Search Documents

By C. M. McCulloch

The methane content of virgin bituminous coalbed can now be measured accurately in the field with exploration core samples from vertical boreholes. The gas content of the coal per unit weight can be used either to design a mine ventilation system or to determine if degasification of the coalbed will be necessary before mining, and to determine the gas resources in the coalbed. The equipment necessary to conduct the test costs less than $50. The gas con-tent of the coal in place in the ground is determined by summing the gas lost from coring, gas measured during desorption, and the residual gas in the coal. Upon removal from the borehole, the core sample is placed in an airtight container and des orbed for several weeks until the desorption rate is below 0.05 cm3/g for 5 consecutive days. The gas lost from the core while it was being cored and the residual gas are estimated by a new graphical method. The amount of gas remaining depends upon whether the coal is friable or blocky. Friability appears to relate to the depth of the sample below the surface, fixed carbon percentage, Hardgrove grindability index, and proximity to tectonic disturbance. Friable coals emit nearly 96 pct of the total gas during desorption whereas a blocky coal emits only 60 pct of its total gas. Coalbeds that are ill defined as to their blocky or friable nature must be tested in the laboratory for unambiguous analysis.

Jan 1, 1975

By Collins BJ

Basic principles of stack injection are outlined and supported by calculations of thermal, chemical and aerodynamic requirements of an ideal 4000 tpd furnace. Calculated results show that these requirements vary with conversion of FeO, and that best performance may be expected with XFeO = 1.0 for which calculated production is 6919 tpd and coke rate is only 211 kg/thm. Calculations are also presented for a cycled injection. Discussions show that stack injection is a good way of overcoming softening problems and meeting the demand for iron in a fluctuating demand situation when it exceeds the maximum capacity of a furnace.

Jan 1, 1975

By L. L. Anderson

Western bituminous coal can be processed to low sulfur liquid fuels by fast reactions. A process (LEFCO) under development at the University of Utah uses coal and catalyst under hydrogen pressure to convert 60 to 70 percent of the coal matter to fuel liquids and gases. Coals have been processed in small diameter (less than 1/2 inch) tubes and at reaction residence times of less than 10 seconds. Effects of process variables on the yield and quality of products have been studied. General features of the process and the properties and characteristics of the products produced are presented. Special features of the process that distinguish it from other liquefaction processes under development are also discussed.

Jan 1, 1975

By Robert W. Elayer

For the design of a coal mine and process plant, a comprehensive foundation of geologic information is essential. Historically, the development, collation, and use of this information for design have been costly and time consuming. With the application of a digital computer, however, the effort expended can be reduced and maximum effective use of the geologic information realized. The purpose of this paper is to demonstrate the feasibility and convenience of using a computer to Store and manipulate geologic data for use in mine and process plant design.

Jan 1, 1975

By D. R. Kelland

A program has been carried out over the last two years to apply the technology of High Gradient Magnetic Separation (HGMS) to the problem of mineral beneficiation and specifically oxidized taconite iron ores. This program, supported by the RANN division of the National Science Foundation, has consisted of a laboratory program at the Francis Bitter National Magnet Lab- oratory at MIT and a pilot investigation at the Hanna Mining Company Research Laboratory. 1 The laboratory tests were conducted using several batch type high gradient separators and a continuous separator with a rotating matrix which was constructed at the beginning of the program. The high field magnets available at F.B.N.M.L. were used for investigations above 10 kG but most of the test work was performed in the range of this field value. Ore samples were contributed by several iron ore companies and consisted of oxidized taconites having goethite and hematite as their principal components.

Jan 1, 1975

By Gilbert DJ, Lemon NM

A case history of a two year study of low grade ores in the Middleback Range area with the objective of defining possible areas of interest from a combination of geological- petrological-metallurgical criteria. Covering the general geology of the area and ore types; the results of metallurgical testwork and the pattern of evolution of these tests; the petrological explanation of the results of the testwork; the culmination of the work in the selection of areas of best potential for more intensive work. Jaspilites consisting of magnetite, hematite and limonite with quartz and silicate-carbonate-sulphide minerals are hosts to high grade iron mineralisation but also constitute a large low grade iron Reserve.

Jan 1, 1975

By Bradley V. Johnson

The Bureau of Mines constructed a microminer--a scaled-down (5-by 5- by 11-foot) continuous-mining machine of the drum type with a unique triaxially controlled head--for use in a research program to study the effects of continuous-mining-machine parameters on the generation of respirable dust. This report describes field research with the microminer at the Bureau's Experimental Mine at Bruceton, Pa. Experiments were conducted to determine the effects of depth of cut, rotational speed, and sump and shear rates on the generation of respirable dust. The cutting forces were also monitored and compared with depth of cut. There appears to be a reduction in the amount of respirable dust generated when the depth of cut is increased or rotational is speed lowered, Variation of other machine parameters seems to have little effect on dust generation.

