Search Documents

By Peter N. Calder

The selection of a slope angle for an open pit in rock has often been made without the benefit of a comprehensive engineering study. This is largely due to the fact that the hardware and procedures necessary for such a study have not been available. Recently this situation has been reversed. The application of borehole television and terrestrial photogrammetric devices has made possible the accurate determination of rock joint structure, on which stability calculations can be based. Another important aspect is the evolution of practical methods of conducting in-situ rock joint strength tests.

Jan 1, 1971

By R. R. Montigny

A brief description is given of the history, location and geology of the Granisle Copper Limited operation on Copper I land in Babine Lake. Detailed information is given with regard to pit design, planning, drilling, blasting, excavation and haulage. Equipment maintenance and mining costs are also presented.

Jan 1, 1971

In his introductory remarks Mr. MacKellar referred to three types of development which may be considered to compete with mining for land use. 1. Total Development - in which he cited urban development, and intensive agriculture. 2. Partial development - in which he cited pastoral, and in this category would come National Parks. 3. Non development - in which category would fall the primitive or wilderness areas.

Jan 1, 1971

By Ralph B. Adair

The Bureau of Mines conducted laboratory batch and small-scale continuous tests on samples of silt from the Nolichucky Reservoir near Greeneville, Tenn., to develop a process for the recovery of commercial-grade muscovite concentrates. Using a combination of Humphreys spirals for preconcentration followed by cationic flotation, 94.5 percent of the muscovite was recovered in a product containing 96.5 percent muscovite.

Jan 1, 1971

By Richard Chojnacki

The western united States is not usually noted for the production of fluorspar; however, many significant fluorspar districts do occur in the Rocky Mountain region and constitute a resource of sizable dimension and major potential. This is particularly true within the area of the West served by the rail lines of the Union Pacific Railroad (see Figure 1). Fluorspar deposits near the Union Pacific have produced over 1.3 million tons of finished fluorspar products from 2.3 million tons of ore. Approximately 80% of this production was of acid-grade and 20% of metallurgical-grade fluorspar. Production of ceramic-grade was negligible. Through the years substantial production has come from eight mining districts. Five of these have produced metallurgical-grade and three acid-grade. The best-known fluorspar producing area in the West is the Jamestown Mining District. It was one of the first producers of fluorspar in the western United States and is estimated to have produced over 500,000 tons of finished fluorspar from over a million tons of ore. The district encompasses approximately 36 square miles in central Boulder County, Colorado, about 9 miles northwest of the City of Boulder. Although small shipments were made from the district as early as 1873 or 1874, significant sustained production was not achieved until 1940 when the General Chemical Company, now a division of the Allied Chemical company, acquired the Alice, Burlington, Chancellor,

Jan 1, 1971

By R. L. Rough

Photoelastic, wire resistance, and borehole-deformation gages were used to measure the in situ strains when an outcropping Black Hand Sandstone Formation in Hocking State Forest, Hocking County, Ohio, was overcored to stress-relieve the surrounding sandstone. Strains transmitted to the photo-elastic gage did not produce isochromatic patterns suitable for quantitative analysis. Strain readings from the wire resistance gage indicated tensile-strain loading during overcoring; readings from the strain-gage bridges in the borehole-deformation gage indicated compressive-strain relaxation during overcoring. The magnitude and orientation of the computed stress fields obtained from both gages were comparable when the corresponding tensile and compressive elastic moduli were applied. Stresses computed from deformation and resistance gages at depths to 5 feet showed the maximum stresses to range from 1.042 to 2.121 times greater than the minimum stresses. The bearings of principal stresses calculated from the deformation gage readings varied between N 61° E and N 83° E; the wire resistance strain gage bearing computations varied between N 68° E and N 82° E. Measurements of in situ strain in sandstone were shown to have promise but to require further development in field technique that could likely be achieved through experience.

