Search Documents

By Michel Jébrak, Claude Bellehumeur

Abstract - Regional and orientation geochemical stream sediment surveys were carried out by the Quebec Department of Energy and Resources in southwestern Quebec, over a part of the Mont­ Laurier Terrane of the Grenville Province. The area contains some small stratiform zinc deposits. The response of Zn mineralization to geochemical surveys is weak; the known mineralization is not defined by anomalous samples and consistent patterns. This study uses a technique that increases the geochemical signature of Zn mineralization in filtering out geochemical background components related to lithologies and surficial conditions. The background variations were modelled using principal component analysis, and the filtering technique consists of the partial reconstruction of the data matrix from results of principal component analysis . The filtering procedure considerably enhances the Zn anomalies located in the catchment basins of Zn deposits, and defines some new anomalies in proximity to the marbles of the Mont-Laurier Terrane, the principal metallotect of Zn mineralization.

Jan 1, 1993

By C. C. Stewart

Jim Walter Resources, Inc. operates four underground coal mines in Alabama. In 1986, during longwall recovery operations, sparks from a torch ignited methane that migrated onto the face after a roof fall. The fire quickly spread to the gob at the tailgate end of the longwall. The fire was successfully "area" sealed and mining operations resumed after five weeks. However, several problems were encountered during this process. This paper describes the events following the fire, methods used to control the situation, problems encountered, and steps taken to ensure preparedness for any future occurrences of this type.

Jan 1, 1993

By D J. P Jordan, C V. B Cuningham, A J. Rorke, C G. Ladds, O L. Davey

"During the early stages of the boxcut mining at the Arthur Taylor Colliery, Open Cast Mine(ATCOM), problems were experienced with blasting results. Very large boulders andportions of completely unfragmented rock were commonly encountered. A full blastmonitoring programme was instigated by the mine and the explosive supplier to solve theproblems and to optimise future blasting operations at the mine."

Jan 1, 1993

By L. L. Rethi

The U.S. Bureau of Mines summarized injury data for independent contractor employees working at all locations of coal and metal-nonmetal mines from 1983 through 1990. During the eight years, the greatest contrast in degree of injury between independent contractor and operator employees was in fatalities. From 1983 through 1990, there were 132 independent contractor employee fatalities in the mining industry. In 1988 though, independent contractor employees accounted for nearly one-fourth of all mining fatalities. The fatality incidence rates of independent contractors were consistently higher than those of operators during the eight years. For instance, in 1990, the contractors' rate was twice that of operator employees in coalmining and nearly five times that of operators in metal-nonmetal mining. Three other salient facts highlight the independent contractor employees' fatality injury data during these years. First, 82% of the independent contractor employee fatalities occurred at surface locations. Second, two job classifications?truck driver and equipment operator?represented 37% of the fatalities throughout the 8-year period. And finally, four accident classifications?powered haulage, slips and falls, machinery, and electrical?accounted for 71% of all independent contractor employee fatalities.

Jan 1, 1993

The individual or company director who ignores his or her obligations under the Resource Management Act 1991 and under the proposed hazardous substances legislation, ignores them at their peril. Two recent cases in Canada and the United Kingdom concerning environmental offences under similar legislation illustrate the risks well.

Jan 1, 1993

By G. Le Bel

The paper proposes three methods to determine optimum lifetime of a mining project1. The conclusion is that the three methods arrive at the same optimum production rate (by coincidence). It is also stated that: "The stochastic and option pricing models, in addition to providing a more realistic optimum mine life than the traditional NPV (net present value) calculation, showed that the example project has the potential for substantially higher return. By explicitly considering a project's potential risks, the stochastic or option pricing techniques can more accurately describe its probable investment performance." This discussion is intended to demonstrate that: • It is no coincidence that the three methods arrive at the same optimum production rate. • The stochastic and option pricing models do not provide a more realistic optimum mine life than the traditional NPV calculation. • The potential for a substantially higher return is misrepresented. First, a review of investment decision theory in mining is needed. Net present value is the preferred performance measure because of the flexibility offered when comparing various alternatives. However, it presents the following disadvantages: • The discount rate selection is not straightforward. • The NPV obtained represents a deterministic characterization of the variables included in the cash flow calculations, i.e. a single-point estimate.

