Search Documents

The last decade has seen the use of powerful computerized Mine-Wide Monitoring (MWM) systems for detecting hazardous conditions in underground coal mines. Recently, the U.S. Bureau of Mines and Jim Walter Resources, Inc. (JWR) expanded the scope of MWM system to include ground control. Single-point extensometers were installed in each of 30 intersections along a tailgate entry. These instruments monitored the rate of roof sag, a sensitive indicator of roof instability. Data were collected by the mine's own computerized MWM system. The paper describes the successful integration of ground control instruments into MWM, the data reduction procedures, and the identification of several hazardous areas.

Jan 1, 1994

By D. A. Bird

Geochemical models using published thermo-dynamic data and laboratory derived kinetic rate laws allow prediction of post-closure pit lake geochemistry at open pit mining sites. A combination of "forward" and "inverse" modeling techniques can predict the pit lake geochemical evolution from initial infilling to eventual steady state attained decades or centuries after closure. Computer codes have been developed to model chemical reactions such as pyrite dissolution, describe the ground-water flow regime, and provide rock-water ratios. The incorporation of site specific information, such as ultimate pit dimensions, geologic and hydrologic data, acid generating potential (AGP) vs. acid neutralizing potential (ANP), and laboratory derived kinetic rates, allows application of the model to open pit mines at any stage of development.

Jan 1, 1994

In parallel work, the cyanide/silver impregnated activated carbon system was studied for the purpose of developing an alternate cyanide removal system. It was found that free cyanide can be reduced from 20 ppm to below 10 ppb with a fixed bed of silver impregnated activated carbon, since such cyanide removal might be applicable to gold mill effluents, the investigation was extended to the cyanide/gold impregnated activated carbon (GIAC) system. Batch tests were conducted varying the gold content of activated carbon, carbon/CN ratio, stirring speed, pH of the initial solution, and the reaction temperature. The adsorption isotherm of cyanide/gold impregnated activated carbon system was also studied. The results of these batch tests show that the behaviour of the cyanide/GIAC system is very similar to the cyanide/silver impregnated activated carbon system variation of the gold content of the impregnated activated carbon has some influence on the cyanide adsorption rate. The latter is mainly increased, however, by increasing the GIAC/CN ratio. The activation energy was determined to be 3.12 kca1/mole (13.08 kj/mole) and the Au(CN)2 saturation at 194 µ M/g NORIT ROX O.B. The experimental results of reaction temperature and stirring speed show that the adsorption of free cyanide on such activated carbon is controlled by pore diffusion inside the activated carbon particle or by surface reaction. The adsorption isotherm follows the linear model and it is favourable for the cyanide/gold impregnated activated carbon system.

Jan 1, 1994

By J. Kallioinen

Flotation of low grade Ni ores with serpentinite host rock tend to yield low recoveries of Ni With high MgO contents in the concentrate. The recovery can be enhanced by optimizing the sub-processes in the pulp and in the froth. The new OF-100 flotation cell has been designed to be adaptable to different feed fineness (Coarse, Fine). The losses can according the research conducted at Outokumpu's Hitura plant be substantially decreased by OF-100's new rotor and stator design and froth zone geometry. The froth residence time is used to adapt for feed particle size changes measured by the Outokumpu PSI- 200. Models for the behaviour of different particle Sizes in the sub-processes have been developed. The modified froth zone geometry and the capability of maintaining a froth of desired thickness allows efficient washing of the obtained concentrate producing low levels of MgO.

Jan 1, 1994

By Rajesh S. Ransing

An intelligent tool has been developed to analyse the quality of diecast components. The influence of both design and process parameters has been studied in great detail. The tool, based on expert systems related technologies, can identify the causes for the defective castings manufactured. Design related causes such as gate position; gate area, runner design etc. as well as process related causes such as cycle time, cavity filling time and melt temperature are suggested by analysing the data on defective castings for a manufacturing campaign. This intelligent analysis is useful for both design as well as production engineers in the decision making process. All the causes for the occurrence of defects are classified into two categories. The firs category is the 'rootcauses' i.e. the causes which are related to the actual process, material and design parameters and which can be directly monitored. The second category is more abstract in nature and is classified as `metacauses'. These capture the scientific rationale implicit in the cause and defect relationships. This knowledge on causes and defects is represented in the form of a structured graph rather than by a set of rules, which, coupled with forward reasoning and heuristic search techniques results in an elegant and efficient approach. Uncertainties and the degree of relationship among causes and defects are represented by a fuzzy probabilistic model.

