Search Documents

By Des Bolton

With the introduction of Cast Blasting techniques, field controls of Drilling & Blasting operations became more important. New drills were purchased which were equipped with sophisticated instrumentation and more accurate drilling plans were required. Concurrently a decision had to be made on the replacement of borehole logging equipment owned by the mine. The use of a contractor to log blast boreholes was eventually decided upon, the information gained from this operation is used in the short-term drill and blast planning and may also be used to assist in the coaling operation if density I quality correlations prove acceptable.

Jan 1, 1994

By A. W. Khair

This paper presents a strength formula for the design of coal pillars. The formula is derived from results of laboratory experiments, studying the effects of primary factors influencing the strength of the coal specimens/pillars. Five primary factors, significantly affecting the strength characteristics of the coal specimens/pillars were identified and extensive laboratory investigations were carried out. The five primary factors were namely 1) coefficient of friction between loading platens and coal specimens, 2) elastic properties of the loading platens, 3) coal specimen geometry, 4) coal specimen size, and 5) rate of loading. Four to nine levels of variation for each primary factor on the strength of coal were studied. An empirical formula, implementing the variation of the primary factors affecting the strength of coal specimens/pillars, has been developed. A comparative analysis of the results provided by this and some well known formulae is also presented.

Jan 1, 1994

By Compiled by Staff

"INTRODUCTIONThe U.S. Bureau of Mines (USBM) was established in the public interest to conclude inquiries and scientific and technologic investigations on mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increaseee efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the U.S. Bureau of Mines to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, USBM reports the findings of its research and investigations in its own series of publications and also in articles that: appear in scientific, technical, and trade journals; in "" proceedings of conventions and seminars; in' reference books; and in other non-USBM publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make this kind of list both necessary and valuable.This edition describes reports and articles published during calendar years 1992 and 1993. It supplements the 50-year list of Bureau publications from July 1, 1910, to January 1, 196O 2; and these 5- year lists of publications and articles: from January 1, 1965, to December 31, 1969 4, from January 1, 1970,to December 31, 19745 , from January 1, 1975, to December 31, 1979 6 , from January 1, 1980, to December 31, 1984 7 , and from January 1, 1985, to December 31, 1989 8."

Jan 1, 1994

By Frederick T. Wallenberger

"Laser assisted chemical vapor deposition (LCVD) is a new containerless fiber process whereby growth of small diameter fibers or microstructures (microsprings, microsolenoids) occurs directly from the vapor phase. The laser beam has a focal point adjusted to coincide with the tip of the growing fiber inside the reaction chamber. Since the growing fiber is not in contact with reactor walls or foreign materials, it is chemically pure, and suitable for optical uses and uses requiring high structural uniformity. Continuous fibers and multifilament yams are possible. The use -of high reaction chamber pressures (1-10 bar) and a small wavelength Nd-YAG laser made it possible to fabricate small diameter fibers at growth rates >1 mm/s. This paper describes the synthesis of single crystal, polycrystalline and amorphous fibers by LCVD, and provides a comprehensive analysis of phase transformations occurring during their fabrication.IntroductionLaser assisted chemical vapor deposition (LCVD) is a new containerless fiber process [1-10] whereby growth of small diameter fibers or microstructures occurs directly from the vapor phase. The laser beam has a focal point adjusted to coincide with the tip of the growing fiber in the reaction chamber (Figure 1). The diameter of the growing fiber corresponds to that of the laser focus. Depending primarily on the laser energy (Le., the temperature at the growing fiber tip), it is possible to obtain single crystal, poly crystalline or amorphous fibers by this method.Since the growing fiber is not in contact with reactor walls or foreign materials, it is chemically pure, and suitable for optical uses and uses requiring high structural uniformity. Laser assisted CVD is a potentially continuous process; continuous fibers and multifilament yams are possible."

