Search Documents

By Gene E. McClelland, Dirk J. A. van Zyl

5.1 INTRODUCTION Heap leach cyanidation techniques possess considerable potential for exploitation of low-grade ores, small ore bodies, mine strip waste and tailing materials where fine grinding is not necessary for good extraction. For heap leaching to be successfu1, ore must exhibit certain characteristics, as previously discussed in Chapter 1. Primary among the necessary ore characteristics is that the ore must have good permeability after being crushed or treated and stacked into heaps if uniform distribution of the cyanide leach solution is to be achieved. Gold and silver ores containing excessive amounts of clays or fines generated by crushing are some of the most difficult to treat successfully by heap leaching. The presence of excessive amounts of slimes (generally classified as minus 50-micron or 270 Tyler mesh sieve size particles) in the heap leach feed will slow the percolation flow of the leach solution, cause channeling, or produce dormant or unleached areas within the heap. This may result in unreasonably long leaching periods and poor extractions. In extreme cases, the clays or slimes can completely seal the ore heap, causing the leach solution to run off the sides of the heap rather than to penetrate the ore heap. The problem of heap leaching ores containing fines can be aggravated during stacking and preparation of the ore heaps, because natural sorting of coarse and fine material occurs during these steps (Johanson, 1978). This phenomenon results in a concentration of ore fines at the center of individual ore piles and a concomitant concentration of larger rock fragments on the lower slopes and base of the piles. When the individual piles within the heap are leveled off prior to installation of the sprinkling system which delivers the leach solution, additional segregation occurs as the fines sift through the coarser ore particles. The segregation results in localized areas or zones with marked differences in permeability. As a consequence, the leach solutions follow the path of least resistance, percolating downward through the coarse ore regions and bypassing or barely wetting areas that contain large amounts of fines or slimes. Effective utilization of marginal gold and silver resources through heap leach processing requires the development of new methods in order to achieve more uniform size distribution during ore heap preparation and better slime control during leaching.

Jan 1, 1988

By S. M. Spottiswoode

Rock mechanics benefits of stope support in deep-level mining originate principally from the ability of the support to resist relative movements between the hangingwall and the footwall. While the role of stabilizing pillars and backfill on reducing the energy release rate (ERR) at the face is well understood on the basis of elastic behaviour of the rock mass, the effect of support on controlling movement of fractured ground around deep-level stopes has not yet been thoroughly studied. As part of a programme of studying the behaviour of this fractured ground, geophones were placed 10 m from the face on the roof and floor of a longwall stope in which packs were used as supports. It was found that differential movement between the roof and floor generally exceeds average stope movement during a seismic event. Conventional support therefore transmits very little seismic energy; this is expected to remain true until complete convergence occurs. In backfilled stopes, backfill can become at least as stiff as the fractured wall rock. This will have the effect of reducing the length of the hanging- wall beam. Amongst other rock mechanics considerations, a shorter hanging- wall beam should: (i) increase the resonance frequency of the hangingwall and thereby decrease the levels of vibration for seismic events with M > 1,0; (ii) reduce absolute vibration levels by increasing the mass of rock immediately adjacent to the stope which is shaken by seismic waves; and (iii) reduce differential movement between the roof and floor and thereby reduce cyclic strain on the backfill and on gully support.

Jan 1, 1988

By W. H. Hodgson, A. R. Preston

"Improved rail production techniques provide new options for the rail user. Steelmaking improvements offer tighter composition control, lower oxide and sulphide counts, greater control of segregates and freedom from hydrogen problem s. New ultrasonic, laser and eddy current equipment gives printout information on surf ace flatness, straightness and internal condition. These have come along at a time when dramatic changes have occurred on the rail heat treatment scene. Rails can now be deep hardened on or offline in ways which should eventually result in a complete rewrite of the world's specifications. Rails of simple composition can be produced in the hardness range 2801400 BHN as required. The rail user can choose the hardness within this range according to requirement without the necessity for any step changes in the process routes.It is suggested that this is the pattern f or the next decade.IntroductionRails have been the subject of very slow improvement over many years but developments gathered momentum in the early seventies. Recent improvements in quality and properties have provided dramatic increases in rail life under the more severe service situations. Rail profile grinding, lubrication and other track improvements have greatly added to expectations of even longer life. All of this, coupled to even newer mill heat treatment developments, tilt both technical and economic advantages away from tradition to the point where specifications will need to be rewritten so that railroads can take full advantage of these new products."

