, the imminent new technologies that will transform the mining process are prompting the assumption that more focused and specialised skill sets will be needed. A way forward is suggested that would first define a blueprint for the future mine, as an attempt to characterise the systems architecture, processes and organisation of the next generation mine. This can be the basis for assessing the nature of the workforce and distribution of responsibilities, from which can be inferred the skills and training requirements. In the context of the mining engineer, the paper explores how understanding such future requirements will enable more proactive development of a strategy for educational development. The paper then concludes by considering issues and lessons learned from some recent mining educational development initiatives underway in Australia and Canada that are shaping significant change.

Jan 1, 2008

By T Raynlyn, J J. Campbell, R J. Holmes, J R. Manuel, S P. Suthers, A Poliakov

Prediction of the downstream processing performance of iron ore needs detailed information on mineral composition, textural peculiarities, particle density, porosity, mineral liberation and association and mineral grain size. Optical image analysis and automated iron ore texture classification systems are a way of obtaining such information. Furthermore, this information can be used for predicting the output of specific processes and their combinations. Several examples of the application of such an approach to process performance studies for iron ore are discussed. These include the application of classification by ore texture to modelling and optimisation of hydrocyclone performance, the effect of including textural information in modelling of sinter properties, and combining textural information with an experimental study of stirring and ultrasonic treatment of haematitic-goethitic iron ore fines to understand the deportment of fines and the breakdown/deagglomeration of particles. In all cases, the availability of textural information is important and helps provide a better prediction of process performance and/or understanding of the unit process.

Jan 1, 2008

By Brian Wilson, John Scholte, Megan Atkinson

"In November 2004, the residents of the City of Nanaimo, B.C., Canada voted to approve a new conference centre as the centrepiece of a proposed revitalization project for the city’s historic downtown core. The proposal goal was to replace a cluster of derelict buildings with a dynamic and modern complex that would connect existing city facilities to a new conference facility, the Vancouver Island Conference Centre (VICC). The conference centre is expected to create 150 full-time jobs, attract visitors/ delegates from across North America and generate new economic opportunities for local businesses.However, the proposed site posed a number of geotechnical and geoenvironmental challenges. As is often the case with coastal cities, historic growth of the Nanaimo downtown and harbour area was achieved through reclamation of former waterfront areas and inlets. These areas were often infilled with random fills and even wastes, leaving a legacy of variable density heterogeneous fills contaminated with a variety of pollutants. Preliminary assessment of the site indicated a high likelihood of a requirement for deep foundations, a high risk of liquefaction in the event of an earthquake and the presence of both soil and groundwater contamination. Construction would be further complicated by the requirement for two levels of basement parking and the proximity of adjacent buildings and major roadways to the work area.With a limited budget (fixed by the referendum) and timeframe, the city needed a cost-effective solution to proceed with construction. A number of options were considered, but an innovative design using leading-edge Cutter Soil Mixer (CSM) technology best met the geotechnical and budgetary requirements of the site. The CSM approach also addressed the environmental concerns of contaminated soils and groundwater. Golder Associates Innovative Applications (GAIA) Inc., in association with the designers of their parent company Golder Associates Ltd. (Golder), proposed the CSM technology — at the time the first North American application."

Jan 1, 2008

By G. G. le Roux

The purpose of the investigation was to assess various options for increasing the efficiency of the conveyor belt transporting system used at 4 Belt Shaft at Lonmin?s Marikana operations. The reason for the investigation was to prevent the occurrence of a ?bottleneck? at the main ore passes delivering ore to the conveyor belt system, thus creating more fluent operational conditions. The options assessed for increasing the efficiency of the conveyor belt transporting system were: ?Variation of the conveyor speed ?Concurrent tipping from two ore passes on the belt ?Increase the available drive unit power ?Increasing the feed rate from vibratory feeders ?Change in belt width/belt specifications The report shows that the most preferable option to the current situation at 4 Belt, Lonmin, would be the option of concurrent tipping from two ore passes to the belt.

Jan 1, 2008

By Christopher J. Vise

Although production operations at mines, representing the extraction and removal of the mined material, often appear to receive the greatest amount of attention, the emphasis given to auxiliary operations is continually increasing. This is due to the changing economic, social, and environmental climate in which modern mines must operate. Auxiliary operations can best be described as those activities that are not directly related to the extraction and removal of the mined material, but must receive proper attention if recovery is to take place in a safe, efficient, and socially responsible manner. In fact, certain mining auxiliary operations, such as strata control and ventilation, are considered to be of such importance that they warrant separate sections in this Handbook. Judging from a mine-personnel standpoint, it is not uncommon for a mine to hire the same number or more individuals responsible for auxiliary operations as the number assigned to production.

