Search Documents

By James R. Aggson

This Bureau of Mines report presents a finite element analysis of roof stresses associated with a 4-foot-high by 18-foot-wide underground coal mine entry. This analysis starts with known loading conditions determined in an underground coal mine in West Virginia and is extended to other possible underground loading conditions. The roof failures predicted by the finite element analysis under known loading conditions correlate well with the roof failures observed underground. The most probable failure modes are identified for the various loading conditions considered. Various failure preventive measures are discussed.

Jan 1, 1979

By John A. Herbst

In recent years, diminishing supplies of high grade ores and increasing consumption of mineral and metal products have demanded high efficiencies in extraction processes. The rising cost of energy has influenced plant operating policies. Rather than merely processing as much ore as possible, other process factors are being considered in process analysis, with energy consumed per ton of product produced taking on increased importance. Alternate processes and more efficient plant design may satisfy part of the demand placed on the mineral processing industries. However it is expected that the improvement of existing operatives will be responsible for most of the gains in efficiency in the short term. Even slight improvements in process efficiency lead to significant cost saving. Grinding, for example, is an inherently energy-intensive process. Grinding circuit capital and operating costs are high and it is essential that circuits run as efficiently as possible. In flotation plants, low-grade ores demand optimum recovery of valuables to maintain overall metallurgical efficiency. The use of modern data, treatment methods and systems analysis provide the means to achieve many goals, previously beyond reach. The design of more efficient plants and the evaluation and. improvement of existing plant operations constitute the general area of process analysis. Process analysis can be used to identify the capacity available in a process unit in some cases. In other cases, the goal may be to investigate alternative equipment configurations for an existing plant for possible improvement in efficiency. This goal is virtually impossible to achieve using plant data alone. A simulator of the process units involved can provide an excellent basis for performing the required process analysis.

Jan 1, 1979

By E. O. Mixon, Jack D. Kennedy

INTRODUCTION This contract is the most northerly portion of the Metropolitan Sanitary District of Greater Chicago's Tunnel and Reservoir Plan. (TARP) The project begins at Addison Street in Chicago and proceeds northerly approximately ten miles to end at Wilmette Harbor and Lake Michigan. The project which consists of 2 work shafts, 32 drop shafts, 7.322 km (24,020 ft.) of 6.7 m (22 ft.) diameter circular rock tunnel, 8.458 km (27,750 ft.) of 9.2 m (30 ft.) diameter circular rock tunnel and miscellaneous rock bolting and grouting, was bid for a total cost of $63,140,480. The tunnel invert elevation varies from 65.5 m (215 ft.) to 77.4 m (254 ft.) below the ground surface, which places the tunnel in a rock formation of dolomite limestone. At the tunnel invert, the unconfined compressive strength of the limestone varies from 96 MPa (14,000 psi) to 152 MPa (22,000 psi). The 6.7 (22 ft.) diameter tunnel required the mining of 10.9 cu m. (14.2 cu yd.) of rock per lineal foot of tunnel while the 9.2 m (30 ft.) diameter tunnel required the mining of 20.1 cu m (26.3 cu yd.) of rock per lineal foot of tunnel. The total cubic meters of rock required to be excavated from both tunnels was 818,821 cu m (1,070,978 cu yd.). All of this will be mined by tunnel boring machines (TBM). These tunnels were not to be lined with concrete. The thirty two drop shafts have upper portions that are cylindrical in the overburden and rock sections. They were divided into two groups, depending on diameter, with a different construction method for each group. The first group consisted of twenty three of the

