Search Documents

By K. H. Nimerick

Froth flotation of coal is growing in importance and complexity. Some of the reasons for these changes follow. 1) A need exists for energy resource conservation. 2) Preparation plants are processing widely varying coal -- deep seam, strip and stockpiled either separately or as blends. 3) More fines are being generated because more mines are using automatic mining equipment. 4) It is more practical and economical to remove ash and sulfur at the preparation plant than during utilization.

Jan 1, 1982

By Mark Gershon

This paper describes a linear programming (LP) application that schedules mining operations in an optimal manner. The model is developed such that it can be applied to a broad spectrum of mining activities. While linear programming has been applied to mine scheduling in the past, the models have been either site-specific or they have only optimized one aspect of mine operations without regard to others. The Mine Scheduling Optimization (MSO) concept makes use of a mathematical model to: (1) Determine the optimal operation of a mine, from mine to plant to market. (2) Account for mine-plant-market interfaces. (3) Optimize operations over the life of the mine. (4) Accomplish long, intermediate, and short range planning.

Jan 1, 1982

To identify the most successful methods now in use for controlling respirable dust in longwall mines using double-drum shearers. Approach Conduct dust surveys at six longwall mining sections that use double-drum shearers and are regularly in compliance with the Federal Respirable Dust Standard, to identify effective dust control techniques. The selection of mine sites was based on recommendations provided by the Mine Safety and Health Administration. Instantaneous and short-term gravimetric instrumentation make it possible to isolate longwall dust sources and to determine the effectiveness of dust control techniques. (These procedures were developed by the Bureau of Mines, and are described in detail in Technology News Bulletins 134 and 135.) Production levels, and seam heights at each of the six longwall sections were: 53", 700 tps; 60", 800 tps; 72", 1000 tps; 79", 1500 tps; 84", 2000 tps; 96", 1500 tps. Survey Results Three effective dust control techniques were identified. 1. Shearer Operators on Intake Side of Lead Drum-At all mines surveyed, an important factor in controlling dust exposures at the shearer is the use of a cut ting sequence that allows the shearer operators to work most of the time on the intake air side of the lead drum. Dust profiles, like those plotted from data at two mines (see the graphs), show the large gradient in dust concentrations that can

Jan 1, 1982

By Michael T. Nigbor

The Bureau of Mines assisted the Rocky Mountain Energy Co. in a pilot-scale in situ leaching experiment at Casper, Wyo., to determine if sulfuric acid can be used as a cost-effective alternative lixiviant (leachant) for uranium in situ leaching. This experiment, which lasted more than 2 years, is the first fully documented pilot-scale operation in which the leaching-restoration cycle was completed using sulfuric acid instead of the more common carbonate-bicarbonate leachant This report describes activities at the experimental site, presents extensive geochemical data from startup to site restoration, compares laboratory and field experiments, and discusses the environmental aspects of acid leaching. The data showed that sulfuric acid is apparently an effective leaching solution. Three to five grams of acid per liter of ground water resulted in a production solution grade of 80 to 100 ppm uranium. Restoration was successful, but required extended flushing. The pH was the last chemical parameterto return to baseline, requiring about 350 days. This was longer than was predicted in laboratory simulations. The data also showed that mobilization of toxic elements such as selenium, arsenic, radium, thorium, and molybdenum stayed within reasonable limits and quickly fell back to preleach concentrations during restoration.

Jan 1, 1982

By Alten F. Grandt

What is prime farmland? Can such land, once it has been surface mined for coal, be restored so that it will produce corn, soybeans, wheat, and alfalfa? What methods or practices are necessary to bring about restoration within a reasonable time so that crop yields will be equivalent to or higher than those of unmined prime farmland under high levels of management? These questions concerned land use researchers in Illinois as early as 1948 when the Illinois Agricultural Experiment Station experimented with growing cultivated crops on surface mined land in St. Clair County (Grandt, 1949). This research was done almost thirty years before requirements of Public Law 95-87 were passed by the US Congress and signed August 3, 1977.