Jan 1, 1971

By Robert V. Whitman

INTRODUCTION Ideally, this paper should start by citing examples of slope failures in open pit mines during earthquakes. I do not know of any such examples, although - since my search of the literature has not been exhaustive - such examples may well exist. However, there certainly are many examples of devastating earthquake-induced landslides, and there is no reason why such landslides cannot occur at large open pits. Moreover, many of the actual earthquake-induced landslides have seriously affected mining operations in one way or another. Hence, this paper will treat earthquake-induced landslide phenomena in general, in the hope and expectation that the reader can apply this general knowledge to the specific problems associated with open pit mining. Ultimately, of course, the aim is to predict the likelihood of the occurrence of earthquake-induced landslides, and to delineate steps which can be taken to minimize the possibility of their occurrence. These aims can be achieved only imperfectly at the present time, for our knowledge concerning earthquake-induced landslides is still in an embryonic stage. Nonetheless, much useful knowledge does exist. In order to understand and apply this knowledge, it is necessary to: 1. Review the nature and extent of actual earthquake-induced landslides; 2. Have a grasp of the basic terminology and concepts of seismology; 3. Study the fundamentals of probability-based seismic risk analysis; 4. Appreciate the way in which earth materials behave during earthquake loadings; and 5. Have a general knowledge of the methods currently available for analyzing the dynamic response of slopes. Much of this paper is devoted to this necessary background. Information of practical use in connection with various classes of slope stability problems is assembled in the final sections. LANDSLIDES DURING PAST EARTHQUAKES Almost every earthquake in mountainous country, strong enough to be reported in the literature, has caused at least some landslides and rockfalls. Unless these slides or falls damage

Jan 1, 1971

By Y. Okahara, I. Iwasaki

Chlorination behaviors of pure iron and manganese oxides were investigated by combining a thermogravimetric analysis (TGA) technique with batch-boat roasting followed by leaching. Ferrous and manganous oxides could be chlorinated readily, but, in the absence of a reductant, the higher oxides of both iron and manganese were dificult to chlorinate. Thermogravimetric analysis curves were drawn to illustrate the complexities of the reactions, and the possible mechanisms were discussed. Then three manganif-erous materials from the Cuyuna Range of Minnesota were treated by a process involving the selective chlorination of manganese followed by leaching. The results were interpreted in the light of the chlorination mechanisms observed on the pure iron and manganese oxides. One of the unsolved problems challenging Minnesota's mining industry is the development of an economic process to utilize the manganiferous iron ores of the Cuyuna Range. Although these ores constitute one of the major domestic reserves of manganese (estimated at 432 million tons'), their grade is too low for them to be mined solely for manganese. The nearly exclusive dependence of the U.S. steelmaking industry on foreign manganese ores has stimulated research over the years in treating the low-grade Cuyuna ores. As a result, a number of processes have been proposed.'-' Among these processes is chlorination. Chlorination is the high-temperature conversion of metallic oxides to chlorides by either chlorine or hydrogen chloride gas, or by solid chlorides of sodium, calcium, or magnesium. The metallic chlorides are then recovered by either vaporization or leaching. Although chlorination is an old art, it has become popular in recent years for the recovery of such new metals as titanium, zirconium, and niobium; for the removal of impurities like copper, lead, and zinc from pyrite cinder for ironmaking raw materials;' and for the segregation roasting of coppera and nickel' ores. The chlorination processes proposed for manganifer-ous iron ores have been relatively few (hydrogen chloride chloridization-leaching, hydrogen chloride and calcium chloride chloridization-volatilization,' and chlo-rination-selective condensation6), due presumably to the economics and to the corrosion problems involved. However, the successful application of chlorination processes to other ores will undoubtedly contribute to technological advancements in the chlorination of man-

