Search Documents

By L. M. Chan, D. H. Carlson, J. B. Johnson

"Abstract — Concentrations of tailpipe pollutants from diesel-powered. underground mine vehicles change over time due to engine wear and the need for maintenance. Since this deterioration in pollutant emissions may adversely affect the air quality in an underground mine, it should be monitored and controlled. This paper presents decision criteria concerning when to service a mine vehicle diesel engine. These criteria, based on mine air and tailpipe concentration measurements, are designed to maintain the tailpipe concentrations within limits that assure satisfactory mine air quality.Application of the deterioration criteria to mine vehicle emissions involves:establishing, for each pollutant, the allowable deterioration factor, anddetermining the deterioration factor, from the mine air and tailpipe diesel pollutant measurements, and the mine air threshold limit values (TLVs).If the deterioration factor is greater than or equal to the allowable deterioration factor the vehicle is removed from service for maintenance.An analysis applying the criteria to measurements made in an underground coal mine is presented. The tailpipe pollutant concentration data were collected using the Emissions Mea-surement Apparatus (EMA) developed by Michigan Techno-logical University. Since the TLV for diesel particulate matter (DPM) has not yet been established assumed mine air DPMTLVs of 15 and 1.0 mg/m3 were used in the analysis. For all of the diesel haulage vehicles included in the analysis. DPM was found to be the critical pollutant (the one most in need of control). For an assumed mine air DPM TLV of 15 mg/m3 none of the diesel haulage vehicles would he removed from service. However reducing the DPM TLV to 1.0 mg/m3 would make it necessary to remove two of the three vehicles tested from service."

Mar 1, 1992

By E. D. Regad, W. E. Wallace, P. S. Mike, C. A. Hill, V. Vallyathan, M. J. Keane

"Respirable-sized quartz, a well-established fibrogenic mineral dust, is compared with kaolin in erythrocyte hemolysis assays aher treatment with saline dispersion of dipalmitoyl phosphatidylcholine, a primary phospholipid component of pulmonary surfactant. Both dusts are rendered inactive after treatment, but the membranolytic activity is partly to fully restored aher treatment with phospholipase Ai. an enzyme normally associated with cellular plasma membranes and lysosomes. Phospholipid-coated dusts were incubated for periods of 2-72 h at a series of applied enzyme concentrations, and the adsorbed lipid species and hemolytic activity were quantitated at each time for both dusts. Surfactant was lost more readily from quartz than from kaolin, with consequent more rapid restoration of mineral surface hemolytic activity for quartz. Interactions of surfactant and mineral surface functional groups responsible for the mineral-specific rate differences, and implications for determining the mineral surface bioavailability of silica and silicate dusts, are discussed. INTRODUCTIONMineral particles depositing in the lung acinus will contact an aqueous coating containing surfactant molecules spread on the air-liquid interface and dispersed within this hypophase; the primary components of that surfactant are diacyl lecithin phospholipids (King and Clements, 1972; King, 1982). Adsorption of this surfactant can suppress the cytotoxicity of mineral dusts (Marks, 1957). Suppression of hemolytic activity, a measure of membranolytic potential and an indicator of bioavailability of the mineral surface, of respirable-sized quartz and kaolin clay dusts with the adsorption of dipalmitoyl glycerophosphorylcholine or dipalmitoyl lecithin (DPL) has been measured (Wallace et al., 1985). Such contact and adsorption of pulmonary surfactant in vivo may provide a first defense system of the lung against respired dusts."

