Search Documents

By Phil W. Welch

At first glance, the similarity between the fine grinding of cement clinker and coarse grinding done in other mineral processing industries may seem remote. However, it is interesting to note that the mill discharge fineness of cement clinker is only 70 to 90% passing 100 mesh and quite comparable to other mineral processing grinds. There is however, a greater dependence of the mill on the air separator in the finish grinding of cement clinker than in other mineral processing industries which explains why a technique to guage the balance between a mill and separator first began in the cement industry. (1) More recently an adaptation of this technique has shown its application to the processing of phosphate rock and is the central topic of this paper. First, an explanation of work done with fine grinding cement circuits seems appropriate together with a few general comments regarding cement. When unground or partially ground cement clinker enters a finish grinding mill, it is subjected to mechanical forces of impact and attrition which gradually reduce it to a range of sizes characteristic of finish cement. That is, a range of approximately 1 to 125 microns. The large proportion of superfine particles relative to the coarse and intermediate size particles is typical of portland cement particle size distribution. It accounts for the workability characteristics of plastic concrete and the early strength development of concrete which is so necessary to its successful use as a construction material. For this reason It is quite evident from quality control tests when a shortage of superfines exists.

Jan 1, 1975

By J. M. Stuve

Low-temperature heat capacities and the enthalpy of formation were deter-mined calorimetrically by the Bureau of Mines for CuO?CuS04. The derived standard entropy (S°298.15) was 40.36±0.04 cal/deg-mole, and the enthalpy of formation (?H°f) was -219.l±0.3 kcal/g-mole. A large thermal anomaly was observed in the heat capacity of CuO?CuS04 at 20±0.1 K. Gibbs energy of formation data are tabulated up to 1,200 K. Construction details of a precision low-temperature adiabatic calorimeter capable of determining heat capacities of solids in the temperature range 5 to 320 K are given. A calibrated miniature germanium resistance thermometer was incorporated into the calorimeter to extend the range of accurate measurements below 15 K. High-resistance dc heater windings were used throughout the cryostat to reduce heat conduction of inner connecting wires.

Jan 1, 1975

By Edward D. Thimons

The Bureau of Mines conducted a state-of-the-art study of techniques currently employed to close large openings in underground mines. A large opening was considered to be any opening over 10 feet high and having a cross section of at least 200 square feet. Five salt mines and one limestone mine were visited to observe various methods of sealing large openings. Because of the variations in conditions from mine to mine, no definite conclusions could be drawn as to which is the best method. In mines where waste material is available, stoppings built by piling waste material are efficient and economical. Where waste material is not available properly constructed brattice cloth stoppings are superior to those built from wood, concrete block, or urethane foams.

Jan 1, 1975

By Raymond L. Zahradnik

Marco Polo reported that the Chinese used "black rocks" for fuel, and recent studies indicate that the Chinese may have used coal in small amounts for two or three millennia previously. The use of coal as a major source of energy however, did not begin until about the twelfth century, when the inhabitants of the northeast coast of England discovered that certain black rocks found along the seashore--and thereafter known as "sea soles" would burn. Since this initial discovery, coal has been mined continuously, first in England and shortly thereafter in present Belgium, France, and Western Germany, and finally in all coal-bearing areas of the world, in ever increasing amounts. The production of coal in the United States began about 1820, when 14 tons were reportedly mined. Since that time the production of coal increased steadily until about 1907, after which the rate has fluctuated between the extremes of about 400 and 700 million tons per year. Bituminous coal and lignite production was 590 million tons in 1974. Value of production was $8. 9 billion. Anthracite production was b.3 million tons with a value of $157.5 million.

Jan 1, 1975

By G. W. Cutting

It is well known in both the research field and in commercial flotation processes that the grades and recoveries obtained from flotation plants are heavily influenced by the structure and height of the froths produced in the flotation cells. The development of steady-state mathematical models of flotation processes based upon practical and readily obtained parameters have demanded detailed information about the structure of flotation froths. The important parameters are the distribution of floating values, gangue and water in the froth with respect to froth height, cell pulp density, cell air flow rates and flotation inducing additives. Little work has been conducted in this field although considerable attention has been paid to bubble loading and other factors close to the cell froth/pulp interface. Laboratory batch tests are prefaced for the derivation of the above mentioned parameters for both practical and economic reasons. The standard laboratory flotation tests using a batch cell produces a froth of low height (1 to 3 cms generally) together with a varying cell pulp density as the test progresses due to the addition of top up water and the removal of froth from the cell. This form of test can be considered only as giving information about froth conditions close to the cell froth/pulp interface under conditions of widely varying cell pulp densities. In commercial processes the froth heights are much larger (frequently greater than 10 cms); therefore the laboratory batch test, although useful in many ways, does not directly yield parameters relating the state of the froth flowing over the cell lip to process operating conditions. To investigate flotation conditions, where more realistic froth heights are developed, an equilibrium type of batch cell has been developed at Warren Spring 1 Laboratory . In this a tank with high walls is used to contain the pulp and whole froth and, after a short period of operation, an equilibrium between froth