Jan 1, 1994

By K. Yarnaguchi

In the Mitsubishi Continuous Copper Converting Furnace, calcium femte slag is used. Due to its extremely high basicity, the improvement of corrosion resistance of the refractory lining is in need. In order to clarify the corrosion mechanism and to search for a new corrosion resistant material, first, the surface snuctures of bricks corroded in molten slags were observed by EPMA. Second, the dissolution behaviors of sintered MgO-based pellets containing various oxide additives were examined. It was found that the formation and the dissolution of magnesiofemte at the surface of the bricks play an important role in their corrosion and an addition of NiO, Mn02, or Ti02 to MgO is effective in stabilizing the magnesio-femte and improving the corrosion resistance of MgO.

Jan 1, 1994

By G. T. Adel

The flotation behavior of a -28 mesh Pittsburgh No. 8 coal sample is investigated through the use of Scanning Electron Microscopy in conjunction with Image Analysis. Release analysis is used to generate the flotation products, which are then characterized to provide the particulate composition in terms of pyrite, mineral matter and carbonaceous material. The results of this investigation indicate that the material recovered in the first stage of release analysis tends to be well-liberated carbonaceous material. This is followed by an increase in the recovery of middlings and fines in the later stages of the process. Any free carbonaceous material remaining in the tailings from the release analysis test tends to be associated with the very fine sizes (-400 mesh). Pyrite recovery is attributed to the hydrophobicity provided by small inclusions of carbonaceous material, since the amount of truly liberated pyrite particles (i.e., 100% pyrite) present in the sample is found to be negligible.

Jan 1, 1994

By R. Hagemeyer

In North America, the paper industry is by far the largest consumer of coating and filler mineral pigments. Present use is at an annual rate of 5.5 million metric tons with a value of $660 million. Current estimates are 65 percent is used in coating and 35 percent in filler applications. During the past decade, the switch to alkaline papermaking has provided the opportunity to substantially increase filler levels while maintaining paper strength. As a result filler consumption has been growing at a late in excess of 15 percent yearly. Unfortunately, within a few years, mandated recycling could slow or even reverse this trend. The critical issue is finding an economically viable method for recycling the mineral pigment and/or minimizing the disposal problem

Jan 1, 1994

By W. J. Mcgaughey, R. G. McCreary, S. C. Maxwell, R. P. Young

"Seismic tomography is a process for obtaining images or maps of seismic velocity or other seismic properties of a rock mass. Seismic velocity images reveal variation in elastic moduli which, in tum, are related to several properties required in the geological or geomechanical assessment of a rock mass. Seismic velocity is sensitive to lithology, discontinuities, and in situ stress. Spatial or temporal variation of these properties may be indirectly assessed. Tomographic measurements are sensitive to volumes of ground, rather than determinations at points, or along lines or surfaces, as in conventional geological or geomechanical measurements or mappings.Tomography surveys are complementary to conventional measurements as they have the capability to interrogate a substantially larger volume of ground. They are thus useful in discerning trends or patterns in regions between or surrounding conventional ""point"" measurements of lithology, rock quality, stress, or other parameters of interest. Seismic velocity images give broad indications of trends in velocity; their spatial resolution of ground properties is typically on the order of five to ten per cent of the nominal survey dimension.Research in seismic tomography has been carried out for several years, and the capabilities and limitations of the technique in mining environments are beginning to be understood. This report reviews the present capabilities of seismic tomography surveys in mining, emphasizing rock mechanics applications. Six case studies are used as examples to demonstrate the capabilities of the method in assessing lithological variation, density and orientation of discontinuities, and the effects of stress."

