Search Documents

By A. F. Baker

Tests were conducted in commercial foundries to determine the suitability of calcined anthracite as a cupola fuel. The calcined anthracite performed satisfactorily at two of the three foundries where iron-melting tests were conducted. Performance at the third installation was unsatisfactory because metal temperatures deviated widely and, in general, were lower than is desirable for the type of castings being made.

Jan 1, 1963

By Arcy, D&apos Banister

Drilling practices at the Silver Summit mine in Shoshone County, Idaho, and the steps taken to increase drilling efficiency are described for the 1952 to 1958 operating period. Mining and development methods are outlined, and drilling equipment and practice are discussed. Cost and performance data include drilling time, bit duty, steel failure, drill repair, and compressed-air consumption. Steps taken to increase drilling efficiency and decrease costs are described, including modifications of bit design, new procedures for drill-rod fabrication and new processes for completing certain drill-machine repairs.

Jan 1, 1963

By W. R. Hardwick

This paper describing the mining methods of the Inspiration Consolidated Copper Co. is one of a series being prepared by the Bureau of Mines on mining methods and costs in various mining districts of the United States. The story of mining at Inspiration is of particular interest because, after 127,812,000 tons of low-grade copper ore were successfully mined, the mining method was changed from block caving to open-pit. As the open pit became deeper, many features of the former block-caving operation that were exposed elucidated concepts of the mechanics of caving that previously had been assumed but not observed. The conversion to open-pit mining was accomplished by unique combinations of equipment and the introduction of ingenious engineering and operating practices that have extended the expected life of the mine for many years.

Jan 1, 1963

By F. D. Everett

This report, based on information made available by four uranium-producing companies, describes the geology, exploration, open-pit development and mining, and shaft sinking in the Gas Hills uranium district of Wyoming. Open-pit stripping features motor-scrapers push-loaded by crawler or rubber-tired tractors. The ground generally can be ripped, and little blasting is necessary. Detailed data are given on grouting for ground stabilization in sinking a small-diameter shaft in the relatively unconsolidated sandstone and siltstone, Cost and performance data are presented as made available by the companies.

Jan 1, 1963

By A. J. Paul Laprairie

The process for which it is to be used is too often the only consideration in the design of a vessel. A de-sign allowing for practical manufacture and erection, as well as for proper maintenance, can often give over-all economies. Most platework in-stalled today is of welded construction. Therefore, metallurgical control is important in its manufacture. Also, because many concentrating and re-fining processes tend to be corrosive, the subject of protective coatings as a part of the manufacturing process is extremely important. The plant de-signer should know how to evaluate and specify controls for the metallurgy and for the coatings. Mining operations are becoming more sophisticated in the field of mechanical engineering. More and more emphasis is being given to preventive maintenance. The first step in any maintenance program, however, is good inspection service. This paper will suggest methods for the inspection of platework, and outline methods for repair and replacement.

Jan 1, 1963

By R. M. Gooding

This paper presents a short history of the production of mineral-energy fuels and energy from waterpower in the United States, with brief discussions of the utilization of each of the fuels and hydropower, and a look at fuels competition and interchangeability. Basic data, in figures and tables, are brought together in this publication for the production of coal in the United States from 1800 to 1960, for crude petroleum, natural gas liquids, and natural gas from 1859 to 1960, and for hydropower since 1900. Production for each segment of the fuels complex in the principal producing States from 1946 to 1960 is shown. Data are not included for consumption as such or for imports and exports.