Jan 1, 1994

By Dean H. Ambrose

The U.S. Bureau of Mines recently developed computer graphics simulations to characterize mining scenarios, specifically for room-and-pillar mining operations in a three-entry longwall development section. These simulations compare productivity between shuttle car and continuous haulage systems concepts. One of the continuous haulage systems concepts has bolting capabilities that supplement haulage function. Simulations showed the continuous haulage system to be more time efficient than the shuttle car system. Researchers can reuse the simulation code (e.g., mining rates and equipment capacities can be changed) should investigators care to compare production of other mining scenarios. computer simulation, found computer model modification flaws and mining scenario conceptual errors. The fundamental rationale for three-dimensional computer is to cheaply, easily, and quickly obtain information about operation and of a current or proposed mechanical coal or metal/nonmetal mining system. This report documents the computer graphics model and simulation developments and discusses some of the results and observations from the simulations.

Jan 1, 1994

The future phosphate rock deposits in South Florida contain a significant fraction of dolomite. The high MgO content of the rock is undesirable in the production of phosphoric acid. Several flotation schemes have been attempted to separate dolomite from phosphate rock. Alternately, Selective Flocculation process has been suggested to separate dolomite from apatite. A high MgO content rock was simulated by a 30:10:60 synthetic mixture of apatite, dolomite and silica. Single mineral selectivity was observed in the mixed mineral systems apatite-silica and dolomite-silica with Polyacrylic acid (PM) and Poly(ethylene oxide) (PEO) flocculants respectively but not realized in apatite-dolomite system with PEO flocculant. Heteroflocculation, suspected to be the major reason for loss in selectivity, was minimized by addition of a Site Blocking Agent (lower molecular weight fraction of PEO). Process parameters such as size reduction schemes, flocculant/SBA dosage, and pH were investigated to achieve the desired separation. The selectivity obtained in binary mixed mineral tests was translated into the ternary mixed mineral system, viz. apatite-dolomite-silica. In this presentation surface chemical characterization of the samples and their flocculation behavior will be discussed.

Jan 1, 1994

By P. Songfack

In this work, the slurry flow in the ball mill is solved with Navier-Stokes' equations and the marker and cell technique (MAC), which tracks the fluid-free surface. Considering different planes in the radial and axial directions, this numerical approach leads to the direct calculation of the slurry velocity profile, mill holdup, and volumetric flow in the ball charge and pool. The MAC technique takes as input, the results of a direct three-dimensional simulation of the motion of grinding media, and in turn, provides a detailed knowledge of the hydrodynamics of slurry flow through the porous structure of ball load. This technique is a new approach to the mass transport problem that overcomes the limitations of indirect studies such as residence time analysis and holdup measurements.

Jan 1, 1994

By C. L. Karr

The efficient management of the distribution of goods and services is important throughout the minerals industry. From the scheduling of processing plant operations, to the routing of work crews in mines, to the planning of product development, vast amounts of time, energy, and money are wasted due to poor planning and scheduling. Thus, the U.S. Bureau of Mines is investigating computational algorithms that can be used to minimize the economic losses related to scheduling and allocating resources. Although there is commercial software available for tackling many scheduling problems, there has been little relief provided for solving the difficult traveling salesman with time windows problem (TSTW). The TSTW problem is a "derivative" of the classic traveling salesman problem, and can be used to minimize the distance traveled by vehicles or personnel to visit all points on a tour, with the additional constraint that each point on the tour must be visited within a specified time window. This paper is a survey of published work in which genetic algorithms have been used to efficiently solve the traveling salesman problem and its more difficult derivative, the TSTW problem. A genetic algorithm is a search algorithm based on the mechanics of natural genetics, and has been used to solve a broad spectrum of engineering optimization problems. Results indicate that the versatility, searching power, and simplicity of genetic algorithms can be used to provide substantial improvement in the area of scheduling and resource allocation.

