Search Documents

By James D. Hervol, Josepph W. III Leonard, Barbara J. Arnold

INTRODUCTION Dry concentration or pneumatic cleaning uses air currents as the separating medium. Pneumatic cleaning in the United States today is limited to three or four operations. In fact, the quantity of bituminous coal cleaned pneumatically has declined from its peak in 1965 of about 25.4 million tons (23.1 Mt) to its current level (1988) of less than 4 million tons (3.64 Mt) annually, as shown in Fig. 7-9 1. In 1940, pneumatic methods accounted for 15% of the bituminous coal and lignite cleaned in the United States as given in Table 7-32. Currently, pneumatic methods account for less than 2%. The largest air plant was built in Pennsylvania about 1968 with 14 units processing 1400 tph (1280 t/h) of 3/, in. X 0 (19 mm X 0) raw feed and two additional units retreating middlings. This same plant is one of only three or four plants still operating air-cleaning devices in the US. A wet plant was added in 1985 to increase the efficiency of cleaning the fines. The air plant is still used as a scalping operation for the coarse material. Five additional operations are either no longer in production or have discontinued the use of air tables within the last year. Wet cleaning methods are now being employed at the facilities that have discontinued air table operation. he advantage of dry cleaning techniques is the low moisture content of the clean coal product. However, to decrease respirable dust, mining operations must use water sprays on modem mining equipment. This water adds to the moisture content of the run-of-mine coal and decreases the effectiveness of dry cleaning processes that rely on low surface moistures in the feed to allow for good separations. Wet cleaning methods are preferred, especially since they also allow for much sharper separations. The advantage of dry cleaning techniques is the low moisture content of the clean coal product. However, to decrease respirable dust, mining operations must use water sprays on modem mining equipment. This water adds to the moisture content of the run-of-mine coal and decreases the effectiveness of dry cleaning processes that rely on low surface moistures in the feed to allow for good separations. Wet cleaning methods are preferred, especially since they also allow for much sharper separations. Despite dry concentration's drawbacks, research has continued into dry concentrating methods, including both electrostatic and magnetic separation techniques. The real application for future dry cleaning processes is probably at the power plant between the pulverizer and the boiler feed where particles are already dry and ground to fine sizes (- 200 mesh [ -0.075 mm]), increasing the effectiveness of the separation and also, possibly, increasing the liberation of clean coal from finely disseminated impurities. From a utility's viewpoint, pneumatic cleaning offers the best delivered Btu cost, based on the premise that a percent of moisture is just as detrimental as a percent of ash. Additionally, several other advantages are inherent in dry concentration techniques. The main advantage is that dry concentration re-

Jan 1, 1991

By La Brooy S R, Fenton K

A low grade copper flotation tailing from Telfer containing 1.2% Cu as chalcocite and cuprite and 5 gt-t Au was leached with ammonia, cyanide and ammonia-cyanide mixtures to extract copper and/or gold. Direct cyanidation extracted both copper and gold but consumed about 30 kgt 1 NaCN. Pre-leaching the tailing with an aerated ammonia solution containing 28 kgt 1NH3 and 17 kgtl(NHa)2S0a at pH 10 readily extracted up to 95% Cu in about 6 hours under optimum conditions. However pH and total ammonia concentration were critical factors. Subsequent cyanidation ex- tracted 80% Au using 6 kgt NNaCN. Ammonia-cyanide mixtures werefound to selectively leach gold over copper depending on the concentration and relative proportion of NH3 and CN. The best composition for leaching up to 80% Au from Teller tailing was 1.6 kgt t NaCN and 1.1 kgf 1 NH3 in the presence of 0.3 kgt t Cue+. Such a mixture left only 50 mgL-1Cu in the final solution after precipitation of some of the initially dissolved copper.

