Search Documents

By D. McCarthy

This paper discusses the process involved in developing an optimum method of treating and removing heavy metals from water that have leached out from the native rock -prior to discharge back into the environment. Also designed into the system is a manner to stabilize the metals removed as a precipitate, so that they can be disposed of as a non-hazardous waste.

Jan 1, 1992

By S. Tan

In this paper, several commonly used computer truck dispatching criteria are evaluated. A computer-oriented truck dispatching and production simulator was developed to provide data for comprehensive cross comparison among the dispatching criteria. The definitions, primary considerations, characteristics, and performances of these dispatching criteria were investigated. From the simulation results, it was concluded that, in general, no one criterion can dominate all others. All basic dispatching criteria including minimizing truck waiting time, minimizing shovel waiting time, minimizing truck saturation, maximizing truck momentary productivity, or truck routes optimization provide a local optimal solution. To obtain a direct global optimization solution for this complex stochastic process does not appear to be likely. Therefore, the search for an optimal dispatching criterion that will fit all conditions may not be realistic. However, based on the simulation results of the mine operation, several dispatching criteria which have good potential to increase performance can be selected. It may be necessary to search for the best combination of these truck dispatching criteria for a given situation. For example, a truck flow measurement such as the truck clustering factor at shovels can be used as a switch parameter to change from one criterion to another. The values for the switch parameter at which actions should be taken to change the criterion can be established through simulation programs.

Jan 1, 1992

By W. P. Barnett

In 1988, the U.S. Department of Energy's Pittsburgh Energy Technology Center identified three coal cleaning options for achieving flexible environmental control strategies aimed at reducing energy-related SO2 emissions. These are selective agglomeration, advanced froth flotation, and advanced cycloning. Each technology relies on maximum liberation of pyrite and other mineral matter through feed coal comminution to fine and ultrafine sizes. Research projects designed to expeditiously develop each of these technologies to the point of commercial viability were initiated. This paper will present the status of these projects and the application potential of each technology to coal beneficiation.

Jan 1, 1992

By P. G. Comba

Many gold producing states are requiring rinsing of spent heaps to render the leached ore compatible with the environment and are placing restrictions on effluent pa, cyanide, and metals concentrations. Parameters which may affect efficient rinsing of heaps have been investigated by the U.S. Bureau of Mines in laboratory column studies. Rinse profiles for cyanide, metals, and pH as a function of the volume of water passed through the spent ore are presented. Fresh water rinsing of spent ore in columns showed that rinsing of cyanide was not affected by the rinse solution application rate. Interrupted rinsing with a rest period between applications reduced the volume of water required to meet effluent cyanide concentrations. chemical oxidation of the effluent with recycle of the rinse solutions reduced effluent cyanide concentrations and the volume of waste solution generated. Water rinsing was not successful in reducing the alkalinity of the cement agglomerated ore. A dilute acid solution had to be applied after cyanide removal to reduce effluent pa levels to specified limits.

Jan 1, 1992

By J. Y. Hwang

Sands are utilized to make molds for metal castings in the foundry industry. Approximately a half ton of sand is disposed of for each ton of metal cast in this country. In Michigan, annual sand disposal amounts to about one million tons. A process has been developed in this study to reclaim sands from a steel foundry. Physical separations are utilized in conjunction with other operations (such as the removal of binder, metal, spruce, washes, etc.) to yield silica and chromite sands with desirable molding properties. Several different separation methods, including electrostatic, magnetic, and various gravitational approaches have been examined. Experimental results are presented. The applicabilities of these separation methods are discussed.

Jan 1, 1992

By J. C. Mullen

Today, the coal mining industry is more knowledgeable on the potential negative economic consequences associated with improper management of hazardous substances and various types of solid waste. The practices evaluated during environ-mental audits are discussed and example situations are shared from previous audits of coal mines and analogous situations. The importance of assessing and understanding purchasing, warehousing, safety, maintenance, electrical, operations, and environmental management practices and procedures is highlighted as a key to a successful and practical program. A waste minimization approach is presented including strategies for screening product purchases, product substitutions, and testing and record keeping.

Jan 1, 1992

By B. K. Mishra

This paper focuses on the use of a numerical tool known as the discrete element method (DEM) to study the motion of ball charge in ball mills (14-18 ft). DEM is employed to simulate the motion of individual balls. While doing so, the effect of liner design on the grinding performance of the mill is studied. Two important factors such as the configuration of the liner and the geometry of the lifting surfaces are correlated with the overall mill performance. An attempt is made to show the effectiveness of the lifter bars in transmitting power from the mill shell to the interior of the mill with particular emphasis to large diameter mills.