Jan 1, 1994

By N. A. Barcza

DC plasma-arc technology using a hollow graphite electrode (cathode) has been successfully implemented in the primary metallurgical industry in South Africa up to the 30 MW scale. Mintek has applied its expertise base, established over the past fifteen years, to testing the treatment of metallurgical wastes such as carbon- and stainless-steel plant dusts, lead- and zinc-containing slags, and residues from the base-metal industry. Favourable results have been achieved, and disposable products were produced. The evaluation of numerous wastes indicates that recovery of zinc as metal gives the best economic return from these sources. Direct recovery via a splash condenser or electrolytic zinc extraction from fume are the two preferred alternatives under review. In both instances dehalogenation is an important issue, but can be achieved by suitable treatment processes. The Enviroplas technology provides a flexible, commercially viable approach to the treatment of a wide variety of wastes. Mintek, together with its associate Pyromet CC, are installing a plasma- arc pilot-plant facility with both an ISP lead-splash condenser of about 5 t/d condensed zinc capacity and a combustion chamber to burn zinc vapour to zinc oxide. This will demonstrate the suitability of the Enviroplas technology for treating specific metallurgical wastes, so that customized industrial plants can be engineered based on large-scale testwork.

Jan 1, 1994

This report on the Venezuelan coal industry is the seventh in a series of studies on coal exporting countries requested by the House Appropriations Committee, The committee asked that the basic differences in mining costs for U.S, and foreign mines be identified, especially those costs incurred in complying with health, safety, and environmental regulations.1 Basic costs in extracting raw coal are analyzed in this report for surface operations, This report also provides a limited analysis of the relative market competitiveness of selected Venezuelan and U,S. steam coal mines in three electric utility markets: New England and the east coast of Florida in the United States, and western Europe. Although some Venezuelan coal has coking characteristics, all coal-producing regions of Venezuela sell coal in steam markets.

Jan 1, 1994

By I. Gaballah

The chalcopyrite ore's anodic and cathodic electrodissolution are studied using a Porous Pulsed Percolated Electrode (3PE) reactor. Stationary solid electrode experiments are also performed to explore the mechanism of electrochemical dissolution of chalcopyrite. Experiments with a low - grade natural ore have been carried out at 25 "C in solutions containing 1 M NaCl and 1 M HCl. Galvanostatic and potentiostatic conditions are employed. The influences of current and potential on selectivity of the chalcopyrite ore dissolution are assessed. Anodic oxidation of this ore leads to a preferential dissolution of iron bearing minerals, whereas cathodic reduction is more selective with respect to chalcopyrite. However, in both cases the electrochemical dissolution is incomplete and the current efficiency is low. Design of the actual reactor has to be modified to increase the bed conductivity and to allow continuous experimentations.

Jan 1, 1994

By B. Kolonja

This paper considers simulation of truck dispatching system designs using maximum expected production of the truck-shovel system as the measure of performance. Two methods are utilized, multiple comparisons with the best (MCB) and the combination of MCB and the variance reduction technique known as common random numbers (CRN). These two techniques are compared via simulation experiments. The results show that the combined procedure of MCB with CRN is the superior tool to reduce the total number of replications needed to ensure the specified probability of correct selection over the finite number of designing systems. In this case study, MCB with CRN reduces the variance by 29% and the number of required replications by 48%. Also, the MCB with CRN procedure narrowed the confidence interval by 18%.

Jan 1, 1994

By S. J. Jung

The stability of underground openings for deep mines is critical, since incorrect orientation or geometry of shaft, stope, and accessways often results in the failure of openings due to high stress concentrations. Current state-of-the-art procedures for the design of underground openings are largely based on rules of thumb, experience, and trial and error. Rules of thumb are invariably based on the past experience of the designer and may not remain optimal as the depth and complexity of mine workings increase. Often, as conditions change, and as the interaction between geology, in-situ stress conditions, and mine openings grows more complex, the cost of maintaining structural integrity becomes prohibitive. Existing design procedures for deep mines are rapidly becoming inadequate as mines are worked at greater depths. For example, in the Coeur d' Alene Mining District, several million dollars are spent for inspection, repair, and maintenance on a regular schedule, largely as a result of inadequate design. In these types of situations, it is of critical importance that a new design methodology be developed for the layout and design of underground openings.