Mar 1, 1992

By D. A. Lucero, J. E. Brockmann, L. A. Mondy, K. L. Rubow, D. J. Rader

"Department of Mechanical Engineering, University of Minnesota, Minneapolis, MNExperimental and correlated stage responses (the fraction of particles entering an impactor that are collected on a stage) are presented for the Andersen Mark III and Marple personal cascade impactors. The impactors were operated upright and fully assembled so that interstage interference and wall losses could be properly studied. The observed stage responses showed maxima that fell significantly short of unity, meaning that a monodisperse aerosol is never collected exclusuvely on one stage, but is distributed among several stages and internal losses. Correlations for the stage responses are presented so that the experimental results can be used to determine size distributions with available data-inversion algorithms. Simulations with log-normal distributions show significant differences between dpa50 histograms and the more accurate distributions that result by taking the response functions into account.Cascade impactors are widely used for the measurement of aerosol size distributions; their ruggedness and simplicity of operation make them an attractive choice for a variety of environments. In one common application, the aerosol of interest is drawn through the impactor, and the amount deposited on each stage is determined gravimetrically. The primary objective is to extract as much information as possible about the initial size distribution from the resulting set of weights. Unfortunately, the reconstruction of contin-uous size distributions from finite data sets is an ill-posed problem. Not surprisingly, a variety of such reconstruction techniques are presently in use; the success of each method depends on the particular nature of the aerosol sample and the instrument response.Inversion of impactor data by any of these techniques requires that the response functions for each stage be known. The stage response function gives the fraction of particles entering the impactor that deposits on that stage. Values of the response function range from zero to one, and depend on impactor operating conditions (e.g., geometry, flow rate, and gas properties) and particle properties (e.g., diameter, density, and shape factor). As interstage interferences and particle losses will affect each stage's response, experimental determination of stage responses should be made for fully assembled impactors. Unfortunately, impactor stage response functions are rarely reported; rather, single-stage efficiency curves are given that provide an incomplete description of impactor performance.This paper presents experimental stage responses for two fully assembled cascade impactors: the Andersen Mark III and Marple personal impactors (model 298, Andersen Samplers, Inc., Atlanta, Ga.). These calibrations were performed with monodisperse liquid droplets for both impactors and also with monodisperse solid spheres for the Marple personal impactor. The calibration results for the Mark 111 impactor presented here have been previously reported in the response-function format (Rader et al., 1989). The calibration results for the Marple personal impactor, however, were originally presented in the single-stage efficiency for¬mat (Rubow et al., 1987) and have been reanalyzed in this work. Losses within both impactors are considered, and their treat¬ment within data inversion techniques is dis¬cussed. In addition, correlations for each impactor's response functions are presented so that these calibration results can be easily included in data-inversion algorithms. Size distribution inversions using these response correlations are compared with the standard cut-point method for two lognormal test dis¬tributions."

Mar 1, 1992

By J. Ostwald, L. T. Matthews, C. E. Loo

Australia has large reserves of pisolitic limonite. Mining recently commenced on the Yandicoogina deposit to produce a high-grade sintering ore. The ore contains about 10 wt% combined water and simulated sintering temperature profiles indicate that progressive dehydration of ore particles occurs in the temperature range 300-700 degrees C. Studies by optical microscopy show that although the dehyrdrated ore particles contain numerous cracks, there is no change in the microstructure of the ore because topotactic transformation to haematite results in the formation of compact masses of very fine-grained haematite microcrysts. When the ore is held at around 1 200 degrees C for 1 min significant recrystallisation of these microcrysts occurs, resulting in the formation of optically visible, micrometre sized haematite crystallites. Studies to simulate the behaviour of ore particles during sintering (as nuclear particles surrounded by a standard adhering fines mixture) show that the recrystallisation process occurs much earlier at temperatures of about 900 degrees C. Further studies indicate that CaO in the adhering fines mixture enhances the recrystallisation of the ore nuclei. The results of the investigation indicate that the pseudo-relict haematite in sinters produced from ore blends that contain significant levels of pisolitic limonite consists of dehydrated goethite that has undergone significant recrystallisation and grain growth, a phenomenon that is facilitated by the presence of lime derived from the sintering melt.

Jan 12, 1992

By L. J. Barnes, R. O. Koch, J. H. Versteegh, C. J. N. Buisman, P. J. H. Scheeren

Several water treatment options have been studied and piloted. A process based on activity of sulphate reducing bacteria combines sulphate removal and heavy metal removal in one process step. The anaerobic bacteria reduce the sulphate to sulphide and consequently metal sulphides will precipitate. The final design for the commercial scale plant is described.

Jan 12, 1992

By NA NA

Reports of discussion at sessions held in Keyworth, UK, on 22-23 April 1992.

Jan 12, 1992

By D. J. Reddish, B. N. Whittaker, G. X. Sun

An image analysis technique has been used in the assessment of subsurface fracture levels in the context of water inflow into longwall mine workings. The technique was used to analyse results from physical modelling which are represented by black and white photographs taken directly from the model tests. Binary images of fracture patterns are obtained by scanning the photographs with an image analyser coupled to a video camera. The images are manipulated by a C program which allows them to be processed in vertical and horizontal directions and filtered to differentiate quantitatively between vertical and horizontal fracture intensities. The fracture density distributions provide a valuable database for further numerical and statistical analysis. This allows assessment in terms of water inflow into the excavation. A comprehensive image analysis was undertaken on several extraction models. Results indicate that extraction thickness has a significant effect on the fracture pattern and the fracture density distributions. The results can be used to adapt model findings to situations with a range of extraction thicknesses. The technique has allowed improvement in image enhancement and in the interpretation of model results. In particular, a qualitative comparison between different models is possible.

