Search Documents

By W. R. Reed, S. Klima, J. Driscoll, T. W. Beck

"Tests were conducted to determine properties of 4 foam agents for their potential use in longwall mining dust control. Foam has been tried in underground mining in the past for dust control and is currently being reconsidered for use in underground coal longwall operations in order to help those operations comply with MSHA’s lower coal mine respirable dust standard (1.5 mg/m3). Foams were generated using two different methods. One method used compressed air and water pressure to generate foam, while the other method used a low pressure air generated by a blower and water pressure using a NIOSH developed foam generator. Foam property tests comprising of a bottle shake test, foam expansion ratio, and water drainage were used to classify foams. The bottle shake tests determined that the lowest concentration of foam agent to be used was approximately 1.5%. Compressed air generated foams tended to have low expansion ratios (10-19) with high water drainage. Blower air generated foams had higher foam expansion ratios (30-60) with lower water drainage. Foams produced within these ranges of expansion ratios are stable and potentially suitable for dust control. The different foam agents produce foams with different material properties. Results of testing eliminated two foam agents for future testing because they had poor expansion ratios. The remaining two foam agents, while having different foam properties, seem to have properties adequate for dust control. These material property tests can be used to classify foams for their potential use in longwall mining dust control. INTRODUCTION About one-half of U.S. underground coal is produced by longwall mining. This technique allows for mining high volumes of coal, producing significant amounts of coal mine dust. This can lead to the overexposures to longwall miners and possibly occupational respiratory diseases black lung and silicosis, which have no cure and can be disabling or fatal. The only method to avoid these occupational illnesses is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit for respirable coal mine dust is 1.5 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities [1]. When respirable quartz is present, the mine must maintain an average concentration at or below 0.1 mg/m3. If the mine exceeds the 0.1 mg/m3 respirable quartz dust concentration, then the applicable respirable dust standard is reduced, calculated as 10 divided by the percent quartz present [2]. Respirable dust samples collected by U.S. Mine Safety and Health Administration inspectors for the five-year period from 2010 to 2014 found that 5.6% (53 of 943 respirable coal mine dust samples) of the longwall operators on the tailgate side exceeded the coal mine dust standard, and 4.3% (76 of 1768 samples) of the jacksetters exceeded the standard. If silica is present, the reduced standard is implemented, meaning that 11.4% (36 of 316 respirable coal mine samples analyzed for dust) of the jacksetters exceeded the reduced standard. Only 3.8% (18 of 478 samples) of the longwall operators on the tailgate side exceeded the reduced standard [3]. Had the 1.5 mg/m3 standard been in effect during this period, non-compliant samples would have been much higher. For example, over 15% of the samples collected at the tailgate shearer operator occupation exceeded the lower standard."

Jan 1, 2017

By S. Mischler, J. Organiscak, S. Klima, C. Seaman

"Researchers at the National Institute for Occupational Safety and Health’s Pittsburgh Mining Research Division (PMRD) performed comparative testing of six hollow cone water sprays from three manufacturers: static swirl chamber sprays from Spraying Systems (BD-3, BD-5) and Steinen-Hahn (SH-3, SH-5), and movable swirl chamber sprays from Repair King (RK-3, RK-5). Water flow testing was completed at three operating pressures (60, 80, and 100 psig) where both sets of sprays (3-series and 5-series) produced similar water flows, deviating less than 8% from the average water flow rate at each pressure. Airflow induction testing was completed at 80 psig using a hot wire anemometer to take air velocity measurements upstream of the spray nozzles. Respirable dust capture efficiency testing was completed in a 14.5-m3 (512-ft3) closed system dust chamber at 80 psig. The dust capture efficiency ranged from 7.2% to 9.9% for the 3-series nozzles, and from 5.3% to 7.1% for the 5-series nozzles. Sprays were also analyzed using a Cloud Aerosol and Precipitation Spectrometer (CAPS), which uses light scattering to count and size the airborne water droplets from each spray. In both cases, Spraying Systems sprays produced the largest mean droplet size, followed by Steinen-Hahn and Repair King sprays, respectively. INTRODUCTION Coal mine worker overexposure to respirable coal dust continues to be a problem in underground coal mining operations in the United States. The U.S. Mine Safety and Health Administration (MSHA) now requires coal mine worker respirable dust exposure to be no more than 1.5 mg/m3 average over the actual working shift (CFR 30-70.100, 2016). Potential overexposure to respirable dust by continuous miner, roof bolter, and shuttle car operators may be prevented if proper safety and health practices are implemented as detailed in the mine’s ventilation plan (CFR 30-75.371, 2016). Water sprays are a necessary component of an underground coal mine ventilation plan. They are important on the continuous mining unit for moving air and removing respirable coal dust from the breathable airstream. MSHA requires underground coal mines to include the number, types, location, orientation, operating pressure, and flow rate of operating water sprays in their mine ventilation plans (CFR 30-75.371, 2016). Water sprays can become clogged, requiring the sprays to be properly checked, maintained, and replaced in order to continue meeting the ventilation requirements described in the mine ventilation plan.In an effort to eliminate the problems with spray clogging, Repair King has developed self-cleaning movable swirl chamber hollow cone water sprays (RK-3, RK-5). The spray’s movable swirl chamber is designed to only open when water pressure is applied to the spray nozzle, preventing the nozzle from clogging. Anti-clogging sprays could improve mine production by reducing the amount of time spent servicing clogged sprays. Also, these sprays could improve health and safety of miners since they would continue to suppress and capture dust and continue to move airflow at the face, while a clogged spray loses this ability until it is cleaned or replaced manually. The objective of this research was to assess the comparability of the Repair King sprays with the most commonly used sprays in underground coal mines using performance criteria. An assessment of the sprays self-cleaning or anti-clogging capability was not conducted."