Jan 1, 1963

By E. Maré

Some of the members will probably ask themselves what close relationship exists between hydro-metallurgy and a wet scrubber, but we are sure that as soon as deeper thought is given to the matter it will be realised how vital scrubbing, operations are in metallurgical plants. In ordinary metallurgical installations or pyro-metallurgical processes ore concentrates are first of all shifted from place to place and dust is created. In other cases the ores or concentrates are crushed or dried or roasted, and in each one of these operations dust and fumes, are created. All suspended particles and fumes originating from the abovementioned conditions not only, in many instances, provide health hazards which disrupt production and endanger the personnel in the plant, but also are the source of economic losses through extra maintenance and wear to moving machinery due to abrasion and corrosion. Further losses are incurred by the waste of fine, very often valuable, components. The Party who once said that in several metallurgical plants the bulk of the profits was discharged into the atmosphere by the stack wasn't stretching the truth. There is a place in Africa where a gold producing concern used to lose over 5 oz. of fine gold per day out of a total production of 3000 oz. per month. In another instance, copper concentrate going as high as 80% Cu was discharged into the atmosphere at the rate of 4 tons per day. Realising the value of removing and collecting solids and fumes created in metallurgical plants, a thorough study was made of the available plant and equipment offered on the market. Some units were found very efficient, but very expensive; some others also very efficient but with temperature and maintenance limitations. Some others were also efficient but prohibitive from the point of running costs.

Jan 1, 1963

By W G. Brese

The attention of the world is being focused on the spectacular rise of elemental sulphur production in Alberta. In the short space of a decade, production has increased from less than 10,000 long tons, in 1952, to al-most 1,000,000 long tons in 1962. Moreover, 1963 sulphur production is expected to rise by 50 per cent to approximately 1,500,000 long tons, and further increases are forecast for ensuing years. The reason for this dramatic in-crease in elemental sulphur production, particularly in the last year or two, is that Alberta elemental sulphur is recovered in association with the production of sour natural gas. When very large volumes of natural gas began moving to U.S. markets in the latter part of 1961, the resultant increase in sour gas production led to a marked increase in the production of sulphur. Consequently, Canada, mainly on the strength of sulphur produced in Alberta, will soon become the second largest producer of sulphur in the Free World

Jan 1, 1963

By John Plecash

This paper comprises a general outline of all of the developments, including the history, geology, mining, milling, power and transportation installations, at the gold mining operation of La Luz Mines Limited and the copper mining operation of its wholly-owned subsidiary, Rosita Mines Limited, both located in north-central Nicaragua. The low-grade, gold-bearing ore-bodies of La Luz Mines, contained in highly fractured and folded Lower Cretaceous sedimentary rocks, were from 1909 to 1928, mined and treated by primitive methods by the La Luz and Los Angeles Mining Company. The abandoned property was acquired by La Luz Mines Limited in 1936, and was equipped with modern machinery and put into production in 1939. Between 1939 and 1948, the daily rate of production was in-creased from 300 tons per day to 2,-000 ton per day. The ore reserves available for open-pit mining were depleted in 1954. Since then, the entire production has come from under-ground operations.

Jan 1, 1963

The primary steel industry of the Prairie Provinces consists essentially of three companies whose total annual melting capacity, as of January 1, 1963, was 333,000 net tons. These companies have steel rolling facilities. In addition, there are five other companies producing steel castings by melting scrap in electric furnaces which, with the plants having rolling facilities, gives a total annual furnace melting capacity of 380,000 tons. Since 1954, the annual production of steel ingots and castings has ranged from a low of 66,588 tons, in 1954, to a high of 211,138 tons in 1961. The present facilities on the Prairies for making steel ingots from scrap, and rolling them to produce light merchant mill products, appear to be sufficient for many years ahead. Steel scrap, as electric furnace feed to make steel ingots for the present line of products, will probably continue to be available at reasonable prices either on the Prairies or from the north-central United States. It is recognized, however, that residual elements in scrap may be-come of greater significance and necessitate more rigid control of scrap quality.