Jan 12, 1992

By A. B. Holland-Batt

Deposition velocities play an important role in many fields of engineering and an impressive range of measured data has accumulated in the literature. Numerous workers have addressed the problems that are associated with the prediction of deposition velocity because of its particular relevance to the design of pipelines and pumping stations. However, despite this extensive effort, the calculation of friction heads still requires reference to experimentally based graphs to determine Durand factors and there is still scope for improvement in the prediction of the deposition velocity at different solids concentrations. Equations to characterise the relationship between the Durand factor and the volume concentrations of solids in the slurry are presented. A correlation for the prediction of the deposition velocity is also developed and tested against some of the classical experimental data. The application of predicted values of deposition velocity in assessing the potential for the sanding-up of spiral separators is then described and a case study is presented.

Jan 12, 1992

By A. H. G. Mitchell

Gold-poor and gold-rich porphyry and epithermal gold-silver deposits of Caenozoic and Cretaceous age in the western Pacific and central and eastern Europe are confined to predominantly andesitic continental margins and island arcs. The arc volcanic rocks overlie a complex non-oceanic basement of stacked nappes, the uppermost of which is often ophiolitic. The emplacement of ophiolite triggered a reversal of tectonic polarity, subduction and arc magmatism. Andesitic volcanism and the formation of a strato-volcano were followed by the ascent of magma and porphyry copper mineralisation. Regional propylitic alteration came from convecting, predominantly meteoric fluids. Magmatic degassing caused advanced argillic alteration. This is commonly unmineralised in perched water tables, but may sometimes host high sulphidation gold or enargite gold at deeper levels within the propylitic zone. The onset of extensional stress after the andesitic volcanism allowed meteoric water to circulate to depths of 5 km or more, with consequent cooling of an ascending magma body at depth and the development of low sulphidation epithermal gold mineralisation near and immediately above the sub-volcanic basement surface. All andesitic arcs are mineralised. Regional controls on their ore potential include the level of erosion and geological features in the basement that focus the ascent of fluids. Differences between the mineralisation of the European and the western Pacific arcs may reflect the presence of older, more granitic basements in many of the European arcs.

Jan 12, 1992

By R. Vikram

IMAGES (Integrated Mapping Applications Graphical Evaluation System) is a computer graphics system developed by British Coal for mine planning. The objectives of the system are to increase the profitability of mined coal through a combination of direct and indirect benefits. The system is flexible and can be used in part or in full at a mine as a stand-alone system or as a remote location of a central corporate system.

Jan 12, 1992

By D. J. Buchanan

British Coal's mining research programme is directed towards the strategic objectives of reducing production costs, improving product quality and resolving health, safety and environmental issues. The strategy for R&D is described and selected parts of the programme are reviewed. Two major initiatives are directed towards reducing production costs: geotechnics and automation. Integrated exploration techniques are used to delineate geological structures as an aid to mine planning. Rockbolting is being rapidly introduced and the in situ stress field has been found to be of significant influence. Automation is the subject of a major programme. A strategy for coal quality has been devised. The health, safety and environmental programme concentrates on the traditional hazards together with surface environmental problems.

Jan 12, 1992

By M. J. Russell, W. E. Stephens, D. B. Mohamad, A. B. MacKenzie

Redox front processes in rocks are important in the context of both radioactive waste disposal and the development of orebodies. Results are presented from a study of the distribution of uranium and thorium and the natural decay series equilibrium about redox fronts in a granite at the Criffel pluton and Craignair quarry, Dalbeattie in southwest Scotland. The results are considered in the context of large scale uranium aqueous transport in the region and compared with those from a previous study of highly developed redox fronts at Pocos de Caldas, Brazil. Results show that the Criffel pluton has experienced a recent and rapid removal of uranium from the uppermost section of the granite whereas thorium has remained relatively immobile. The radium and uranium distributions indicate that diffusion processes probably control the distribution of radionuclides about the front. These processes are similar to those observed at Pocos de Caldas. The trends of concentration and activity ratio about the Dalbeattie redox front are less pronounced than those at Pocos de Caldas owing to the shorter time available for the process and the lower intensity of weathering at Dalbeattie.

Jan 12, 1992

By G. B. Hooper, G. A. Ferguson

The technical capabilities and user-friendliness of the major computer-aided mining design software systems are reviewed. Recent experiences with three systems are outlined to indicate the practical problems that arise. The examples were: Microlynx software from Lynx Geosystems at the Great Dyke platinum mine in Zimbabwe; Lynx software from Lynx Geosystems at a copper mine in central Africa; and PC-MINE software from Gemcom Services at an open-pit gold project in Western Australia. Difficulties in the use of mining design software has led to an alternative approach. Falconbridge, Canada, has developed an integrated mine-planning system on a CAD platform that encompasses ore reserve estimation, stope design, development layout and survey control. Future directions of computer-aided mining design using this basis are discussed. A major advantage of using mainstream software packages, such as spreadsheets, databases and CAD programs, is that most engineers and geologists are experienced in handling such systems in the normal course of their work.

