Search Documents

By R. D. Lord

This paper deals with the search for the best practical means of storing sulphide bearing tailings, where there is no residual excess of carbonate material. It is the common experience that the sulphide content decomposes, with the aid of bacterial action, and the resulting sulphuric acid escapes, along with any heavy metal solutes, through embankments that are usually porous to some degree. The problem is typified in the tailings of the uranium operations of Elliot Lake, Ontario, where mining started some 20 years ago. The approach to tailings disposal paralleled the practice for other hydrometallurgical plants treating gold and base metal ores. Impoundment areas were designed to retain solids, and a clear and neutral overflow was considered satisfactory practice. Now experience has shown that these areas, some idle for over a dozen years, release acids, in seepage and overflows, to an unacceptable degree. To protect natural water courses neutralizing plants are operated wherever required. Lime slurry is fed continuously into the tailings outflows in a quantity sufficient to raise the pH to 8.5 and precipitate heavy metals that may be in solution. The objection to this procedure is that the plants will require servicing indefinitely, unless a better remedy is found.

Jan 1, 1975

Coal is a very versatile resource, having variable characteristics and having potential for a wide variety of mar- kets. Australia has extensive deposits of black coal, although they are concentrated mainly in Eastern Australia. Assessments of the currently known reserves are related to the qualities of these reserves. Markets available to black coal fall into the broad groupings of metallurgical, fuel, conversion and miscellaneous markets and the requirements of these markets are related to coal characteristics. Market trends in Australia and on the export market are discussed and projected forward. By the end of this century Australian consumption of black coal could well be 100 million tonnes per annum, and, in the absence of any export restriction, a similar amount is likely to be exported. Currently defined black coal resources in Australia will last at least 600 years at these projected rates of consumption. Although the position appears satisfactory in considering the projected life of the black coal resources, there is a serious lack of detailed information on reserves, mining and preparation yields, quality and possible environmental restrictions. Action is required on three parallel courses: (1) a consistent, systematic and extensive survey of current coal resources in Australia, (2) accelerated exploration activity to define poorly prospected and potential areas, and (3) regular updating and extension of the knowledge of Australia's coal resources. This information would be of tremendous assistance for the formulation of a national energy policy on coal.

Jan 1, 1975

By Franklin H. Persse

To meet escalating energy requirements, substantial increases in production from the strippable coal and lignite deposits in eastern Montana, western North Dakota, and northeastern Wyoming already have occurred, and further expansions are expected at least until the year 2000. Such production, attributable largely to rising demand for low-sulfur coal, must be accomplished with a minimum of adverse effects on the environment. Information on geology, climate, and current land use in the Upper Missouri River basin is presented in the Bureau of Mines review as a guideline to what operators may expect during and after mining. Proven methods of protecting the air and water from pollution and of restoring mined land for other uses are described, and untried methods of land reclamation, some with equipment yet to be manufactured, are discussed as possible means of maintaining aesthetic values in the basin. Costs incurred to protect the environment are part of the production cost and thus are borne by the ultimate consumer. Unit production costs are less for the thick coal and lignite deposits of the basin than for the thinner but higher Btu coal deposits of the Eastern and Midwestern United States. Precise comparisons of environmental protection costs between mines in such disparate areas cannot be made, because of differences in physical conditions, accounting procedures, and other variables.

Jan 1, 1975

A comparison is made between elementary block estimation techniques and the optimal methods of geostatistics using data from an Australian deposit. Considerable improvement in the estimates are obtained by using the optimal technique in this case.

Jan 1, 1975

By John J. Dran

In recent years, market rates of interest have risen well above their historical long-term average. Also during this period, the short-term variability of interest rates has been greater than in prior years. Interest rates have a significant effect on the operation of our economy. They influence the extractive industries in a number of ways. Their major long- range impact is on investment decisions - specifically the valuation of mineral deposits. An understanding of the factors that influence interest rates is important to the engineer or businessman who makes the investment decisions for the mining company. The effect of changes in the market rate of interest on the value of mineral reserves is critical to the future financial success of the mining enterprise. The most common simplification of the factors determining the level of interest rates is that they are a function of the demand for and the supply of money. While this is an oversimplification, most businessmen would be hard- pressed to provide a better explanation. The purpose of this paper is to explore certain fundamental economic aspects of interest rates and to examine their effect on the analysis of investment in mineral deposits.

