Search Documents

By Kostas Fytas

A computer package has been developed which is capable of evaluating alternative production schedules (long and short range) of an open pit mine once the ultimate pit limits have been defined. The model user can choose the best alternative according to cash flow considerations and the particular mining conditions. The package involves a combination of simulation for long range production scheduling and linear programming for short range scheduling. The simulation model based on an iterative technique, maximizes the profits within each long scheduling period (eg. year or sixth month period), and at the same time defers stripping as long as possible. A minimum exposed ore quantity is kept at the beginning of each mining period. The final long range schedule satisfies a set of constraints for each period, mainly ore quality and quantity constraints for ore and waste. An interactive smoothing procedure at the end of each period results in a schedule that is feasible in terms of mining practice. Finally a cash flow analysis model carries out cash flow calculations so that the user can select the best alternative. The linear programming model, based on a certain number of shovel regions, defined interactively by the model user, calculates the optimum production schedule for each short period under consideration, so that a set of constraints is satisfied.

Jan 1, 1986

By Subhash Bhagwat

The definition of high sulfur coal varies from plant to plant and is subject to changes over time as the environmental regulations change. In plants constructed after September 1978 hardly any domestic coal can currently be burned without the use of Flue Gas Desulfurization (FGD) because a 70 percent reduction in potential S02 emission is mandatory even when the potential emission is less than 0.6 lbs. S02/106 Btu heat input. On the other hand older power plants may in many cases be legally emitting up to 6 lbs. S02/106 Btu or more under some State Implementation Plans (SIP). The Clean Air Act requires, however, that in the long run all stationary sources of S02 pollution must abide by the ceiling of 1.2 lbs S02/10 Btu heat input.. Coals with a potential to exceed this limit must, therefore, be considered as high sulfur coals. Such a definition would be unrealistic because many SIP's aim at an emission level of 1.8 to 2.0 lbs. SO2/106 Btu for existing plants and a stricter limit does not appear to be enforceable in the next 5 to 10 years. As a result, coals with an emission potential of greater than 2.0 lbs of S02 per 10 Btu heat input are considered high sulfur coals for the purpose of this investigation. Based on this definition and the 1984 actual consumption of coals by U.S. electric utilities (table 1) only 7 out of the 24 coal producing states could be categorized as low sulfur states. The actual S02 pollution, however, depends on total tonnage of a type of coal as well as the sulfur content of the coal. Table 1 also indicates that only 6 states--Kentucky, Illinois, West Virginia, Ohio, Pennsylvania and Indiana-account for nearly 77 percent of S02 pollution potential in the United States. These 6 states have therefore been chosen for this investigation.

Jan 1, 1986

By R. E. Hucko

The goal of the U.S. Department of Energy (DOE) coal preparation R&D program is to develop technology to reduce the ash and sulfur contents of United States coals to levels such that the resultant product can be formulated into a high- quality solid or slurry fuel that could replace oil or natural gas in both new and retrofit applications. The Coal Preparation program is implemented by the Pittsburgh Energy Technology Center (PETC) and is conducted both in-house and by a cross section of industrial organizations, universities, and national laboratories.

Jan 1, 1986

Design a model health and safety program which, when implemented, can improve mine safety by reducing occupational injuries and accidents. Approach The Bureau of Mines developed a model program which identifies the elements essential to the effectiveness of health and safety programs designed for mining operations, and is readily adaptable to all types of sizes of mines. The model program primarily provides training on loss control and accident investigation and technical assistance with health and safety problems. In order to assess the effectiveness of the program, it was tested at both a coal and gold mining operation. Monthly statistics were generated to reflect the number of occupational injuries and accidents, and the severity of injuries (as measured by the number of work days lost during recovery). Observations were made of employees performing a large number of randomly selected jobs in order to estimate. the proportion of the workforce that was working in the presence of one or more of three types of safety deficiencies: Type A-individual job performance deficiencies which could be corrected by the employee alone I e.g., an employee is seen not wearing a seatbelt.