Jan 1, 1963

By Arcy, D&apos Banister

Drilling practices at the Silver Summit mine in Shoshone County, Idaho, and the steps taken to increase drilling efficiency are described for the 1952 to 1958 operating period. Mining and development methods are outlined, and drilling equipment and practice are discussed, Cost and performance data include drilling time, bit duty, steel failure, drill repair, and compressed-air consumption. Steps taken to increase drilling efficiency and decrease costs are described, including modifications of bit design, new procedures for drill-rod fabrication and new processes for completing certain drill-machine repairs.

Jan 1, 1963

By H. L. Riley

This report describes the methods and equipment used by the Watauga Stone Co. to drill and blast limestone in a two-level quarry, and to crush, screen, blend, and load this stone. Power requirements per ton of stone produced are reported. The personnel requirements for individual phases of the operation are tabulated in man-hours per ton of stone produced.

Jan 1, 1963

By Ernst P. Hall

As a scientist and an engineer whose responsibilities include the consideration of air pollution and its control, I am frequently called upon to answer variations of two basic questions, These questions may I be set forth as: (1) How much air pollution does the coal industry cause? (2) How serious is the air pollution problem to the coal industry? At first these questions may seem elementary and almost trite, but serious consideration of them will show that they are technologically involved and I further complicated by the subjective base to which they must be evaluated.

Jan 1, 1963

By H. L. Riley

This report describes the methods and equipment used by the Watauga Stone Co. to drill und blast limestone in a two-level quarry, and to crush, screen, blend, and load this stone. Power requirements per ton of stone produced are reported. The personnel requirements for individual phases of the operation are tabulated in man-hours per ton of stone produced.

Jan 1, 1963

By R. M. Gooding

This paper presents a short history of the production of mineral-energy fuels and energy from waterpower in the United States, with brief discussions of the utilization of each of the fuels and hydropower, and a look at fuels competition and interchangeability. Basic data, in figures and tables, are brought together in this publication for the production of coal in the United States from 1800 to 1960, for crude petroleum, natural gas liquids, and natural gas from 1859 to 1960, and for hydropower since 1900. Production for each segment of the fuels complex in the principal producing States from 1946 to 1960 is shown. Data are not included for consumption as such or for imports and exports.

Jan 1, 1963

By R. J. Morlock

Prior to 1912, coal research for Republic Steel, Corporation was limited to a periodic box test conducted in a commercial coke oven. Then in 1912, a Koppers movable-wall test oven was -built to research wall pressures for selected blends and to conduct other varied research work. In the 1950's economic pressures caused a reassessment of position resulting in the establishment of a Coal and Coal Chemical research group in 1956. In 1958 this group, along with other groups of research endeavor were incorporated into the new Republic Steel Corporation Research Center at Independence¬ Ohio. Currently this section is divided into four groups. 1) Coal Preparation, 2) Coal-Chemicals, 3) Coal Characterization, and 4) Coal Carbonization. The objective of each group is described, and a brief listing of the work done under the first three groups is indicated. A more detailed description of the studies by the Coal Carbonization group of the coking characteristics of Republic Steel Corporation's coals as blended among themselves or in conjunction with selected purchased coals follows. The wall pressure, contraction, and stability index criteria are specified, and the method of assessing these criteria as a function of blend composition is indicated.