Jan 1, 1982

By M. R. Moharam

The well-known formulae of screening efficiency and circulating load calculations in closed crushing circuits were exploited to achieve graphical estimation of these parameters. Three basic charts were proposed and constructed. The first one is for the regular closed circuits where the new feed goes to the crusher. The second is for the reverse closed circuits in which the new feed reported to the screen is free of screen undersize particles. The third chart controls the reverse circuits when they are receiving new incoming feeds containing undersize material. Compound circuits were also reanalyzed and a concept of equivalent simple circuit was introduced to enable graphical manipulation of these complex circuits with the help of the aforementioned charts

Jan 1, 1982

By Karl A. Olsson

The Glenharold Mine is a surface mine operated by Consolidation Coal Company. The mine is located approximately 90 kilometers (55 miles) northwest of Bismarck, and 3 kilometers (2 miles) southeast of Stanton in west central North Dakota. Glenharold has a nominal design capacity of 3.0 million metric tons per year (3.3 million short tons per year). With the exception of local coal sales, this production supplies fuel for Basin Electric's Leland Olds generating station, a mine mouth power plant. The mine has 175 hourly and 50 salary employees. The Glenharold reserve extends over 210 square kilometers (80 square miles). The mining area is on a dissected plateau between the broad flat Missouri River flood plain to the north and the gently rolling uplands to the south. Erosion by intermittently flowing streams has produced many narrow, steep-walled, drainage ways. Mining begins at the 6 meter (20 foot) cover line and continues to the economic recovery line.

Jan 1, 1982

By Lynn C. Fister

"Coal is rapidly becoming a major alternative to oil. According to the World Coal Study Final Report, total world coal trade could approach one billion tons annually by the year 2000. To facilitate the increased production and export market potential of the coal producing countries, advancements must be made to improve the transportation systems. Coal slurry pipeline systems could play a significant role in achieving these market forecasts.There are three major components to a coal slurry system the preparation plant, the pipeline and the dewatering plant. The experience and expertise gained from the Consolidation Coal Company system in Ohio, the Black Mesa system in Arizona and ETSI's Coal Evaluation Plant demonstrate that slurry pipeline technology is proven and available to meet the coal transport challenge.The costs of transporting coal by slurry pipeline can offer significant savings, as about 70 per cent of its costs are fixed. The reverse is true for railroads, where 75 to 80 per cent of the costs vary with inflation. All forms of transport-rail, barge and pipeline-will be required to move the massive volumes of coal. Coal slurry systems can provide a viable transport alternative.IntroductionThe importance of coal as a major alternative to oil is now well known and accepted throughout the world. Increasing oil prices over the last eight years have had a serious effect on national economics, particularly in those countries that are heavily dependent on oil. Coal can replace oil as the principal fuel source which could support world economic growth over the next two decades. This is the main conclusion of the World Coal Study (WOCOL) Final Report, published in May 1980.The product of that report was a result of considerable deliberation by key industry leader s and energy experts. The underlying message of the World Coal Study is that our energy and economic problems can be faced with confidence if coal use doubles by the early 1990s and triples by 2000, and if steam coal trade expand s considerably."

Jan 1, 1982

By Benjamin W. Haynes

Cement kiln dust (CKD) produced in the contiguous United States and Hawaii was characterized as part of the Bureau of Mines' program in minerals environmental technology. The mineralogical and chemical composition was determined for 113 CKD samples from 102 plants that normally send CKD waste to landfill. Characterization included the determination of 28 elements, 7 anion species, carbon dioxide, noncarbonate carbon, and chemically bound water. Mercury was determined in 15 samples. Interelement correlation coefficients were determined for 23 elements, 5 anions, CO2, noncarbonate carbon, and chemically bound water. To assess the hazardous waste potential of CKD, the U.S. Environmental Protection Agency Extraction Procedure (EP) toxicity test was performed on all 113 CKD samples. All but one sample were in compliance with the test; the noncomplying sample slightly exceeded the EP toxicity test criterion for lead.