Jan 1, 1971

By Robert S. Shoemaker

The development of a metallurgical project is a business venture rather than a technical exercise, and its real objective is to obtain the maximum return on investment consistent with the limitations imposed by company policy and the requirements of society. Demand for profits is the driving force for technical advances and naturally leads to improvements in processes, equipment and plant designs. In the mineral dressing field there have been virtually no new processes developed since the introduction of flotation, and the steady erosion of profits by inflation has been offset only by increasing equipment size. Unfortunately, in recent years, plant designers have not always utilized the largest equipment or the opportunities for functional and economic design presented by the development of larger equipment. Lower cost plants can be developed providing that unrealistic restraints arising from the prejudice of past practices are avoided. As an illustration of this premise, three different approaches were taken toward the design of a clearly delineated but hypothetical copper concentrator of 20, 000 tons per day capacity. While the same flowsheet was used in each case, designs were produced for a conventional plant, an alternate using the largest available equipment, and a third scheme utilizing large equipment and the most functional design which could be developed, including features derived from many plants in many different industries. Capital costs were developed for the three separate designs based on a location in the southwestern United States. Ancillary facilities were identical in each case and included a mine truck shop, a maintenance shop, a general office, and a nominal starter dam for tailings disposal within 5000 feet of the plant. Water supply within 1000 feet of the plant, and power furnished to the property boundary has been assumed in each case. The flowsheet of the three plants is shown in Figure 1 and represents the treatment of a typical sulfide copper ore by three- stage crushing followed by single-stage ball milling. Concentration is by flotation roughing and scavenging followed by regrinding of the concentrates and two stages of cleaning.

Jan 1, 1971

By H. A. Dierks

The work and costs involved in controlling three large fires in abandoned mines in the anthracite region of Pennsylvania are presented in detail. The work was done under authority of Public Law 89-4. Three basic control techniques were successfully employed by the Bureau of Mines: (1) forming underground fire-containing barriers by systematically flushing incombustible material into mine voids, (2) excavating an isolation trench around the fire area, and (3) complete excavation of hot and burning material in the fire area. When methods 2 and 3 were used, the excavations were subsequently back- filled with incombustible material. Preliminary location of fire perimeters by the standard use of patterned 6- and 8-inch-diameter boreholes is discussed. Investigations into air-borne infrared scanning, shallow subsurface thermal anomalies, and the use of helium to trace the movement of mine air currents are covered. Although they are costly and time consuming, boreholes have proven to be the most efficient means to date of obtaining necessary subsurface fire data. Infrared scanning was ineffective in delineating fires under more than 30 feet of cover. Helium-tracing was shown to have a good potential for determining possible hazards to adjacent residential areas from traveling mine fire gases.

Jan 1, 1971

A digital computer program has been developed to mathematically simulate the effect of limited changes in feed rate on the grinding circuit of an operating mill. The data on which the program is based was supplied by the staff of the mill in question. Samples taken around the complete grinding circuit were analyzed for solids content and particle size distribution for two feed rates. Matrix models were used to represent the grinding units: rod mill and pebble mills. Parameters for these models were computed using a method developed by Mular(l). Classifier parameters were computed by the Powell search method(2) for the Plitt model (3) . The simulation program, which permits the computing of the size distributions in the circuit resulting from the changes in feed rate between the two measured values, assumes that a linear relationship exists between the corresponding parameter coefficients. The program uses an iteration method to bring the simulated grinding circuit to a steady-state material balance for any specified' feed rate between those measured. The program is, in addition, extremely fast and economic in computing time. The results show that the simulations are not everywhere consistent with practice. For example, higher feed rates on simulation predict finer products. These errors are shown to be attributable to anomalies in data gathering techniques. An improved sampling procedure for grinding-circuit data gathering is suggested for future simulations of this type. It is concluded that the

Jan 1, 1971

By A. Sobering, G. N. Carlson

"This paper describes the conversion of the grinding section of the W a bush Mines pelletizing plant from conventional wet, open-circuit trunnion overflow ball milling, with filtering, and bentonite mixing on a common conveyor belt, to dry, open-circuit, grate discharge grinding, with pug mill mixing of bentonite and water at individual mills.The test work and data on operating economies to justify the cost of conversion are given. It is too early, at the time of writing, to have complete operating confirmation, but data are available. A brief description of the original plant is included."