Jan 1, 1993

By John E. Shively, Tracy K. Lundin, Francis Fong

The Superconducting Super Collider (SSC) features two 20 TeV counter rotating proton beams which will be housed in 87 km (54 miles) of tunnel. Four additional lower energy particle accelerators will be housed in 26 km (16 miles) of tunnel and underground structures. Physics experiments will be conducted in two underground detector halls approximately 67 m (220 feet) deep with footprints measuring about 30 m (100 feet) by 100 m (330 feet). Definition and design of underground facilities is advanced with construction of approximately one-third of the SSC program underway. This paper presents an overview and status of the SSC project.

Jan 1, 1993

By Mary E. Cocklan-Vendl

Regulatory processes associated with development of major mining operations in Alaska and British columbia were evaluated using specific case studies. Included were one hard rock mine in Alaska (Red Dog Mine), one hard rock mine In British Columbia (Snip Mine), and one offshore gold dredging project in Alaska (WestGold SIMA). Based on a comparison of the three case studies, it became clear that the primary incentives for cost effective permitting are: 1) early and continuing coordination of proposed project plans, designs and schedules with key regulatory agencies and local area residents and 2) development of a sufficient level of baseline information on air quality, water quality, wetlands, endangered species, fish and wildlife, and socia-cultural conditions to support the required permit application. The U.S. permitting process worked in much the same way as the Canadian permitting process. Disincentives of mine permitting include high initial costs for baseline data gathering. However, a relatively high early investment resulted in more efficient permit acquisition and reduced long-term monitoring requirements. A common problem Identified was the inadequate supply of trained agency personnel with the requisite technical and permitting experience. This sometimes resulted in poor decisions and unnecessary changes in project plans and schedules.

Jan 1, 1993

By H. Y. Sohn

The ignition and combustion of chalcopyrite particles under suspension-smelting conditions, in which the particle-particle interaction is neglected, has been analyzed by considering the intrinsic kinetics of oxidation and heat and mass transfer between the particle and its surroundings. Reasonable agreement has been obtained between the calculated results and experimental results from a laminar-flow furnace reported in the literature. This computation- al procedure has further been applied to flash-smelting conditions. Under suspension-smelting conditions (Sh = Nu = 2), chalcopyrite particles ignite at around 960 K. The effects of various parameters, such as oxygen concentration, particle size, and gas temperature, have also been evaluated. Comparison between calculated results in this work and experimental observations indicates that SO is the important gaseous product that forms at the surface of the particle.

Jan 1, 1993

By L. Alan Weakly

At a time when the US mining industry is struggling to emerge from a lengthy recession, the burden of new, unnecessary regulations could shorten the life of, or be fatal to many domestic mining companies. The possibility of new restrictions on the use of diesel equipment operating in underground mines is one example of unnecessary regulations. These could cause serious harm to the economic health of many mining companies. Whether future health-related Mine Safety and Health Administration (MSHA) regulations restricting the use of diesel equipment are unnecessary, depends on whether these restrictions are supported by fact or created in a political environment. The mining industry has benefited from the use of diesel equipment in underground metal-non-metal and coal mines for more than 50 years. Since first introduce to underground mines in the early 1940s, the use of diesel equipment has grown in numbers and size. During this time, the mining industry in America has achieved much higher productivity rates and improved safety. Although all these gains cannot be attributed to the greater use of diesel equipment, a high percentage can be. I began my professional mining ca¬reer in 1970 working in the Missouri lead mines. At that time, the use of diesel equipment was well established in metal-non-metal mines throughout the United States and many parts of the world. As director of mining research for St. Joe Minerals Corp. (now The Doe Run Co.), I was involved in research to improve mining productivity and safety. This involved investigating the better and safer use of existing or new mining methods, products, equipment and people. Within this group, diesel equipment had the single largest positive impact.

Jan 1, 1993

By W. G. Spencer, E. Sulis, P. M. Tiley

"Dome Mine's No.8 shaft is located about 1 km northeast of Dome's No.3 shaft and mill complex in South Porcupine, Ontario.No.8 shaft was brought into production in 1984 to hoist ore and waste for the complete mine as well as to service the mine from the 1600 level and below. Access above 1600 level is provided by No. 3 shaft.The rectangular shaft has six compartments consisting of two skips, a cage, counterweight, manway, and a service compartment. The over-all size of the shaft is 14 ft 7 in. by 20 ft by 7 in. (Fig. 1). A 7th compartment for shaft deepening is incorporated in the bottom 500 ft of shaft. The shaft is 5470 ft deep. The loading pocket is located at 5300 ft and the dump 61 ft below the collar.Surface facilities consist of a concrete headframe and a structural steel hoistroom which houses the cage and production hoists . The service hoist is a 12-ft diameter double drum, with one 1750 HP DC motor, and the production hoist is a 15-ft diameter double drum with twin 1750 HP DC motors.Both hoists have a single clutch and a single reduction gear train built by Orenstein & Koppel, and equipped with Canadian General Electric drives. The cage hoist is equipped with a disc pinion brake.The skips were originally aluminum 14-ton capacity, Rolla-chute design with steel liners on three sides and 4 in. of rubber on the back, to absorb the loading impact. The original guide rollers consisted of fixed 10 in. pneumatic tires. The face-to-face units were eventually replaced with larger airplane-type tires mounted on a spring loaded pivot arm."