Jan 1, 2017

By James Coull, Brian Wilson, David Siddle

"In 2012, Golder Construction Inc. was awarded a Design-Build contract for the design and construction of an extensive, deep ground improvement scheme to support up to 20 metres (66 ft) high Mechanically Stabilized Earth walls and bulk earthworks required for the development of the proposed Kitimat Liquefied Natural Gas (LNG) facility at Bish Cove, British Columbia (BC). Utilizing Cutter Soil Mixing (CSM) to construct barrettes consisting of overlapping rectangular panels of in-situ cement-treated soils, a deep mixing scheme, covering an area of approximately 12,900 m2 (15,430 yd2) and comprising some 1645 CSM panels to depths of up to 30.7 m (101 ft), was developed to provide the required static and seismic stability for the LNG structures, and meet the project-specific performance criteria.CSM panels were constructed through varying thicknesses and discontinuous layers of fine-grained, very soft to soft marine deposits, and loose to compact sands, with occasional interbeds of dense sands and gravels. Panel completion criteria was based on soil response factors, as measured by the CSM equipment, with the design requiring a typical embedment of about 2 m (7 ft) into dense silty sand to sand and gravel to provide the required bearing. A total volume of approximately 73,900 m3 (96,660 yd3) of soil was treated with cement to consistently yield average unconfined compressive strengths exceeding 2.5 MPa (363 psi).This paper outlines the challenges associated with the construction and quality control of this large deep mixing scheme in highly variable geotechnical conditions at a remote location with barge-only access, and limited communication facilities. Specifically the paper will discuss the logistical challenges faced and solutions adopted for the project; equipment redundancy requirements for a 24/7 operation; the impacts of wear and tear, as well as variability in subsurface conditions on productivity; quality control processes adopted for the project, including the value of provision of an on-site laboratory; and materials handling issues, and their impacts on mix design and quality control."

Jan 1, 2017

By S. Thibeault, P. Filiatreault, B. Straight, D. Castendyk, L. Cameron

"Unmanned aerial vehicles (UAV), or drones, capable of collecting and retrieving water samples from pit lakes, tailings ponds and other mine water basins will revolutionize environmental programs by lowering sampling costs and reducing safety related risks. Costs typically include a boat and associated equipment, boat transportation, road maintenance, water safety devices, water safety training, and additional staff. Typically, the total cost can exceed $20,000 USD per sampling event (excluding lab analyses). Hazards include potential for drowning, unstable pit walls, and unconsolidated sediment surrounding tailings ponds. Hatch has developed a novel device for aerial drones which currently enables the collection of water samples from depths up to 390 ft (119 m). This system only requires a pilot, a sample technician, and a safe operations point overlooking the water body. Hatch anticipates this will reduce monitoring cost by at least 50% while improving safety, reducing staffing requirements and accelerating data acquisition. This manuscript demonstrates profiling and sample collection from a 95 ft (29 m) deep reservoir and a 377 ft (115 m) deep pit lake, and highlights the potential of this emerging technology. INTRODUCTION Working on or near water at active, closed, or abandoned mine sites is inherently dangerous. Between 1996 and 1999, the United States Mine Safety and Health Administration (MSHA) reported 17 fatalities involving drowning at US metal, non-metal, and coal mines (MSHA, 2000). Open pit mines which fill with water following mine closure, called pit lakes, present numerous risks to environmental monitoring teams including drowning, hypothermia, falls to the ground from the top of high walls, and rock avalanches resulting from steep, unstable pit walls. Some pit lakes are simply not easily accessible for ongoing monitoring. However, the routine collection of water samples from the entire water column on at least an annual basis is required to monitor the evolution of water quality over time, to verify the accuracy of numerical predictions, and to manage lake water chemistry in order to produce “treatable” influent to water treatment plants, and ultimately, produce acceptable site discharge water quality. As a product of these risks and the need for water sample, mining companies spend considerable expense on pit lake safety as part of monitoring. This includes training personnel for “on water” duties and hazards, purchasing or hiring specialized equipment and personnel (such as boats, boat operators, personal floatation devices, and mustang suits), stabilizing pit walls and maintaining safe access roads to the lake surface, employing spotters with direct communication to emergency medical services to watch sampling activities (because cell phones and radio signals can be blocked by pit walls), and utilizing redundancy to prepare for unexpected incidents and accidents. For example, one Canadian mining company requires pit lake water samplers to hold Marine Emergency Duties (MED) training to ensure the entire boat crew is sufficient and competent for the safe operation of the vessel, and uses three boats for water sampling: two on the water at all times, and one on the shoreline, ready to deploy. The costs of these safety mechanisms greatly adds to the overall expense associated with pit lake sampling. Consequently, environmental programs may need to reduce the frequency of pit lake sampling in order to keep monitoring programs within an acceptable budget"