Jan 1, 2008

By David Estrella, Hector M. Lizama, Jhonny Carrión

"Microcel™ sparging systems were installed on one column of the molybdenum cleaner circuit and one column of the copper first cleaner circuit at Antamina. The Microcel™ system is known to generate finer bubbles than jetting-type spargers, and smaller bubbles have been associated with higher recoveries in flotation. Alternating tests were carried out on the molybdenum column, using either jetting-type spargers or the Microcel™ system. Experimental conditions of gas flow rate, wash water rate, and froth depth were tested. Use of Microcel™ decreased the bubble sizes from 2.6-2.9 mm to 1.5-2.0 mm. In addition, Microcel™ improved both unit molybdenum recovery and unit molybdenum concentrate grade. In the copper first cleaner circuit, side by side tests were carried out that compared the Microcel™ column with a parallel columns fitted with jetting-type spargers. Best results were obtained at manifold pressures of 260-290 kPa, where bubble sizes of 1.6-2.6 mm were observed. In either copper or molybdenum flotation, the Microcel™ system required only 50-60% of the gas flow used by jetting-type spargers.INTRODUCTIONAntamina is a copper-zinc mine located in the Peruvian Andes. Compañía Minera Antamina is owned by BHP Billiton (33.75%), Xstrata (33.75%), Teck Cominco (22.5%), and Mitsubishi (10%). The mine was commissioned in 2001 with a capital investment of US$2.3 billion, and has a nominal 100,000 t/d mill capacity. Mining, milling, flotation, and tailings impoundment take place at the mine site, which sits at an altitude of 4,300 m above sea level. The deposit is a polymetallic skarn ore body with intrusive phases of quartz-monzonite porphyry into Cretaceous aged limestone [Evans et al, 2005]. Ore body thickness is 100 to 150 m and has the shape of a flat-lying crescent. Copper is present mainly as chalcopyrite with a minor bornite component. Zinc is present as sphalerite. Molybdenum is present as molybdenite. Some lead, bismuth, and silver are associated with the sulphides. The deposit is currently classified into six main ore types [Dechert, 2006], grouped into two categories: copper and copper-zinc. The mill produces four concentrate types: copper, molybdenum, zinc, and lead-bismuth. Copper, zinc, and lead-bismuth concentrates are transported by pipeline down to the port of Huarmey. Molybdenum concentrates are bagged and trucked to port."

Jan 1, 2008

There are many different challenges when sampling mineral commodities. Sampling is part of many decision-making processes, from control of the number of drops of a reagent to all aspects involved in determining how much to pay for a mineral consignment. However, if all decisions must be supported by correct assumptions, or at least agreed terms, how can this be guaranteed? The main approach is to emphasise the importance of continuous surveying of sampling practices. If they are based on non-recommended protocols, this raises concerns. In addition, safety failures and lack of appropriate behaviour from the technical perspective can lead to disasters, both from the human and business perspectives. Impacts on safety and health are clearly unacceptable. It should be noted that imperfect safety and health practices in sampling operations have a strange correlation with incorrect sampling techniques. The commercial interface can also be affected. Companies have studied extensively the various aspects of measuring quality parameters for mineral commodities to understand the risks for investors and owners, and they take decisions that fundamentally respect the interests of parties in contracts and not result in losses. Every result should be obtained in defensible ways, and neither losses nor profits taken in indefensible ways. Most of such situations are related to bias; a significant systematic difference between a measured value and a reference value for a contractual quality parameter. Bias is always undesirable, because it always implies an incorrect advantage for one party and without doubt an undesired disadvantage for the other party. These situations are solved financially through a third-party arbitrator becoming involved in delicate situations, such as a commercial claim, but the outcome is always tangibly or intangibly bad for one of the parties. Another possibility is a permanent or temporary loss of precision. Poor precision, due its nature, generates reasonably balanced losses and profits, but it may hide out-of-control situations, generate instability and induce financial losses due to actions taken towards clearing commercial disputes involving interlaboratory programs, sample exchanges and duplicated sampling and sample preparation procedures, in the end wasting time and resources and creating a permanent source of commercial tension. While bias situations demand immediate adjustments for correctness, poor precision has to be understood as something that cannot be just calibrated out and is a situation that demands investment of time and effort. Precision optimisation has to take into account best practice for obtaining the required precision as well as cost/benefit analysis studies. Purchasers, engineers, salesmen and all personnel need to recognise that sampling is a major area to understand when taking decisions. The aim is to spread concepts that can really help, such as simple in-house actions to improve productivity and completion of surveys on commercial sampling operations, in order to ensure correct results are obtained and assertively take corrective actions, thereby establishing a healthy relationship with investors, suppliers and purchasers and in the process optimising the business.