Jan 1, 1986

By W. J. Adamson

Strategic Data Planning (SDP) is an emerging technique for the analysis and design of information systems. This paper describes the use of strategic data planning in the formulation of a complete integrated set of mining technical systems for the Koolan Island iron ore mine. Applications covered include hydrogeology, geology, mine planning, surveying, quality control, laboratory and mine production recording. Koolan Island is 13 kilometres long and 5.5 kilometres wide at its widest point. Its sole industry is an open pit iron ore mine of 3 million tonnes annual capacity, owned and operated by BHP Minerals. Some of the production is used by BHP Steel International, but most is exported. The orebody is steeply dipping and is mined bench by bench. Outturn grades for run-of-mine product are iron 66.5%, silica 3.0%, alumina 1.0%. Computer systems are run on Data General equipment, currently an MV10000. Computer applications, which are shared across mine sites, are developed and maintained by BHP Information Systems in BHP's Melbourne Office.

Jan 1, 1986

Pajingo Gold Mine Pty. Ltd. is a subsidiary of its United States of America parent the Battle Mountain Gold Company. Battle Mountain Gold Company was created in August 1985 as a spin-off of the United States of America Pennzoil Company's gold interests.Pajingo Gold Mine Pty. Ltd. currently has its headquarters and base for operations located in Townsville, Queensland. The Company's main current activities are the exploration and evaluation of the Pajingo Gold Property situated some 50 kilometres south-east of Charters Towers and in the northern Drummond Basin.The discovery of the Pajingo gold mineralisation by the Company was the indirect result of a regional program established to evaluate Carboniferous age volcanic plugs in north Queensland for gold mineralisation.

Jan 1, 1986

By Jeffrey Y. Foley

In 1980, the Bureau of Mines investigated the northern Darby Mountains on the Seward Peninsula, AK, for radioactive mineral deposits. Uranium is concentrated in silicified shear zones in biotite quartz monzonite of the Darby pluton. The shear zones are best exposed in steep, narrow, avalanche gullies; they are characterized by radiometric anomalies and by uranium and thorium geochemical anomalies. Radiometric and geochemical anomalies are also found over altered biotite quartz monzonite where there are no visible shear zones. The radiometric and uranium anomalies are often spatially, but apparently not genetically, associated with alkaline mafic and felsic dikes. Similar geochemical and radiometric anomalies over discolored altered zones and geochemical anomalies in sediments downstream from the altered zones indicate that additional areas may also be favorable targets for uranium deposits. Analyses of panned, heavy mineral concentrates show no significant concentrations of uranium or thorium in resistant heavy minerals. This indicates that radioactive elements in the Darby pluton are concentrated in soluble, nonresistant minerals that may constitute a recoverable uranium resource.

Jan 1, 1986

By B. Stimpson, K. Kosar, K. Barron

"A number of high wall failures have occurred in some of the Alberta coal strip mines of a type called by the authors ""Multiple block plane shear slope failure "". They cause rapid deterioration of the dragline bench, reduced productivity and maintenance costs.The failures are invariably associated with the presence of almost horizontal (± 5 degrees) bentonitic clay bands in the overburden, often immediately above the coal seam, and regress behind the slope as a series of tension cracks which isolate detached blocks. As many as 17 sets of cracks have been observed, at lateral distances in excess of five times the slope height from the toe.The theory of this mode of failure is presented and a limiting equilibrium computer program which will produce deterministic or probabilistic (Monte Carlo) solutions is briefly described. A case history of one such failure is documented. It is shown that the extent of the regressive failure is exceedingly sensitive to the water table elevation, leading to the conclusion that drainage, if practical, represents the best control strategy. IntroductionA number of high wall slope failures are occurring in some of the coal strip mines in Alberta of a type called by the authors ""Multiple block plane shear slope failure""(I). These failures cause a rapid deterioration of the bench from which the dragline operates, reduced productivity, and necessitate conregresses into the slope as a series of tension cracks and detached blocks. As many as 17 prominent cracks or crack zones have been observed, the last being in excess of five times the slope height distant from the toe.The block between each pair of cracks must be at limiting equilibrium, i.e. the factor of safety equals one. This condition can be used to determine the locations of the cracks which develop in sequence behind the face."