Jan 1, 2017

By Pia-Maria Haselberger, Marc Schiemann, Christian Frühling, Nicolas Richter, Hendrik Wehner, Andreas Kaschube

"The paper provides the principle considerations for a novel vehicle class within the scope of the project Large Modifiable Underwater Mothership (MUM). The main idea for these ships is to create a highly modular building block system for the global layout. This building block system allows for a mission-dependent module assembly. For the purpose of deep sea mining for example, the range of tasks reaches from multipurpose transportation and exploration missions to supporting tasks in up to 5000 m depth, e.g. energy supply. Topics covered in this paper are related to potential missions for these vehicles, the modular layout and the structural layout of a separate block module. The paper closes with a conceptual design example for this class.Index Terms—MUM, UUV, underwater mother ship, autonomous underwater vehicle, modular, deep sea, conceptual designI. INTRODUCTIONAs one of the leading economic nations, Germany is in need of energy and raw materials. In the 21st century, marine resources are a prominent and promising alternative to land based resources. However, there are challenges that need to be considered. Rough and often poorly plannable weather conditions prevail distant to the marginal seas. Ice coverage makes offshore services inefficient and costly in Polar Regions. The average ocean depth of 3500m and the associated environment conditions cause difficulties in fulfilling tasks in the deep sea. The project Large Modifiable Underwater Mothership (MUM) [1] will enable more efficient solutions in order to accomplish undersea duties and services in harsh conditions.This joint project comprises workshares from Atlas Elektronik, EvoLogics, thyssenkrupp Marine Systems, the University of Rostock and the Technische Universität Berlin. The principle idea of the project is the conception of a novel vehicle class. With highly modular autonomous underwater vehicles, this class will be capable of undertaking a variety of different tasks. Classically engineered vehicle structures will be split into single basis modules which can be flexibly assembled with specialized mission modules to form potent systems for individual assignments. The group of basis modules consists of units for navigation, vehicle control, propulsion and energy generation via fuel cell technology. The potential reusability of system relevant modules leads to a significant cost reduction and to shortened development periods compared with conventional vehicle concepts. The integration of newly designed additional mission modules is possible with little effort and a separate commercialization of single modules is feasible."

Jan 1, 2017

By M. S. Safarzadeh, V. Agarwal

"The solvent extraction of cerium(III) and samarium(III) from mixed solutions of all rare earth elements (REEs) except promethium using PC88A (2-ethyl hexyl phosphonic acid mono-2-ethyl hexyl ester), an acidic extractant, was investigated. The effects of aqueous equilibrium pH, various acids (sulfuric acid (H2 SO4 ), hydrochloric acid (HCl) and nitric acid (HNO3 )), initial metal ion concentration and extractant concentration on the solvent extraction of Ce(III) and Sm(III) were systematically studied. From the experimental results, HNO3 and HCl were found to be the preferred aqueous media for the solvent extraction of both Sm(III) and Ce(III). The most promising experimental conditions of pH, PC88A concentration and metal ion concentration were identified for the extraction of Ce(III) and Sm(III). Separation results showed that H2 SO4 at pH 2 provided the best separation between Sm(III) and Ce(III). IntroductionIn recent years, demand for rare earth elements (REEs) has increased significantly because of their many commercial applications. REEs have especially important high-tech applications owing to their unique physical and chemical properties, and they are used in a wide range of areas such as catalysts, ceramics, magnets, lasers, glass, neutron absorption and alloys. As REEs have very similar physicochemical properties, their separation and purification from each other is challenging and gaining significant interest. Samarium (Sm) and cerium (Ce) are found in different REE minerals, including bastnäsite ((Ce,La,Nd(CO3)F), xenotime (YPO4) and monazite ((Ce,La,Nd,Th)PO4) at major production sites in the United States and China, as listed in Table 1 (Bleiwas and Gambogi, 2013). The most common acidic organophosphorous extractants used for REEs extraction and separation are DEHPA (di-(2-ethylhexyl)phosphoric acid), PC88A (2-ethyl hexyl phosphonic acid mono-2-ethyl hexyl ester), Cyanex 272 (bis-2,4,4-trimethylpentyl phosphinic acid) and Cyanex 301 (bis(2,4,4-trimethylpentyl)dithiophosphinic acid) (Sarangi, Reddy and Das, 1999; Surampally et al., 2012; Tian, Jia and Liao, 2013). Out of these extractants, PC88A is known for providing higher separation factors (Acharya, Mishra and Misra, 2015). El-Hefny et al. (2010) investigated the kinetics of the solvent extraction of Sm from chloride media using sodium salt of Cyanex 272 and reported the extracted species to be Sm(OH)A2•2HA. Lee et al. (2005) investigated the solvent extraction of Sm(III) with PC88A and saponified PC88A from chloride solutions and found the stoichiometry of the extraction reactions to be 1.5 with PC88A and 3 with saponified PC88A."