Jan 1, 1994

In his keynote address at the 18th International Minerals Processing Conference (IMPC), R.P. King, director of the University of Utah Comminution Center, said "it will be the application of very fundamental physical principles that is likely to bring major advances in comminution technology (IMPC, pp. 39-45)." It is evident from the literature published in 1993 that many of these fundamental studies, particularly as they relate to single-particle fracture mechanics and mineral liberation, are starting to bear fruit. The beginnings of fundamental mathematical models for design, scale-up and control of comminution systems are now taking shape. Modeling/fundamentals Population balance models (PBM) have been used to describe grinding systems for 20 to 30 years. However, Williams and Meloy (IMPC, pp. 73-79) pointed out some of the inherent problems with this modeling approach and that there is no unique solution for the unconstrained PBM for grinding. Many of the current constraints used to back-fit selection and breakage functions were also shown to have problems. The need for a more fundamental means of determining these parameters was indicated.

Jan 1, 1994

Mineralogical and metallurgical scoping testwork were carried out to investigate the production of separate, marketable gold and platinum concentrates. The study utilized a flotation concentrate assaying approximately 5 wt% gold and 5 grams per tonne platinum. The gold-platinum mineralization was recovered from a placer deposit. Optical microscopy and scanning electron microscopy with energy dispersive x-ray analysis identified gold as zoned Au- Ag and Au-Ag-Cu alloys. Platinum primarily occurred as weakly zoned, variably magnetic Pt- Pd-Fe alloys. A combination of gravity and magnetic separations resulted in a gold concentrate grading 86.9 wt% Au (and 9.lwt% Ag) and a separate platinum concentrate grading 400 g/t Pt with recoveries of 94.5% and 96.7%, respectively. Magnetohydrostatic separation (MHS) using the Magstream 200 Separator indicated promising results.

Jan 1, 1994

By Jamal Hematian

Understanding the behaviour of rocks in a high horizontal stress field, such as that in Australia, is critical when analysing the stability of underground structures. This paper addresses the significance of the post-failure behaviour of rocks on the stability of underground structures which are under the influence of a high horizontal stress field. The research work was conducted through a combination of numerical modelling, laboratory testing and field investigation. A number of 2-D FE model of roadways were constructed based on the data obtained from laboratory testing and field investigations. The models were then analysed using three different solution techniques; simple linear-elastic, non-linear elastic-plastic and elastic-plastic with consideration of post-failure behaviour (softening model). Results indicated that the post-failure behaviour of rocks significantly influence the stress and displacement patterns around the roadway. The stress and displacement patterns as well as the extent of the yield zone around the roadway predicted by the softening model were in good agreement with that from the field study. Based on the results of the study, an appropriate support system has been suggested to govern the stability of roadways.

Jan 1, 1994

By D. Bois, F. P. Hassani, M. Hossein

"A growing environmental awareness hos prompted the mineral industry to seek innovations in waste management and technology. It is estimated that over 500 million metric tonnes of solid waste each year are rejected by the Canadian mineral industry. This waste hos to be disposed of in the most environmentally and economically acceptable manner.An extensive study has been conducted to estimate the cost of implementing total tailings fill from a waste disposal point-of-view as an alternative to large-scale surface disposal of tailings. The cost of waste disposal at the surface (tailings pond), and underground (total tailings fill) for three Canadian mines which have taken part in Quebec Mine Survey conducted in 1992 are analyzed. Surface disposal is the most economical and common method of mine waste disposal in Canada. Total tailings backfill as a method of waste disposal is technically feasible but cannot be regarded as more economic than surface disposal in all . It is important to remember that while surface disposal costs are rising, due to tighter legislation and more environmental pressure on governments; the costs of preparing and placing total tailings backfill is still falling as the technology improves."

