Search Documents

By Werner Hofmann

INTRODUCTION The attempt to interprete lung cancer incidence caused by inhaled radon decay products in items of radiation dose raises the question of the relevant dose. The various dosimetric approaches published by now are characterized by an increasing complexity in the structure of the models used. Ranging from organ doses to microdosimetric specific energy distributions in the cells at risk, a significant trend from the macroscopic to the microscopic scale can be observed. Since tumors originate preferentially in the basal cells of the lobar and segmental bronchial epithelium, these cells are regarded as the critical target for inhalation carcinogenesis. The evaluation of basal cell doses is, therefore, the main objective of lung dose assessments. Various dosimetric models have been published in the past (Altshuler, Nelson and Kuschner, 1964; Haque and Collinson, 1967; Harley and Pasternack, 1972; Hofmann, Steinhäusler and Pohl, 1979, 1980; Jacobi, 1964; Jacobi and Eisfeld, 1980; James , Greenhalge and Birchall, 1980). Due to incertainties of physical and biological parameters involved and the application of different anatomical and physiological models the claculated doses are varying up to one order of mangitude. Independent of the choice of these dosimetric models applied to the calculation of lung doses, deposition, clearance and resulting dose are affected essentially by the properties of the inhaled aerosol as well as by personal characteristics. Both the properties of the exposed individual as well as of the inhaled environmental atmosphere have to be considered in radiation protection. It is the main objective of this paper to illustrate the influence of both parameter sets on basal cell doses by varying the above parameters. PERSONAL CHARACTERISTICS Though it might be more convenient for radiation protection calculations, the biological "man" cannot be represented by a uniform standard man. In Tab. 1 these personal characteristics which cause the variability of man are listed together with the region of their effectiveness. In the following the influence of these parameters will be discussed with regard to lung dose assessments. Besides these factors the great biological variability of all anatomical and physiological parameters involved as well as pathological alterations due to lung diseases cause additional variations in lung dosimetry. [ ] Age Age can be considered as the most important personal factor influencing the anatomical structure of the lung between birth and about 15 years of life. This period is characterized not only by an enlargement of already existing respiratory units but also by structural changes. Besides these anatomical alterations deposition is strongly dependent also on respiration parameters, such as tidal volume (TV) and respiratory frequency (RF). Whereas RF decreases with progressing age in an exponential manner, TV increases significantly resulting finally in a growth of the respiratory minute volume (RMV). Also mucus clearance in the infant might be more effective than in the adult, though no reliable experimental data are available. Superposing all these age-dependent changes mean basal cell doses are higher for children by about a factor of 2 than for adults living in the same radioactive environment (Hofmann, 1981). In the adult the following alterations of respiration standards with age are reported: total lung capacity diminishes with age, functional residual capacity is unchanged or increases with age and the dead space rises slightly with age (ICRP, 1975). The influence of these lung capacities on deposition, however, can be regarded as insignificant. Due to the ageing process mucus velocities my be considerably smaller in older people. This effect can also be superposed by the simultaneous influence of ciliatoxic effects of cigarette smoke and air pollutants or other bronchial diseases. Since the lower age limit for occupational exposure is about 18 years, age can be disregarded in the uranium mining industry for the determination of radiation doses, though lung cancer induction is significantly dependent on age.

Jan 1, 1981

By Jed H. Mosgrove, Paul M. Budzak

INTRODUCTION Good mine ventilation starts at the drawing board. A coal mine will either be adequately ventilated or not, depending upon how good a job was done in the planning. Poor planning will not only result in inadequate ventilation, but may also lead to low productivity. A mine foreman cannot achieve high productivity while trying to maintain 4.2 m3/s (9000 cfm) of air at his last open crosscut. PLANNING What will provide adequate ventilation? A rule of thumb in laying out a coal mine is to provide enough entries in the main entry system to keep air velocities at 2.5 m/s (500 fpm) or less; at this rate of flow, good ventilation may be expected. The intake and return air courses of a coal mine do not improve with age. Entries will deteriorate, ribs will slough, roof will fall, and clutter will accumulate. The resistance offered to air travel will continue to increase with each passing year. Providing enough airways for the present and the future cannot be emphasized too strongly. In order to better appreciate good planning and bring it into better focus, assume a hypothetical mine has the following features: entries 1.5 m (5 ft) high and 6.1 m (20 ft) wide; one intake and one return entry; the mine development is 4.8 km (3 miles) from the intake and upcast ventilation shafts; and the ventilation requirement is 141.6 m3/s (300,000 cfm) . Air travel of 4.8 km (3 miles) into a mine and the same distance back to the fan is not unusual. However, to do so with one intake and one