Jan 1, 1992

By Eoghan T. M Doyle

Oxide mixtures of nickel (NiO), cobalt (COO) and chromium (Cr203) were prepared with graphite in stoichiometric amounts and the powder mixtures were compacted to produce cylindrical pellets. The composition of chromium oxide in these mixtures were varied. Pressed pellets were reduced in a flowing stream of argon-4% hydrogen gas (500 ml/min). Both slow and rapid heating methods were adopted to raise the temperature of a pellet during reduction of oxides to form superalloy powder. The reduction temperature was varied between. 1523 and 1623K. The effect of heating rate and niobium oxide addition on the microstructure of the superalloy produced was studied by using ordinary light and scanning electron microscopes. New phases formed as a result of reduction were identified by X-ray powder diffraction technique. The mechanism of reduction of oxides together with the microstructure of NiCrCo alloy are discussed. The thermodynamics of formation of ternary alloy phase is elucidated on the basis of binary phase equilibria and Gibbs free energy of mixing data for the constituent alloy compositions.

Jan 1, 1992

By Heikki Tuovinen

The total utilization of raw materials and energy is the most important criterion when planning. industrial processes. The main goal is clearly to use the raw materials and energy as effectively as possible in order to make the desired products directly in the primary process itself', or to recycle unused materials and energy either as such, or after cleaning back into the process. However, few industrial processes are so straightforward. Most processes generate by-streams of materials and energy, which cannot be recycled directly and it is namely these by-streams which tend to remain as wastes. These by-streams are slags, dusts, vaporized metals, liquids, slurries, sludges, gases etc. Most base metal processes produce all these by-products. Waste water and gas emission controls and regulations are tightening all the time, so new processes must be developed to keep pace with these requirements. These processes generate more solid wastes, which must be utilized or at least processed into a harmless form landfilling. Municipal and hazardous wastes also contain valuable materials and energy, which must be used to minimize landfilling. The development of processes for these purposes places even greater demands on research and development. The same principles and methods developed for mining, ore dressing and metal refining processes can also be adapted for research and development work on processes for waste minimization. However, the problems encountered are much more complicated and less familiar, demanding more versatile and accurate tools and equipment. This paper presents principles, examples and some references of R & D work on processes for waste minimization.

Jan 1, 1992

By Liu Q, Siefken T. C, Misra V. N

Investigation of the differential flotation characteristics between arsenopyrite and pyrite in a ore concentrate have been carried out on a laboratory Leeds flotation cell. Experimental results indicate that some limited separation between arsenopyrite and pyrite is possible by differential flotation under the conditions of high pH and low pulp redox potential. The best performance in this testwork was achieved by using an oxidizing agent at pH 10.7. Of the oxidizing agents tested, NaOCI gave better oxidizing effect than KMnO4. It has also been observed that the pulp redox potential depends on the pulp pH value. At high pH values a hydroxide layer is formed on the arsenopyrite surface, which has the effect of a depressant on the arsenopyrite.

Jan 1, 1992

By Frank E. Federspiel

In 1992, the Bureau of Mines conducted a mineral resource investigation of the 78,000-acre Garns Mountain study area in southeastern Idaho. The area had been proposed for Wilderness. It is underlain by Paleozoic to Mesozoic-age sedimentary rocks about 11,000 feet thick. Rocks have been faulted, offset, and folded as part of the northerly-trending Idaho-Wyoming Overthrust Belt. Study area mineral occurrences are: phosphate in the Permian Phosphoria Formation; coal in the Cretaceous Frontier end Bear River Formations; and uranium in carbonaceous and phosphate-bearing shales and coal of these formations. Four zones of phosphate are estimated to contain about 528 mitt ion tons of rock with over 10% P205; samples of phosphate-rich rock also contained as much as 3950 ppm chromium, 3280 ppm vanadium, 23 ppm gallium, and 5540 ppm zinc. Fragments of poor-quality coal and carbonaceous shale were found in the area; coal was mined near the northeast border. Uranium content up to 0.016% U3O8 is in carbon-rich shales. Oil and gas were drilled for, with minimal success, in folded sedimentary rocks (frontier and Nugget Sandstone) in the Horseshoe anticline, near the east border. Examined workings included 12 dozer cuts, 4 trenches, 2 prospect pits, and 2 caved adits. No production is known, and no leases or claims are held for the area.