Jan 1, 1975

By R. H. King

Underground coal mining machinery utilizes portable electric sables, "trailing cables." to obtain power from load centers or distribution boxes. Cables are frequently damaged since mobile equipment, poor lighting, and restricted space are inherent to coal mining operations. Normally, the damage is repaired by splicing--the joining of one or more severed conductors and replacing insulation and jacket. Figure 1 illustrates a typical single conductor splice. Although the repair seems simple, difficulty of the splicing process is exemplified by the many safety hazards and frequent production delays that result from defective splices. Forty-two cable splice related injuries were reported to the U.S. Bureau of Mines in 1972 and 1973. Additionally, 17 splices related fires were reported in the three year period prior to December 1972. Assuming the damaged area is quickly located, an average splice time for a two conductor cable is twenty minutes. Some operators estimate this delay is incurred once per day per operating section. If one ton per minute is averaged throughout the shift, each unit could loose 4800 tons per year from splice delays. An estimated cost for materials and labor to make a splice is $20. The expenditure could result in a $4800 annual cost per section. The estimated expense does not include wages of other personnel waiting for the repair to be completed. Nevertheless, labor and materials cost is minor compared to the income lost from decreased production.

Jan 1, 1975

By J. L. Huiatt

The U.S. Bureau of Mines and Great Salt Lake Minerals and Chemical Corp. developed a froth flotation process for concentrating potassium salts from Great Salt Lake solar evaporites containing about 5 percent K. The crude evaporites, which were predominately halite (NaCl) with smaller amounts of kainite (KCl.MgSO4.2.7H20) and schoenite (K2SO4MgSO4.6H20), were conditioned in a saturated brine solution, thus converting nonfloatable kainite to the floatable mineral schoenite. Schoenite was then selectively floated with a medium-molecular weight fatty acid. Continuous small-scale pilot plant testing indicated that 80 percent of the potassium could be recovered from the crude evaporites in flotation concentrates assaying about 11 percent K.

Jan 1, 1975

By R. D. Williams

Several hydrometallurgical leach processes have been recently proposed for the recovery of copper from copper concentrates. These include the Cymet Process of Cypress Metallurgical Processes Corporation, the Arbiter Process of the Anaconda Company, and the Treadwell Process of Treadwell Engineering company(1). These processes and similar processes for recovery of other minerals, have several phenomenological similarities which make their quantitative description difficult at best. These include (a) the presence of more than one phase, (b) non-uniform mineralization of the feed concentrate, (c) surface and diffusional effects, and (d) a particle size distribution which varies with time. Semi-theoretical, rather than purely empirical, treatment of such processes in their developmental stages will result in a better understanding of the physico-chemical mechanisms in effect. This, in turn, will allow reliable process designs to be made on reasonable time scales for reasonable development costs. Once a production unit is built, such an approach will provide straightforward methods for process control and optimization. A research and development effort to determine criteria and procedures for semi- theoretically characterizing such mineral leach recovery processes has been initiated in a joint venture by the Arizona Bureau of Mines and the College of Mines at the University of Arizona. This group has as its task the mathematical characterization of hydrometallurgical leach recovery processes using semi- theoretical mechanisms for the underlying phenomena. The resulting models are experimentally verified and parameterized on the laboratory scale in such a way that they can be utilized with similarity criteria to provide reliable scaleup to production designs. This discussion will be centered around the elements of such an approach and how they fit together.