Jan 1, 1979

By Peter A. Hacquebard

Recent drilling programs have shown that the in-situ coal resources of Nova Scotia are very substantial. The grand totals of the measured, indicated and inferred categories amount to 232 m, 646m and 993 m tons, respectively. This vast quantity of coal occurs essentially in five main fields: Sydney, Mabou, Port Hood, Pictou and Springhill. The largest resources (84% of the total) occur in the submarine area of the Sydney coalfield. With a 65% recovery rate, there are at present 150m tons of proven, recoverable coal in Nova Scotia. At a predicted maximum annual production of 5 m tons, this amount equals a lifespan of 30 years. However, additional drilling, particularly in the Sydney offshore area, holds promise of increasing the recoverable reserve tonnage to at least 350 m tons. This figure may be compared with the 484 m tons production obtained during 191 years of mining (from 1785-1976). The geological appraisal of the remaining coal resources in the five fields mentioned is presented in three-dimensional diagrams, per individual seam and corresponding reserve area. In addition, the submarine extensions of the Sydney and Mabou coalfields are discussed in light of results obtained from off shore oil exploration wells. The terminology and standards of coal resource calculations are pointed out, and the phenomenon of seam splitting and its prediction from geological data is illustrated. The availability in Nova Scotia of either thermal or metallurgical coal is considered in relation to rank and sulphur content. This paper was presented in June 1977 at the 90th Annual Meeting of the Mining Society of Nova Scotia. The coal resource estimates, however, have been updated to include the results obtained with the offshore drilling in the Sydney Coalfield to November 1977.

Jan 1, 1979

By Partridge A. C

Pinched Sluices, in a variety of guises, are used extensively for the separation of minerals according to density. In the authors' work a pilot-scale sluice has been constructed with provision for splitting the discharge stream into a number of layers. The composition and flowrate of the stream can thus be analysed as a function of depth and the results presented graphically. The effects of such parameters as total flowrate, pulp composition and particle size on overall performance can be clearly seen from such data.

Jan 1, 1979

The ore reserves of the Frieda porphyry copper prospect in Papua New Guinea have been estimated using kriging and an alternative method. Only very erratic variograms could be obtained from the raw data and thus it can be expected that kriging variances will be unrel- iable. The frequency distributions of the two sets of estimates show expected differences and the resulting mineable reserves show similar expected differences. More drilling and the use of disjunctive kriging are needed to produce reliable estim- Ates.

Jan 1, 1979

By Simpson JF, Murrie SJ

In determining new areas for slag disposal a foamed slag aggregate has been developed for use as a skid resistant material. The foaming of the slag does not rely on the use of water, but rather on the slag chemistry. Laboratory test results indicated that a product having good skid resistant properties has been prod- uced. A section of road is being assessed for performance of the aggregate in a surface dressing application under heavy load. The results from the test section after seven months have shown that the foamed slag is suitable for this application. Further test sections are now being considered.

Jan 1, 1979

By Louis W. Riggs

The primary concern in dealing with contractual arrangements for construction is getting the work completed satisfactorily, in the shortest time, and for the least expense for the owner--while assuring that all other parties associated with the contract make a reasonable profit for their effort. In our complex construction climate of today, achieving all of these is usually not possible. Somewhere between the beginning of design and the completion of the work, disagreements and delays arise which can destroy the best of intentions. Assuming that all parties associated with the contract are acting honorably and professionally, the disagreements generally arise through inappropriate contract types or through flawed contract documents. These flaws can be either sins of omission or commission, but we must find a way to lessen, if not completely eliminate, their impact. Disagreements and delays are directly related to the extra cost which the owner and the other involved parties must suffer. Usually the attorneys are the only ones who come out on the positive side. Inappropriate or defective contract documents can be the result of inadequate time for preparation and review, laziness in not searching out the proper terms and language, insufficient recognition of the proper assignment of risks, or just ignorance as to what is right and what is wrong for the particular project. They can also result from a client, particularly a public agency, providing rigid general conditions and format requirements with which the engineer is not allowed to tamper. Arguments

Jan 1, 1979

This excellent paper by Dr. Colombo parallels quite closely the bench and pilot work done by the Hanna Research Laboratory on the Mesabi oxidized taconites. Because of the vast reserves and future ore requirements the need to perfect the selective flocculation-flotation process becomes very necessary. The selective flocculation process is a very efficient method of desliming, leaving a fairly clean, upgraded product for flotation. However, one of the problems that we have encountered in this process was some very fine, -2 micron liberated goethite in the slimes that did not flocculate. The complete slime removal is not necessary. We remove slimes to the extent of about 5% of the iron units. However, on difficult treating ores we would remove more slimes. The reclaimed water from our pilot plant has a turbidity of about 1000-3000 ppm. We can obtain lower turbidity water but to do this would involve additional lime as a tailing flocculant and we would run the risk of flocculating the entire ground pulp in the selective flocculation process because of the increased Ca level in the water. We have about seven different geological ore types out of 17 recognizable ore types that are treatable. All of these ore types require different degrees of dispersion and grinding which is a problem. The use of acrylic acid polymers as a selective flocculant has been patented by the American Cyanamid Co. This will-have to be