Jan 1, 1991

By William H. Schiffbauer

The U.S. Bureau of Mines has been investigating methods and technology that may improve safety and production when applied to existing mining machines. Toward those goals, the Bureau has developed navigation systems that provide machine positional information while in the production area. This research has been limited in the past because the Bureau had only one type of mining machine to do experiments. Addressing this problem, the Bureau, along with Carnegie Mellon University, has developed a generic vehicle emulator, in the form of a wheeled vehicle with an onboard computer, known as the Locomotion Emulator, that provides a software-selectable vehicle emulation package. Preliminary testing by the Bureau has shown that the emulator can accurately imitate the maneuvers of the software selected vehicle type. Now the Bureau can test their navigation systems on different vehicle types without having to procure each of the vehicles. This report completely describes the emulator as well as all the modes in which it can be operated.

Jan 1, 1991

By C. P. Snyman

Three independent methods of coal classification can be distinguished, namely on the basis of grade, type and rank. The latter two can be determined accurately and unambiguously only by means of microscopical techniques. These three independent variables affect all the coal properties and therefore also the technological behaviour of a particular coal. The influence of the inorganic constituents of coal on the fusibility of the ash and on the length of the slag, and also on fouling and slagging, is discussed. The fractionation of the ash-forming constituents during combustion and gasification of pulverised coal shows that fouling and slagging are not related directly to the fusibility and composition of ash of the coal as a whole. The results of combustion experiments using a drop furnace technique indicate that the ignition temperatures of the light volatiles in the coal, and of the formed char, as well as the burn-out time of the char are more dependent on the rank than on the type or grade of the original coal. High-ash coals, however, apparently ignite at lower temperatures and are more reactive than low-ash coals of similar type and rank. The surface properties of coal, which are important in froth flotation and oil agglomeration, correlate well with the inherent moisture content (and by inference with the heat of wetting and the calorific value) and therefore with the type and rank of the coal. In coal exploration, variations of rank offer the possibility of predicting the presence of an intrusion near the seam, thus contributing to more effective exploration and mine planning.

Jan 1, 1991

By J. Partyka

Respirable dust produced during blasting operations in underground mines exhibits both diffusion and convection properties of the airflow. However, the application of the mathematical model presently used to calculate the change in time in the concentration of blasting pollutants is mostly limited to a single drift and cannot be easily utilized for blasts taking place in stopes. This paper discusses an analytical solution based on considerations that enable us to reliably identify the initial condition. Such an approach may be used for any blasting area regardless of its position, its size, or the ventilation system in use during blasting. In addition, a test procedure using field data is established to determined those parameters not measured directly. As well, equations are derived to find the diffusion coefficient, and the position and size of a dust source from the field data. Mathematical considerations The convection-diffusion problem, for a one-dimensional case, is described by the following partial differential equation (PDE): ct. = Dcxx - Vcx + source - sink(1) where C = the concentration of a pollutant T = time V = the mean air velocity in x-direction D = the diffusion coefficient X = distance away from the pollutant source source = any additional pollutant source specified by an initial value problem sink = decay of a pollutant inside the region specified by the boundary conditions. Respirable dust produced during blasting is best considered as an initial value problem (IVP). To derive a mathematical model, the following assumptions are made: •At time zero (t = 0), the dust source is at point x = 0 of an infinite drift. •The problem is considered a one-dimensional case. •The mean velocity of air and the diffusion coefficient are constant. •There is no source or sink of dust other than specified at point x = 0 and time t = 0. We have to solve the following problem [PDE ct=Dcxx-Vcx-m<x...m;0<t<m(2)] ICc(x,0)=f(x)t=0, the initial condition Where c = dust concentration in mg/m3 V= the average mean velocity in a drift in m/s t= time in s D= the diffusion coefficient in m2 /S x = distance coordinate in m. We observe that in problem (2), we have moved the boundaries to[ -m and +m] in order to have an initial-value problem. We introduce new coordinates, s = t and z =x - Vt. To rewrite the PDE in terms of (z, s), we use the chain rule ct = czzt + csst = -Vcz + cs cx = czzx = cz cxx = (cz)x = czz. We now substitute our computed ct, cx. and cxx into the PDE to get new IVP in terms of z and s :

Jan 1, 1991

By S. G. Britton

Thin seam mining presents unique challenges when management or economic conditions require significant productivity increases. These challenges are increased depending upon the presence of various external factors such as labor unions, Federal and state regulations, and market characteristics. This paper explores the turn-around situation occurring at Tanoma Mining Company (TMC), a medium-sized underground coal mining company in central Pennsylvania, USA. Using a systematic approach of improving management controls and direction, labor relations, and communications, coupled with an intensive upgrade/rebuild/replacement program for equipment and systems used at the mine, TMC has begun reversing its&apos; cashflow position from negative to positive within two years.

