Search Documents

By C. Kwong, L. H. Rorden, T. C. Moore

This report describes the feasibility test of an electromagnetic method for locating, boreholes, with or without casing, that have been drilled in conjunction with mining operations but whose location with respect to the tunnel is not precisely known. The first tests were conducted with the cooperation of the Kerr-McGee Corporation, Church Rock Mining Operations, New Mexico, in September 1977. These tests demonstrated that accuracies of better than ±15% of range and ±1° of bearing can be achieved with a simple system and setups. Subsequent tests, in January 1978, on a horizontally drilled pipe line river crossing application, by Ti tan Contractors of Sacramento, California, demonstrated that accuracies of better than one-half percent of range and a few tenths of one degree of bearing can be achieved by using refined techniques. The demonstration tests were done at ranges on the order of 100 to 200 feet but the method is capable of working at much greater distances.

Jan 5, 1978

By Raymond E. Zimmerman

ROBERT E. HOCHSCHEID (Krebs Engineers, Cyclone Div.)--The subject article appears in the February, 1978, edition of Mining Engineering, and on page 190 carries the statement, "As most operators know, in a Water-Only cyclone, ability to adjust the vortex finder is quite important due to the sensitivity of this type of operations to variance in feed conditions and having to take them apart to make this adjustment is always a nuisance." Our experience as a manufacturer and supplier of Water Only cyclones does not agree with the above statement, and we offer the following brief discussion.

Jan 5, 1978

By Paul R. Wieber, Atam P. Sikri

This paper describes the U. S. Energy Research and Development Administration's (ERDA) program to develop in situ coal conversion processes, especially gasification. The potential of this technology, the technical directions being explored, and the program strategy to carry the process concepts toward commercialization are emphasized. The geographic location of the U. S. coal resources and a market analysis are described. Commercially successful in situ coal processes could add over a trillion tons of coal to the U. S. coal reserves. The economics of these processes is compared with surface gasification. Independent studies show this process to be 25% cheaper than surface gasification for Western coals. The major projects are briefly described. The Linked Vertical Well process is in the most advanced stage and shows great promise. The last test produced a low-Btu gas averaging 171 Btu per standard cubic foot for average production rates of 8.5 million standard cubic feet per day. The other projects are Packed Bed, Longwall Generator, and Steeply Dipping Beds. Unique factors of the process development are discussed which may lead to commercial processes in the near term. A development strategy is proposed by which this technology could be commercialized before 1985 with potentially lower gas prices and lower environmental impacts, relative to mining plus surface gasification.

Jan 5, 1978

It is probably safe to say that, as the economic well-being of the mining industry goes, so goes the fortunes of mineral explorationists. And in 1977 the industry was not well at all. The year-long depression of the copper industry, marked by layoffs, temporary shutdowns, and mine closures, provided an appropriate background for the collapse of the nickel market, passage of a surface mining law that will affect the hard-rock industry in ways that are yet unclear, and the threat of operating under a new set of rules brought on by reform of the Mining Law of 1872.

Jan 5, 1978

By M. L. Jeremic

Abstract-Observations of ground behavior in mining the Choka Dulkan ore body have been described. Ore recovery was limited to approximately 60% because unconsolidated hydraulic fill did not permit either the widening of stope spans nor secondary ore recovery from pillars. Stope undercutting induced high stress concentrations. However, as extraction progressed, ground conditions improved but before extraction was complete they deteriorated again. After completion of a stope, the remnant rib and crown pillars continued to be deformed by other stresses for some time.

Jan 4, 1978

By K. W. Warren, F. R. Prestridge, B. A. Sinclair

Separating oil from water may seem simple enough, but in fact, tremendous efforts have gone into this common process problem. The petroleum industry is constantly looking for better ways to separate the emulsion of oil and connate water that is pumped from the ground and its latest development, the electrostatic emulsion separator, may find an important offshoot application in hydrometallurgy. The patent-pending OSX coalescer, developed by C-E Natco, recovers entrained solvent from both raffinate and the pregnant strip liquor. It has already undergone successful testing at the Bluebird copper circuit in Arizona and is currently being prepared for testing at a uranium SX plant.