Jan 1, 1994

By Ulrich Von Stackelber

Deep sea mining of manganese nodules actually will have an environmental impact to the seafloor and to the water column. However, we are far from being able to predict the possible consequences. Therefore, in 1992 environmental studies were conducted with the R/V Sonne in a manganese nodule field of the Peru Basin. The bathymetry of the seafloor was mapped using the hydrosweep system and the distribution and type of sediments were investigated by the parasound system and by collecting surface samples and sediment cores. Deep towing of a side-scan sonar system revealed a Mn encrustation of sediments and a nodule coverage of variable density. Along the tracks of a photo sledge a great variability of bottom fauna and of bioturbation was observed. Bottom-mechanical investigations of surface-near sediments were completed on board. Additionally water samples were collected near the sea floor to determine character and amount of dissolved and suspended particles. Manganese nodules and crusts were collected at 80 locations. In many aspects the nodules differ from those of the Clarion-Clipperton Zone: Big cauliflower-shaped nodules with growth rates up to 160 mm/ Ma may reach a maximum size of 24 cm in diameter, maximum abundance may be 44 kg/m2, the mean size of buried nodules is greater than that of surface nodules. The reason for that difference is due to the relatively high bioproductivity in surface waters and to a Mn redox boundary in the sediment column 10 cm below the seafloor. Histograms of nodules showing the distribution of size and growth type clearly indicate that the growth history is different for basins, slopes and tops of seamounts and ridges. Nodules with diameters >7 cm show mainly diagenetic and to a minor degree hydrogenetic growth. Smaller nodules of the same assemblage are composed mainly of hydrogenetically grown Mn oxide. The optimum diagenetic growth occurs within the sediment immediately above the Mn redox boundary, a level which is not reached by the small nodules.

Jan 1, 1994

By K. Kim, T. M. Yegulalp

A new explanation of the scale dependency of rock strength is presented based on the theory of extremes. A brief review of past work on specimen size and strength relationship is followed by an introduction to the fundamentals of the underlying theory of extremes and its relationship to the scale effect. It is shown that the weakest link theory is directly related to extremal statistics and that parameters of strength distributions of rock can be derived as a function of the specimen size. Three sets of Brazilian test data are used to demonstrate the use of this approach.

Jan 1, 1994

By James B. Pfeiffer

TETRA Technologies, Inc., has applied its HDS? metals precipitation system to control a mine drainage problem. The effluent from the mine contains primarily zinc, manganese and iron, plus varying small amounts of cadmium, copper and lead. The flow from the mine averages 350 gpm, and varies considerably depending on season and weather conditions. The plant was designed to treat 1000 gpm of the water and generate a dense sludge suitable for recycling. The HDS? system contains a number of reactors, followed by post filtration and meets stringent metals discharge criteria as specified by New Source Performance Standards.

Jan 1, 1994

A failure of the Pit IA highwall in July 1989 led Newcrest Mining Ltd's Telfer Gold Mine to commence underground operations approximately 12 months ahead of schedule. The failure presented four major challenges to management: 1. how to maximise the recovery of the Middle Vale Reef (MVR) in the open pit: 2. how to minimise the risk to personnel involved in the extraction of the remaining open pit ore; 3. how to avoid disruption to ore supply: and 4. how to maintain a permanent and safe means of accessing the underground operations from the base of the pit. The risks associated with meeting these challenges were minimised through the installation of a complex network of real time slope monitoring equipment. These monitors were connected to an alarm system which was combined with detailed operational procedures to be carried out in the event of a highwall alarm being triggered. The accuracy with which the risk of failure has been managed was demonstrated recently when the onset of a second failure was initially identified some 13 months prior to its ultimate collapse in October 1992. The location, timing and size of the failure was able to be predicted allowing appropriate precautionary measures to be taken to ensure safety of access to the underground portal and pumping equipment in the base of the pit. This paper reviews the sequence of events leading to both the July 1989 and October 1992 failures of the Pit 1A highwall and the monitoring equipment and procedures used to identify, quantify and manage the risk to personnel operating in the base of the pit.