Jan 1, 1986

By Arel B. McMahan

The U.S. Bureau of Mines investigated 21 mines, prospects, and mineralized sites in and adjacent to a 38,713-acre portion of the 255,058-acre Kingston Range Wilderness Study Area in 1983. The study area is 35 miles north of Baker, CA in the Mojave Desert. Mineral deposits in and adjacent to the study area are in altered carbonate rocks intruded by diabase sills near monzonite porphyry contacts. Monzonite porphyry forms the core of the Kingston Range and underlies about 70 percent of the study area. Sedimentary carbonate rocks are exposed in bands on the north and east boundaries and as isolated roof pendants in the southeastern portion of the study area.

Jan 1, 1986

An enormous capital outlay is required to bring a new deep level (¦ 4 000 m deep) Witwatersrand gold mine into production. In addition, future mining methods must cater for rapidly rising working costs of which labour costs make up the largest portion. South African mining engineers are therefore being forced to challenge accepted design and valuation principles when planning these high risk ventures. New mining methods must be sought to satisfy the ever increasing need for productivity improvement. The technological problems posed by such changes cover a wide range of disciplines. Aspects of shaft design and configuration, besides being examined in the light of productivity, must also consider the rock mechanics implications at depth. Mining methods must anticipate and prepare for extremely hostile conditions due to seis- micity and virgin rock temperatures.

Jan 1, 1986

By Dermot Winters

The Surface Mining Control and Reclamation Act (SMCRA, or the Act) was enacted on August 3, 1977. The Act was written, in part, to put an end to uneven environmental standards and to establish minimum national standards. Certainly, one of the motivating factors for passage of the Act was the success of the Federal Coal Mining Health and Safety Act of 1969 in reducing deaths and injuries in the coal industry nationwide. Section 516 (b) (1) of the Act requires *that subsidence be prevented from causing material damage to the extent technologically and economically feasible except in those instances where the mining technology requires planned subsidence in a predictable and controlled manner. Section 516 (c) of the Act authorizes the regulatory authority to suspend underground mining if there is imminent danger to inhabitants of urbanized areas, cities, towns, and communities. On December 13, 1977, the interim program, which applies a portion of the performance standards of the Act, was promulgated. Then on September 18, 1978, the proposed permanent program was published for public comment. Finally, on March 13, 1979, the final permanent program was promulgated and the States were given a period of time to submit their programs for approval.

Jan 1, 1986

By David A. Benjamin

At the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied prospects, claims, and mineralized sites in a 43,053-acre portion of the 51,262-acre Desatoya Mountains Wilderness Study Area (NV-030-l10) in 1985. The study area, located 50 miles east of Fallon, NV, is underlain by alluvial deposits of Quaternary age and volcanic and volcanic-derived sedimentary rock of Tertiary age. No mines or recent exploration activity were identified within the area studied. The Gold Basin area, located 1/2 mile to the south has produced 982 ounces of gold and 10,086 ounces of silver. The Cold Springs area, located 1/2 mile to the west, has recently been explored for gold-silver. Mineralization at these two areas apparently did not extend into the study area, but future mining at these areas would likely impact it.

Jan 1, 1986

By Y. G. Zhang

Interactive Dynamic Optimization Method (IDOM) will be presented in this paper. IDOM combines inventory theory, dynamic programming, computer simulation and interactive technique to formulate a production schedule for open-pit mines. This new method has been successfully used in metal mines of China for years.