Jan 1, 2017

By Billy Rosseau, Mike Cammack, Richard O’Meara, Gustavo Azpilcueta

During the summer of 2014, the U.S. Army Corps of Engineers (USACE) sought proposals to vastly improve and expand the small boat harbor in Valdez, Alaska. It would be a multi-year project, and construction was scheduled to begin in the spring of 2015. One aspect of the project was the construction of a 3,100 feet (1000 m) rubble-mound breakwater to protect a mooring basin. An estimated 208,500 tons (190,000 t) of rock, ranging in size from 160 to 3500 lbs (73 – 1600 kg), were needed to build the breakwater. The Glacier Point Quarry was selected as the rock source due to its proximity to the project and the quality of the rock meeting all of the USACE rock standards.

Jan 1, 2017

By Tamara Wiseman, David Stewart

"A Quarry located in Georgia is a green-field site established in 2011. The quarry lies in the eastern part of the Georgia Piedmont area. It is within a distinctive, northeast-trending belt of relatively high-rank metamorphic rocks known as the Kiokee Belt, a poorly mapped sequence of units that largely consists ofamphibolite and various schists and gneiss that are host for relatively young granite bodies andassociated pegmatite and aplite dikes."

Jan 1, 2017

By K. M. Mayhew, G. D. Barr, T. M. McCoy, C. T. Knilans

"Teck Resources Limited (“Teck”) has developed and extensively tested on a continuous basis the CESL Technology hydrometallurgical process for treating copper and nickel sulphide concentrates, including bulk copper-nickel concentrates. Copper, nickel and cobalt are leached efficiently into solution, utilizing CESL process conditions. Total precious metals including gold, silver, platinum and palladium are recovered from the residue stream via sulphur flotation. This paper describes the CESL Technology testwork on a bulk copper-nickel concentrate derived from Twin Metals Minnesota?s (TMM) deposits within the Duluth complex and evaluates the economic benefits (increased cash flow, increased revenue certainty) and investment criteria (capital cost, payback and cash flow) of incorporating CESL Technology into the staged development of TMM?s deposits.INTRODUCTION Mineral Processing and the Role of Hydromet in the Duluth Complex The Duluth Complex in northern Minnesota, United States (US), represents one of the largest undeveloped accumulations of copper, nickel, gold, and platinum group metals (PGMs) in the world, ranking second in copper and PMs and third in accumulation of nickel. The figure below identifies some of the larger known deposits within the Complex (see Figure 1). Copper, nickel, PM and PGM mineralization within the Duluth Complex is hosted by mafic to ultramafic intrusive rocks that are part of the overall intrusive complex.One of the mineral processing challenges of Cu-Ni-PM-PGM deposits in this Complex is the complicated, polymetallic nature of the mineralization1: copper occurs primarily as chalcopyrite and cubanite with minor occurrence of talnakhite; nickel occurs as pentlandite and refractory nickel oxide/silicates; iron sulphides are present as both pyrrhotite and troilite; and PMs/PGMs occur in both the sulphide matrix as well as discrete minerals. An additional challenge for the Duluth Complex is the ratio between copper and nickel; in most of the identified deposits, copper grade is three to four times greater than the nickel grade, which precludes the production of a simple bulk concentrate due to the lack of a traditional smelting market for a bulk concentrate of this character."

Jan 1, 2017

By Brian Wilson, Megan Atkinson, Richard Diggle, Nathan Sweeney

"Ruskin Dam, located near Mission, British Columbia, was constructed in 1929 and 1930 and comprises of a concrete gravity dam structure founded on bedrock. At the right abutment, which consists mostly of dense to very dense sands and silt, the dam abuts against overburden soils, and connects to a cutoff wall system consisting of sloping concrete slabs. Significant seepage and piping issues were encountered during first filling of the reservoir in 1930. In 2012, BC Hydro, the owner of the dam, awarded a contract for the construction of seepage control measures at the right abutment, including construction of a plastic concrete cut-off wall extending upstream of the dam, a plastic concrete seepage training wall extending downstream of the dam, tie-in of the new cutoff wall to the dam, consisting of jet grouting of the soils adjacent to the dam to allow for the construction of the special cutoff connecting the cutoff wall to the dam, and construction of additional jet-grouting ground improvement downstream of the dam.Integral to the upgrade was the requirement for the special tie-in cutoff wall, consisting of a highly flexible, impermeable membrane to connect the concrete dam to the new, 1 m thick plastic concrete cutoff wall. The tie-in extends vertically into bedrock through the dam and jet grout columns constructed adjacent and beneath the overhanging portion of the dam at the right abutment. The membrane is required to survive the anticipated earthquake induced deformation between the dam and the abutment soils.This paper describes the processes used to develop a material suitable to meet the specified flexibility and permeability criteria, as well as the innovative construction techniques utilized to construct the slot and place the bituminous material within it. The final dimensions of the slot were in the order of 7 m long by 25 m deep by 0.17 m wide. The bituminous material was placed under a head of water which was required to maintain stability of the slot, and was placed at temperatures in excess of 120 degrees Celsius."