Jan 1, 1963

By J. L. Green

Virginia-Carolina Chemical Corp., in its Florida Operations, uses both roller mills and ball mills in dry grinding of phosphate rock. The roller mills have been in operation since 1954 in the Mining Department. The ball mills were installed and put in operation in 1960 in the Harding Concentrate Superphosphate Plant. The roller mills in the Mining Department are used to grind phosphate rock for outside customers. This involves short notice orders of varying grinds, grades and types of rock. The ball mills grind phosphate rock for use in V-C's own phosphoric acid and concentrated superphosphate plant. These mills grind generally two types of rock for one grind. In 1959, a 10% speed-up was made in the operating speed of the roller mills. This paper deals with the operational gains and resulting cost savings which evolved from this speed-up, and compares the present operations of the roller mills and of the ball mills in grinding phosphate rock. In January 1959 it was decided to determine the feasibility of reducing the grinding cost on the roller mills, per ton of rock ground, by speeding up the mill 10%. At this time, one mill was completely reconditioned so it would be in top condition. Extensive tests were then run both before and after the mill speed-up to determine the resultant cost savings. These tests showed that, due to this 10% speed-up, the mill capacity was increased approximately 20% and grinding power costs per ton were reduced approximately 10%. Table I shows the results of these tests. Each test run actually represents several of the same type rock and grind, averaged together. Each test run lasted approximately three hours. The validity of these runs has been confirmed by subsequent operation in grinding over 1,000,000 tons of phosphate rock. Accurate records have been kept on power consumption and repairs as well as tons produced. Two types of feed rock were used for the tests — pebble phosphate rock and flotation phosphate concentrate rock. The pebble phosphate rock size is approximately 80-90% plus 20 mesh. The flotation concentrate phosphate rock size is approximately 15% plus 20 mesh and 95% plus 100 mesh. The same two types of rock feed were used for all the test runs. Test Nos. 1, 2, and 3 were run at the original mill speed of 85.5 rpm on the vertical shaft. Test No. 1 was run with a feed of high grade flotation concentrates; the desired fineness attempted was 70% passing 200 mesh. Tests No. 2 and No. 3 were run with a feed of low grade pebble. Test No. 2 was run for a desired fineness of 70% passing 200 mesh. Test No. 3 was run for desired fineness of 50% passing 200 mesh.

Jan 1, 1963

By G M. Young

IT IS most appropriate that this first Memorial Lecture should be given in the Province of Quebec, near the site of the first metallurgical industry in Canada. At La Forge, about seven miles north of Three Rivers, iron was produced in 1783. We are told that the early settlers obtained most of their iron-ware -stoves, kettles, axes and ploughshares -from this smelter, with its foundry and forge. The Canadian copper industry also had its beginnings in Quebec when, nearly 100 years later, in the 1880's, several small copper smelters were erected in the Eastern Townships. Later, in 1899, Canada's first aluminum smelter was built at Shawinigan. From these small beginnings has grown a vast metals industry, the export value of its products being only exceeded by that of our forest products -newsprint, pulp-wood and lumber. As we are not a large country in terms of population, our domestic capacity to consume is often small in relation to our developed capacity to produce.

Jan 1, 1963

By W. R. Hardwick

This paper describing the mining methods of the Inspiration Consolidated Copper Co. is one of a series being prepared by the Bureau of Mines on mining methods and costs in various mining districts of the United States. The story of mining at Inspiration is of particular interest because, after 127,812,000 tons of low-grade copper ore were successfully mined, the mining method was changed from block caving to open-pit. As the open pit became deeper, many features of the former block-caving operation that were exposed elucidated concepts of the mechanics of caving that previously had been assumed but not observed. The conversion to open-pit mining was accomplished by unique combinations of equipment and the introduction of ingenious engineering and operating practices that have extended the expected life of the mine for many years.

Jan 1, 1963

By J M. Fletcher

The responsibility and scope of the Industrial Engineering Department, as organized at the Jeffrey mine, has been broadened to include any study, project or report that could result in more effective use of men, materials and equipment. Although still emphasizing wage incentives and co t reduction, much more varied work is now done, consistent with the in-.creased complexity of industry. Additional activities now include production, maintenance and inventory control improved job evaluation, packaging, labour utilization studies, technical sales liaison, mining, milling and service department n1ethods, plant layout, and specialized project analysis. Additional techniques include the extensive use of work .sampling and standard data. A recent trend has been toward increased emphasis on industrial relations, both in introducing change to the men and in providing requested explanations to Union stewards and officers. These new responsibilities have resulted in the development of specialists in some rather narrow industrial engineering fields, as well as the necessity for industrial engineering assistance in supervisory and job training.

Jan 1, 1963