Jan 1, 1991

By G. R. Hart

The expected 1990 Clean Air legislation is providing electric utilities with a series of challenges and decisions as the utilities prepare strategies to comply with the resulting regulations. This paper addresses the strategy development of a coal-based utility --the legislation, the process used, the fuel issues, the options available, and the decisions to be made.

Jan 1, 1991

By M. D. Light

An intelligent control system (ICS) is being developed for ferrous iron oxidation by Thiobacillus ferroxitdans. The ICS provides computerized data acquisition and&apos; control of process variables (temperature, Eh, pH, dissolved oxygen arid carbon dioxide concentrations and dilution rate) to maintain the ferrous iron oxidation at the highest possible rate. The ICS uses fuzzy logic for analysis of data inputs and implementation of control strategies. T:his paper provides preliminary information on the development of the ICS and? its operation.

Jan 1, 1991

Jan 1, 1991

By N. A. Abdel-Khalek

The objective of this investigation was to compare the results of counter-current flotation column versus conventional flotation cell for the cleaning of a sulphur ore and its discrete size fractions. The tests were carried out using diesel oil as a collector and alcohol as a frother. Generally, flotation column produced concentrates of higher grade. For example, the grade of a rougher concentrate for a given feed obtained with the column increased by 33% higher than that produced with the flotation cell. Such higher grade could not be obtained using conventional cell even after 3 cleaning stages. Moreover, the column gave superior results for flotation of fine and ultrafine particles.

Jan 1, 1991

By B Mohanty, M Alam, F Gauthuer

A series of eleven full-scale production blasts has been earned out in a limestone quarry to study the effect of delay interval and its precision on overall blasting performance. The quarry employed ANFO and cartridged aluminized emulsion in 75 mm diameter boreholes with 2.6 m burden and 2.9 m spacing on a 6.7 m bench. Both V-cut and echelon designs were studied. The types of detonators tested were regular short period electric detonators with expanding delay intervals, a more precise pyrotechnic-based electric detonator (EXADET) with a fixed (25 ms) delay interval, and the ultra-high precision electronic delay detonator (EDD) with constant (but site-selectable) delay interval. The various techniques employed to assess the blast results are described, and the performance of the three types of detonators compared. The use of both EXADET and EDD lead to improved blast results in echelon design. Of the three delay intervals (25 ms, 38 ms, and 50 ms) studied, the best results were obtained with EDD with a 38 ms delay interval, which translates into a delay of 38 ms/m of effective burden. The results also show the need for modification of current V-cut delay designs to derive full benefits from these high precision detonators.

Jan 1, 1991

By R. H. King

Suboleski and King (1990) analyzed the reasons for the dramatic increase in underground coal mine productivity during the last 10 years. This paper examines whether this increase can be extended. The paper forecasts whether the mix of technological, procedural and other factors that produced the increase will change in the future. The forecast is based on the base case and spreadsheet production model described in the previous paper.