Jan 1, 1994

By Gordon T. Austin

Garnet is the general name for a family of complex silicate minerals having similar physical properties and crystallizing in the isometric (cubic) system. All garnets have the same general chemical formula but vary greatly in chemical composition. The name garnet is derived from the Latin word granatus, meaning like a grain, which refers to the mode of occurrence wherein crystals resemble grains or seeds embedded in the matrix. GEOLOGY Mineralogy Chemical Properties: The general formula for garnet is A3B2(SiO4)3, whereas A can be calcium, magnesium, ferrous iron, or manganese, and B can be aluminum. ferric iron, or chromium, or rarely titanium. The formulas and names of common garnet species are: [ ] Almandite and almandite-pyrope solid solution garnets are the best abrasive types, but andradite, grossularite, and pyrope also are used. All species of garnet have been used as gemstones. The structure of garnet consists essentially of isolated SiO, tetrahedra connected by oxygen-cation-oxygen bonds through the distinct A and B group cation sites. Within this structure magnesium, ferrous iron, and manganese easily interchange and substitute for each other in the A cation position, and calcium does so less readily. Additionally, aluminum, femc iron, and chromium substitute for each other to a limited extent in the B cation position. This ability to substitute or exchange ions without changing the crystal structure is called isomorphism, and garnet is one of the finest examples of a isomorphous series. Because of this isomorphism there is complete solid solution between certain garnet species but not between others. Fig. 1 illustrates these solid solution relationships. Some rare species of garnet are known that illustrate the wide range of cation substitution that the garnet crystal structure can accommodate. They include: [ ] These rare species are not of interest for industrial applications, but can be of interest to mineralogists and the gem industry. Physical Properties: Garnet displays the greatest variety of color of any industrial mineral. Garnets have been found in all colors except blue. For example, grossularite can be colorless, white, gray, yellow, yellowish green, various shades of green, brown, pink, reddish, or black. Andradite garnet can be yellow- green, green, greenish brown, orangy yellow, brown, grayish black or black. Pyrope is commonly purplish red, pinkish red, orangy red, crimson, or dark red; and almandite is deep red, brownish red, brownish black or violet-red. Spessartite garnet can be red, reddish orange, orange, yellow-brown, reddish brown, or blackish brown. A few garnets exhibit a color-change phenomenon. They are one color when viewed in natural light and another color when viewed in incandescent light. Because of the great variation in color of garnet within each species and similarities in color between garnets of different species it is recommended that garnet identification not be based on color alone. The Mohs hardness of garnet varies from 6.5 to 9.0. Grossularite and uvarovite have a hardness of 6.5 to 7.5; andradite is 6.5 to 7.0; and pyrope, almandite, and spessartite are 7.0 to 7.5 in hardness. There are reports of almandite having a hardness of between 8.0 and 9.0. As with hardness, the specific gravity of garnet varies considerably. The specific gravity may be as low as 3.2 or as high as 4.3 depending on chemical composition. Garnet crystallizes in the isometric system with rhombic dodecahedra and trapezohedra the most common forms. Crystals also form in combinations of dodecahedra and trapezohedra or either of these in combination with hexoctahedra. Crystals can have cubic or octahedral faces, but these are rare. Under favorable conditions of formation garnet will crystalize in nearly perfect forms that rival study models. Garnet also forms as irregular blebs, grains, knots, or masses, with or without distinguishable crystal faces, and as coarse- or fine-grained granular masses that appear to be totally lacking in crystal form. The fracture of garnet also shows great variation. In some garnets, particularly those that are well crystallized and glassy in appearance, the fracture is subconchoidal to conchoidal. Other, more poorly crystallized garnets exhibit a fracture that can only be described as uneven. Garnet occasionally has an indistinct dodecahedral cleavage. Certain species of garnet from specific locations have a pronounced laminated structure consisting of planes of weakness along which parting takes place. This parting may resemble cleavage, but since it is mechanical and not related to crystal structure it is not true cleavage. The optical properties of garnet are sensitive to even small changes in chemical composition or strain in the crystal structure. For this reason each species does not have a single index of re- fraction (IR) but has a range of 1Rs. Uvarovite in its pure form should have an IR of 1.870, but in nature samples vary from 1.74

Jan 1, 1994

By John L. Nieber

This information circular describes a computer program called VARSAT2D, a comprehensive unsaturated fluid flow simulator developed by the U.S. Bureau of Mines. VARSAT2D solves for either a vertical or horizontal, transient or steady-state solution in variably saturated, heterogeneous, anisotropic porous media using the Galerkin finite-element approach. Simplex triangular elements are used. Moisture retention characteristics are described by specifying either the Brooks and Corey, Brutsaert, or Van Genuchten power functions, with hysteresis described using the Maulem independent domain model. Boundary conditions may include any combination of time-varying seepage, pressure along solution domain, boundaries and/or at internal node points, unit hydraulic gradient at the lower boundary, and a uniform source and/or sink. This program should be a welcome addition for mining and environmental hydrologists, researchers, and engineers interested in modeling unsaturated fluid flow.