Jan 1, 1975

By Gary Beerkircher

The mine hoisting equipment that is selected and installed at a mine is the lifeline of the mine, and therefore the proper selection of equipment will save a lot of time and money during the life of the mine. Various types of mine hoist designs &e available today, and each has their advantages and disadvantages. Double Drum Hoists, Single Drum Hoists, Friction Hoists and various special designs of these are available but should only be used on applications where they are suitable. There have been several new drive systems for mine hoists which have come into the picture in the last ten years, and they in turn must be evaluated along with the existing drive systems for each hoist application. It does not make sense to properly select the hoist mechanicals, and then have a drive system that turns out to be a bottleneck. This paper will attempt to cover the above noted systems - both the hoist selection and hoist drive system that will provide the mine with a reliable and economical hoisting system. I. Mine Hoist Types There are two basic types of mine hoists available in the world today: the drum hoist on which the hoist rope is actually stored during the hoisting cycle, and the friction (Koepe), which merely passes the rope over the wheel during the hoisting process. Following is a general outline of each type of hoist and the hoisting applications that they are suitable for. First let us consider the simple Single Drum Hoist. As a Service or Production Hoist with cage or skip in balance with a counterweight, a Single Drum Hoist can efficiently service one or more levels since the location of the counterweight at anytime is not important. As a Production Hoist with skips in balance the Single Drum Hoist is best used for single level hoisting. All rope adjustments for proper spotting must be done manually for the Single Drum Hoist. This has to be done periodically to compensate for rope stretch. A variation of the Single Drum Hoist is the divided drum hoist. If multi-layer winding is necessary the Single Drum Hoist must have a divider to allow a separate compartment for each rope. If a counterweight is used with a divided drum application the counterweight rope can be wound on a smaller diameter (Figure 2). Consequently, it moves a lesser distance than the main conveyance and rope adjustment problems are reduced.

Jan 1, 1975

By R. L. Bullock

For many years, the combined efforts of machinery manufacturers and mine operators have endeavored to achieve greater productivity from the men involved and the machinery and capital invested, by developing methods to drill blast holes more effectively. Obviously, this means much more than simply developing a drill that will drill a single hole faster. Considerable attention over these years has also been given to methods of carrying and positioning the drilling machine on versatile jumbos, whereby the man's time can he better utilized by the faster drilling machines. Likewise, the art of blasting to utilize the holes that were drilled to achieve the maximum amount of fragmented ore and the methods of moving the broken ore have also progressed. But each phase of the production cycle just described must be made to balance with the other phases of the work. Obviously, major breakthroughs in only one phase don't always generate more "rock in the box" per manshift. Yet, through the persistent effort of the machinery developers and the researchers, the progressive attitudes of mine managers, backed by corporate capital investments, and battle after battle at the operating level, progress is made. Then, if the innovated system is good enough to "stick", in a few years it becomes the system that the newer method must replace, after the same repeated struggle. This is the situation that many mine operators find themselves in today, Looking at their production cycle, which is assumed to be efficient and balanced between drilling, blasting and materials moving capabilities, they tend to guard any visable disruption of the balance of that day's production, and many would prefer to maintain the status quo indefinitely. Yet, if history repeats itself, we can expect any major breakthrough in the cycle to trigger other innovations in the

Jan 1, 1975

By Hugh W. Evans

Many reports and papers have been delivered on projects under construction or already in operation, but we believe there are few that have been written about projects yet to be built specifically dealing with advanced mine and environmental planning. This paper describes such planning for Atlantic Richfield Company's Black Thunder mine. Project planning is a cyclic phenomenom involving four broadly overlapping planning steps (Figure 1). The demands of the public include needs that can be satisfied through planned resource development. Using a base of information that partly exists and must in part be gathered and updated, the preplanned development can be, evaluated. The evaluation process, with built-in environmental constraints leads to an implementation procedure. Implementation results in the development, including the release of the affected area to other public demands that follow.

Jan 1, 1975

By Richard L. Ash

A question that frequently arises during litigation concerned with accidents or alleged damages involving blasting is "were the explosives used according to the best known standards"" The question is not confined to only law suits, however, but also everytime poor blasting results occur. Unfortunately, general guidelines that can be used to define what may be considered as proper practice have not been established by any responsible body upon which to base a reliable Judgment; more often than not decisions are made primarily according to personal opinion.