Jan 1, 2017

By Pierre Gouvin

"This paper discusses real time monitoring of utility vaults during the reconstruction of the Elliot Bay Seawall in Seattle. The project, undertaken because deterioration of the old wall posed increasing risks to property and lives, impacts businesses, ferry terminals, a rail line, and electrical utilities that distribute power to much of the downtown area. The project, which has been fast tracked to minimize risk and commercial impacts, involves multiple contractors with heavy machinery working in an area one mile long and only a few hundred feet wide. This presented challenges to monitoring of the utilities, as will be discussed in the paper.INTRODUCTIONThe Elliot Bay Seawall (EBSW) was built in over a period of 18 years, starting in 1916. It consisted of a vertical concrete wall placed on a timber pilings and timber relieving platform. The seawall also retained fill that served as the foundation for a road known as the Alaskan Way. The seawall has performed well over the years, but now cracks in the concrete have allowed loss of fill, and the timber piles and support structures have been weakened by marine boring insects.The project to replace the seawall was undertaken because deterioration of the old wall posed increasing risks to property and lives. Because the project impacts businesses, tourism, ferry terminals, and a rail line, it was given a compressed timeline - 36 months from start to finish. In addition, construction activities have been staged carefully to minimize disruption of Salmon and other wildlife living in Puget Sound. In fact, will incorporate several habitat improvements to promote sea life, such as a nature-imitating textures in the surface of the wall and a glass deck structure that allows sunlight to reach the water. (Fig. 1) shows a schematic of the planned new wall.The sheet piling, concrete piles, jet grouting, drilled shafts, ground freezing, and demolition activities are all taking place in the narrow corridor that holds the subsurface ducts and vaults protecting Seattle’s electrical power distribution. If the network of duct bank and vaults were to experience differential settlement during work here, then most of downtown Seattle would be in the dark. Thus it was important to provide real-time displacement monitoring of these utility structures."

Jan 1, 2017

By Stephan Fisch, Franz-Werner Gerressen

"The use of cut-off-walls (COW) for the open pit coal mines has been used for decades. They have been used to reduce the negative hydraulic impact to the surrounding area caused by the open pit mining. The pile-guided trench cutting system is a worldwide unique technique, originally developed by the engineers of the mining companies themselves. It guarantees a continuous, joint free, COW during a continuous installation process. At this specific site in Welzow, this technique has been pushed to new limits in order to address the local lake region. Depth capability has been designed to about 430 ft (130m), proven are already depth of about 360 ft (110m) at a constant trench width of 39 inch (1000 mm). This project is approximately. 6.8 miles (11 km) long of COW, scheduled to be completed in 12 years period. About 2.05 miles (3.3km) have been installed, which is equivalent of about 3.5 Million ft² (330,000 m²). The system flushes special clay which forms a filter crust at the inner surface of the trench. Only natural clay resources used, in order to achieve the cut-off effect (colmation effect). The paper explains the installation process of the cut-off-wall as well as the equipment systems developed specifically for this project. After a successful start of the first phase of the project, the next step in the advancement of the equipment is already underway to enable the installation of greater depth to approximately 490 ft (150 m +) and beyond. The next generation equipment system is scheduled to start operation around 2018 INTRODUCTIONThis Serbian saying “Bóh je stworil Lužicu a cert je zaryl brunicu – God created Lusatia and the devil buried brown coal underneath it.” captures local communities’ ambivalence towards lignite.Lusatia is an almost entirely flat stretch of land between the Elbe and Neiße rivers dominated by glacial sands. On the surface, the heathland and woodland is hardly noteworthy. However, three large lignite mining regions, two in Brandenburg and one in Saxony, in the east part of Germany, divert the attention to underground level, down to depths of up to 120 meters. Here, seams crisscross the earth like ribbons. They were formed in the Tertiary around 17 million years ago.The mining of the lignite started almost 200 years ago. To enable open pit mining, a suitable dewatering system was required. At first, wells and drainage system were used. With the increasing demand to go deeper to enable full use of the existing resources with greater mining depth, a decision taken back in the 60th of the last century, the amount of water which had to be pumped increased dramatically. In peak times, approx. 1.57 Billion cubic yards per year (1.2 Billion m³/year) had to be pumped. This led to a lowering of the groundwater level for up to 230 ft (70 m), impacting the regional lake landscape. In order to reduce the influence on the water balance, and bring the water level back to pre1970th, a first development took place to implement the use of specific COW system to depth of about 147 ft (45m)."