Jan 1, 1981

By Creasey J. W, Huntington J. F

Faults cutting the Lithgow and Katoomba seams in some collieries of the Western Coalfield can be classified, on the basis of spatial pattern, into three principal groups: meridional swarms of closely spaced minor faults and associated joints, with throws of less than 0.5 m and with exceptional faults of up to 5 m; isolated interswarm strike-slip faults in the Lithgow seam and widely spaced strike-slip faults in swarms in the Katoomba seam; and low-angle normal faults associated with the Lidsdale-Lithgow seam split.Orientations of faults and coal cleats in the coalfield are presented on stereoplots and histograms, as a basis for an analysis of fault dynamics. The low-angle normal faults were found to have been formed only along the Lidsdale-Lithgow seam split, and before the high-angle faults. The origin of the high-angle normal faults in the meridional swarms is discussed and it is suggested that basementcover interactions must have occurred. This suggestion is supported by geophysical evidence. Low-amplitude monoclines in the coal seam, and the spacing of swarms 0.9 to 4.5 km apart, may be due to the underlying basement structure.It is clear that postextensional compressive deformation of swarms in the coalfield gave rise to shortening by minor thrust development, and probably also caused the synchronous strike-slip movement on pre-existing normal faults. There is evidence to show that isolated interswarm strike-slip faults in the Lithgow seam, and widely spaced strike-slip faults in the Katoomba seam, may have originated synchronously with such thrusts. The axis of maximum principal compression ('71) for the thrust event was inferred to be near horizontal and aligned approximately E-W. Recent rock mechanics measurements of the present day stress field indicate a similar stress configuration.

Jan 1, 1981

By D. C. Torre

Ever since the early '60's there have been efforts to develop and produce reliable continuous haulage systems capable of taking the full output of a continuous miner and transporting it, in one continuous flow, from the face to the tipple. The majority of the continuous haulage systems which have been most successful to date were placed in operation in the early '70's and were all of the bridge conveyor type, usually consisting of bridges and mobile bridge carriers attached at the inby end to the continuous miner and at the outby end to the panel conveyor itself. These successful bridge conveyor type continuous haulage systems were, and continue to be, either of the belted or chain type. Undoubtedly, the most successful belt type continuous haulage systems are those manufactured and marketed by the Long-Airdox Company. Until early 1977, the most successful chain conveyor type haulage systems were manufactured and marketed by Jeffrey Mining Machinery Division. In 1977, Long-Airdox reentered the market with a chain type system to complement its belted system. I say "reentered" because the original bridge type continuous haulage system was introduced to the coal mining industry in the early '60's by the old Long Company, a predecessor of the current Long-Airdox Company, and those original units were of the chain conveyor type.

Jan 1, 1981

By Robert Stefanko

Shortwall mining represents a compromise between the room-and-pillar and longwall systems. Figure 1 shows that the shortwall layout is very similar to that for longwall panels, the primary difference being that the shortwall is generally 150 to 200 feet wide while longwalls are 350 to 600 feet wide. The development of entries is divorced from the production of the walls with both systems. However, the depth of the web is considerably different in the shortwall system. Because a standard continuous miner is employed, a depth of 10 feet is normally mined on a single pass. This greater web thickness requires the use of a specially constructed support that can support the much longer cantilever bar that must extend over the working area. This is accomplished by not only increasing the length of the bar but also strengthening it structurally; however, the key to success lies in articulating the cantilever from the base and supporting it with a short hydraulic jack leg. This arrangement provides the additional strength required in the support. It should be apparent that a shortwall support is more costly than the type used for longwall.