Jan 1, 1993

By Mozley R

Contaminated sediments are a multinational problem. A crucial factor in solving an environmental problem is knowledge of, not only the amounts of polluted soil, the contaminants involved and their concentration, but also the historical background of the problem. Processing polluted soil is a tailor made activity based on rational decisions resulting from a detailed treatability study. Lack of information about characteristic properties of a specific sludge/pollution combination is the main obstacle in the route from first ascertaining that a particular harbour subsoil is polluted, to final identification of the full scale treatment plant. In the first instance, information must be generated regarding the distribution of pollutants in relation to the distribution of the original geophysical components. Based on this information rational decisions can be made on separation at a particular cutpoint and what sequential techniques should be involved for a certain fraction. For this purpose a `fingerprint method' is presented especially developed for investigation of polluted soil and sediments. The heart of the fingerprint method is a series of sequential hydrocyclone separations, by which a series of products is generated. The objective of the fingerprint method is to select an optimised treatment procedure in which the pollutants are concentrated in as small a volume of material as possible, leaving the bulk of the material clean. The pollutants can then readily be destroyed or isolated from the environment. The philosophy and advantages of the fingerprint method are demonstrated for a harbour sludge containing heavy metals as main pollutants. Hydrocyclone separation combined with flotation of both the coarse and fine fraction resulted in reusable and dischargeable products. Flotation of the fraction of fines was carried out by means of an experimental flotation cyclone enabling the selective recovery of mineral particles with diameters less than 10 microns. The overall conclusion is that design and engineering of treatment flow schemes for polluted dredged materials is a tailor made activity based on rational decisions resulting from the fingerprint information.

Jan 1, 1993

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

4.1 THE GENERAL COMPOSITION AND PROPERTIES OF CLAY-BASED GROUTS Clay-based grouts are visco-plastic systems; they are made by adding structure-forming reagents to a clay mineral mortar. Small amounts of cement and various chemical ad¬ditives constitute the reagents. If necessary, fillers also are added. The distinguishing feature of clay-based grouts is that throughout their entire stabilization period they do not form a crystallized structure as does cement grout. The structure of stabilized clay-based grouts does not deteriorate during minor rock movement or upon the initiation of blast¬ing during the construction of a shaft or a drift. Because they can possess good rheological properties during the ini¬tial structure-forming period relative to cement grouts, clay¬based grouts are not easily eroded from large fractures and karstic cavities by flowing ground water. In addition, their finely dispersed clay particles facilitate a greater fracture penetration capacity, especially in dual porosity rocks. Numerous investigations of the structural-mechanical and rheological properties of clay-based grouts by STG have demonstrated that the most effective grouts for pre¬venting the inflow of ground water into underground work¬ings are grouts that have a cement content of 8 to 10% (90 to 120 kg/m3) of the clay grout by mass. The grout should have a density of 1.18 to 1.30 T/m3. Various additional substances and chemicals can be added as additional fillers and structure-forming reagents. In pure ground water at temperatures above freezing, sodium silicate in the amount of 0.8 to 1 % by mass normally is the only structure-forming reagent that is necessary if the proper clay is selected and if it is available. The production process for making clay-based grout is divided into two stages: 1) the production of an initial clay mortar with specified properties and 2) the production of a clay-cement additive grout mixture using the initial grout along with the structure-forming reagents, including the ce¬ment. The properties of clay-based grouts depend on the phys¬ical-mechanical properties of the initial clay mineral, the properties of the cement and the properties of the chemical reagents that are added. 4.1.1 TECHNOLOGICAL PROPERTIES OF CLAY-BASED GROUTS The dynamic shear stress' To, the viscosity 11, the static shear stress2 0, the maximum shear stress of the structured that the rheological and structural-mechanical prop¬erties of clay-based grouts must fall within the following limits: the dynamic shear stress To = 50 to 200 Pa; the viscosity -9 = 0.02 to 0.07 Pa sec; the static shear stress 0 = 150 to 600 Pa; the plasticity strength Pm of the structure one minute after preparation (according to P.A. Rebinder's method) equals 150 to 500 Pa. The plasticity strength 10 days after preparation is ? 0.15 MPa. The general relationship of the change in the structural strength of clay-based grouts relative to stabilization time is shown in Fig. 32. The figure shows that the structure-form¬ing process for clay-based grouts is characterized by three stages. These stages correspond to the time periods required for conducting the principal operations during the injection of the grout into a fractured aquifer as described below. Stage I, corresponding to the time period T1, reflects the small development of structural strength during early stabi¬lization. During this time, the structural strength must not preclude the capability to pump the grout. The time Tl must correspond to the length of pumping time from the moment water is shut off and mixing occurs until the pump stops forcing the grout through the manifold block and pipeline into the fractured rock as described subsequently herein. Stage II, corresponding to the time interval T2, reflects a sharp but controllable increase in the structural strength of the grout. The length of time period T2 is controlled by the addition of appropriate reagents. Stage III produces the final value of the structural strength. This final strength is used to design the dimensions of the isolation curtain. Consequently, the development of grouts is guided by two principal criteria: 1) the grout must develop the highest possible structural-mechanical properties and 2) it must be able to be pumped by a piston pump prior to final stabili¬zation. Successful grouting depends to a large extent on the correct design of a grout for each specific case. It is impor-