Jan 1, 1971

By H. E. Blake

An evaluation was made to determine the economics of utilizing waste fluosilicic acid for production of (1) calcium fluoride, and (2) anhydrous hydro-gen fluoride. Two versions of each process were considered and compared. The evaluation showed that both products could be produced and marketed competitively. Lowest estimated product sales prices required to yield a 25-percent return on investment before taxes (discounted cash flow basis) was $339.34 per ton of hydrogen fluoride and $48.64 per ton of calcium fluoride.

Jan 1, 1971

By D. S. Flett, A. W. Fletcher

Equilibrium studies on the extraction of nickel and cobalt with kerosine solutions of naphthenic acid have shown that an exchange extraction reaction occurs at pH 5.5. The nickel/cobalt separation factor is constant at 1.8 for constant total metal molarity and varying nickel/cobalt ratios. The separation factor decreases with increasing total metal molarity in the organic phase beyond 0.2 M and also decreases with increasing temperature. From the equilibrium data, it has been possible to derive a mathematical model for the separation of nickel from cobalt by exchange extraction in multistage systems. Experimental data from a continuously operated multistage mixer/settler apparatus has shown a reasonable correspondence with computer-calculated data. The effective separation of nickel and cobalt in sulfate solution remains a problem in hydrometallurgy and the hope that this would be solved by solvent extraction has not yet been fulfilled. With chloride solutions, advantage may be taken of the ability of cobalt to form anionic complexes with the chloride ion. It can then be readily separated from nickel, which does not form stable chloro complexes, by extraction with a suitable long chain amine. However, in hydro metallurgical operations, sulfate solutions are generally obtained in which no extractable anionic species are present. Thus, the possibility of using cationic extractants must be considered, and in this paper attention is directed to the use of carboxylic acids. The method of separation studied has been termed exchange extraction, which involves replacement of a metal in the organic phase with a more acidic metal in the aqueous phase. Thus, (BR2).+ (Az+)aqt=(AR,).+ (B2+)aq (I) where metal A is more acidic than metal B, R represents the acidic radical derived from the acid RH, and the subscripts e and aq refer to the organic and aqueous phases, respectively. Ashbrook and Ritcey' have used this method for the separation of cobalt from nickel using the sodium salt of di-2 ethyl hexyl phosphoric acid, which preferentially extracts cobalt. Some nickel is coextracted, and this is removed by exchange with cobalt ions in the feed solution by suitable countercurrent operation in a pulsed column. Much work has been carried out by a number of workers in Russia on the general use of exchange extraction for the separation of metal ions using car-boxylic acids. Gindin et aL a have demonstrated that this technique could be applied to the separation of nickel from cobalt using a C--C. carboxylic acid and have applied the technique to the production of high purity cobalt solutions for electrolysis. Further worka was concerned with the development of a process for the separation of nickel from cobalt in a pulsed column. This system permitted the separation of iron and copper from nickel and cobalt in one system. The procedure involved center feeding with acid backwashing at the top and alkali addition lower down the column. Thus the system operated under a pH gradient and the metals were distributed in the column in the order of their basicities. A similar application was studied by Gel'perin et al,4,5 for the removal of copper and iron impurities from a nickel anolyte by means of a C10-C,12 fatty acid fraction. Ginden et al,' and Fletcher and Wilson' have studied the effect of pH on the extraction of a number of metals with carboxylic acids. These studies showed that metals such as iron, copper, lead, zinc, nickel cobalt, and manganese are extracted at pH values close to the pH of hydroxide precipitation. Nickel is extracted at a slightly lower pH than cobalt and thus the nickel/cobalt separation factor has a value not much greater than 1. More basic work on complex identification has been reported by Fletcher and Flett: by Tanaka; and Jay-cock and Jones." These studies have suggested that at low loadings in the organic phase, the nickel and cobalt carboxylates appear to be dimeric and solvated by free carboxylic acid molecules. As the concentration of metal in the organic phase increases, the complex changes and larger polymeric species are formed. In order to permit assessment of the potential of carboxylic acids as extraction reagents for separation of