Jan 12, 1992

By J. V. Wood, P. Davies, J. L. F. Kellie

A new range of wear-resistant materials is being produced by technology that has been used to develop high performance metal-matrix composites. These include steels and aluminium alloys that can be made as sheet, plate, rod or bar. The incorporation of hard, wear-resistant particles in an alloy matrix is achieved by reactive casting, spray deposition and powder metallurgical techniques. For example, large particles of TiC can be homogeneously distributed in steel during casting and the subsequent product can easily be rolled to plate. Similarly, up to 20% alumina particles and SiC can be injected, respectively, into steel and wear-resistant aluminium alloys by spray deposition. The current state of development of the process is reviewed and indications are given of the projected applications of such materials.

Jan 12, 1992

By G. J. Lyman

Mayer curves are used for process calculation in coal preparation. They can also be used to smooth washability data by fitting a hyperbola of particular properties to ash and yield, but to introduce the density variable an independent relationship with ash content must be adopted. When this ash-density relationship has a realistic form at low density, the implied form of the mass distribution function is unrealistic, suggesting that Mayer curves represented by a hyperbolic functional form are unsuited to coal washery calculations for low-density separations. Their use at higher densities is also uncertain. A similar conclusion can be anticipated when Mayer curves are used for other mineral systems.

Jan 8, 1992

By P. Danson, D. A. White, S. Bashir

Composite ion exchange materials made of SnO2, TiO2 and MnO2 can be used to remove radioactive contaminants from nuclear waste streams. In several cases their selectivity and capacity are enhanced by mixing hydrous silica into the matrix. MnO2-SiO2 materials are especially useful for a number of reasons, such as their selection of heavy elements over caesium. Distribution constants and determinations of exchange capacities show that in many instances the properties of the composites are better than those of the oxides alone, while the presence of a chelating agent has been found to reduce the uptake of nuclides considerably. Methods are being developed for the bulk manufacture of the materials. Further work on sorption mechanisms is required to explain anomalous results, particularly the variation in exchange capacity for different elements and the ability of the oxides to sorb colloidal material in alkaline solution.

Jan 8, 1992

By I. A. Scott, T. J. Napier-Munn

Size-by-size partition curves for mineral separation in dense-medium cyclones pivot about a single characteristic point. This is defined for stable, non-segregating media by the medium density and the proportion of the medium reporting to the underflow. The pivot point departs from these values for unstable, conventional media. The phenomenon can be represented by an equation with two parameters defining pivot point coordinates and two the Ep value. On the basis of experiments in a 200 mm cyclone using ferrosilicon media, simple regression equations were developed for the separation parameters in terms of operating conditions (the coefficients were likely to be site-specific). The experiments successfully decoupled the effects of medium density and viscosity and showed that the value of Ep was independent of the former but strongly dependent on the latter. A classification model was used to predict the density of the underflow medium, a knowledge of which is required to determine the pivot parameters. The model correctly reflects the performance trends observed in dense-medium cyclone operation and has the potential to be generalised to a wide range of industrial practice.

Jan 8, 1992

By R. Winand, P. Harlet

he cathodes produced are of electrorefined grade; metallographic structure and surface roughness are controlled to a depth of 1.3 cm (single-side deposits); silver levels in the cathode are regulated by the presence in solution of Cl- and Br- ions; organics must be used at very low concentrations (around 0.1 mg/l with a consumption of about 0.01 mg/l/hr). The required concentrations of additives were established according to a well-defined strategy based on the consumption of organics at the cathode by a mass transfer limited-process.

Jan 4, 1992

By R. Immele-Meziou, G. J. Long, D. G. C. Robertson, O. A. Pringle

The reduction of naturally weathered ilmenite concentrate occurs in two steps: reduction of Fe3+ to Fe2+, followed by reduction of Fe2+ to Fe. Small amounts of a magnetic phase were also observed and may correspond either to an Fe3O4-FeTiO3 ilmenite phase or to an Fe3O4-Fe2TiO4 spinel phase. The total amount of metallic iron produced after 12 hr was only 50% of the total iron present in the sample.

Jan 4, 1992

By R. G. Siddall, W. Gale

In the UK the development of the science of strata control has been strengthened by a resurgence of interest in the specialism of roofbolting and its associated techniques. The evolution of the theories and practices of strata bolting in roadway stabilisation is discussed. Practical experiences are considered, principally the use of Australian techniques, the relationship between bond strength and annulus and the effects of stress in the ground. Areas of new technology such as cable bolting, injection anchors and on-board bolters are also discussed. The recent advances in computer technology and rock testing equipment and methods have provided the opportunity to simulate ground behaviour under various conditions. Computer modelling developments and the use of techniques to predict ground behaviour are described.

Jan 4, 1992