Jan 1, 1975

By Boehme PW, Gregory OR

The results presented here show quite definitely that in the system investigated the intensity of dispersion is enhanced by switching the flow entry from bottom to sides of the packed trough. Since there is no reason to suppose that this would not be true generally then it is not surprising that the blast furnace dispersion data of Standish and Polthier lie above the data for packed columns with bottom fluid entry. In fact, on the basis of the present results, blast furnace dispersion results can never equal standard packed column behaviour but must always be above these. The result that the intensity of dispersion in the trough model is higher closer to the side ports than away from them is at variance with that of Standish and Polthier blast furnace results. Aside from the obvious structural differences between these two systems, it is thought that the presence of raceways and the tortuous path of the gas flow in the furnace may provide an answer. Clearly this is an important difference in the behaviour of the two systems and further investigations designed to clarify the position would have significant practical value. This would also give an indication of how the furnace D/ud values may be decreased along the whole height - assuming of course that this result gives the best overall performance of the furnace. However, there is to date no knowledge whatsoever about this aspect of blast furnace Technology.

Jan 1, 1975

By Carl E. Williams

A computer program has been developed which will locate the economic limits of an open-pit mine and also designate which ore and waste blocks to remove per period (years or quarters) to maximize the discounted cash flow over the life of the mine. A set of operating constraints was carefully selected so that the following functions are controlled: (1) the removal of overburden by preproduction and production stripping exposes a fixed amount of ore; (2) a constant manpower and equipment usage is insured (except for trucks); (3) the tons of mill ore, concentrate, and stockpiled ore are regulated; (4) the number and extent of shovel moves are minimized; (5) the grindability of the rock is considered as well as the variable haulage cost caused by variable haulage distances and depths; and (6) the size of the shovel working area is regulated. As many as 50 alternate schedules can be produced per computer run. They are arranged in descending order starting with the best solution.

Jan 1, 1975

By James A. Commins

Accurate engineering predictions of energy needs for pollution control equipment used in surface mining operations is critically important to sound management selection of control alternatives. This paper will describe a procedure for evaluating two control alternatives with different energy needs. Three steps are involved: an analysis of the pertinent regulations, a determination of the size distribution of the particles being emitted, a calculation of the energy needs and costs of the candidate control systems as a function of these regulations and emission characteristics. The principal air pollutant to be controlled in surface mining operations is particulates, or dust, some of which is already on the material introduced into the primary crusher and other dust which is generated by the various steps in the subsequent processes. The requirement for control stems both from regulations concerning workers at the operating site, and the community surrounding the operations. In order to speak quantitatively about the need for control we will use regulations that pertain in Pennsylvania although it must be borne in mind that such regulations vary according to juristiction.

Jan 1, 1975

By John B. Gustavson

Gold was first discovered in Alabama in 1830. Before a decade had passed more than 20,000 people were employed in the various gold districts scattered across east-central Alabama. By 1849 most of the presently defined gold districts were known with such towns as Arbacoochee, Chulafinnee, Goldville, Pinetucky, and Idaho being the principal mining camps. The California gold rush of 1849 signaled the end of intensive prospecting in the Alabama Piedmont for the precious metal. Reactivation of many of the old gold districts has been attempted several times since 1849. Significant activity and development took place between 1874 and 1880, 1888 and 1916, and 1929 and 1936. Locally, some of the development met with moderate succes. The last productive gold mine in Alabama ceased production in 1935. The sharp increase in gold prices since 1973 has caused renewed interest in the potential values of gold of the Alabama gold districts. Most of the gold workings have been abandoned for nearly 75 years and are for the most part inaccessible for convential property evaluation. The early gold miners and prospectors in Alabama were more intent upon finding and mining the valuable metal than in recording their activities for future generations. No matter how interesting or historically significant these records might have been the miners kept no records and left behind them few maps as clues to their activities. Inasmuch as most of the old gold districts have been extensively mined and prospected during the past 150 years, there is very little chance of finding large deposits through conventional outcrop prospecting methods. Similarly, the present geologic knowledge of the various districts is insufficient to launch successful exploration programs looking for large blind lode deposits in new locations within the general gold bearing region.

Jan 1, 1975

The Florida phosphate industry, which supplies about three-quarters of the domestic phosphate fertilizer, produces tremendous volumes of phosphatic clay wastes (slimes). These clays retain a high percentage of water for extended periods of time. The clays also pose an environmental hazard because the disposal technique involves aboveground storage behind earthen dams. Although much research has been undertaken by numerous organizations to dewater slime, no completely satisfactory solution has been developed. In June 1972, a cooperative effort by the Federal Bureau of Mines and the Florida phosphate mining industry was initiated to develop a solution for dewatering the Florida phosphatic slimes. This report discusses various aspects of the slimes problem, reviews past research, makes recommendations for future research, and includes a bibliography of references and patents dealing with the subject.