Jan 1, 1992

By Barbara C. Williams

U.S. Bureau of Mines researchers conducted field studies at an abandoned copper-gold mine tailings impoundment. Pore water quality was analyzed in the vadose and saturated zones. Three statistical procedures were employed to summarize the variability within and between the two zones. The results indicated that linear combinations of those variables reflecting sulfide oxidation and aluminum-silicate weathering best summarized the variability in each zone, and that the zones were most different on the basis of sulfide oxidation variables. The geochemical computer code WATEQ4F was used to assess the solubility status (saturation index) of minerals. Saturation indices of sulfide oxidation and aluminum-silicate weathering minerals were different in the two zones. It was demonstrated that the statistical analyses produced similar and complementary results to the geochemical code.

Jan 1, 1992

By W. Drummond

The cooling of smelter gases by air dilution, adiabatic evaporative cooling and indirect heat exchange is discussed with reference to the process, to the subsequent cleaning of the gas. and to the use of the heat extracted from the gas. The method of reducing the effect of acidic sulphide formation on the corrosive properties of the gas and the dust and the development of surface cleaning mechanisms?are discussed. The development of indirect recuperators using air, water or steam cooling, made possible by the control of surface fouling is traced. The application of the modern Waste Heat Boiler to the new sulphide smelting processes is discussed with respect to the natural and forced circulation concepts. Case histories are presented to illustrate mistakes made with respect to designs produced without recourse to sensitivity analysis and without an appreciation of "worst process? conditions".

Jan 1, 1992

By Michael Altepeter

Big River Zinc Corporation, located in Sauget, Illinois, operates a neutral leach residue circuit. The residue produced in the circuit is sold to lead smelters for subsequent recovery of valuable metals. A research program was initiated several years ago to find a means of treating the residue at Big River Zinc to recover the valuable metals. The Ausmelt submerged lance reactor was selected as the best alternative for the first step of the process. Pilot scale tests were conducted at Ausmelt's facilities in Melbourne, Australia. Separations were excellent. 99%+ of the Zn, Pb, Cd, and Ag contained in the residue reported to the oxide fume. 99%+ of the SiO2,, Fe, Mg, and Ca in the residue reported to the slag which passed the EPA TCLP test. Subsequent leaching of the oxide fumes and purification of the leach solutions using conventional procedures produced solUtions suitable for zinc electrowinning and an upgraded lead sulfate cake for sale.

Jan 1, 1992

By S. B. Patton

A computer model, which quantitatively utilizes the relationship between the interactive and dynamic processes of methane drainage, mining, and ventilation, is presented. The model includes simulation of the coalbed methane reservoir for prediction of gas-emission rates under the influence of degasification wells and longwall mining, ventilation network-generation, and ventilation simulation. As mining progresses step-wise through the coalbed-methane reservoir, the ventilation network is created and subsequently simulated, iteratively determining fan requirements to safely reduce methane concentrations. The model can be used to quantitatively study the effectiveness of methane degasification on the ventilation system in a longwall panel.