Jan 4, 1978

By J. A. Herbst, J. L. Sepulveda, J. D. Miller

Abstract-Lead cake, a zinc smelter flue dust residue, consists primarily of lead sulfate. Characteristic properties of lead cake were determined in order to aid the understanding of reaction mechanisms involved in bismuth removal from lead cake by sulfuric acid digestion. Sp gr (specific gravity) measurements, surface area measurements, and photomicrographs revealed that the particles of lead cake are quite porous and seem to consist of an agglomeration of submicron grains (0.4 pm) fused together in a manner similar to cement clinker. Analysis of experimental rate data, which was independent of particle size, indicates that the dissolution reaction involves two distinct, rate limiting steps. The initial stage of reaction appears to be limited mainly by intergranular diffusion of the reactant, hydrogen ion, while the latter stage of reaction appears to be controlled by diffusion of soluble reaction products through the reaction product layer of the individual grains.

Jan 4, 1978

By Clement K. Chase, F. Milton Lewis, Roshan B. Bhappu

Abstract-In this paper an attempt has been made to review the cost trends in producing copper by conventional milling, smelting and hydrometallurgical means during the last five years. The primary objectives of this cost analysis are to provide a base for future projections as well as to indicate which cost items are more volatile in their influence on overall cost of producing copper.

Jan 4, 1978

The technique of hard facing can be a quick and economical means of prolonging wear-life of many metals, but maintenance personnel must first select the proper alloy from the hundred that are available. Even then, roper selection is effective only when it is properly applied by the welder. To complete the successful weld, several hints are offered:

Jan 4, 1978

By T. A. Kauppila, V. Rajaram, R. L. Bolmer

With steadily increasing prices for imported oil, commercial production of oil from oil shale can become a reality in the near future. Presently we are importing about 43% of our oil needs and this reliance on foreign oil can be reduced by utilizing the vast resources of oil shale in the western US. The oil shale resources in Colorado, Utah, and Wyoming, averaging 0.06 m3/ton (15 gal per st) and occurring in beds at least 3 m (10 ft) thick, are estimated at 293 Gm3 (1842 billion bbl) of which only 97 Gdm3 (610 billion bbl) are recoverable with current technology. The full potential of this vast resource can be realized only if significant steps are taken toward improving mining and retorting technology and solving environmental problems. Oil shales with a grade of 0.08-0.10 m3/ton (20-25 gal per st) are amenable to mining and surface retorting; whereas lower-grade oil shales may be recovered by in situ retorting.

Jan 4, 1978

By Garland R. Dever, Preston McGrain, George W. Ellsworth

Abstract-Limestone resources for industrial, constructional, and agricultural uses occur on the surface and at minable depths in several areas along the Ohio River and its navigable tributaries in Kentucky. High calcium and high carbonate limestones suitable for use in cement and lime production, steel manufacture, environment control measures, and other special uses are present in the High Bridge Group (Ordovician) and Warsaw and Ste. Genevieve Limestones (Mississippian). Deposits with thicknesses of 7.3 to 20.7 m, (24 to 68 feet) have been documented by the analysis of samples taken at 0.3-m (1- ft) intervals. Active and potential mine and quarry sites afford access to water transporation and proximity to a number of industrial and metropolitan centers. Geologic factors affecting the distribution of deposits include the Cincinnati arch, regional dip into the Appalachian and Eastern Interior basins, complex faulting in and near the western Kentucky Fluorspar mining district, and late Paleozoic, erosional unconformities in northeastern Kentucky.

Jan 4, 1978

By Thomas M. Plouf

Getting optimal performance from flotation cells can, in many cases, be critical to a project's economic viability. Simple testing procedures can sound early warning signals as well as maintain optimum recoveries from the flotation cycle. The materials required for a simple testing laboratory include: (1) pH meter or pH paper, (2) bottles of reagents used in plant flotation, (3) stop watch, (4) calibrated eye droppers. (5) laboratory flotation machine (1000-g tank, open impeller), (6) froth collection pans, (7) magnifying glass, (8) sizing screen sufficient to retain 10% of the flotation feed coarse fraction, (9) sizing screen for the size particles at which desliming of the plant flotation feed is to take place, and (10) a set of screens covering the complete range of feed particle size.

Jan 4, 1978

By Lawrence A. Soltis

Senior engineering or executive management positions are filled by engineers who are evaluated on their performance, knowledge, skill, and maturity. Not only is technical expertise required but a knowledge of sales and marketing, finance, law, industrial relations, and public affairs is necessary. The University of Wisconsin-Extension offers an innovative post-baccalaureate degree program blending technical and professional subjects the Professional Development Degree in engineering (PDD)-designed to bring various opportunities for learn-

Jan 4, 1978

By J. E. Nelson, R. J. Bonnis

Recent completion of Cyprus Bagdad's $240-million modernization and expansion program has registered a 700% increase in ore production with only a 50% increase in labor. Elements of this remarkable achievement include the application of large-scale mining equipment as well as the selection of the latest in processing hardware. Most important, however, was the early recognition that Bagdad's labor personnel is its most important asset.