Jan 1, 1975

By Iain Weir-Jones

The efficient operation of an open pit mine presupposes that the slopes are maintained at an angle which closely approaches that of the ultimate stability of the slope. In order to do this in a safe manner, it is essential that the data relating to the behavior of the slopes be monitored and made available, through an instrumentation system, to the appropriate personnel so that soundly-based engineering decisions may be reached with the minimum of wasted effort. In addition to simply detecting potential failures, the system should also define what type of failure is developing; i.e., rotational, wedge, or dilational failures. Providing this data is the prime function of a stability monitoring system. Therefore, in an operating open pit mine, the instrumentation system must provide information which will have a direct bearing upon both the safety and the economics of the operation, as well as provide data which is pertinent to initial design, or to the re-design of slopes where developing instability is found to be a problem.6 It is possible to excavate pit slopes which will remain stable under extremely adverse conditions; however, such slopes would usually be so flat that they would tend to render the operation of a pit uneconomical which might otherwise be mined at a profit. On this basis, all practical pit slopes must be considered to be, to some ex- tent, unstable; if they are not, the design is too conservative and the mine is not returning its maximum profit. To reduce the problem to its fundamentals, one can simply state that the ideal pit slope design produces a slope which stands with zero maintenance for the entire life of the pit and then collapses into the final excavation as soon as the personnel and equipment have been removed. Such a design is impossible to achieve, but the fact remains that an efficient slope would hover on the edge of failure for the life of I the pit. As one retreats from this position, the profitability of the mine decreases because of an unduly conservative design.

Jan 1, 1975

By Yoginder P. Chugh

Elastic and viscoelastic behavior of three rocks-Tennessee sandstone, Barre granite, and Indiana limestone-was studied experimentally under uniaxial tensile stress. Cylindrical specimens of these rocks, about 1.0 in. diam and 2.0 in. long, were subjected to incremental constant stress history under uniaxial tension. The stress was held constant for a period of 40 min at each stress level. During this period, longitudinal and transverse strains on specimens were continuously monitored. The straintime history at each stress level was analyzed for elastic and viscoelastic parameters of a generalized Burger model. The viscoelastic parameters under uniaxial tensile stress were compared with those under uniaxial compressive stress. The experimental setup, experimental procedure, analysis techniques, and more significant results are described. This limited research effort clearly indicates the importance of the mechanical behavior of geologic material under tensile stresses.

Jan 1, 1975

By Robert D. Saltsman

Two modes of seal application were identified, and promising state-of-the-art seals of both types -shaft and drum -were selected for initial rating by non-destructive testing. Only one shaft seal survived the initial test, and a search was made for other candidate seals including new seals. One new type of seal was found that gave promising enough operation, as both a shaft and drum seal, to be recommended for installation in prototype wet-head machines.

Jan 1, 1975

The patterns of occupational health pro- grammes in mining and metallurgy are discussed in relation to the impact of chemical and phy- sical hazards on the health of workers in these fields. Mining and metallurgy are quite unique in that their history and practice embrace virtually the total spectrum of occupational health problems and hazards as understood today. A panoramic concept of the possibilities would comprise the following fields: 1. The Pneumoconioses or Dust Diseases. 2. Physical stress due to exertion, and exposure to heat and humidity in deep mines. 3. The toxic effects of various metals in the mining of ore. The most obvious are lead, mercury, arsenic and manganese. 4. Diseases associated with mining. These include leptospirosis, ankylostomiasis and mycotic infections of the skin. 5. The Beat Diseases of coal miners working in narrow seams. 6. Illumination problems and miners nystagmus. 7. Geographical and climatic problems

Jan 1, 1975

By Thomas F. Torries, George H. K. Schenck

Crushed and broken stone is used directly in construction as an aggregate and accounts for about half the value and two-fifths of the quantity of natural aggregates consumed in the United States. Sand and gravel provide most of the balance of aggregates except for some lightweight materials such as pumice and expanded shale. Conditions necessary for production of crushed stone from a deposit are : 1) Quality-should pass rigid specifications for strength and durability. 2) Cost-low average total delivered cost. Construction aggregates are hard, essentially inert materials suitable for being formed into a stable mass either (1) by the addition of cementing or binding materials that produce a concrete or (2) by compaction or by natural weight to produce a road base or foundation. Aggregates usually provide about 80 to 100% of the material volume of the construction masses in which they are used. The construction industry utilizes as aggregates about 70% of all crushed stone produced in the United States according to statistics provided by the U.S. Bureau of Mines (USBM) , [Table 1], using definitions as shown below. Nonconstruction uses of crushed stone, [Table 2], are included elsewhere in Industrial Minerals and Rocks because such uses require the special physical or chemical characteristics which are discussed in those chapters.