Jan 1, 1979

By S. L. Crouch

This paper describes a numerical procedure for the computation of the displacements and stresses induced by the mining of a tabular ore deposit in faulted ground. The numerical procedure is based on the displacement discontinuity method, which can be regarded as an application of Salamon's 'face element principle' to cases in which the reef plane is faulted into several sections, or even folded in an arbitrary way. An element of a fault is modelled in the same manner as an element of the reef, except that a fault element is allowed to undergo permanent inelastic deformation (i.e., slip) if the stresses transmitted through the fault-filling material satisfy a Mohr-Coulomb yield condition. An iterative technique for the incorporation of a Mohr-Coulomb yield condition in the general displacement discontinuity method is explained. This technique is illustrated by means of a simple example involving the mining of a flat-lying reef intersected by a fault. The displacements and stresses at selected locations along the fault are examined as the reef is mined, element by element. A consideration of the energy changes reveals that the occurrence of slip along a fault leads to a sudden increase in the energy release rate due to mining as the excavation intersects the fault. The energy release rate then falls off abruptly to a value less than that which would occur in the absence of any slip, and gradually builds up to re-establish the conditions that would exist in unfaulted ground.

Jan 1, 1979

By A. T. Iannacchione

The Bureau of Mines established geologic factors affecting the mining of the Lower Kittanning coalbed to aid in coalbed minability studies and examined the occurrence of "wants" (places where coal is missing) and types of unstable roof rock strata. Trends established from mapping, including prediction of areas of high methane emissions, were extrapolated to unmined areas. 'Wants' in the coalbed are of two types: Erosional and depositional. Erosional features occur where north-south-trending sand-filled channels cut into the coalbed. Variations in depositional environments have caused the coalbed to "split" into several thinner units. Slickensides, commonly indicative of unstable roof, are adjacent to and on the underside of sandstone channels; they were caused by differential compaction and by soft sediment sliding along the contact between the sandstone and adjacent shale. The frequency of unstable roof also increases where the interval between the Middle and Lower Kittanning coalbed is less than 30 feet. The zones of weakness at the contacts above and below the Middle Kittanning coalbed are the controlling factors for unstable roof in these strata. Methane emissions from the coalbed are controlled primarily by depth, fracture permeability, and rank of coal. Local geologic factors are coalbed thickness, associated rock strata, structure, and proximity to outcrop.