Jan 1, 1988

The only functional underground Coal Mine in Nigeria is located in Enugu in Anambra State. For some years now the mine has been beset with a perenial problem of flooding. This has hampered produc- tion and some time ago the mine was abandoned. Recently money and equipment were made available to reactivate the mine. Attempts are now made to increase production as it is very much below demand. However, there are problems as the mine is below the water table under some major rivers and any advance exposes men and equipment to water surge. The paper traces the different attempts made to dewater the mine and the problems encountered in producing coal in this mine.

Jan 1, 1988

By David G. Borg, John Bussey

The new AIRDEK (tm) technique for pre-splitting in surface coal mines produces highwall conditions that have greater safety with lower costs for explosives, labor, and drilling. Successful applications have been made in highwalls ranging from 20 to 100 feet or more and in blasthole diameters from 3-1/2 inches to 12 inches.

Jan 1, 1988

By Robert B. Parsons

"One of the disadvantages of the federal government's idea of ""taxation by consultation"" is that it seems to take longer to enact new legislation. The proposed new rules for taxing automobile benefits is one example. Here is a ball which has been batted around between government and the public several times and still has not come down to earth. Fasten your seatbelts, there may be more to come. IntroductionThe draft legislation released on April 13 contains the details of the government's current proposals on car expenses and benefits. They differ significantly from the last announced position. Finance Minister Wilson has indicated that the release in draft form will provide an opportunity for the Commons Standing Committee on Finance and Economic Affairs (the Blenkarn committee) and other interested persons to comment before the legislation is introduced in Parliament. Accordingly, there may yet be revisions.Notwithstanding the prospect of further changes, the proposed rules generally come into force in 1988. While taxpayers may welcome some of these changes, particularly the increase in the tax-exempt allowance, many must be frustrated that, at this late date, the rules for the current taxation year are not yet finalized."

Jan 1, 1988

By Just G. D

The results of a geostatistical analysis of geochemical data obtained from field measurements are described in the paper. Q values derived from seismic signal rise times for different travel paths in the rock masses were used in the study. Cross-hole seismic measurements made at surface and underground sites formed the basis for the work. Geostatistical estimation of average l/Q values for area of the rock were compared with geological interpretions of rock type distributions. Reasonable correlations were obtained between the two methods of rock quality estimation.

Jan 1, 1988

By Pyrih R, House A, Shangraw J, Silva AJ

Sunbeam Mining -Corporation has the inten mine with heap leach gold recovery, near spent ore indicated a relatively high ar topographical configuration, the spent across a small drainage and a lake. Du permit for spent ore disposal from th agencies, concerns about the potential contamination by the arsenic were expres conducted extensive studies to addre contamination. These studies consiste( geochemical and geotechnical parameters underlying the proposed disposal si geotechnical investigations were also hydrologic characteristics were include with the use of an IBM PC computer. :ion of opening an open pit gold Stanley, Idaho. Testing of the ?enic content. Due to the local ore was planned to be disposed :ing the process of obtaining a federal and state regulatory for surface and ground water .ed. Sunbeam Mining Corporation is the potential for arsenic of laboratory testing of both of the spent ore, and the soils te. Field hydrogeologic and -onducted. Local climatic and 1 in the analysis of these data Conclusions of studies indicated that although the seepage through the spent ore disposal would contain an elevated dissolved arsenic content, the hydrologic and geochemical characteristics of the site would prevent arsenic migration into the local ground water system. The attenuation of arsenic on soils with high clay content, and dilution after reaching the ground water table would lower the arsenic content to acceptable Concentrations.