Jan 1, 1993

By Jacqueline A. McClaskey

The U.S. Bureau of Mines (USBM) Information and Analysis Directorate collects worldwide data on virtually every commercially important non fuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The USBM's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the USBM survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

By Sureshan K. Moothedath

This paper provides a mechanistic representation for floc formation, growth and degradation and presents results from an experimental study of batch flocculation in which step changes were made in the impeller speed, flocculant addition, and slurry concentration. A discussion of the experimental results is included in terms of the mechanisms of floc formation and size-change.

Jan 1, 1993

By I. D. Reznik

Regularities of cobalt and nickel distribution between slag and matte, slag and metallic alloy on the base of concepts on exchange reaction equilibrium are considered. It is shown that the distribution of cobalt and nickel in industrial processes approaches to equilibrium one. Oxysulphiae influence on the bahaviour of cobalt, nickel and sulphur is shown. The recommendations on conduction of the processes of smelting, converting and slag cleaning based on the analysis of the methods or" non : ferrous metal separation from iron are given.

Jan 1, 1993

By R. J. Wesely

It is obvious from recent events in The Peoples Republic of China that a major effort is underway to increase trade with the Western World. The production of Gold contributes to China's ability to participate in international trade and consequently they place a high priority on increasing gold production. Many of the operating gold mines in China contain refractory ores which to date have not been efficiently treated. Figure 1 illustrates the description and location of some of the major gold mines in China. Recognizing that the technology necessary for the economic treatment of this ore has been developed in the United States and other Western Countries, China has begun to seek assistance in evaluating several potential projects. This paper will examine the recent history and current trends in developing a refractory gold treatment project in China.

Jan 1, 1993

By James DG, Turner JH

This paper describes laboratory testwork for the beneficiation of a medium grade iron ore, using Wet High Intensity Magnetic Separation (WHIMS). Factors leading to the selection of machine type for this method of separation are discussed and the design of the WHIMS section flowsheet of an iron ore beneficiation production plant are described including methods to achieve operational flexibility and adequate protection of the WHIMS separating chamber. The results of the commissioning and operation of the production plant over several years are described, together with experience developed in plant operation. Data on recovery of hematite over the full range of size fractions treated is presented and compared with data in the literature. Potential methods of improving plant performance are discussed. KEYWORDS: Iron ore beneficiation, plant design, wet high intensity magnetic separation.

Jan 1, 1993

By Renato G. Bautista

The solvent extraction separation of nickel, cobalt and their associated metals have been considered for industrial application since the early 1960's. This review of the solvent extraction processes is limited to the industrial applications, pilot plant and the more extensive bench scale studies reported in the literature. The processes with their significant chemical and technological contributions are discussed in detail whenever the information are available. The application of solvent extraction to the nickel-cobalt processing has so far been limited to the secondary separation of nickel-cobalt containing feedstocks derived from other primary nickel-cobalt separation methods.

Jan 1, 1993

By G. C. Sun

Rock mechanics properties, i.e. uniaxial and triaxial compressive strength, indirect tensile strength shear strength, Young's modulus, and poisson's ratio were collected for coal and related strata from 50 coal seams in 90 mines. The methodology of data organization and retrieval is described in details. The values and .ranges of those properties are also discussed.

Jan 1, 1993