Jan 1, 1975

By T. A. Sullivan

The use of sulfur combined with either sand or waste copper tailings was investigated by the Bureau of Mines as a substitute for a good graded aggregate in asphalt paving materials. The research was part of a utilization program to develop meaningful uses for a projected oversupply of sulfur. Many sections of the country lack good aggregate for paving but do have available sources of sands and sulfur. The development of paving mixtures of desert sands or tailings with sulfur and asphalt was accomplished in the laboratory and tested by laying small paving test sections. Three types of material were studied for use with the sulfur and asphalt. They were (1) a concrete sand similar in gradation to river or beach sands, (2) desert blow sand, and (3) waste copper tailings. Desert blow sand and waste copper tailings are much finer than concrete sand. Mix designs were established for the three types of materials, sulfur, and asphalt used in the paving materials. The best mix designs were as follows, in weight-percent: 80.5 concrete sand, 13.5 sulfur, and 6 asphalt; and 77 either blow sand or tailings, 17 sulfur, and 6 asphalt. Small-scale testing showed that these mixtures were suitable paving materials but would require specialized equipment for transporting and laying. The chemical modification of sulfur to obtain properties that would allow placement of these materials with normal asphalt paving equipment was studied. Results indicate that reacting sulfur with dicyclopentadiene before adding it to the paving mixture was effective in modifying the sand-sulfur-asphalt paving so it could be placed and rolled with conventional equipment.

Jan 1, 1975

By R. E. Siemens

A process is being developed by the Bureau of Mines to selectively recover nickel and cobalt from low-grade domestic laterites. In laboratory evaluation of the process, the oxides in the laterite were selectively reduced with carbon monoxide at temperatures from 350° to 600° C. For material containing more than about 5 percent magnesia, pyrite additions or post-reduction heat treatments were necessary to achieve satisfactory nickel and cobalt extraction for this range of reduction temperatures. Multistage leaching of the reduced material at ambient temperature and pressure in the presence of oxygen, ammonium sulfate, and ammonium hydroxide extracted up to about 90 and 85 percent of the contained nickel and cobalt, respectively. The nickel was selectively recovered from the leach solution by solvent extraction and was then stripped from the loaded organic with dilute sulfuric acid to provide a nickel-rich electrolyte. Treatment of the raffinate with hydrogen sulfide resulted in the recovery of cobalt as a sulfide. The only contaminant in solution was magnesium which was removed by ion exchange or precipitation. In this process the energy requirements are relatively low and except for minor operation losses, only coke and oxygen are consumed.

Jan 1, 1975

By Ronald Ludchak

Since coal has been designated as the short-term answer to the threatening world energy crisis, improved surface mining techniques, along with improved extraction and handling equipment, are needed to increase the amounts that can economically be mined by open pit methods. A dwindling supply of low cost oil and gas have dictated a major rethinking of our energy sources and their use. New methods for open pit coal mining have to be found to increase coal production and to meet more stringent reclamation laws. Modern twin-engine elevating scrapers can play a vital role in meeting these needs. They are readily available, with short delivery times, from several experienced manufacturers of earthmoving equipment. Recent developments of the elevator system have extended its working range to include many of the materials commonly encountered in open pit mining. The paper deals with the advantages of using twin-engine elevating scrapers in the performance of various mining tasks. These tasks range from utility work to the major task of using the scrapers as a primary stripping toot and, of even more importance, a stripping- reclamation tool for, with scrapers, the overburden can be moved and redeposited in the same strata sequence or soil horizon as in its natural state. A recap of current applications of the elevating scraper will be presented, along with proposed uses.

Jan 1, 1975

By Sathit Tandanand

This Bureau of Mines report describes the method of obtaining a strength index for rock drillability, particularly for percussion drills. The original Protodyakonov method has been slightly modified, essentially to eliminate uncertainties in the measurement of the volume of fines, and to avoid conjecture in selecting the representative value as the strength coefficient. A theoretical consideration of the relevant parameters in the method was extended from a comminution theory, and hence the meaningful value was obtained experimentally by plotting the ratio of the number of drops and the volume of fines against the number of drops. The minimum ratio of the number of drops to the volume of fines in the plot was selected as the coefficient of rock strength. The modified method of obtaining the strength coefficient preserves the original Protodyakonov test apparatus and the merit of simplicity of the test procedure. The modified coefficient of rock strength shows its usefulness in predicting penetration rates with greater reliability than other mechanical properties. Consequently, the drillability curves were drawn using the modified coefficient of rock strength as the parameter for penetration rate prediction in the field.