Jan 1, 1986

By Marianne Snedeker

In September 1985 we published a questionnaire asking about the content of MINING ENGINEERING and about your interests. By Dec. 10, our cutoff date, we had 430 responses, representing about 1.5% of the 28,238 people who received the September issue of ME. In the data that follow the tabulation and percentages are based on the number of individuals who responded to the particular question. About ME Through responses to the questionnaire, we were hoping to learn more about you, your interests, and how the magazine could better serve you. Those of you who responded told us something positive - you look at or read the magazine. Of the 430 respondents, 428 or 99.5% indicated that they had read or looked through the July and/or August issues. Those of you who refer to the magazine once are 207 or 48.5%. Those of you who refer to the magazine two or three times are 193 or 45.2%. Those of you who refer to the magazine four or more times are 27 or 6.3%. How much time do you spend reading the magazine? Of those responding to this question: 64 spent up to 1/2 hr 15.0% 224 spent up to 1 hr 52.6% 115 spent up to 1-2 hr 27.0% 23 spent more than 2 hr 5.4% In an informal survey among our staff, we determined that most people spend 1/2 to 1 hr reading magazines to which they subscribe at home. Does that match your experience? Many of you, 335 or 79%, clip your magazine for further reference. Also, many of you, 313 or 73.6%, do not pass your copy on to another reader, indicating that you are clipping it or receiving the magazine at home. Those magazines that are passed on reach: 1 person 3 0.7% 2 people 64 15.1% 3-5 people 34 8.0% 5 or more 11 2.6% Answers to what portions of the magazine you find useful indicated that the top three were Industry Newswatch, feature articles and Technical Papers; see Table 1. The "other" category included advertising - display, classified, Employment, and Professional Services - Washington Survey, New Products, Free Literature, book reviews, technology news, and Coming Events and Short Courses. We asked your appraisal of the technical level of the magazine. Of those responding, 39 or 9.1% indicated that it is too technical, 55 or 12.8% indicated it is not technical enough, and 335 or 78.1% judged it to have the correct technical level. In response to the question about whether you like to read an occasional feature that is not technically oriented, 21 or 5.1% said no, but an overwhelming 94.9% (393) said yes. Of the specific

Jan 1, 1986

By Alan J. Fejes

As part of its mine subsidence research program, the Bureau of Mines and the American Electric Power Co. cooperated on a study, conducted at the Price River Coal Co. No. 3 Mine, directed toward developing the capability to estimate the surface subsidence resulting from longwall mining in a geologic, topographic, and mining environment common to coalfields in the Western United States. Subsidence was monitored at the No. 3 Mine over two adjacent longwall panels. The subsidence study area was reduced when the two planned panels were reduced in length because of equipment failure and a mine fire. Subsidence was measured for 21 months. Subsidence continued for 6 months after mining had been completed. A maximum of 2.2 ft of subsidence occurred over the two longwall panels mined at an overburden depth ranging from 300 to 1,500 ft.

Jan 1, 1986

Reverse circulation (R.C.) drilling or the dual tube method as it is quite commonly known, has a unique place in conventional mineral drilling. It can be classified half-way between open hole drilling at the lower end of the scale and diamond drilling at the upper end. The system basically consists of two tubes, one inside the other, with compressed air flowing between the inner and outer tubes. Sample cuttings return up the inner tube through the head of the rig and via a hose to a cyclone where the sample is collected. This system means that the cuttings are free of contamination as they are at no time in contact with the outside formation of the hole.Reverse circulation drilling is divided into two areas: R.C. Roller and Blade for softer formations; and R.C. Percussion for harder formations.