Jan 4, 1978

By John Bonar

A switch to refractory-type slurry pump linings has significantly reduced maintenance costs arising from liner failure at a Missouri lead mill. The pumps routinely handle a slurry consisting of 79 to 81% solids with occasional tramp iron, and are subjected to intense abrasion which previously wore out rubber liners in anywhere from three days to two months. Average liner life at the 1.5-million-t/y (1.6-million-stpy) operation was 30 days. Experimentation with mild steel liners and even manganese steel liners failed to extend liner life beyond two months.

Jan 3, 1978

By Robert N. McIndoo

A good tire program must begin at the top; management must have an awareness of the tremendous potential for cost saving that tires represent. At Reserve Mining Co., tires account for 33% of the cost of maintaining its 44 tractor-trailer side-dump haulers and 22% of its 32 rear-dump trucks. In comparison, engine overhauls account for only 6% of the maintenance dollar. Doubling the present engine life would save only 3%. The open-pit mine, located near Babbitt, Minn., moves about 46 million t/y with its off highway fleet. Mine roadways total in excess of 160 km (100 miles) and about 1200 tires are in active use at any given time.

Jan 3, 1978

In high-volume mining operations, preventive maintenance programs that include standardized replacement wear parts can boost equipment availability and lower unit costs. Meeting the daily production targets depends heavily on keeping equipment working as close to full time as possible. This is the case at one medium-sized western surface coal operation producing approximately 2.7 million t/y (3 million stpy). The mine, located in western Wyoming, removes in excess of 8 million m3 (10.5 million cu yd) of highly abrasive overburden each year. According to the mine superintendent, "Abrasion at this mine is some of the worst I've ever seen. Shovel points can wear out in little more than one shift. Dozer blades some- times last two weeks, but can wear out sooner. And ripper points really take a beating. If we can replace this fast-wearing iron with small pieces that go on quickly, we think that's the way to go."

Jan 3, 1978

Belting worth thousands of dollars can be ruined in a few minutes because of careless maintenance or lack of maintenance. Proper belt conveyor maintenance means having a clean conveyor system at all times. The belt line should be visually inspected during each shift. Equipped with proper maintenance instructions, one belt man can patrol a belt line of 2 to 3 km (1.5 to 2 miles). His duties would be to lubricate drives and idlers (except sealed-for- life type), maintain belt and conveyor frame alignment, detect sticking idlers, and maintain an unobstructed right-of-way.

Jan 3, 1978

By Donald W. Gentry, John F. Abel

This paper presents some of the results of a rock mechanics instrumentation program designed for, and implemented at, longwall panel 4N at the York Canyon Mine near Raton, New Mexico. The objective of this particular instrumentation program was to determine the response of the rock mass to longwall mining of a thick coal seam utilizing shield-type supports. Measurements were made in the rock along the ground surface, above the coal seam, in the coal seam, and immediately below the coal seam. Longwall test panel 4N had a total developed length of 762 m (2500 ft) and a face width of 168 m (550 ft), Fig. 1. The seam mining height in the panel area was approximately 3 m (10 ft). The average depth of overburden above the panel is 107 m (350 ft) although it ranges from 73-134 m (240-440 ft). Roof support at the face was provided by 116 Hemscheidt 320 HSL shields. These shield-type supports weigh 11.4 metric tons each.

Jan 3, 1978

By Thomas L. Kesler

Lithium raw materials usable with present technology consist of pegmatite ore and shallow evaporite brine. Deposits of these materials occur in many parts of the world. Those advantageously located supply the present lithium industry. Less favorably located deposits will come into production as markets expand and present sources are depleted. In this discussion, materials listed as reserves include fully explored and partly explored deposits. For those closely drilled and assayed, the data provide measurements rather than estimates, and such reserve tonnages are "proved." For deposits partly explored, the data support reserve estimates of "probable" tonnages. Materials lacking exploratory data are classed as resources, and their "possible" tonnages are inferred mostly from indirect evidence and are essentially objectives for exploration. All figures for pegmatite ore apply to total materials in the ground.

Jan 3, 1978