Jan 1, 1975

By Clifford J. Lewis

The control of sulfur dioxide and fly ash in the emissions from coal-fired boilers is a significant segment of the national environ- mental protection program. Developing technologies to accomplish this objective presently emphasize aqueous scrubbing techniques. Should circumstances require aqueous scrubbing for fly ash control only, provision must nevertheless be made to counteract the presence of sulfur dioxide which can create an acidic and potentially corrosive environment. Major technologies for sulfur dioxide control by aqueous scrubbing include, l), recovery processes yielding sulfuric acid or elemental sulfur and 2), throw-away processes which produce a sludge consisting essentially of calcium sulfite or varying amounts of calcium sulfate.1/ Recovery processes are more sophisticated and best suited for locations where there are markets for sulfuric acid or sulfur, or where sludge disposal is an overriding consideration. Throw-away processes are generally less sophisticated but have a problem in that gas scrubbing systems may not operate for practical time periods without failures due to corrosion and to plugging by particulates and precipitates. To overcome this difficulty, some throw-away systems employ an aqueous solution of caustic in the gas scrubbing device to assure maximum water solubility of sulfur compounds, followed by the addition of lime to the scrubbing medium in a system external to the scrubber to produce the throw-away sludge and regenerate the caustic for recycle. Such systems are referred to as double alkali systems.2/

Jan 1, 1975

By Paul H. Mutschler

The Bureau of Mines sponsored a study of the impact of changing technology on the demand for metallurgical coal and coke to 1985. Individual technologies were analyzed to determine what effect each had on the demand for and the consequent consumption of metallurgical coal and coke in the steel industry. The domestic steel industry demand for metallurgical coal and coke for the production of hot metal will probably increase through 1985. Formcoke if implemented on a worldwide basis could begin to supplant the U.S. export market for metallurgical coal. The major technologies that have contributed to the decline in demand for metallurgical coke per ton of hot metal are (1) the increased usage coupled with higher iron content of agglomerates, (2) modification of blast furnace practices such as high top pressures and blast temperatures, and (3) increases in the injection of supplemental fuels. The projected demand for metallurgical coal and coke under current technology for 1985 are 109.4 and 76.0 million tons, respectively. With future technology implemented, the demand for metallurgical coal and coke will be 82.0 and 56.9 million tons, respectively. The projected domestic demand for metallurgical coke could further decrease by as much as 15 to 20 million tons by 1985 if formcoking proves technologically and economically feasible.

Jan 1, 1975

By H. H. Fields, Joseph Cervik, G. N. Aul

Coal is a soft and brittle material. Drilling rates in the Pittsburgh coalbed using a drag bit exceed 3 ft/min at 2,500-pound thrust. However, maintaining the bit on a horizontal trajectory or parallel to bedding planes to attain lengths of 1,000 feet is difficult. This Bureau of Mines report presents a drill string configuration that can be guided through the coalbed. The angle of the borehole is measured periodically and by proper combinations of bit thrust and rotational speed (r/min), bit trajectory can be lifted or dropped to keep the bit in the coalbed. An example of a hole drilled to 2,126 feet is presented to show levels of thrust and rotational speed used to lift or drop the bit, the seemingly unexplainable events that occur, and the strategy used during drilling. Thrust levels during drilling range from 600 to 2,500 pounds. Hydraulic motors powered by a 30-hp, 440-volt motor provide ample power for drilling horizontal holes 2,000 feet long.

Jan 1, 1975

By Jack W. Carlson

Considering the magnitude of today's public concern with critical mineral and fuel materials, regarding both their midterm and long term availability, the Nation is fortunate to have in place and operating the coordinated data systems of the Geological Survey and the Bureau of Mines. Under the supervision and policy direction of the Assistant Secretary--Energy and Minerals, these Department of the Interior agencies have long been responsible for important mineral activities in the Federal Government. Aside from their highly respected mineral industry publications such as the monthly Mineral Industry Surveys, annual Commodity Data Summaries and topical Professional Papers and Reports of Investigation, the Bureau of Mines and Geological Survey data bases and expertise have been readily available for use in emergency situations. Policymakers and decisionmakers in government have placed major reliance upon this ready mineral data and analytical capability in World War II, the Korean War, the recent price control era, and the Arab oil embargo.