Jan 1, 1981

With increasing depth of mining, geotech nical factors assume increasing importance in the design and operation of open pit coal mines. Dragline strip mines are particularly sensitive to stability conditions since the draoline is a relatively inflexible machine, particularly in relation to its limited dump- ing radius for overburden disposal. Geotechnical factors relevant to strip mine design include: 1. spoil pile stability 2. wall stability 3. floor stability 4. excavation characteristics 5. groundwater conditions A basic geotechnical investigation pro- gram for new mine feasibility studies is described. This includes: 1. terrain evaluation 2. geotechnical drilling and logging 3. geophysical logging 4. materials testing 5. seismic refraction traversing 6. groundwater studies Such a program will give an overall geotech- nical assessment of the site and highlight any areas which may require further, more detailed Investigations

Jan 1, 1981

By Eric Best

"In the past two to three years, all continuous mining machines at the Potash Corporation of Saskatchewan Mining Limited, Lanigan Division, have been changed over to a new cutting pattern using 1 -inch- and 1-3/l6-inch-diameter self-sharpening pencil bits. The bits are arranged in a cone-type pattern across the face on 2 1/2 -inch and 3-inch spacing. The result is that the ore is removed by chipping and flaking. Previously, rap-lock bits were used, with the pattern being several bits in single rows at wide spacings. The cutting action was grinding and breaking.Besides improved penetration rates and lower bit costs, there are many other advantages. The ore size is much smaller, resulting in less wear and tear on conveyors and other associated equipment. Feeder-breakers are no longer routinely set up at the head end of every extensible belt, as the banana-shaped chunks of ore that used to require breaking are no longer produced. Also, less dust is generated by the cutting heads and fewer stops are required for bit changes. Even the mill operation has been improved, as fewer fines are produced.Further improvements are still sought after, but, all in all, the new cutting pattern is considered to be a giant step forward from the old method."

Jan 1, 1981

By Steven J. Page

The increasing concern for dust control in metal and nonmetal mining prompted the Bureau of Mines to investigate the comparative effectiveness of three wet dust control techniques for face drilling. Previous attempts to achieve effective dust control on face drills with dry collectors have not met with success, the largest problem being sustained effective dust capture at the face. Results show that (1) foam-through-the-drill can provide 95-pct average total dust reduction in gypsum; (2) water mist-through-the-drill can provide approximately 91-pct average total dust reduction and 93-pet average respirable dust reduction in salt; (3) external boom-mounted water sprays can provide approximately 50-pet average dust reduction for both total and respirable dust in salt. The investigation showed that (1) foam and water in small quantities are very effective dust control techniques for face drills when applied through the drill steel at the point of dust generation, and (2) boom-mounted water sprays are only minimally effective for dust control on face drills.

Jan 1, 1981

By Wendell R. Peters

Shallow underground voids resulting from early coal mining and other resource recovery activities over the past several decades are now being recognized as a significant cause of ground subsidence problems. Uncertain knowledge of abandoned coal mines also imposes potential hazards in current mining operations since water inundation or the release of methane gas is a serious hazard when mine excavation operations break into an abandoned mine. Requirements for detecting and mapping subversive man-made tunnels in previous work has led to the development of a surface- operated automatic earth resistivity survey system and associated computer data processing system for military applications. Field demonstration tests of this system have resulted in successful detection of tunnels at depth-to- diameter ratios greater than ten to one. Under the sponsorship of the Bureau of Mines, a similar high-resolution earth resistivity system was designed and constructed for use as a potential means of detecting coal mine workings. The hardware and software aspects of the new system are described together with applications of the method to the survey and mapping of abandoned coal mine workings. Field tests are presented showing the detection of both air-filled and water-filled mine workings.

Jan 1, 1981

By Margaret Armstrong

The increasing cost of developing new mines and the need to mine more marginal deposits have led mining companies to use more sophisticated estimation methods such as kriging. But until recently, coal mining companies have shown little or no interest in these techniques. However, the stringent quality controls which are now placed on coal have led to a surge in interest in improved estimation methods. This can be seen from the -, number of research projects by private companies and governmental agencies on the application of geostatistics to coal reserve estimation. At present, most of these programs are centered on the problem of estimating the tonnage and the average grade (i.e. ash percent, sulphur content, calorific value, etc.) of the coal in-situ. See, for example, Sabourin (1975), Woods (1976, 1979), Pauncz and Nixon (1979) and Armstrong (1980). These studies show that the established techniques of linear geostatistics can be applied successfully to coal deposits. The study by Woods is particularly interesting because he had access to the actual production figures as well as the initial sample data from the no 2 seam in the Greenside Colliery owned by the Anglo-American Corporation. He showed that the estimates obtained by kriging were consistently closer to the actual production figures than those given by three other estimation methods. This confirms the superiority of kriging as a method of estimating block values for coal. Another advantage of geostatistics is that it can be used to determine the optimal spacing between drill holes. An example of this is given by Armstrong for the coking coal deposit in the Bowen Basin, Australia.