Jan 1, 1988

For tax purposes a mining company is a New Zealand company whose principal source of income is from the business of mining, or exploring for certain specified minerals in New Zealand. New Zealand tax law distinguishes between a non-resident mining operator and a mining company, with the only major difference in tax treatment being the corporate tax rates. New Zealand mining companies are taxed at 28 per cent, whereas non-resident mining operators are taxed at 33 per cent of taxable income. These provisions also apply to the petroleum mining industry. Individuals who carry on the business of mining are also specifically defined in the Act. They are termed as 'resident mining operators'. Non-resident mining operators are non-residents of New Zealand who carry on mining ventures as a business in New Zealand. Mining ventures are defined as the exploring, searching and mining of specified minerals, including development work carried out for profits. Similar provisions apply to the petroleum mining sector. Specified minerals are defined in the Income Tax Act 1976 ('the Act') and while no useful purpose is obtained by listing them in the paper, they include a larger number of industrial and commercial minerals. The Minister of Finance is also empowered to add to the list by publishing his determination in the Gazette.

Jan 1, 1988

"This paper describes some of the methods and equipment used for fine milling of minerals, and gives particular attention to the Vibro Energy system.In addition, the paper describes a specific application in the gold mining industry. This is the 200 tpd plant built by Anglo American Corporation at the President Brand Mine in South Africa in 1985, now a division of Freegold. This plant treats a gold bearing pyrite flotation concentrate which is finely ground to 15 microns prior to cyanidation and carbon-in-pulp (CIP). l .0 INTRODUCTIONFree milling gold ores are those that yield acceptable dissolution and recovery of the gold following grinding to what can be described as normal fineness, frequently between 50% and 90% passing 74 microns.Increasingly, gold metallurgists are faced with ores that are refractory. The traditiona1 treatment route for refractory gal d ores and concentrates has been by roasting, but for environmental reasons this is becoming less acceptable, or in some areas of the world, totally unacceptable. New methods of treating refractory gold ores are being developed and applied in practice. These new methods include pressure and biological oxidation. Higher gold liberation can also be attained by increasing the fineness of grind, although with conventional systems there are economic limits to this.In flowsheet development and test programs on new deposits, a standard procedure is to establish the relationship between the grind and subsequent go 1 d extraction. The normal situation is that gold extraction increases as the ore, or concentrate, is ground finer. Typically, this relationship is as shown in Fig. l, where the incremental additional extraction is very small once an optimum, or economic, grind has been achieved. This generally app1ies whether the material is free milling or refractory. The limits to grinding are set by the type of equipment which is commonly in use, usually ball mills. These mills have the obvious advantage of high capacity, however, they are increasingly inefficient as finer grinds are required. In general, ball mills are used to reduce ore to some agreed percentage passing 74, or possibly 53 microns."

Jan 1, 1988

By David C. Yang

A packed column (or static tube) flotation system is an innovative technology which utilizes a controlled dispersion reagent scheme and a new machine. The unique aspect of the machine is its packed-bed design permitting an unlimited froth bed height with countercurrent water washing for effective processing of fine particles. In operation, the conditioned ore slurry is fed into the middle section of the column where separation processes begin. Air, introduced at the bottom of the packed column, contacts the hydrophobic particles and floats them off continuously as the feed is added, while the gangue sinks to the base of the column. The system functions efficiently because intimate particle-bubble contact is achieved by the packing design which has no moving parts and requires no ancillary air-bubble generator. Other attractive features of the packed column flotation include high throughput, low power requirements, and simple control. Results from laboratory and pilot plant tests of this system show remarkable improvements over current industrial practices on a wide variety of ores and coals.

Jan 1, 1988

By C. J. Hall

I would like to congratulate Professor Gershon on an idea that is obviously valuable and is certainly new to me. It has, however, to be further developed, in that one can get fallacious results by limiting oneself to positional weights. In the example problem, the positional weight of one block was 8.6 (the 8.0 value in the paper was incorrect) for 36 units in the cone, for a mean block value of 0.239. The positional weight of the second block was 4.4 for 15 units, for a mean block value of 0.293. Surely one would expect the second block to be rated higher. Additionally, the time value of money adjustment cannot be determined by depth, because the time that a block is mined is determined by the mining sequence, not depth. Figure 1 shows a slightly altered version of Professor Gershon's pit. The overall value of the pit is the same, as are the total values under each of his blocks. The values in the right-hand cone have been reversed top to bottom, and the values in the rest of the pit adjusted to keep the central cone total unchanged. All values have been multiplied by 10. Figure 2 shows the sequence of mining, at three blocks per year, for Professor Gershon's pit, and Fig. 3, the sequence for a pit under the other block. Table 1 shows the value and discounted value (15%) of Professor Gershon's pit, and Table 2 shows similar values for the second pit. It is apparent that the second pit schedule is more valuable than the first.