Jan 1, 2008

By D A. Collins

The floatability methodology developed by the AMIRA P9 project through research contributions by the Julius Kruttschnitt Minerals Research Centre (JKMRC, Brisbane, Australia), University of Cape Town (UCT, Cape Town, South Africa) and McGill University (Montreal, Canada) has been successfully commercialised through JKTech. The methodology involves detailed flotation plant campaigns which require large quantities of data to fit models that can be used in JKSimFloat (a steady state simulator for the flotation process). The methodology to date, although widely accepted as the best flotation optimisation technology available, is limited to existing circuit optimisation and requires full plant or pilot plant data to calibrate new models. The floatability of new ore types cannot be characterised using this method unless a pilot campaign is undertaken. After reviewing a large database of existing industrial floatability data, a new methodology is proposed that involves a laboratory based flotation test procedure and review of the floatability database to characterise the floatability of new ores. The full methodology is labelled the floatability index test procedure (JKFIT). This paper outlines the JKFIT procedure and the results of applying this methodology to pilot plant data from a copper ore. JKFIT was applied to two different feed sizes (namely a P80 of 180 microns and 212 microns) of this copper ore. The results of applying JKFIT to this case showed that the metallurgical response (in terms of grade and recovery) from the full pilot plant survey data could be predicted well. Further validation of this methodology was conducted on a separate copper ore. The results from this validation also showed that the JKFIT test was able to be used to predict the full plant performance. The JKFIT test has the potential to become the 'drop weight' test of flotation which will improve the confidence in plant design flow sheet layouts, allow full orebody characterisation and prediction of key grades and recoveries before the ore enters the plant, and will provide an improved methodology for chemistry impact analysis on different ores.

Jan 1, 2008

By Ali Kucuk, Bekir Karasu, Keriman Karaveli Pekkan

"Zircon (zirconium silicate) is the main opacifier of glossy, opaque, white colored, frit-based wall tile glazes. However, zirconia containing frits employed in the preparation of these glazes increase the production cost and therefore, limit zircon usage as a raw material at industrial scale. With the present study, it was searched whether borax solid wastes could be evaluated as a component in the starting relevant frit recipes. The wastes were obtained from Eti Maden Kirka Boron Company of Turkiye. Frit production, glaze preparation, application, and fast single-firing of glazed wall tiles were conducted under laboratory working conditions in Anadolu University, Department of Materials Science and Engineering laboratories. Beside standard tests applied to the final glazed wall tiles, color and gloss analyses of the fired glazes were conducted with a spectrophoto-meter and a gloss-meter. Characterization of these newly produced glass-ceramic glazes was made by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) techniques. IntroductionFrits are the indispensable constituents of most industrial glazes which mature at temperatures below 1150 °C [1]. In the traditional opaque glazes used in wall tile industry, opacity usually originates through hardening of glass matrix by adding high amounts of zirconia containing frits into the glaze batch [2]. Nowadays, researches point out that certain type of glass-ceramic layers can be alternatively employed as tile coatings lowering the use of zirconia containing expensive opaque frits. A rather high crystallization capacity of glass- ceramic glazes due to zirconia presence in glass network makes them suitable candidate as a glaze coating with a desirable micro-structure. One of the best methods to obtain an opaque glaze surface is to induce a crystal phase in the coating, whose refractive index differs significantly from that of the glassy matrix. The opacity of such coating is determined by the diffusion, refraction and reflection of light through the layer containing emerging crystals, and the degree of opacity mainly depends on the size and quantity of crystals. The development of glazes not consisting of expensive or toxic components is of special interest [3]."

Jan 1, 2008

By Kathleen M. PH. D. Kowalski

This paper discusses human judgment and decision-making under stress. The authors review selected recent literature across various disciplines and suggest a definition of stress within the context of decision-making during the management of emergencies. They also discuss fieldwork by the Pittsburgh Research Laboratory, NIOSH, which explores traumatic incident stress, the relationship between previous training and performance under stressful conditions, and human behavior in underground mine fires. The authors assert that stress is one of the factors that decision-makers must contend with in most life-or-death situations. They suggest that a better understanding of individual's judgment and decision-making activities while under stress would yield a better understanding of how people reach the choices they make in emergencies. This enhanced understanding would be of enormous value to emergency managers, researchers, and policymakers.

Jan 1, 2008