Jan 1, 1975

By W. P. Diamond, B. M. Bench, C. M. McCulloch, Maurice Deul

As part of the Bureau of Mines methane control program, the Pittsburgh coalbed was studied in Washington and Green Counties, Pa., and in Marion and Monongalia Counties, W. Va., where this coalbed is now being mined at its greatest depth. The coalbed thickness appeared to be structurally controlled; the bed was generally thinner near the axes of anticlines and thicker near the axes of synclines. The overburden isopach shows a similar relationship. Most of the clay veins in coal occur in the synclinal troughs, generally under sandstone roof. Cleat orientations measured in 18 underground mines showed that face cleats are perpendicular to the axial trends of the folds, and the butt cleats are parallel to the axial trends, indicating structural control of the cleat. Measurement and analysis of surface joint orientations provide a method for predicting the cleat orientations of the coalbed, but linears measured from infrared photographs and photoindex sheets helped only to determine regional trends. The results of these investigations provide a geologic framework for rational planning for underground mine development to use the best available technology to cope with methane emissions, coalbed discontinuities, and related ground support problems.

Jan 1, 1975

By Drew A. Meyer

Magnetic metals are the granddaddy of products which may be recovered from municipal waste. Aside from hand-picking of newsprint and corrugated boxes, magnetic metals are usually the first items a resource recovery facility considers extracting from the solid waste stream. Magnetic metals from incinerator residues and from municipally mandated source segregation programs were first used in significant quantities by the Copper Industry. The ability of the Copper Industry to consume metals from the municipal solid waste stream raised everyone's hopes that there would be more markets for municipal scrap when more of it became available. Somehow something has gone wrong. It is widely acclaimed that scrap is an environmentally sound and economical source of iron. It is greatly in demand for Its contained energy. The prices that the steel industry has been willing to pay for the scrap during the past year are all the proof anyone should need that scrap Is desirable and sought after. But the very fact that I'm speaking today on the markets for magnetic metals recovered from municipal waste indicates that something Is wrong. Clearly the problem is not that we do not need the scrap. The problem is we have not produced the kind of scrap that consumers are willing to buy - either through ignorance of what the consumers wanted or through a conviction that ferrous scrap is so obviously a good thing somebody will surely want it no matter what. Dr. Harvey Alter of the National Center for Resource Recovery has said "You can't sell garbage". In a sense that is only partly true. It really should be "You can't sell garbage for very long". The Steel Companies, in an effort to prove that steel is an environmentally desirable packaging medium, have bought some scrap that can only be described as garbage. They are to be commended for doing so. The fault lies not with the Steel Company for taking and paying for "garbage" but with the producer of that poorly prepared scrap. Far every instance where the steel industry has purchased the often undesirable product from resource recovery facility there are several magnetic installations sitting Idle because someone forgot the most essential part of producing the magnetic product - selling it to someone.

Jan 1, 1975

By Herbert S. Richey

Two hundred years ago next April, our forebears embarked upon the difficult path to national independence. They succeeded, and shook off the yoke of foreign domination. In the ensuing two centuries, the country was mobilized several times to protect that political and economic independence from foreign domination. These efforts were also successful. Thus, as we stand here on the threshold of our third century of political independence, we can thank previous generations and congratulate ourselves for establishing and maintaining the world's oldest republic. Now -- once again -- the United States faces the challenge of foreign intervention into our economy. This time the battleground is resource avail- ability. America has been blessed with enormous resources. Whether we speak of minerals or timber or water or "amber waves of grain," this nation has benefitted from a resource base that is the envy of the world. This asset, coupled with a political system that permitted us to develop it, has been the physical backbone of our independence. Without the economic independence that this resource base has given us, the political independence we fought for would have been tenuous, at best.

Jan 1, 1975

By R. A. Guidotti

The Federal Bureau of Mines has studied the reaction of oxides of columbium, vanadium, and tantalum with ammonia in vertical, gas-solids reactors at temperatures ranging from 300° to 1,300° C with the goal of preparing nitride intermediates for subsequent preparation of the metals by a thermal-decomposition step. The best nitride conversions were obtained in nonmetal reactors. With Cb205, V2O3, and V205 , low-temperature maxima in reaction rates occurred at 800°,800°, and 450° C, respectively, during oxynitride formation (in A1203) at 1 atm of pure ammonia. Conversion of the oxynitride, in a second step, to the mononitride was optimum at 1,200° C for columbium and 1,050° C for vanadium. In the case of Ta205, the rate of reaction to form Ta3N5 (in a single step) was highest at 900° C, where the presence of up to 5 percent methane was found to be beneficial; improved results were obtained by conducting the nitriding in a rotary kiln. Optimum space velocities (in the vertical Al203 reactor) ranged from 5,280 hr-1 for Cba205 to 7,950 hr-1 for V203. Oxide particle size had little effect upon reaction rates. Under fully optimized conditions, products containing less than 1 percent oxygen were readily obtained in under 6 hours.

Jan 1, 1975