Jan 1, 1986

By E. C. Watkins

The fiber glass industry is an industry that. hopefully is still in its infancy and far from a mature business. Fiber glass, as will be discussed in this paper, deals with continuous strand glass as used in the textile laminate and reinforced plastics industries. More specifically, we are speaking of glass used for printed circuit boards, tapes, paper, cloth, pipes, tanks, boats, recreational equipment, roofing shingles, and automotive applications. Compared to the flat, container and decorative glass industries, we are very young. The early patents on fiber glass applications were issued in the 1930's. The type of glass most commonly used in the world and that discussed in this paper is designated as "E" glass. This is a boro-silicate type glass having specific chemical and electrical resistance and low thermal expansion properties.

Jan 1, 1986

By K. L. Ludeke, A. D. Day

For many reasons, it appears that deep rooted, perennial shrubs offer potential for improved stabilization and provide maintenance free vegetative cover to harsh sites where perennial grasses have not been successful. The major objective was to select various shrub species of arid plants for initial soil stabilization of disturbed mining areas. The very fact that a drought-adapted shrub has a massive root system that can use moisture from a greater volume of mineral waste soil materials suggests that arid environment disturbed soils may be vegetatively stabilized using desirable forage shrubs. A secondary effort is underway to assemble information and plant materials of promising species from many arid regions of the world for reclamation of mined lands. Surprisingly, many of the better plants for arid sites are quite high in protein content. With proper management, breeding, and selection, they may prove to be very desirable livestock feed when mined lands are used in range land areas. Advancements in arid land solid waste stabilization hold favorable promise for many industries that mine and mill in arid regions for effective reclamation of disturbed areas. Particularly exciting is the possibility of establishment of high density maintenance free vegetative cover of climax vegetation that reclaims the disturbed area back to its original land use. Due to high shrub productivity, stabilization potential, nutritional quality, and reclamation success, greater use should be made of shrubs in disturbed land reclamation associated with mining and milling operations in harsh aril environments.

Jan 1, 1986

By G. M. (Frits) Swinkels

The Apex property, mined in the early Twentieth Century for direct shipping copper, also contains gallium and germanium in iron oxide minerals. In 1982, Musto Explorations Limited began an exploration program to define reserves. A metallurgical process was developed, and a production decision was reached in late 1983. This text describes the process development and design. The Apex mine, located near St. George in Southwestern Utah is owned by St. George Mining Corporation, a subsidiary of Musto Explorations of Vancouver, B.C. Musto acquired the property in early 1982. A pilot plant was operated by Hazen Research, Inc., Golden, CO later in 1982. In late 1983 sufficient information had been developed for St. George to proceed with the project. The final process design was prepared by G. M. Swinkels of Vancouver, consultant to Musto, and Hazen Research. Process engineering was done by Hazen Research, and St. George acted as its own contractor. Commissioning of the plant began in October 1985.

Jan 1, 1986

By Douglas J. Harvey, Chi-Mou Ni

"This paper presents an analysis technique for the solidification of metal castings. This method, based on a modified finite difference scheme with an irregular mesh, is capable of dealing with the complex geometries of castings. The nonlinearities in material properties of specific heat and thermal conductivity, arising from the phase change during solidification, are accounted for in the step-by-step calculations. Two solidification problems are solved with this analysis technique and the calculated results compare satisfactorily with experimental data. IntroductionCasting process design engineers are often faced with the difficult problem of designing castings to be produced porosity-free. Since the solidification of metal is affected by many interacting variables such as the thermal conductivity, density, and specific heat of both the molten metal and the mold, it is easily seen why this is a difficult task.Typically, casting tooling design is an intuitive process which builds on past successful methods. After processing equipment is constructed, trial castings are made and examined for dimensions and integrity. Changes in the tooling are generally required to improve casting soundness or to reduce cycle time. In the permanent mold process, tooling is complex and difficult to alter after initial construction. The water-cooled steel molds are part of the complete automated system. Associated holding furnaces, pouring ladles, casting conveyers, and utility connections all make other than minor adjustments a costly and time consuming task. An analytical method for using the principles of heat transfer for predicting solidification patterns would be of great value in the permanent mold process by minimizing costly changes."

Jan 1, 1986