Jan 1, 2017

By J. Peterson, P. G. McKneight, R. W. Riggle

"In today’s tough mining environment, the key difference between surviving and thriving is how effectively miners optimize their mining operations. This paper explores the compounding effects material fragmentation has on mining costs and productivity. Starting with Drilling & Blasting and moving through Loading, Hauling and Crushing, we will illustrate the opportunities to improve operating costs and thus reduce the Total Cost of Ownership (TCO) of the total mining system. Material size and volume requirements are defined by the needs of the mill or plant, and drive the rest of the mining operation from the bench through the primary crusher. At the start of the cycle, where the rock mass is drilled and blasted, the degree of fragmentation and the muck pile configuration is determined, as are the effects on cost and productivity of all subsequent operations. The cost of managing oversize material, including secondary handling, overloading, reduced diggability, higher load factors, extra pass loading, increased wear factors and reduced throughput rates are all opportunities for improvement. INTRODUCTION Having visited many mine sites, customers are asking about the end to end mining value stream from loading to the crusher and how to measure the cumulative effects on each part of the mining value chain. All too often improvements with the drilling and blasting may impact fragmentation but do not improve the diggability so the net change on cycle times or fill ratios is perceived to be negative at the point of loading but they may have a measured improvement going through the primary crusher. This makes it imperative to measure performance at each segment of the overall cycle and not just to the crusher but thru it. The mine material process originates with solid rock, in-situ, and progresses to the output of the primary crusher. Once the material has passed the primary crusher the fragmentation size will be fairly consistent and promote consistent throughput of the plant or mill. In late 2015 a team was conducting a reassessment visit to a mining site where we had conducted the original assessment the previous year. Though many recommendations had been implemented some had been so recent they had not resulted in the expected improvements. Several of our discussions kept returning to the impact fragmentation has to both the individual components of the mining cycle but also the effects compounded throughout the end to end process. Let’s move on to the big picture before we zoom in on any specific operation. To get from native solid rock in the ground to a concentrate or a saleable rock product we have the same steps from one end of the chain to the other. We start with a good geological understanding of the rock type, characteristics and structure to design a program to drill and blast the rock. The height of the bench is relevant to the annual production requirements and the specific digging equipment models best sized to make that production possible. The equipment selection influences the bench height which has a minimum and maximum hole diameter to maintain a safe blasting operation. The diameter of hole burden and spacing all contribute to a good distribution of explosives in the rock mass that maximize the fragmentation and preconditioning of the rock when blasted. The timing and sequencing of hole initiation will yield a fragmentation ratio and diggability factor. Fragmentation size adjustments will change the meters drilled per cube and the explosives consumption will change accordingly. Drill cost is measured by meter drilled so a direct relationship exists between cost and fragmentation sized achieved."

Jan 1, 2017

By T. J. Morris

"From November 2014 through September 2016, Westmoreland’s Coal Valley Mine utilized a Marion 7450 electric walking dragline to extract 1.2 million tonnes of a vertically-dipping, 52-meter wide, fault-thickened seam, beneath a conventionally-excavated pit bottom. Mine planning and operational hurdles encountered throughout a kilometer of mined strike length included mitigating highwall instability in both hanging and footwall slopes, water management, and end-of-life machine reliability and maintenance. The most substantial challenge has been the depressed global coal market. However, the successful application of this mining method significantly aided the overall cost of production at the site. The valuable experience gained from this project will be extended to future mining areas where this technique can be similarly applied. INTRODUCTION Coal Valley Mine is located approximately 220 kilometers southwest of Edmonton, Alberta, Canada, in the foothills of the Rocky Mountains. Since commercial production began in 1978, more than 84 million clean tonnes of coal has been produced and sold domestically as well as exported overseas for power generation. While the existing processing plant has a nameplate capacity of 4 million tonnes per year, the site has operated at a 2 million tonne rate since 2015 due to depressed export markets. Westmoreland acquired the mine as part of its purchase of Sherritt Coal Operations in April 2014. The mine operates 24 hours a day, 7 days a week, with an IUOE workforce of 261. GEOLOGICAL SETTING The geology of the Yellowhead Tower mining area differs significantly from previous mining areas at Coal Valley. The Mynheer coal seam discussed herein consists of steeply dipping, highly-sheared, thrust-faulted, and heterogeneous coal pods. Deep set, southwest striking thrust faults were the likely mechanism for the podding and have resulted in overturned, rolled and highly sheared seams with zone thicknesses of up to 65 meters.The hanging wall is characterized by soft bentonitic mudstones and siltstones, overlain by massive competent sandstone. The footwall is defined by a hard volcanic tuff, interbedded with thin, sporadic coal seams. The sandstone above and volcanic tuff below constrained the faulting system within this zone, enabling the mass podding that has afforded the opportunity for large-scale mining."

Jan 1, 2017

By Alireza Ayoubian, Douglas S. Roy, Gianni O. Chieruzzi

"A 400 MW, gas-fed power plant on floating piles and piled raft foundations was constructed in the Province of Moskovskaya, Russia in 2008. The subsurface is characterized by fill underlain by loose to medium dense alluvial deposits, with peat and clay interbeds, a stiff to hard, highly plastic, silty clay stratum of glacial origin, and a stratum of very dense, varved interbeds of sand and silt.More than 800, drilled concrete piles were constructed at the site. The pile length ranged from 15 to 23 meters below existing surface grade, and the pile diameter ranged from 0.9 to 1 meter.Initial analyses by others predicted total power plant settlements of 3 to 4 cm when subjected to the permanent loading conditions. Under a peer review process for the equipment supplier, subsurface investigation and testing were performed to verify the consolidation parameters used for foundation design of the power plant foundation. The parameters obtained in this investigation were used in the 3-D finite-element model ELPLA as inputs for the settlement analysis of the turbine building and power island. The ELPA analyses predicted settlements on the order of 7 cm over a period of 30 years. The actual settlements after two years of monitoring were compared against the model predictions. The rate of settlement and the recompression index were both underestimated in our model. The measured settlements have enabled us to calibrate both of these model parameters so that the model better matches the data.IntroductionA 400 MW, gas-fed power plant was constructed near Moscow in the Province of Moskovskaya in Russia.Figure 1 shows the general arrangement of the main structures, and the geometry of the piles supporting those structures."