Jan 1, 1979

By J. D. Miller, J. E. Sepulveda

Tar sand deposits in the state of Utah contain more than 25 billion bbl of in-place bitumen. Although 30 times smaller than the well-known Athabasca tar sands, Utah tar sands do represent a significant domestic energy resource comparable to the national crude oil reserves (31.3 billion bbl). Based upon a detailed analysis of the physical and chemical properties of both the bitumen and the sand, a hot-water separation process for Utah tar sands is currently being developed in our laboratories at the University of Utah. This process involves intense agitation of the tar sand in a hot caustic solution and subsequent separation of the bitumen by a modified froth flotation technique. Experimental results with an Asphalt Ridge, Utah, tar sand sample indicated that percent solids and caustic concentration were the two most important variables controlling the performance of the digestion stage. These variables were identified by means of an experimental factorial design, in which coefficients of separation greater than 0.90 were realized. Although preliminary in nature, the experimental evidence' gathered in this investigation seems to indicate that a hot-water separation process for Utah tar sands would allow for the efficient utilization of this important energy resource. The projected increase in the ever-widening gap between the domestic energy demand and the domestic energy supply for the next few years has motivated renewed interest in energy sources other than petroleum, such as tar sands, oil shale and coal. Although a number of research programs on the exploitation of national coal and oil shale resources have already been completed, very few programs have been initiated on the processing of tar sand resources in the United States. In recognition of their significance as a domestic energy resource, investigators at the University of Utah have designed an extensive research program on Utah tar sands. An important phase of this program, and the main subject of this publication, is the development of a hot-water process for the recovery of bitumen from Utah tar sands, as a preliminary step toward the production of synthetic fuels and petrochemicals. The term "tar sand" refers to a consolidated mixture of bitumen (tar) and sand. The sand in tar sand is mostly a-quartz as determined from X-ray diffraction patterns. Alternate names for "tar sands" are "oil sands" and "bituminous sands." The latter is technically correct and in that sense provides an adequate description. Tar sand deposits occur throughout the world, often in the same geographical areas as petroleum deposits. Significantly large tar sand deposits have been identified and mapped in Canada, Venezuela and, the United States. By far, the largest deposit is the Athabasca tar sands in the Province of Alberta, Canada. According to the Alberta Energy Resources Conservation Board (AERCB),2,3 proved reserves of crude in-place bitumen in the Athabasca region amount to almost 900 billion bbl. To date, this is the only tar sand deposit in the world being mined and processed for the recovery of petroleum products. Great Canadian Oil Sands, Ltd. (GCOS) produces 20 million bbl of synthetic crude oil per year. Another plant being constructed by Syncrude Canada, Ltd. is expected to produce in excess of 40 million bbl of synthetic crude oil per year. According to the Utah Geological and Mineral Survey (UGMS), tar sand deposits in the state of Utah contain more than 25 billion bbl of bitumen in place, which represent almost 95% of the total mapped resources in the United States.4 The extent of Utah tar sand reserves seems small compared to the enormous potential of Canadian tar sands. Nevertheless, Utah tar sand reserves do represent a significant energy resource comparable to the United States crude oil proved reserves of 31.3 billion bbl in 1976.5 Tar sands in Utah occur in 51 deposits along the eastern side of the state.4 However, only six out of these 51 deposits are worthy of any practical consideration (Fig. 1). As indicated in Table 1, Tar Sand Triangle is the largest deposit in the state and contains about half of the total mapped resources. Information regarding the grade or bitumen content of Utah deposits is still very limited. The bitumen content varies significantly from deposit to deposit, as well as within a given deposit. In any event, the information available6-8 seems to indicate that Utah deposits are not as rich in bitumen as the vast Canadian deposits which average 12 to 13% by weight.9 Although many occurrences of bitumen saturation up to 17% by weight have been detected in the northeastern part of the state (Asphalt Ridge and P. R. Spring), the average for reserves in Utah may well be less than 10% by weight. Separation Technology As in any other mining problem, there are two basic approaches to the recovery of bitumen from tar sands. In one

Jan 1, 1979

By Andrew Ritter, Victor I. Montenyohl, Stephen R. Winzer

Thirty-seven open pit production blasting operations have been monitored using high-speed cameras running between 500 and 7000 frames per second. Analysis of the resulting films reveals irregularities in timing including sequencing errors and crowding (holes firing less than 8 ms apart), confirming results of laboratory testing of ms delay blasting caps (Winzer, 1978). Where blasting parameters are otherwise constant and within recommended guidelines (stemming, spacing, burden, etc.), timing problems dominate the overall performance of the blasting operation. Model tests in layered Homalite 100, designed to simulate joint or bedding planes in rock, indicate the importance of the stress waves generated by the explosive in developing the crack network which is ultimately responsible for the fragmentation seen in the resulting muckpile. These mechanisms are strongly supported by high-speed film studies at Pinesburg, Maryland. Experiments in controlling relief in deep shots (where depth approaches the lateral extent of the bench blasted) using borehole geometry and hybrid initiation systems (electronic timer and pyrotechnic delays) were carried out. The results suggest that the 1 me/ft. of burden guideline developed by Bergmann et aI., 1974 is too short, and that much longer times are necessary to optimize fragmentation and muck digability. Longer times are found to reduce noise, vibration, and flyrock.

Jan 1, 1979

By C. Ogasawara

This document describes the direction and progress of the Bureau of Mines Oil Shale Mining Environmental Research Program as of January 31, 1979. It is aimed at focusing the Bureau's role in environmental research supporting oil shale development with respect to the activities of other involved government agencies and private industry. Environmental considerations in oil shale extraction, such as ecological disturbances, health and safety hazards, waste management, and socioeconomic impacts, are discussed along with the type of research known to be planned by organizations to ameliorate these problems.