Jan 1, 1991

By Peter Keppler, Charles Jackson

WHY DO AN AUDIT? There is increased enforcement of environmental laws and regulations at State and Federal levels with attendant steep fines and even the possibility of jail sentences. We are all aware of environmental and public health and safety incidences (i.e., Love Canal, Bhopal) which have led to stringent laws and regulations (i.e., CERCLA, RCRA, SARA). In some cases, the courts have specified that a company institute an audit program as a condition of settlement of claims which related to lack of environmental control. The U.S.EPA issued an Environmental Auditing Policy Statement in the November 8, 1985 Federal Register (pp. 46504-46508) which encourages the use of environmental auditing by regulated entities. Elements of what EPA considers to be an effective environmental auditing program are outlined and briefly explained. These factors combine to indicate why there is a growing number of companies which have instituted an audit program. Briefly, the program can and should be used to monitor compliance with environmental regulations and corporate policy, to prevent violations, to improve policies and procedures, to raise the level of environmental awareness, to encourage communication among operations and all management levels about environmental problems, and to measure risks and control costs. AMAX Inc. has had an environmental audit program since the early 1970&apos;s. The AMAX Environmental Affairs Department, working with the Law Department, oversees and coordinates environmental audits and analyzes the findings which an audit reveals. Facilities are audited on a regular schedule; those having the greatest potential for environmental liabilities are audited at least annually; other facilities are audited less frequently. The question of who performs the AMAX audits was settled in favor of the audit team being independent of personnel from the facility being surveyed. Other methods of auditing could be the following: - Independent contractor (Appendix A) - Combination of independent contractor and in-house staff - Self-audit by site personnel The merits and demerits of who should conduct the audit can be analyzed to suit your particular needs. Next you need to decide on the procedure for the audit and the form for reporting and follow up. Environmental publications referenced in Appendix B can be helpful to you at this point. After deciding on the form of auditing, a schedule is prepared and followed to the closest extent possible. This schedule should be published and distributed to the sites so facilities know when they are being audited. This is not designed to be "a game of hide and seek." Various elements of the AMAX Audit Program are as follows: Team selection Pre-visit preparation Site visit Exit interview Report Using the audit Follow-up Team Selection The usual make-up of the team is the audit manager, the environmental specialist who normally provides assistance to the site or has knowledge about the operation, and a legal representative if his or her schedule allows. The legal representative will review the findings of the audit team if a personal visit is not timely or necessary. Size of the team can be expanded, but a minimum of the audit manager and the environmental specialist is best. Two sets of observations are better than one. The environmental specialist can also provide the rapport which is beneficial to creating the appropriate tone so that the site people will be as cooperative as possible. This is not to be an antagonistic exercise.

Jan 1, 1991

By O. Dojcar

The results of a laboratory investigation of rock fragmentation conducted with a model material were partially verified under field conditions. The object of the investigation was to study the qualitative and quantitative relations between the parameters of the primary blast and fragmentation to enable the planning of an economically efficient degree of disintegration with optimum utilisation of the blast energy. The three blast parameters that were considered were burden, specific charge and the ratio of spacing to burden

Jan 1, 1991

By Norman L. Kotraba

In Electric Arc Furnace (EAF) steelmaking, dust emissions are collected in a baghouse to prevent their escape to the Environment. This fine dust, predominantly iron oxide, also contains oxides of various other metals introduced into the EAF from the scrap charge. For example, mixed or galvanized scrap brings with it zinc, lead, and small quantities of cadmium which preferentially accumulate in the collected off-gas dust. Stainless steel scrap brings chromium into the charge, some of which also makes its way into the baghouse dust as hexavalent chromium-containing oxides. Because many of the contained heavy metal oxides are water-leachable, the U. S. Environmental Protection Agency has listed EAF dust as a hazardous waste which, as of August 8, 1988, cannot be 1andfi11ed without first being treated. Moreover, beginning August 8, 1991, all dusts with zinc concentrations of 15% or greater will be required to undergo high temperature thermal treatment to remove the heavy metals prior to any further disposal. This deadline represents several EPA-granted time extensions to the original requirements; extensions which were granted to allow for further development of process technologies.

Jan 1, 1991

By David Kress

Grinding mills, both autogenous and ball can be powered by several basic means. The three methods used today are girth gear drives, gearless drives and trunnion coupled reducers. This paper will focus on the first of these methods -girth gear drives. The girth gear drive has been used on thousands of mills which continue to operate successfully. These drives are noted for their simplicity and low cost. In the past, the horsepower capacity of girth gears has been slow to keep up with the horsepower increase required by the mill builders, particularly since the advent of the SAG mill. Gear manufacturers had capacity for 2000 HP mills in the 1950&apos;s, 5000 HP in the 1960&apos;s and 6500 horsepower in the 1970&apos;s. The 70&apos;s and 80&apos;s brought dual pinion girth gear drives which allowed mill sizes beyond 10,000 horsepower. Gear manufactures who could not keep up with the pace of the horsepower demands and the quality and reliability demanded by the mill builders and users have fallen by the wayside.