Jan 1, 2017

By R. J. Matetic, J. Noll, C. Zhou, J. DuCarme, M. Reyes, J. Srednicki

"In April 2016, MSHA began requiring the use of continuous personal dust monitors (cPDMs) to monitor and measure respirable mine dust exposures to underground coal miners. After the cPDM’s implementation, mine operators discovered that it interfered with proximity detection systems (PDSs), thus exposing miners to potential striking and pinning hazards from continuous mining machines. NIOSH was sought out by MSHA and mining industry stakeholders to determine how the cPDM and PDS interact with each other. Accordingly, NIOSH investigated existing standards, developed test protocols, designed experiments, and conducted lab evaluations. Some interferences were observed to be caused by electromagnetic interference (EMI) from the cPDM. Results showed that there was no significant interference when the cPDM and the miner-wearable component of the PDS were separated by distances of 6 inches or greater. In this study, the cPDM and PAD needed to be at least 6 inches apart in order for them to be used simultaneously and reduce interference potential. INTRODUCTION Underground coal miners are exposed to a variety of hazards on a daily basis such as coal dust exposure, high noise levels, roof and rib falls, the potential for fires and explosions, and operating and working with heavy machinery. One of the hazardous jobs is operating or working nearby a continuous mining machine (CMM). According to Mine Safety and Health Administration (MSHA) statistics, 40 miners have been fatally struck or pinned by a CMM since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are required on all operating CMMs in underground coal mines, with the exception of full-face CMMs, by 2018 (1,2). Proximity detection systems (PDSs) are designed to alarm miners and stop machine motion in order to protect miners from being struck, pinned or crushed by CMMs(3). Currently, MSHA-approved PDSs, installed on CMMs, are based on the principle of magnetic flux density (B-field) (4,5). The system generates a magnetic field around a CMM and determines the relative distance a miner is from the CMM based on a detected magnetic flux density. A PDS typically consists of multiple magnetic field generators mounted at different places around the CMM, and personal alarm devices (PADs), which are worn by the miners to detect the magnetic flux density. When a miner, wearing a PAD, gets closer to the machine, the PAD detects a stronger magnetic field from the generators and detects a weaker magnetic field when a miner moves away from the machine. The magnetic field generators installed on CMMs typically produce modulated magnetic wave signals at frequencies between 10 kHz and 120 kHz. The magnetic fields are measured by three small magnetic coil antennas mounted on orthogonal axes inside of the PAD worn by the miner. According to Faraday’s Law, the changing magnetic field induces a voltage in each coil antenna, and the voltage values are transmitted from the PAD back to a controller on the CMM wirelessly, typically at a frequency between 400 MHz and 2.5 GHz. These values are then used to determine the distance between the miner and the generators of the machine. Typically this information is used to determine when a miner wearing a PAD is in a warning zone or stop zone which would trigger different alarms and actions such as slowing the machine down or stopping it."

Jan 1, 2017

By Joshua Hescock, Zach Agioutantis

"The Surface Deformation Prediction System (SDPS) has been developed as an engineering tool for the prediction of subsidence deformation indices through the implementation of an influence function. SDPS provides a reliable and fast method for the prediction of mining-induced displacements, strains, tilt, and so forth at any elevation between the seam and the horizontal or varying surface topography. One of the key aspects in obtaining reliable ground deformation prediction results is the determination of the edge effect offset. The value assigned to the edge effect corresponds to a virtual offsetting of boundary lines delineating the extracted panel to allow for roof cantilevering over the mined out area. The objective of this paper is to describe the methods implemented in updating the edge effect offset code within SDPS. Using known geometric equations, the newly developed code provides a more robust calculation of the offset boundary line of the extracted panel for simplistic, as well as more complex, mining geometries. Assuming that an extracted panel is represented by a closed polyline, the new edge offset algorithm calculates a polyline offset into the extracted panel by the user-defined edge effect offset distance. Surface deformations are then calculated using this adjusted panel geometry. The MATLAB® program was used for development and testing of the new edge effect offset feature. In completing rigorous testing regimes, the new offset features will be integrated into SDPS, further increasing the speed and reliability of the programs resulting in a retrospective increase in capability and flexibility. INTRODUCTION Underground operations have been known to cause mining-induced subsidence inside and outside of the mine permit area (Karmis, Agioutantis, and Andrews, 2008). Additionally, subsidence can impact surface water bodies, such as rivers, streams, lakes, and wetlands (Karmis and Agioutantis, 2015; Newman et al., 2016), as well as infrastructure, such as roads, railroads, pipelines, and buildings. With an increase in regulatory focus on mining-induced impacts to local structures, the calculation of mining-induced subsidence indices has become necessary in determining potential damage and mitigation efforts. The accurate prediction and evaluation of mining-induced ground deformations is required to obtain underground mining permits due to potential impacts to nearby structures, as well as hydrogeological sources. The prediction of ground deformation indices is often a complex task due to the number of input parameters required, such as mining geometries, overburden lithology, surface topography, the rate of mining (Karmis, Agioutantis, and Andrews, 2008)."