Jan 1, 1992

By Sarkis G. Ampian

Crystalline silica (quartz, cristobalite, and tridyrnite) is regulated by the Mine Safety and Health Administration (MSHA) and Occupational Safety and Health Administration (OSHA) because of its potential for causing debilitating but nonmalignant lung diseases. In 1987, the International Agency for Research Against Cancer (IARC) conducted a review of the health literature and concluded that crystalline silica was a probable human carcinogen. As a result of this finding, OSHA was required to regulate crystalline silica under its Hazard Communication Standard (HCS). The standard requires that all materials handled by OSHA-regulated facilities be labeled according to the requirements of RCS and that workers receive proper training on the handling of the material if the crystalline silica content equals or exceeds 0.1 weight percent (0.1 %). MSHA currently is considering enacting its own RCS. This will be similar to OSHA's RCS. If the standard is enacted, most mineral producers will have to determine the respirable monitor filter and bulk crystalline silica contents of their ores and products so that workers and/or customers will know whether they are in compliance with the 0.1% HCS and/or the OSHA permissible exposure level (PEL) of 50 µg for an 8-hour workday for respirable crystalline silica as determined from monitor samples. Two major concerns with the RCS are the widespread occurrence of crystalline silica in nature and the suitability of current technology for routinely determining crystalline silica concentrations at the 0.1 % RCS level. Most ores are extracted from silica-bearing deposits and it is a common constituent of rocks and soils. OSHA's RCS will have the greatest impact on the producers of crushed stone, diatomite, dimension stone, gravel, industrial sand, perlite, pumice, pyrophyllite, sand, and talc because these materials frequently are shipped directly from the mill to the customer. MSHA's RCS would affect nearly all mineral producers. Those producers that have crystalline silica present in concentrations near the 0.1 % cutoff point will have the most difficulty with the analysis. Crystalline silica can be quantified at the 0.1 % level by X-ray diffractometry in simple systems containing one, two, and possibly three minerals if (1) none of the accessory minerals has X-ray diffraction reflections that coincide or overlap with those of crystalline silica and (2) the standard has a particle size distribution and crystallinity similar to those of the sample. In some instances, it may not be possible to determine the crystalline silica content of a sample with any degree of certainty using the recommended regulatory protocol. In all cases, it is recommended that a qualified mineralogist identify the minerals in a sample prior to any regulatory analysis. Additionally, the uncertainty as to whether some silica polymorphs should be classified as crystalline or noncrystalline and the suitability of metastable high-temperature standards, such as cristobalite and tridyrnite, for regulatory analysis at ambient temperatures should be addressed further. This overview is written both to highlight these problems and to serve as a guide for analysts, regulators, and industry personnel who are involved in the crystalline silica issue. It also covers some of the difficulties and/or shortcomings in quantifying crystalline silica, such as the ubiquitous mineral quartz, in the workplace.

Jan 1, 1992

By J. R. Hartin

Traditionally, many of the advances in casting technology have been made by expensive and time consuming trial-and-error methodology. Modeling of the complex solidification process promises production of castings which are made "right the first time." Even though several models are available for simulation of conventional casting processes, none of them address this relatively new technology of investment cast titanium aluminides. In this paper, modification and application of a transient, three-dimensional, fully coupled fluid flow and heat transfer solidification modeling computer program to the analysis of centrifugally cast titanium aluminides is discussed. The predictive results of the program are compared to qualities of actual cast parts for validation.

Jan 1, 1992

By Pandey H. D.

The paper describes a fluidised bed ion exchange method for simultaneous removal of phenols and cyanide from the effluent. Use of an eluant enables regeneration of the resin in the continuous operation mode. The breakthrough experiments conducted both on the laboratory scale and on a pilot plant scale have shown that while the level of phenol can be brought down from 462 ppm to about 6 ppm, the free cyanide is almost totally removed. An examination of data indicates that the method can serve the twin objectives of pollution control and phenolic compounds recovery.

Jan 1, 1992

By S. Auger, S. McDonald, K. Ward

"This preliminary paper provides a summary of lab and mill flotation investigations into the copper collector at two Canadian operations. The orebodies illustrated in these studies both contain mainly copper and zinc with uneconomic quantities of lead. Silver is also present as a secondary precious metal.Each mill has advanced to the extended mill trial stage with Uniflot SP129 as the sole copper collector. The preliminary metallurgical results have indicated higher copper circuit zinc and lead rejection is possible as shown in Case Study #2. In Case Study #1, improved zinc circuit metallurgy has been realized during all the Uniflot copper circuit collector trials. A slight increase in silver recovery has also been observed in the extended trials at both operations. INTRODUCTIONThe Canadian base metal industry is presently going through a rationalization period in response to low metal prices and low grade ore bodies. The response from flotation mills has been to reduce costs by incorporating new technologies such as energy efficient large cells, low moisture pressure filters and low steel consumption SAG mills. Other optimization strategies have been incorporated to get better metallurgical performance such as improved process control and monitoring techniques.The newer flotation plants have embraced many of the latest equipment innovations but they continue to incorporate off-the shelf reagents like xanthate and methylisobutylcarbinol (MIBC) . New collector chemistries have been mostly unsuccessful. Our approach incorporates the best of the old and new chemistry into proprietary formulations that match the application. We have found most single chemical formulations cannot meet the demands of the optimized modern flotation plant."

Jan 1, 1992

By T. D. Murphy

In the fall of 1988 it became evident that the accuracy of sulfur forecasts for Monterey Coal's No.1 Mine needed to be improved. In addition, it became necessary to predict if any individual train shipments during a month would exceed a contract sulfur limit. The challenge was to develop a forecasting process that would take into account the variability of the coal in the ground as well as the difference between laboratory and preparation plant sulfur reduction efficiency, and the effects of mining coal with multiple units. This paper describes how geostatistics and simulation techniques were used to meet this challenge.

Jan 1, 1992