Jan 1, 1981

By Daniel Threlfall

The disposal of hazardous chemical wastes will be one of the major environmental issues of the 1980's. Approximately 50 million tons of hazardous wastes are produced yearly. One of the major aspects of the problem is the siting, design and construction of environmentally acceptable disposal facilities to accommodate this huge volume of material. Surface mines have been considered attractive for development as disposal sires for several reasons: 1. Surface mines represent an open pit that can conveniently serve as a repository for wastes. This could represent a significant economic savings when compared with sites on undisturbed lands chat might require extensive excavation or embankment construction.

Jan 1, 1981

By H. B. Salisbury

The Bureau of Mines conducted research to determine if low-grade California chromite ores could be beneficiated to produce products suitable for commercial use. This research is part of a Bureau goal to provide technology capable of using low-grade domestic ores to meet emergency demands of the Nation for metals and minerals and in particular those minerals, such as chromite, which are considered critical. Two ores from California were ground and treated using gravity concentration and magnetic separation techniques. An are from Auburn in central California, assaying 2.5 pct Cr203, was treated by tabling and magnetic separation to yield a nonmagnetic product containing 44.7 pct Cr203 at a recovery of 36.4 pct. Core drilling samples from the Seiad Creek area of northern California, assaying about 6 pct Cr203, were upgraded by tabling to yield a concentrate containing nearly 50 pct Cr203 with a recovery of 50 pct. Both products are suitable for metallurgical and/or chemical use.

Jan 1, 1981

By John Durkin, Roy J. Greenfield

This report discusses the configuration and system deployment for the postdisaster surface seismic system for detecting and locating trapped miners. It analyzes the results of 15 field tests to define a signal model, background noise levels, and subarray performance. A waveform modeling procedure is described and compared with observed waveforms. The resulting similarity indicates that the major factors affecting the signal amplitude, waveform, and spectral character are understood. A model is presented which gives the signal amplitude as a function of source type, source depth, and horizontal off- set between source and receiver. Using this model a curve is presented which gives the range at which a signal will be detected for different signal and noise levels. Finally, and most important relative to the mission of the sys- tem, the ability of the system to detect signals on one or more subarrays is put into a probabilistic framework. For a strong source it is almost certain that a subarray directly over the source will detect the signal. After signal processing, it is highly likely that signals will he detected on sufficient subarrays to locate the trapped miner. Location errors have been found to be less than 100 ft in the majority of cases. Techniques have been used that can reduce the location errors to this level even when soil layer variation between subarrays is severe.

Jan 1, 1981

This Bureau of Mines publication consists of an overview of the mine waste management research currently being conducted by the Bureau. The following papers, given at a Technology Transfer Workshop, emphasize the increasing importance of research related to the safety and environmental considerations of mine waste disposal In recent years. Current work related to legislation passed in the last 10 years and their subsequent standards includes the development of adequate monitoring systems, development of stability and seepage prediction and control techniques, control of runoff water, and control of leaching solutions. Selected topics are included here that cover coal mine waste disposal, embankment slope stability monitoring, flow failures of mine tailings impoundments, and controlled burnout of abandoned coal mine fires. The projects described provide a current documentation of problems being addressed.

Jan 1, 1981

By King K. Mak

The objectives of this study are to: (1) Assess current signing regulations and practices; (2) Develop effective signing guidelines; and (3) Evaluate the applicability and appropriateness of the proposed signing guidelines through field demonstration at representative mines. A literature search was conducted to determine the state of the art for signing applicable to surface mine haulage roads as well as survey of existing MHSA regulations and review of MSHA accident records. Nine representative mines were visited to gather information on current signing practices. Preliminary signing guidelines were then developed based on the abovementioned data. Field demonstration of the preliminary signing guidelines was conducted in which signing programs were implemented in two selected mines. Signing requirements were first assessed at each of the two participating mines. Subsequently, the necessary signs were designed, purchased, and installed at the two mines. Evaluation of the signing program as to its adequacy, appropriateness, and effectiveness was solicited from both mine management and operations personnel. Experiences gained from field evaluation were then incorporated into the final signing guidelines as presented in this final report.