Jan 1, 2017

By A. Chieregati

"A heterogeneity study was conducted at Erdenet Copper Mine in Erdenet, Mongolia, to determine the fundamental sampling error associated with blasthole sampling. Using a custom designed sector sampler, six large blasthole samples were collected to perform the test that was developed by Pierre Gy, to estimate the constitutional heterogeneity factor for several types of ore. The study investigated the entire sampling protocol, from mine site to analytical laboratory, and quantified the contributions to fundamental sampling error (FSE) of the various stages of sampling and sample preparation. The total relative standard deviation (RSD) of sampling error was determined to be ±32% and ±49.4% for copper and molybdenum respectively. A classical statistics analysis conducted on the data confirmed the level of RSD. About 95% of the sampling error was produced from only one step in the sampling protocol: when the 1 kg sample was reduced to 50 g sample for chemical analysis. Therefore, it is recommended that the 1 kg sample be reduced to 50g using a slightly different protocol to minimize the FSE. The 1 kg sample should be first crushed to 0.2cm size. A 250g split should then be taken and fine ground. A 50g split should then be taken from the 250g fine ground split. These two simple steps will reduce the FSE to ±7.9% and ±17% for copper and molybdenum respectively. The modified sampling protocol effectively reduces the probability of misclassification of low grade ore to zero. INTRODUCTION The Erdenet copper-molybdenum open pit mine is located in Erdenet, in Orkhon province, Mongolia. The Erdenetiin-Ovoo copper-molybdenum deposit is between 1.5 and 3 km wide, and about 25 km in length (Erdenet Mining Corporation, 2016). Chalcopyrite, bornite covellite and chalcocite are among the major minerals found in the deposit. The mine processes approximately 26 million tons of ore annually. A study was conducted to evaluate the fundamental error associated with the blasthole cuttings and sampling protocol at the mine. The open pit mine uses 215mm diameter Russian drills to drill 17.5m holes for 15m benches. The total weight of blasthole cuttings for a 215mm diameter hole and 15m bench height is between 1.5 and 2 tonnes. This amount of sample is difficult and time consuming to collect and analyze. Therefore, a sector sampler was designed for the Russian drills to collect large samples that were representative of the blasthole cuttings (Ganguli et al., 2016). In order to eliminate the delimitation and the extraction errors, researchers consider sector samplers to be ideal for sampling blastholes (Pitard, 2008; Chieregati and Pitard, 2009). This method was intentionally more rigorous than the blasthole sampling protocol at the mine to ensure that the blasthole cuttings were properly sampled. This study was part of a broader study that also looked at the relationship between particle size and grade. The samples collected by the custom designed sector sampler were very large (195 kg on average), and therefore, sufficient for both studies. The relationship between particle size and grade has been reported in Ganguli et al. (2016)."

Jan 1, 2017

By A. Montera, M. Loken

"The process of blending consistent and predictable feed for the roasters is critical for optimizing product quality and controlling production costs. To assist in this process, online PGNAA slurry analyzers have been installed and evaluated at a Sudbury Ontario smelter. They are used to measure 100 % of the full process stream to obtain elemental composition data in real time. This paper explains the application details at Sudbury and the benefits achieved from their full stream, elemental slurry analyzers.INTRODUCTIONSudbury Integrated Nickel Operations (Sudbury INO), a Glencore Company, consists of two underground nickel/copper mines in Sudbury, Nickel Rim South and, Fraser, along with the Strathcona mill and the Sudbury smelter. The facilities are spread throughout the 60 kilometer-long, oval-shaped geological formation known as the Sudbury Basin (Figure 1). The company has been mining nickel-copper ores in the Sudbury area since 1929. Nickel and copper are the primary focus of operations at Nickel Rim South and Fraser. Other base metals such as cobalt and precious metals are also produced.The Strathcona Mill receives ore from Nickel Rim South, Fraser, and third-party miners to produce two concentrate streams. One is a nickel-copper concentrate for use by the Sudbury Smelter; the other is a copper concentrate which goes to other Glencore operations for smelting and refining. The Sudbury Smelter converts the mineral concentrate into a high grade matte containing nickel, copper, cobalt and platinum group metals. This matte product is shipped to Glencore's Nikkelverk refinery in Norway for further processing. In 2015, the Sudbury INO Smelter completed the first phase of the Process Gas Project (PGP); a series of process changes and capital investments designed to reduce sulphur dioxide (SO2) emissions in accordance with Ontario Regulation 194. A critical element of the planned emissions reduction was the elimination of a higher percentage of sulphur contained in input concentrate streams, which can then be captured and converted to sulphuric acid."

Jan 1, 2017

By C E. Johnson, S Hosein

Previous researchers have put forward two different theories as to the origin of air overpressure from quarry blasting. In 1980, Siskind et al postulated that the initial face movement gave rise to the displacement of air and that this resulted in the air overpressure pulse. However in 1990 McKenzie et al carried out research that indicated that the air overpressure pulse came into being as a consequence of the shock wave created by the detention of the explosive charge in a blast hole. In an attempt to evaluate these hypotheses, an investigation was undertaken over a 4-year period with the aim of determining the precise origin of air overpressure. The research was carried out at a chalk quarry in the North of England.

Jan 1, 2017