Jan 1, 1979

By John A. Meech, J. G. Paterson

Activated carbon is a strong adsorbent for amyl xanthate, capable of removing from solution up to a quarter of its own weight in xanthate. In selective flotation system where depression is unstable, separation efficiency increases with activated carbon additions. The improvements observed are brought about by two mechanisms. First, by removing stripped and residual collector ions from solution, competition between depressant and xanthate is reduced and depression is stabilized. In addition, the texture of the froth phase at high pine oil concentrations is modified by activated carbon such that better drainage between the air bubbles takes place, alleviating the mechanical entrapment of depressed mineral particles. In treating a bulk copper/lead concentrate produced from GECO ore, selectively between galena and chalcopyrite is increased when activated carbon is used. Although the rate of flotation of galena is marginally lowered by activated carbon, a small extension in the duration of flotation allows the lead recovery to increase by 19% at the same recovery of copper. An addition rate of 0.75 kg/ton (1.5 lb/st) of bulk concentrate is suggested as optimum from this testwork. However, the actual level used in the mill is dependent upon the residual concentrations of collector and frother in the bulk concentrate pulp.

Jan 1, 1979

By D. E. Traut

The effect of various ion concentrations on uranium absorption from a sodium carbonate solution by a strong-base, anion resin was investigated by the Bureau of Mines in support of its objective to help assure an adequate uranium supply for future needs. The studies were conducted to improve the recovery of uranium from in situ leach solutions by ion exchange. The effects of carbonate, bicarbonate, chloride, and sulfate ions were examined. Relatively low (less than 5 g/l) concentrations of chloride, sulfate, and bicarbonate were found to be detrimental to the absorption of uranium. High (greater than 10 g/l) carbonate concentrations also adversely affected the uranium absorption. In addition, the effect of initial resin form was investigated in tests of the chloride, carbonate, and bicarbonate forms; resin form was shown to have no effect on the absorption of uranium.

Jan 1, 1979

By P. D. R. Maltby

This paper describes the background and markets for calcium carbonate and silica sand in Canada, as well as the results of recent test work carried out at the Ontario Research Foundation. Tests on sericite, tremolite, vermiculite, barite and graphite are also mentioned.

Jan 1, 1979

By D. B. Stewart

This paper reports on an investigation undertaken to determine the exhaust gas temperatures of operating underground mining equipment. The effectiveness of platinum catalytic purifiers is discussed. From exhaust temperatures, it is concluded that LHD engines are highly loaded, haulage truck engines are moderately loaded and utility vehicle engines are lightly loaded.

Jan 1, 1979

By Daryl R. Tweeton, Jerry R. Riding, Grant Buma, Frank J. Rosswog

In situ solution mining of uranium has environmental advantages over conventional mining. The leaching of uranium, however, alters the ground-water quality in the aquifer where the mining occurs. Currently, regulations require that the ground water be restored to approximately its original condition. This paper, a summary of a study funded by the Bureau of Mines, reviews the state of the art in restoring ground-water quality after in situ uranium leaching. Current restoration practices discussed include disposal of liquid wastes in deep disposal wells and evaporation ponds, producing from all wells during restoration, and recirculating water purified in surface plants. Methods for predicting the effectiveness and cost of current techniques are presented. Possible alternative techniques are also described. Two restoration operations are discussed.

Jan 1, 1979

By Brian Raymond

This paper will outline the problems and solutions of the new generation washeries, as well as the recent technological advances which are being considered for future coal preparation plants. The subjects to be covered will include: - reasons for considering coal preparation plants; - raw coal crushing and handling systems; - types of coal cleaning equipment being used versus new equipment being considered; - fine coal circuit sizing; - clean coal centrifuging and dewatering; - thermal dryer problems and changes; - fine refuse dewatering systems; - clean coal storage problems and changes; - materials handling within the plants; and - control systems for preparation plants. The design and integration of the various circuits that form a modern coal preparation plant have led to the creation of an exciting new field of industrial research. As the need for energy sources increases, efficient methods of preparing coals for specific markets will become more important.

Jan 1, 1979