Jan 1, 1975

By Charles H. Jacoby

In 1774 a Swedish chemist, C. W. Schule, first recognized manganese as an element. That same year Schule's associate, J. G. Gahn, isolated the element manganese for the first time. In 1856 the Bessemer process of steelmaking gave birth to the economic importance of manganese. Later, in 1882, Robert Hadfield discovered high manganese steels. Although the primary use of manganese is in the ferroalloy industry, two additional important uses for manganese are making chemicals and dry cell batteries. Manganese is also vital to plant and animal life. Various chemical compounds of manganese are used in fertilizers, feeds, glass manufacture, paints, varnishes, and for numerous medicinal and chemical purposes. For the study of industrial minerals and rocks, only the chemical and battery grade material is of concern, but for the sake of comparison, metallurgical aspects are included in this presentation. Although currently the world's largest consumer of manganese, the United States is producing only minor amounts of ore at the present time. This is due primarily to the fact that although huge deposits of manganese occur within our borders, all are of such low grade as to be economically unfeasible to mine. For many years various government agencies and segments of private industry have devoted sizable sums of money and time in an attempt to upgrade ores from the various deposits, and also in an attempt to recover manganese from blast furnace slags. In view of current world prices, and the quantity of high grade material available, there is little likelihood that any of these approaches will be found to be economically feasible in the near future. Geology and Mineralogy Mineralogy There are over one hundred minerals that contain manganese. These minerals vary from those with compositions that are predominantly manganese to those having only minor percentages. [ ] Geology From a geological standpoint most manga¬nese deposits are complex. In general, it can be said that all primary deposits of manganese are carbonates or silicates. The most productive and profitable have been those of sedimentary origin and residual concentrations. Examples of these residual types of deposits are associated with the metamorphosed lodes of Madhya, Pradesh, India, and the lateritic deposits of Orissa and Bihar, India; nodules in the residual clays of the Philippine Islands, U.S. southern Appalachians and Arkansas, Ghana, and Brazil. Sedimentary manganese deposits are best exemplified by the Nikopol district of Russia and the Tchiatouri area of Georgia, USSR. Hydrothermal replacements are characterized by the rhodochrosite deposits of Butte and Phillipsburg, Mont. In general, the hydrothermal type deposit has not resulted in any large tonnages being produced, but may have given

Jan 1, 1975

By James F. McConnell

Federal and State sulfur oxide emission and ambient air quality regulations have been implemented to fulfill the requirements of the Federal Clean Air Act Amendments of 1970. Primary and secondary air quality standards have been established at levels considered necessary to assure the protection of the health and welfare of the public. Standards of performance under this Act have been established to control the rate of sulfur oxide emissions from individual sources so as to protect and to improve the quality of the Nation's air. The new source standards of performance were made rigorous for large coal burning stationary sources. This has had a severe impact on the electric utilities that operate the coal fired steam electric plants which are the largest consumers of the Nation's coal production. States have taken different approaches in State Implementation Plans (SIPS) as approved by the Federal Environmental Protection Agency. Some states, such as Pennsylvania, have chosen to permit moderate SO2 emission rates from existing sources which are not in critical air basins. All are required to meet primary and secondary air quality standards and to limit sulfur oxide emissions from new large stationary sources to a minimum of 1.2 LBS of S02/MMBTU fired. This re- quires a fuel sulfur percentage of about 0.7 for a 12,000 BTU/lb coal. In an effort to develop strategies and technologies to conform to performance standards while continuing and hopefully expanding the utilization of the Nation's coal supply, the electric utilities, the Federal and State regulatory agencies, and other industries and government agencies are considering several alternatives. 1. Natural low sulfur coal 2. Flue gas desulfurization - (FGD) non-regenerative and regenerative 3. Coal gasification 4. Liquefaction and solvent refined coal 5. Fluidized bed combustion 6. Chemical coal cleaning 7. Physical coal cleaning Of these options, only the first and the last can be considered to be widely used in full commercial practice at this time. FGD has certainly demonstrated technical and operating feasibility and is close to being in full commercial practice but it remains to be seen if the large systems under construction are economically and environmentally optimum.

Jan 1, 1975

By Thompson IR

This paper describes a Client Consultant Relationship and shows how an engineering team created an environ- ment which fosters the development of good, economical and sometimes unique solutions. A major factor in establish- ing this environment was the Client's instruction to the Consultant to "propose solutions which, in the Consultant's considered opinion, best satisfy the needs of the project - not necessarily solutions which reproduce methods adopted elsewhere in the past." The Consultant's experience in other projects and disciplines outside mining has contributed by providing a cross- fertilisation of ideas. The team approach also allows the Client's expertise to be applied positively throughout the design process. These factors and the Client's foresight in providing adequate time for planning, allow the Client-Consultant Team to apply sound fundamental engineering in developing effective solutions.