Jan 1, 1982

By C. B. Henderson

The development of slurries of coal and water as a boiler fuel replacing No. 6 fuel oil has been actively pursued at the Atlantic Research Corporation since 1976. Funding for this effort has been provided by the U.S. Department of Energy, the Electric Power Research Institute, and by corporate funds. The name ARC-COALTM has been selected for these slurries. Stable coal-water slurries with bone-dry coal loadings between 62% and 77% have been prepared, evaluated rheologically, and successfully burned in an experimental furnace without the assistance of other fuels. The advantages and properties of these slurries, including combustion results, are reviewed. Also discussed is the pilot line used for processing barrel quantities of fuel and a pilot plant capable of processing 600 bbl/day, currently being designed.

Jan 1, 1982

By W. D. Keller

Scanning electron microscopy (SEM) accompanied by X-ray energy dispersive analysis (XES) is a useful tool in process clay mineralogy. The texture of kaolin, illustrated by SEM, gives a clue to its mode of genesis and probable industrial application. One type of kaolin, originating dominantly by weathering, has an open texture, slakes readily, and is used for filling and coating paper. Another type, in contrast, originates by diagenesis of Al-silicate sediments, and spectacularly resists slaking, thereby enabling it to maintain its bulk density and controlled size and shape of particles after crushing and moistening; this meets an important requirement for the manufacture of refractories. Ratios of elemental Al:Si that may be rapidly determined by SEM and XES yield information on the origin and purity of bauxite and bauxitic clays, and aid in quality control and processing of them. SEM of dissimilar textures of quartz, as in chert and novaculite, are evidence for geothermometry on a stratigraphic scale that is potentially useful in delimiting thermally favorable or unfavorable areas for hydrocarbon exploration, and possibly for unexposed metallic ore deposits.

Jan 1, 1982

By M. N. Brodie, John Chapman

INTRODUCTION - DEFINITION & HISTORICAL PERSPECTIVE While this symposium is concerned with comminution which, by definition, relates to all stages of size reduction of an ore body to a form suitable for mineral separation, the electrical drive aspect of the grinding section will receive most attention in contrast to the crushing, screening and materials handling elements of the process. The reason for this is that today's large mills, thirty feet diameter and upwards, present mechanical and electrical problems which require a degree of sophistication in their solution not previously required. The ability to satisfy these demands, so far as electrical technology is concerned, largely results from the development of semi-conductor devices. These can now handle typical electrical distribution power levels within remarkably s m all volumes and with high efficiency when compared with the motor-generator sets, mercury arc rectifiers, rotating amplifiers, magnetic amplifiers and vacuum tubes which were commonly used to provide speed and torque controls as recently as the early nineteen-sixties. The hardware available to the electrical engineer has changed dramatically whereby even the simplest control system formerly using hard-wired relays is now superseded by the program m able logic controller with its computer-like memory containing the sequence of operation, in other words, the software. Reverting now to the mineral process itself, it is assumed that the ore body has been mined using explosives and is delivered to the concentrating plant in its 'run of mine' form. The problem becomes one of reducing the material to a size which will permit an acceptable recovery of the mineral with the most economical use of energy. The size of 'run of mine' material will range from about minus five feet for high tonnage open pit operations to minus two feet for the smaller underground mine. The final reduction in size may range from minus ten mesh to minus two hundred mesh (exceptionally as fine as minus six hundred mesh) depending upon the concentration method and dissemination of the mineral values within the ore. There is no single circuit that satisfies all applications, but the pattern of metallurgical equipment use shown in Table 1 appears discernable from current practice, in general terms.