Jan 1, 1981

By Rudolf E. Greuer

This report contains the practical application of a computer program for the simulation of ventilation systems under the influence of mine fires and other emergencies on five hardrock mines. The introduction describes the need for such a program, its basic features, and the range of its applicability which is mainly a function of the available ventilation data. The second chapter discusses program modifications, whose necessity or desirability was, during the application, discovered. The following five chapters, which comprise the major portion of the report, give the detailed description of the program application on the five mines. For every one of the selected mines, the ventilation system, the source of the used ventilation data and their preparation for computer simulations are outlined. Based on data for the airflow distribution solely, fumes concentrations in the mines are calculated for several assumed fire locations. Based on data for airflow and pressure distributions, ventilation disturbances caused by fires as well as the resulting fumes concentrations and temperatures are determined. The consequences for escape routes and the possible means to keep them free of fumes are discussed. To investigate the capabilities of the program, other contaminant sources and other potentially dangerous ventilation factors, like fan failures and changed surface temperatures, are simulated also. The results of the calculations have been entered into ventilation plans which makes them easier to scrutinize. All significant computer printouts have been attached.

Jan 1, 1981

By C. D. Iles

The philosophy used in designing and writing Duval's Sierrita mine design programs is discussed. The Sierrita Incremental Design system (SID) is reviewed with emphasis on Pushback Extraction Design (PED). FED is a method by which predesigned pushbacks are sequenced into an optimized period-by-period design that can be directly utilized in daily operations as well as intermediate and long range planning. The advantage of SID is that it provides a practical, mineable open pit design. PED is not a theoretical design system; it is in operational use.

Jan 1, 1981

By Robert Hochscheid

When the original water-only cyclone patents were established in the 1950?s, the supplies of low cost oil and natural gas were abundant and low selling prices for metallurgical and steam coal provided little incentive for developing more sophisticated coal cleaning systems. Bituminous coal sold for less than $5.00 per ton, and in this period many domestic coal producers discarded to the slurry pond the coal finer than 0.5-mm. For many producers, the selling price would not permit the recovery of the capital and operating costs required for dewatering and drying the fine coal. Water-only Cyclones Clean Fine Metallurgical Coal The first broad interest in the water-only cyclone became evident in the mid- 19601s, and though some work was done on coarser coals, investigators were particularly interested in cleaning coal finer than 0.5-mm. Flotation was the only fine coal cleaning method that was broadly accepted, but short-comings were recognized and investigators were looking for an effective fine coal cleaning device or system. Because of the greater market value and the need for reducing pyritic sulfur in metallurgical coals, much of the development work of the 1960's was done on coking coals.