Jan 1, 1975

By Thomas V. Falkie

Of the various critics of federal energy and minerals policy we are hearing these days--and they are legion--few make their points more vividly than our fellow SME member and eloquent spokesman for the mineral industry. Mr. Eugene Guccione. In a moment of comparative mellowness. Mr. Guccione recently characterized Washington's time-honored legislative and bureaucratic machinery as a case of "...scientific illiterates asking the incompetents to do the unnecessary." I hope the prevailing industry view of government is not quite that harsh, and yet one cannot deny that government intervention is indeed pressing in on the mineral industry with increasing force. What is happening today in Washington and in state capitols will have enormous impact--both short and long term--on the future of coal and mineral production in the United States. Symptoms of this trend are everywhere. In the first place, there is a sentiment, widely held and still spreading, that the government must become involved-- that no matter what the problem, the solution lies in more government intervention. Free enterprise versus statist, reflex reaction organizations. When it cones to regulation in the resource field, there is too often a tendency to start out by assuming guilt on the part of the mineral industry. This can lead to laws governing mineral recovery that are more punitive than constructive...laws drawn up with little research into the scientific or economic considerations involved.

Jan 1, 1975

By R. V. Ramani, C. B. Manula, A. Owili-Eger

ANALYTICAL PRESSURE - VOLUME COMPUTATIONS FOR THE MINE PROTOTYPE A new coal mine is projected, with entrance by slope 1,500 feet long. Nine main entries will be standard for development, five as intake and four as return. One return shaft is planned near the slope bottom, and an intake shaft and portal are planned 5,000 feet north of the slope bottom. The slope will have an area of 150 square feet and a perimeter of 55 feet. A belt and supply track will be within the slope. The return shaft will be circular with a diameter of 18 feet and will be 500 feet deep with an escapeway. Two hundred feet of the shaft and 500 feet of the slope will be concrete lined. Select the fan to operate five units per shift and drive the 5,000 feet to a proposed new portal, using the slope for an intake. Two main splits are planned with the maximum of three units on any split. The amount of air desired at each unit is 25,000 c.f.m; a shop at the slope bottom will require 10,000 c.f.m. In the solution of this or any similar problem, the first step is to determine the resistance factors. CALCULATION OF R FACTORS Slope area = 150 sq. ft.; Perimeter = 55 feet; Length = 1,500 feet. The friction factor K must be established. Five hundred feet of the slope is smooth lined, moderately obstructed by belt; K = 35. The remaining 1000 feet is in sedimentary rock and moderately obstructed; K = 85.

Jan 1, 1975

By Ellis WK, Greenwood-Smith R

A nuclear technique for the analysis of copper in bulk materials has been developed and successfully field tested at Mount Isa Mines Limited. The technique utilises the gamma-ray resonance scattering process. A bulk analyser based on this technique gives a rapid and accurate measurement of the percentage by weight of copper or nickel aver- aged over a large mass of sample, typically 20 kg. The only sample preparation required for accurate analysis is crushing to -2.5 cm. At Mount Isa over 100 mineral samples covering a wide range of rock types and copper contents were analysed. Bulk analyser assays and chemical laboratory assays agreed closely for underground pillar-extraction and geolog- ical chip samples, conveyor belt samples, and finely ground samples from the ore concentrator. For the concentrator samples, the root mean square deviation between bulk analyser and chem- ical laboratory assays was 0.06 wt.% copper. The chemical assay errors for these samples were about 0.06 wt.%

Jan 1, 1975

By James W. Jensen, Aarne Visnapuu

Experimental modifications have been made by the Bureau of Mines on standard pneumatic rock drills to reduce the noise of the air exhaust, drill steel resonance noise, and noise radiated by the drill body. A close-fitting case and muffler around the drill body, consisting of a metallic honeycomb skeleton filled with viscoelastic absorber on the inside and a durable outer shell, provide both exhaust and drill body noise muff ling and absorption. Drill steel resonance noise is reduced by a constrained-layer treatment consisting of a tubular metal cover bonded to the ouside of the sod by a viscoelastic filler. Damping alloy components have been developed to reduce metallic resonance noise. Combined, these modifications have reduced the drilling noise level in granite from 115 dbA to 97 dbA. Data are presented on the individual and combined effects of these modifications on drilling noise and performance.