Jan 1, 1982

By Jorgen Elbrond, Yve Lizotte

"A mine evaluation method based on the use of a computer program that models mining with an open-ended dynamic program is presented in this paper. It is demonstrated with an example how the method is applied, how some of the decision variables are related in the particular industrial environment and how these decision variables affect the economic benefits of mining.IntroductionTwo distinguishing characteristics make mining a particular industrial environment: exhaustible resources of a given ore deposit and heterogeneousness of the ore grade spatial distribution in the ore deposit. These characteristics, inflation, uncertainty and cyclical price variations which greatly affect estimated cash flows also contribute in rendering difficult the evaluation of the economic outcome of mining at the preliminary planning stage.Decision variables and their ranges are associated with the mine plan; basically, they include choices of the mine's nominal capacity (mining and milling), the sequencing of mining through the deposit, the ranges of possible production rates and cutoff grades, and the stockpiling policies. The mine's nominal capacity must be decided at the planning stage, but this capacity choice must take into account flexibility to modify other decision variables as mining commences and uncertainty resolves.Although it is generally accepted in discounted cash flow analysis that the sequence of mining must proceed from the richest to the lowest-grade stopes (with correspondingly ajusted cutoff grades), this may not produce optimum benefits when cyclical price variations are considered.Mining rates and cutoff grades can also be adjusted to changing economic conditions, taking into account the limited resources of the ore deposit. Thus, when prices are thought to be in the trough of a cycle, production can decrease to preserve ore for expected greater future profits. When prices rise, mining rates can increase possibly even over the mine's nominal capacity. In both cases, the machinery's effectiveness shall not be-optimally utilized; this will be reflected particularly by the variations in the concentrator's metal recovery and the concentrate grade output."

Jan 1, 1982

By D. J. MacDonald

The Bureau of Mines has carried out investigations on a method for producing zirconyl sulfate solution from zircon sand, comprising (1) reacting zircon sand with molten NaOH, (2) leaching the resultant fusion frit with water to remove sodium silicate and to convert sodium zircon-ate to hydrous zirconium oxide, and (3) leaching the hydrous zirconium oxide from unreacted sand with hot, dilute H2S04 to produce crude zirconyl sulfate solution. The following conditions were found to be suitable: reacting 0.6 kg of NaOH per kilogram of zircon sand for 10 min at 600° C; leaching the frit with 3 to 4 liters of water per kilogram of solids; leaching the residue with 5.1 liters of water and 1.25 liters of 98-pct H2S04 per kilogram of original solids for 10 min at 90° C; and filtering or decanting to recover unreacted zircon sand. A preliminary cost estimate is included.

Jan 1, 1982

By F. J. Hogan

In early 1982 Atlantic Cement Company, a wholly-owned subsidiary of Newmont Mining Corp. will come on line with a new water granulating grinding facility at Sparrows Point, Maryland to produce 800, 000 tons a year of separately ground granulated blast-furnace slag. The process and product will be unique to the United States. This paper will review some initial investigations undertaken to evaluate the cementitious properties of granulated slag. The effect of slag fineness on strength development is discussed and data is presented showing a relationship between glass content and hydraulicity and grindability of slag.

Jan 1, 1982

By C. Jay Hodgson, P. J. MacGeehan

"The gold ore zones of the Campbell and Dickenson mines occur within a km-wide, 2 km-long zone of highly altered and anomalously fissile and deformed volcanic and subvolcanic intrusive rocks, cut by a series of mainly post-deformation mafic and quartz-feldspar porphyry felsic dykes.Three main periods of gold ore-forming hydrothermal activity are recognized. In the first, the mine rocks were extensively altered and gold and arsenic enriched; syn-volcanic auriferous veinlet and low-grade chemical sedimentary ores were deposited in what was a major discharge zone of a submarine hydrothermal system. The chemical sedimentary ores are closely associated spatially and temporally with domal rhyolitic extrusions. Because of its mechanical and chemical properties, this synvolcanic alteration zone became the locus of later deformation, and the site of the generation of auriferous hydrothermal solutions, perhaps by pressure solution processes at depth. These solutions deposited, synchronously with deformation and metamorphism, the second and most economically important type of ore zones in the mine: large foliation-parallel and foliation-oblique banded carbonate- 'chert' Rssure-filling veins.In the third and final mineralizing event, high-grade, pipeshaped zones of siliceous replacement-type mineralization, and quartz-arsenopyrite-gold veins, were superimposed on the previous mineralization types after most of the deformation, but before the emplacement of the late dykes. The source of heat and also possibly the fluids for the third mineralizing period may have been the dyke-forming igneous activity. The textures and mineralogy of the banded carbonate- 'chert' veins suggest a near-surface (<3 km) environment of deposition, but their relationship to the fabric of their host rocks indicates they were emplaced in an environment, presumably at considerable depth (5-10 km?), in which the rocks were undergoing intense penetrative deformation. This anomaly is unresolved."