Jan 1, 1988

By J. A. Herbst, C Lo. Y, Z. Rogovin

The identification and quantification of incipient overload conditions in mills have recently been found to be very significant in the design of tumbling grinding mills. To investigate these phenomena, a series of experiments was conducted in a Plexiglas mill operated in both dry and wet modes. For on-stream measurement of the mill charge weight, volumetric filling, dynamic angle of repose, and mill power, an electronic system was developed. The mill was filled to various levels with 19.1-mm (3/4-in.) ceramic balls as grinding media. As feed material, grindable limestone or 3.2-mm (1/8-in.) nongrinding ceramic balls were fed at various steady-state rates to determine the incipient overload conditions. The prediction of overload has apparently been reduced to predicting the feed rate that results in 50% mill filling.

Jan 1, 1988

By J. A. Herbst, J. E. Bohrer, Y. C. Lo

A systematic approach has been developed to analyze a phosphate grinding circuit with a view toward determining promising alternatives for increasing mill capacity. This analysis was carried out and capacity increases were predicted in the context of detailed population balance models developed for the plant ball mills and classifier systems. Model development and verification was performed using data obtained in a series of batch tests and two plant test campaigns. The effects of feed rate, percent solids, ball size, and mill material filling, etc., on grinding were investigated in the laboratory and plant. Residence time distribution tests were also performed to determine the transport behavior in the mill. The population balance models were found to provide accurate predictions of full-scale grinding circuit performance. Based on the findings of this study, additional capacity in excess of 25% was predicted for these ball milling circuits by a proper combination of ball size change, mill dilution, and adopting screen classification in place of hydro-cyclones. These predictions have been confirmed by plant tests in which the recommended operating changes have been implemented. Understanding the effects of operating variables on breakage kinetics and the interplay between kinetics, transport, and classification has contributed significantly to increasing the mill capacity.

Jan 1, 1988

By Pinghui J

The paper describes the detailed hydrogeological studies carried out prior to the sinking of twin shafts at British Coal's new mine at Asfordby, Leicestershire, UK. The test methods for assessing potential groundwater inflows to the shafts are discussed and details are given of the ground freezing scheme employed through the major aquifer zone in the Sherwood Sandstone at a depth of 375 metres. During shaft sinking pressure recovery tests were carried out to further assess potential inflows and the results are compared with those from the surface tests prior to sinking.

Jan 1, 1988

By A. Piche, J. Nantel

"This paper describes the recent developments in Canada toward the establishment of a Canadian Centre for Mining Automation and Robotics, at McGill University and École Polytechnique in Montreal. The role of the Mining Association of Canada (MA C) and of the National Advisory Committee on Mining Automation will also be reviewed. IntroductionIn order to remain competitive, the mining industry must increase its productivity and reduce its costs. In the last two decades, this objective has been achieved through mechanization. From now on, any further improvement in productivity will be gained through increasingly more automated mining equipment.Recent international developments following the Versailles Economic Summit in June 1982, having given rise in Canada, to a renewed interest in applications of robotics and automation to mining.The mineral industry in Canada is at a crossroads. Competition in emerging from everywhere: lower grade ore bodies, increasing distances between viable mines and markets, third world massive production of certain commodities, substitution of "" space age"" materials (ceramics, plastics, composites, etc.) for metals.On the positive side, it is generally believed that present mineral commodities, i.e. base metal, gold, iron, industrial mineral s, etc ., will continue to be in high demand for centuries to come despite substitution. New applications for conventional metals will be found and the enhancement of certain properties of these conventional metals mean continued demand. For some mineral commodities, there will never exist an y substitute."