Jan 1, 1975

By D. J. M. Grodzian

Polymorphic transformations taking place in grinding processes, of massicot to litharge in PbO system, and of y to a in Fe203 system, were re-investigated. Grinding was carried-on in a steeel rotation mill charged with WC balls, under inert atmosphere. The kinetics of transformation in PbO was established by means of quantitative X-ray diffraction analysis. The resulting data fit a modified logistic growth function up to about 75% of transformed volume fraction, when a mixture at steady-state equilibrium is formed. The reasoning for the use of a modified logistic function is discussed. A sigmoidal growth function can be used if resulting data fit also an empirical power relationship between transformed volume fraction and time. However, it lacks the significance expressed by a modified logistic function. Assuming, the loss in magnetism is directly related to the amount of transformation in Fe 203, a quantitative analysis was performed using a magnetic balance method. The results fit only the modified logistic growth function, and transformation proceeds almost to completion. A wide literature survey of the subject is given. Available data from literature is compared with the results of the present study, and is shown also to fit a modified logistic grown function, with surprisingly similar slpes in a linear plot, independently of the material. The instrumentation effect on kinetics parameters, and the establishment of equilibrium mixture values, are discussed.

Jan 1, 1975

HISTORY OF PROCESS DEVELOPMENT The manufacture of coke from coal commenced at the beginning of the 17th century by heaping coal into circular mounds in the open, covering with earth, clay or ash and slowly burning the coal in the mounds to produce a heap of coke. Naturally the process was slow in production rate with low coke recovery due to the loss of that part of the coal which was completely burnt to ash. As a natural consequence of this initial carbonisation method, a coke oven design was developed so that the coking chamber, which was constructed of brick, was circular in plan, cylindrical in section with a dome shaped roof - similar in shape to the original coal mounds. As the shape of the chamber was similar to the old dome shaped beehive, the ovens were called beehive ovens. The ovens were built in long single or double rows with retaining walls between each oven and as such were known as a battery of beehive coke ovens. In these early beehive ovens, coal was charged from hand wheeled tubs into a hole into the top of each oven, hand- levelled with a rake and the oven side opening sealed with bricks and clay except for some small holes in the opening to admit limited quantity of air for combustion. Coking commenced by the heat retained in the brickwork from the previous charge. The gases evolved from the coal, together with the admitted air, were partially burnt inside the oven to supply the heat for carbonisation and the surplus gases were burnt to waste at the top charging hole. The heat from this gaseous combustion inside the oven together with the reflected heat from the brickwork of the arched roof of the oven allowed carbonisation of the coal charge to proceed from its surface slowly downwards to the floor of the oven. At the end of the coking cycle (usually 4 or 5 days) when there was no more evolution of gases, as indicated by diminishing gas flame and a drop in oven temperature, the brickwork of the oven opening was removed. The coke was then quenched by inserting a pipe with spray holes to spray water over the coke charge in the oven after which the coke was raked from the oven. The work of charging and levelling the coal, bricking and removal of oven opening, quenching and raking out the coke all required manual labour. As these ovens only carbonised a 5 to 7 ton charge of coal per cycle of 4 to 5 days, to produce 3 to 41/2 ton of marketable coke, the labour required per ton of coke was high.

Jan 1, 1975

By L. John Minnick

Extraction of crude ores and minerals inevitably produces various by-products either as a result of nonusable residues or as waste by-products from process operations. Thus for each 100 tons of coal extracted in a strip mine operation, one can expect to produce 25 tons, or more, of mine refuse. In addition, the amount of ash produced from the burning of coal will represent 10 to 20 percent of the weight of coal burned. With the advent of lime/limestone scrubbers now being installed on many power plants, an additional by-product is produced that in most instances is equal in volume to the sluiced fly ash. Statistics developed by the National Ash Association have indicated that sluiced waste from power plants in the United States currently exceeds 25 million tons per year (dry basis). Overall mineral industry statistics (copper mines, etc.) indicate better than 200 million tons per year. In the past it was general practice to send most of these waste materials to holding ponds or lagoons simply as a means of disposal or "throwaway" of unwanted by-products. Unfortunately modern society has reached a stage where these large quantities of waste materials are creating monumental environmental and economic problems that need urgent attention. Among these problems are concern for loss of future usable land, pollution of ground water, loss of potential mineral reserves, and loss of opportunities to recycle or use these by-products for the benefit of future generations. An example of the latter is the serious shortages of construction quality aggregates that can be replaced with some of the by-products produced from waste materials from the extractive and chemical industries.

Jan 1, 1975