Jan 1, 1994

By V. T. McLemore

The Steeple Rock district is a major epithermal .gold-silver district in New Mexico that exhibits district zoning. Five types of ore deposits occur in the district. The base-metal veins (with Au and Ag) form the center of the district and occur along the Carlisle fault. The gold-silver veins occur along northwest-trending faults outward from the base-metal veins. The margins of the district are formed by copper-silver, fluorite, and manganese veins. In addition, areas of older acid-sulfate alteration occur throughout the district and also exhibit zoning: massive silica/chert zone (inner), silicified zone, and clay zone (outer). This alteration overlies regional; alkali-chloride (propylitic to argillic to sericitic) alteration. Synthesis of available data suggests the acid-sulfate alteration is related to a shallow but older epithermal hot springs system. Subsequently, younger epithermal veins formed along faults.

Jan 1, 1994

By E. L. Bohnet

The purpose of this paper is to translate a mining company's "Corporate Objectives" into usable and practical guidelines for long term mine design and production scheduling. These guidelines are required to ensure that both operating and development properties are designed and economically ranked on the same basis, and with the "current" Corporate Objectives in mind. Secondly, if both management and mining engineers have a better understanding of the cause and effect of corporate policies, then penalties and risks associated with various Corporate Objectives can be put into better perspective for management. Corporate Objectives, relative to usable guidelines for either short and/or long term mine planning, could be defined as one or more of the following four objectives: 1) Maximize the recovery of the economic portion of the defined geologic resources, and hence, maximize total non-discounted project cash flows and profits (most common approach in mine design), 2) Maximize the Net Present Value (NPV) of the after-tax cash flows from each existing or proposed project, either on an individual basis or in concert with other projects, including downstream processing facilities (primary method used to judge relative investment merit of a proposed development or operating concept), 3) Limit short and long term capital expenditures to a defined ceiling, 4) Maximize product output for the existing facilities in the short term, or conversely, keep commodity production at a constant level for a series of years.

Jan 1, 1994

Provide longwall operators with practical information and guidelines concerning mine design to reduce problems associated with the interaction of adjacent workings in multiple-scam longwall mines. Background The high productivity achieved by longwall mining demonstrates its potential to provide a substantial segment of underground coal production. Longwall mines produce more than 30 pct of underground coal, up from pct just 15 years ago. However, the continued growth of this mining method without appropriate multiple-seam planning may increase the cost and risk of mining. Research by the U.S. Bureau of Mines (USBM) indicates that 25 longwall mines (32 pct of the total number in the United States) have mining in adjacent coalbeds either above or below. About half of these longwall mines report some type of interaction problem with the adjacent workings, such as caving due to subsidence. Optimization of mine design factors is the best means for controlling interactions between operations in adjacent scams. To avoid higher mining costs, operators should focus on adopting practices and procedures that prevent and control interactions in multiple scams. The USBM, in an effort to improve longwall mine planning, has been investigating multiple-seam longwall design and development.

Jan 1, 1994

By Richard L. Unger

The Crewstation Analysis Programs (CAP) is a package of computer programs that can be used to analyze some human engineering aspects of crewstation design (such as visibility and illumination) that have particular significance in underground mining. It was developed under the U. S. Bureau of Mines (USBM) Health, Safety and Mining Technology program at the Pittsburgh Research Center, Pittsburgh, PA. This manual describes the steps necessary to collect data in the laboratory to develop luminaire profiles for the CAP illumination analysis. It also describes how the CAP Illumination Model calculates illumination. 1.1 How CAP Calculates Illumination 1.1.1 Background -CAP currently includes assessments of visibility and illumination in the surrounding work area. The advantage of using computers for these types of analyses is that many design iterations can be tested quickly and efficiently to learn the effects of changes. This reduces the need for expensive testing using physical mockups. Another advantage is that design ideas can be tested in situations where it would not normally be possible. For instance, the effects of modifications to a lighting system or canopy design on visibility could be tested while the machine remains in service.

Jan 1, 1994