Jan 1, 1982

By Joe L. Ratigan

INTRODUCTION Rock mechanics engineers are seldom concerned with obtaining the tensile or fracture strength of brittle rock at low mean stresses. The reason for this is two fold. Firstly, the behavior of many excavations in brittle rock is controlled by the inherent discontinuities in the rock mass. Because of the jointing and faulting, tensile strength is usually taken to be negligible. The second reason that tensile strength is seldom obtained in the laboratory is that the technology of utilizing this strength measure in design is undeveloped. Despite the fact that tensile strength of brittle rock is often ignored, there are a number of applications in rock mechanics wherein the knowledge of tensile strength is of fundamental importance. The apparent tensile strength must be known in a hydraulic fracture experiment if the state of in situ stress is to be determined from the initiation of the hydraulically induced fracture. In certain underground situations, the apparent tensile strength of intact rock beams defined by jointing or bedding planes is important in determining required rock bolting. Numerous other situations require a knowledge of apparent tensile strength including such high technology uses of underground space as geothermal energy extraction and LPG storage. Three observations are invariably made when intact rock samples are taken into the laboratory and tested to determine tensile strength. (1) The apparent tensile strength depends on the sample size (the 1 arger the specimen, the lower the tensile strength)

Jan 1, 1982

The Perth Mint receives gold and silver from various sources for evaluation and refining. The metals are received in many forms and vary widely in assay. Refining is carried out using the Miller Process and the and the resulting market quality bullion is sold in a range of weights and alloys to suit the international bullion market and public demand. INTRODUCTION The Perth Mint was established in the late nineties as a branch of the Royal Mint, London, to refine the gold from the newly established gold- fields in Western Australia. The branch was opened for business in June, 1899. After refining, the bulk of the gold was used in the manufacture of sovereigns and half-sovereigns. Nowadays, although most of the gold received comes from the W.A. goldfields, some gold is deposited by producers in other states and in Papua-New Guinea, as well as scrap and trade wastes from manufacturing jewellers and old jewellery from the general public. Silver is deposited in the form of old silverware, recoveries from-photographic processes etc. Gold or silver may be lodged at the Mint in person, through a bank or other agency or by registered post. Telegraphic advice is usually given when gold is sent by the latter, so that insurance may be effected.

Jan 1, 1982

By C. Burton Clark

The important role of the petrographic microscope in the petrology of refractories is discussed, based on 45 years of industrial experience by the author. Highlights of his career are used to illustrate improvements in equipment and techniques during the period. Two specific investigations are described which emphasize the interrelated use of the petrographic microscope with other instruments such as the x-ray diffractometer and scanning electron microscope. Emphasis is placed on the use of phase equilibrium diagrams for guidance in predicting and interpreting reactions that occur under non-equilibrium conditions in the manufacture and use of refractories.

Jan 1, 1982

US 4,185,078-In the recovery of rhenium values from an aqueous sodium molybdate solution contained in the hydrometallurgical processing of roasted molybdenite, improved results are realized by using a described extractant consisting of a quaternary ammonium compound and benzene or other highly aromatic solvent which dissolves a quaternary ammonium-rhenium complex Essentially all rhenium is recovered from the solution and the extractant can be regenerated and recycled. This patent is a continuation-in-part of US Patent No. 4,049,771, dated Sept. 20, 1977. L R. Quatrini and M.B MacInnis, assigned to GTE Sylvania Inc. Jan 22, 1980. 6 pp (423-49). Flied. 7-19-78 (926,167).

Jan 1, 1982