Jan 1, 1988

By Rudolf Keller

"EMEC Consultants is developing a process to extract oxygen, aluminum and silicon from lunar anorthositic soil. The process will provide oxygen in space for propulsion, aluminum as a structural material, and possibly silicon for the construction of solar cells.The evolution of the process concept in the course of our present NASA-sponsored SBIR effort is discussed. A molten salt electrolysis producing aluminum and oxygen is the central step; inert anode technology is to be employed. Silicon will be produced by reducing the anorthite, CaAI2Si20S' with aluminum. In a steady-state operation, all components of the ore added have to be removed from the process, and the removal of calcium is a major topic of our experimental studies.Utilization of Lunar ResourcesUtilization of lunar resources may play an essential role in the exploration of the solar system and the conquest of space. High costs are involved in overcoming Earth's gravity to supply missions in space. Even at a low projected cost of $ 300 for transporting a pound of payload into Earth orbit -- today's costs are many times higher -- it appears attractive to use resources in space to produce needed materials. Processing of lunar resources on the lunar surface is an obvious possibility.Oxygen is a product of major interest. It is required for support of human life in space. Even greater quantities may be needed for propulsion, to conduct further missions into space. To satisfy this demand for oxygen through lunar processing requires a quite different solution than to supply oxygen on Earth, where oxygen gas is abundant and easy to extract from air or water. On the lunar surface, solid oxide materials have to be used. Hydrogen reduction of ilmenite and subsequent electrolysis of the resulting water is being studied [1]. Other suggestions include fluorination of lunar soil [2], reduction with lithium and electrolytic decomposition of the resulting lithium oxide [3], and aqueous HF leaching [4]."

Jan 1, 1988

By S. Chander, A. Briceno

The properties of surface films on pyrite have been studied through electrochemical techniques of cyclic voltammetry and AC impedance, measurements. The characteristics of the surface films depend on the conditions of oxidation and the source of pyrite. At potentials near 0.0 V, some pyrites have large values of polarization resistance, showing a certain degree of passivity. Some pyrites show more passivation than others, however. On oxidation, meta- stable phases of Fe(OH)2 and Fe(OH)3 form that transform to more stable phases on aging. The growth of surface films near the corrosion potential of pyrite follows a linear kinetics that is attributed to a chemical (or an electrochemical) reaction as the rate determining step. The surface film is considered to be a hydroxide or an oxide because it is hydrophilic. This study has also demonstrated that AC impedance ,measurements can be used to study the growth characteristics of films at mineral/solution interfaces.

Jan 1, 1988

By Robert B. Parsons

"It is generally felt that flow-through shares face a bleak future under the set of tax rules proposed in the federal government's tax reform white paper. Industry and government circles are beginning to give thought to alternatives to flow through as a mechanism for facilitating equity financing in the exploration industry. Despite suggestions that grants and tax credits may someday be on the table, industry is sticking to its position that there is no substitute for flow-through. Alternatives toFlow-throughProposals in the federal government's tax reform white paper have cast significant doubt on the ability of the mining industry to raise risk capital after 1989by way of flow-through shares. There is serious concern that introduction of the ""cumulative net investment loss"" (CNIL) rules, the phase-out of the mining explorati0! 1 depletion allowance (MEDA), and the Increased capital gains inclusion (750/0 versus 50%, at present) will make the economics of flow-through so unattractive after 1989 that these shares will hold little appeal to most investors. The question might be raised, then, as to what alternatives exist by way of tax or other government assistance that could help the exploration sector.The purpose of this paper is to survey the types of government incentives that could be of some value to explorationists and to the mining industry in general. For the past several years, flow-through has been in the spotlight insofar as incentives to the exploration industry are concerned. Other potentially useful and attractive incentives have been partially hidden in the shadow of flow-through. These incentives, in certain circumstances, can be of considerable benefit, and should not be ignored."

Jan 1, 1988

By Murray G

This paper outlines the processes involved in acid generation from sulphides and the key factors in identifying and predicting time dependent changes in the nature of acid mine drainage (AMD). The initial characteristics of mine water; whether drainage from exposed mining faces, runoff and seepage from waste dumps or seepage from process tailings; do not necessarily reflect the long term potential for AMD. The ultimate quality of mine drainage is a function of the interaction of many chemical, physical, biological and engineering (operational) factors. Techniques are available that can predict the qualitative nature of acid generation and mine drainage quality but accurate quantitative predictions are essentially impossible at the present time. As more and more mining operations exploit sulphide ore, the AMD and acid waste issue will become a. far greater concern. The significance of time dependent factors in the production of acid mine drainage-.is not just restricted to particuL.ar mine sites but needs to be recognised by the mining industry as a whole.

Jan 1, 1988