Jan 1, 1994

By A. F. Alsobrook

Specialty silica materials, as defined in this chapter, are rocks that consist predominantly of silica (SiO2) and are produced as chunks, round pebbles, and sawed or trimmed blocks and other shapes for nonconstruction applications. The rock types include quartzite, sandstone, novaculite, flint, chert, and vein quartz. Other terms used commercially include jasper, silex, lascas, and rock crystal. In its publication, Minerals Yearbook, the US Bureau of Mines (USBM) reports the production and consumption of some specialty silica materials under several headings. Quartzite, sandstone, and novaculite used in abrasive applications are addressed by the USBM under Abrasive Materials. Lascas, a type of vein quartz used in growing synthetic quartz crystals and in fusing applications, is discussed under Quartz Crystal. Silica gravel used in manufacturing silicon metal and ferrosilicon, as metallurgical fluxstone, and as a filtration medium is covered under Industrial Sand and Gravel. Information on

Jan 1, 1994

The Centenary Distinguished Lecture was held on Thursday, 24th March, 1994 at the Convention Centre of the Sandton Sun, Johannesburg at 20:00. Herewith the proceedings that followed. P.R. Janisch: The South African Institute of Mining and Metalurgy began life one hundred years ago tonight, and eight years (almost to the day) after the 1886 discovery of gold, which has impacted so profoundly on the course of events in our country since then. The Early Years That discovery was a mater of fortune, but not in the sense of the conventional prospector's lucky strike. Canny explorers, such as the Strubens, had been around for some years and, if George Harrison had not stumbled over the Main Reef when he did, someone else would surely have done so within months. The element of luck was that the gold-bearing rocks of the Witwatersrand actually lay exposed to sight. We now know that they are something of the order of 2,5 billion years old. Rocks of that age are usually covered by younger formations. In fact, the bulk of the Witwatersrand Basin is covered by lava, dolomite, and Karoo measures. What, one wonders, would our history have been had the Karoo, which stops at the Vaal, extended no more than 60 kilometres further north. Dr H. Scot-Russell A piece of advice attributed to Paul Kruger, the who was President of the South African Republic one hundred years ago, was the following: 'Seek from the past that which is good, and build on it for the future'. It is advice that can be applied universally and, whether deliberately or not, it must have motivated my predecessors when this Institute celebrated its 40th, 50th, and 75th birthdays. Those milestones were each marked by retrospectives, as Peter Janisch has so ably presented tonight on our hundredth anniversary. The parallels do not end there. We find ourselves in times no less daunting than those our predecessors. Next month will see the birth of a new kind of South Africa; so did May 1902, May 1919, and May 1948.

Jan 1, 1994

By Howard K. Worner

Several features of smelting and refining operations make them appropriate technology to adapt to the processing of "wastes" not only from the minerals Industry itself, but for wastes in general. These features include significantly higher temperatures than are achieved in conventional Incinerators and also good thermal stability derived from the mass of molten metal and slag in the furnace. This paper expands on Information contributed to the Mervyn Willis Symposium in July 1992 and includes knowledge generated in the last two years of waste processing R&D in a sealed 100kg capacity DC arc furnace specially constructed for the "Environment" process being developed in Wollongong. As one product of-the process is a foundry-type iron, the feed always contained ferruginous dusts or heavily contaminated scrap. For the dusts, sewage sludge has been used as a binder and also as a proportion of the fuel-reductant. To achieve the necessary bath carburisation, It is beneficial to add other lower reactivity carbons such as "kish' graphite, carbon from electrode butts, dusts from coke ovens, carbon from aluminium pot line residues, dry cell batteries etc. Metallurgical factors involved In process control, Including metal and slag, compositions, are discussed.

Jan 1, 1994

By Timothy J. Rohrbacher

This report presents a U.S. Bureau of Mines study that incorporates coal mining factors, coal recovery factors, and economic factors into the definition of an economically recoverable coal resource. The relationship between these factors to the Energy Information Administration's estimate of U.S. coal resources-the "Demonstrated Reserve Base"-is discussed. The Boltsfork 7 1/2-minute quadrangle in eastern Kentucky was selected as the study area. Results indicate that of the original 280.2 M tons of resource in the quadrangle, only 99.8 M tons (35.6%) is recoverable at a mining cost of $25 per ton or less.

Jan 1, 1994