Jan 1, 1981

By Stanley Ferguson

Since 1978, the Colorado Department of Health has become involved in specific investigations of possible radiation hazards among nonminers in Colorado communities. In each instance, the improper disposal of mill tailings has precipitated concerns and allegations of radiation hazards. This presentation is a brief summary of the findings, to date, of 4 such investigations involving tailings disposal problems in Canon City, Denver, Durango and Grand Junction, Colorado. Canon City In the summer of 1979, allegations of excessive cancer incidence were made at public hearings concerning an application for a Radioactive Materials License submitted to the Colorado Department of Health by the Cotter Corporation for a uranium mill at Canon City. Canon City is the site of a uranium mill operated since 1958 by Commonwealth Edison. Local residents accumulated figures and calculated rates suggesting a 2-fold excess in total cancer mortality. These rates were not adjusted or standardized for demographic varibles. A review of cancer mortality data and computation of age standardized rates for years 1950 through 1977 showed that Canon City's cancer mortality rates were within expected limits, actually lower than rates for the State of Colorado or the United States. The first slide shows rates for every fifth year, 1950 through 1975. Further, an analysis of Canon City cancer incidence data from the Colorado Central Cancer Registry revealed that 1979 incidence rates were not significantly different from Colorado rates, with the exception of prostate cancer. The next slide shows age standardized incidence rates for lung, colon, breast and prostate cancer. Data were also reviewed for leukemia, myeloma, lymphoma and cancers of the thyroid stomach, uterine certix, ovary, kidney, bladder-and brain, however, small numbers of cases prevented meaningful rate calculation. 1980 data are presently being analyzed. None of the data yet examined support allegations of radiation-associated cancer in Canon City. Denver In February of 1979, the Department of Health became aware of a number of radium mill tailing deposits in the Denver metropolitan area, remnants of the radium milling industry of the early 1900's. Several of the deposits were situated so as to possibly contribute significantly to radiation exposure of a small number of people over a period of several decades. The Department developed protocols for radiation surveys, dosage estimates and, for a small number of persons, body burdens determinations and peripheral blood lymphocyte cytogenetic studies. The results of this investigation suggested no measurable biomedical impact as a result of the radium deposits. Durango In October of 1979, a physician residing in Durango, Colorado released information from a preliminary analysis of lung cancer data suggesting an incidence rate several times expected in that city. The data were presented at a meeting of a citizen's group concerned about the possible health hazards of 2 uranium mill tailing deposits located in the south end of the city. Since cancer incidence data generally do not exist in most of western Colorado, a team of epidemiologists was dispatched to Durango to work with local physicians and hospitals in conducting an epidemiologic study of selected cancers for the period 1969 through 1978. After case-finding and record abstracting were completed, it was determined that sufficient data were available for study of only 3 sites: lung cancer, breast cancer and leukemia. The next slide shows age standardized incidence rates for these 3 sites for 1969-1978 for Durango and the State of Colorado. There are no significant differences in these rates. The data did show a geographic peculiarity with regards to the relative proportion of tumor types near the tailings deposits as opposed to away from the deposits, however, this finding is based upon very small numbers of cases and may represent only the random excursion of rates based upon small observations. This investigation suggests that if a carcinogenic hazard is present, it is too small to be detected by the study method employed. Grand Junction The Department of Health has been involved in the Grand Junction mill tailings problem for several years. In 1966, the Department issued an order terminating the practice of free public access to a 55-acre pile of uranium mill tailings. Prior to this order, an estimated 300,000 tons of material was removed. Of this amount, an estimated 50,000 tons was presumably used in residential and commercial construction. Despite many allegations of cancer and birth defects excesses in Grant Junction since the mid 1960s, the first epidemiologic study of cancer was conducted in the spring of 1977. Data from the Colorado Central Cancer Registry were analyzed and reported to the Executive Director of the Department of Health in June of that year. The findings of the first and preliminary study were an unexplained excess of acute leukemia and chronic myelocytic leukemia. The excess was based upon small numbers but was present across all age groups. No increase in chronic lymphocytic leukemia was evident.

Jan 1, 1981

Silver ore was first discovered in 1866 at Manhattan, and a few ore shipments were treated in a mill at nearby Belmont. The district was abandoned from 1869 to April 1, 1905, when rich gold float was discovered on what was to be called the April Fool claim. By early 1906, 4, 000 people lived in Manhattan. The San Francisco earthquake, in April of 1906, caused the withdrawal of capital from Manhattan and most of the mines were shut down. Later that year and in 1907, however, more strikes were made. The camp prospered until the mid-1920s, but a steady production of several hundred thousand dollars per year was sustained even during the great depression. Then, in 1939, Nevada's first bucket-line dredge was installed below the town and operated until 1947, producing $4.6 million in gold. The Houston International Minerals operation at Manhattan was started in July of 1980 at a throughput of about 545 mt per day (600 st per day). In contrast to the early day underground operations, Houston's mine is open-pit and processes low-grade disseminated ores. The ore is a metamorphic schist containing 2. 7 g Au and 1. 03 g Ag per mt (0. 08 oz Au and 0. 03 oz Ag per st). Some coarse gold, up to 1 mm in size, is present. Mining and haulage is done by a contractor. Stockpiled mine-run ore is crushed in three stages comprising a jaw crusher and two cone crushers, with screens ahead of the cone crushers. Crushed product, at about 19 mm (3/4 in.) size, is stored in a silo. Grinding is by single stage ball mill with the discharge passing over two hydraulic traps for coarse gold removal. These traps will be replaced in late 1980 by a two-cell Pan American jig treating the cyclone underflow. The jig hutch product, along with the hydraulic trap product that has been stored, will be treated further for gold recovery. The gravity tails will then be cycloned with the underflow being recirculated in the ball mill and the overflow being treated by flotation. A rougher concentrate is made in twelve No. 48 Galigher cells with the float tails being cycloned. Cyclone underflow is refloated in another four No. 48 cells; the overflow is treated in sluice boxes for further gold recovery before being sent by gravity to the tailings pond. Bulk flotation concentrates are cleaned three times with the final concentrate being thickened. The thickener underflow is then batch cyanided in mechanically agitated tanks and washed with barren liquor

Jan 1, 1981