Jan 1, 1975

The new field of environmental investiga tions introduces new problems of ethics, res- ponsibility, conflict of interest and technical procedures. Such investigations involve four elements: developer, consultant, approving authority and the public. It is essential that the consultant provide technical competence, speed and efficiency, impartiality and credibi- lity. Despite allegations to the contrary, it is not in the consultant's own best interest to omit, ignore or obscure significant adverse en vironmental impacts.

Jan 1, 1975

By C. E. Capes

The continuous balling? operation whereby a moist particulate mass is tumbled in a horizontal revolving drum with recirculation of the undersize product can be extremely unstable. Product and recycle rates are subject to wide fluctuations. Although the problem seems to be well-recognized, there is little published information or quantitative data readily available, especially in relation to industrial-scale circuits. Probably the best available published results are in the Russian literature, an illustration of which is given in Figure 1. These data, taken from a study') of some of the factors which influence the stabilization of the pelletizing process, illustrate the wide variations in circulating load and circuit productivity which may be encountered over a period of operation. The problems of balling circuit stability may be traced to random seed or nuclei generation and uncontrolled agglomerate growth. The situation is analogous to that in crystallization processes where (4 considerable attention is given to nucleation control. Traditionally attempts have been made to optimize system and operating variables to stabilize the balling process. A supplemental approach which is taken here is to build on the considerable

Jan 1, 1975

By Raymond J. Kujawa

For general purposes, insulating materials may be any of those mineral substances that provide a barrier between a desired human environmental feature and an unwanted condition. In this sense, radiation shields, electrical insulations, cryogenic insulation, and acoustical barriers would qualify. For this chapter only the thermal and acoustic insulations used for the median range of normal comfort control will be covered. Because of their magnitude and complexity the other fields are left to other chapters. In another sense, this section deals only with the ultra-lightweight aggregates and insulations, rather than the multitude of light-weight structural materials. Definitions and Uses The insulating materials covered in this chapter are the three groups of mineral products that provide thermal or acoustic barriers through the median temperatures encountered in home and industry. The three mineral categories are perlite, vermiculite, and the silicate wools whether they be categorized as glass, mineral, or rock. Perlites are those amorphous aluminum silicates with minor impurities that take the form of a felsitic, glassy lava possessing a pearl-like luster and concentric cracking. In a more commercial sense the term is used to describe either the natural or processed acidic, volcanic glass, containing from 2 to 5% combined water, that may be converted to a frothy mass by heating rapidly to the softening point. Vermiculites are micaceous, hydrated magnesium iron aluminum sheet silicates of varying composition. Commercial vermiculites are any of these sheet silicates that are capable of sufficient expansion on rapid heating to make an acceptable, highly porous product. Mineral wools, rock wools, silicate cottons, glass fiber are generic names for manufactured fibers in which the fiber forming substance may be slag, certain rocks, or glass. The fibers may be made by a blowing or spinning process. The resultant fibers may be felted or matted or gathered in the manner best suited to the use. The three groups may be used competitively to insulate ceilings and walls. The fibers have strong advantages in this area as they may be manufactured in batts that are stable in residential wall construction. The perlites and vermiculites are more suited to insulate cores and cavities of masonry walls and as plaster and concrete aggregates for thermal insulations. Vermiculite is widely used for insulating attic floors. Because of manufacturing techniques and controls, the glass fibers have made great strides as composites in the plastics industry but only a few of these uses classify in the insulation category.

Jan 1, 1975

By Spencer S. Shannon

This chapter is concerned with the uses, geology, exploration, evaluation, preparation for markets, and future of 90thorium and 39yttrium, along with 14 rare-earth elements. The rare-earth metals or lanthanides were divided into three categories by Berzelius. The cerium subgroup is comprised of 57lanthanum, 58cerium, 59praseodymium, 60neodymium, and 62samarium. 61Promethium does not occur naturally. The terbium subgroup includes 63europium, 64gadolinium, and 65terbium. The remaining lanthanides are placed in the yttrium subgroup. Strictly speaking, yttrium is not a rare earth. Because the properties of yttrium resemble those of heavy rare earths, its name has been used as a designating adjective. The yttrium subgroup includes 66dysprosium, 67holmium, 68erbium, 69thulium, 70ytterbium, and 67lutetium. Rare-earth elements, especially those of the same subgroup, tend to occur together rather than in discrete minerals.

Jan 1, 1975