Jan 1, 1991

By D. R. Spears

The U.S. Bureau of Mines has developed a Fast Air-injected hydrocyclone-Shallow Tank (FAST) flotation system. Conventional flotation cell kinetics are a compromise between two conflicting requirements, the need for an agitated zone for rapid bubble-particle collision, and a quiescent zone for bubble-pulp separation. The Bureau of Mines has designed a flotation system in which bubble-particle collision and bubble separation are carried out in two discreet unit operations. A bubble slurry was mixed with an ore slurry at a high rate in a modified air-injected hydrocyclone for rapid bubble-particle collision. The mixture was then fed into a unit specially designed for rapid separation of the bubbles from the pulp. A conventional flotation cell required 2.8 min to obtain 90 pet recovery at a 7-pct Cu rougher concentrate grade, whereas the FAST flotation system can obtain 85 pet recovery with a 13-pct Cu rougher concentrate grade in 0.28 min, and 92 pet recovery with a 7-pet Cu grade in 0.56 min. The Bureau&apos;s FAST flotation system is adaptable to a wider variety of flow sheets and could potentially allow for replacement of conventional flotation cells with smaller and faster units.

Jan 1, 1991

By S. Kraemer

Consumption of plastics has been growing in both the U.S. and world markets since the mid-1930s. This growth is due to plastics being used to make new products and as a replacement material for existing products. This paper develops an understanding of the replacement process by looking at the use of plastic, specifically PVC, in the construction pipe industry. History details the growth of the plastics industry and a discussion of the material selection process indicates the advantages and disadvantages of plastic pipe. Analysis shows that the use of plastic, as an alternative material for pipe, is having a significant effect on the cast iron, copper, clay, and steel industries. For the purpose of understanding the replacement process, three example residential systems were examined with a lifecycle cost analysis being performed. PVC was the material of choice in 1988 for all systems. Even though disposal cost was the one area where PVC was not the most cost effective, disposal costs were not sufficient to offset the overall advantage of using PVC on an economic basis. That plastic competes effectively with other materials, in terms of material properties and cost, indicates that further work should be performed to understand the impact plastics have on other material markets.

Jan 1, 1991

By Robert D. Rogers

The demand for phosphate will continue into the future, because phosphate is currently irreplaceable as a plant nutrient and in many chemical applications. Phosphate is not recycled, so the supply must be replenished through a process of mining and purification. Numerous microbial isolates. obtained from the environment were screened find those which demonstrated the greatest promise of solubilizing PO4 from the ore of interest. Screening was accomplished in a step wise manner an agar plate bioassay, shake flask studies, and semi continuous growth conditions. It was found that with the proper conditions of nutrient supply and solution pH; the bacteria and. fungus used in the semicontinuous process were able to solubilize in excess of 80% of an Idaho rock phosphate ore (RP) within nine days. A significant amount of solubilization occurred within the first six days. There was a &apos;reasonable correlation between the occurrence of soluble Ca and PO.4 during the processing of the RP thus providing evidence that the RP was being disintegrated by the organisms. In all cases, HPLC analysis of the solutions in which PO4 had been. extracted from RP showed that organic acids, which have been implicated as the mechanism of solubilization, were present.

Jan 1, 1991

By M. R. Yenchek

The U.S. Bureau of Mines has determined a method for calculating coal mine portable power cable thermal life for a specified temperature loading. This work was the culmination of a multifaceted research project involving (1) accelerated life tests of insulation and jacket materials and (2) steady-state and cyclical loading of cables. Composite Arrhenius curves were derived for common insulation and jacket materials to identify the key cable quality that precipitates thermal failure. Plots of temperature rise versus current for popular cable sizes were then referenced to develop a correspondence between cable life, based upon thermal degradation and current loading. Predictions of cable thermal life were made through integration over variable load cycles and, consequently variable operating temperatures. This procedure may have utility for both the U.S. Mine Safety and Health Administration and mining machine designers in determining the appropriate cable size for new equipment.

Jan 1, 1991