Jan 1, 1971

By Hulbert A. Lee

"A REVIEW OF MINERAL DISCOVERIES IN CANADA, and in particular the Canadian Shield, using the physical aspects of overburden reveals a trend in the art of exploration. At an early time of exploration (1847-1954), float and heavy clasts were used successfully to find ore deposits with little knowledge of Quaternary environments. At a later time (1955 to present) , use of Quaternary rock-units for sampling have made possible tracing indicator trains of float, heavy clasts and other ore-type clasts to the source bedrock. The basal till of retreat ice is now recognized as a1l favourable sampling environment and as such has been used to successfully discover hidden orebodies. The esker massive gravel is beginning to be recognized as a favourable environment and use of it has met with technical success. An understanding of those changes that have taken place during the transportation of the material and after its deposition is essential to proper sampling and treatment of the samples from the basal till and the esker massive gravel. Use of float and heavy clasts in search of orebodies is continuing in present-day exploration on the Shield. Lessons learned from it are being incorporated into exploration using favourable Quaternary rock-units for sampling. Hence, both subjects have a need for review and are discussed in this paper."

Jan 1, 1971

By M. C. Fuerstenau

Each year during the AIME Annual Meeting, the MBD Division has its Business Meeting. Because many members cannot attend, it has be- come policy for the secretary of the Division to present highlights of the business conducted at the Meeting in Fine Grind. This year the Meeting was held on March 1 in the Americana Hotel. Five major items of business were brought up for discussion. These were: (1) the proposed name change for the Division, (2) institution of the Taggart Award, (3) a name change for a Unit Committee, (4) MBD funding of scholarships, and (5) authorship of Fine Grind articles. The Matter of What We Should Call Ourselves A lively discussion was held on the issue of a name change for the Division. Two names have been proposed: (1) Mineral Processing Division, and (2) Mineral Engineering Division. A number of strong reasons for changing the name from Minerals Beneficiation Division have been pointed out. Perhaps the most important of these is that the term "beneficiation" does not describe all of the functions that engineers in our Division perform. Further, there are inherent problems associated in the term, in that beneficiation is a long word which has the twofold disadvantage of being both difficult to pronounce and difficult to spell.

Jan 1, 1971

By Thys B. Johnson

A three-dimensional dynamic programing method is presented for determining the optimal ultimate open pit limit. The method given is based on the block concept and is an extention of the two-dimensional Lerchs-Grossmann approach. The three-dimensional technique presented herein is fast and simple and may be used for an initial open pit evaluation when only limited data are available or as a more refined model when the entire deposit is well delineated. The method is illustrated by simple numerical examples and is also presented in algorithmic form. A computer program was written in Fortran IV which implements the three-dimensional algorithm and some computational aspects are discussed.

Jan 1, 1971

By Norbert R. Morgenstern

INTRODUCTION An understanding of the role of water in controlling the stability of rock masses is central for a rational approach to the subject. The presence of water can hinder mining opera- tions in two ways: 1. excessive discharge 2. excessive pressure It should be noted that if the rock mass is very tight, excessive pressures can exist without large discharges. Alternatively, if abundant water is available and the rock mass is open, then substantial discharges can occur under quite small pressures. The problems associated with excessive discharge are usually well understood by the mining engineer. Vehicle mobility is inhibited, some areas are flooded and hence become inaccessible; at best, a costly nuisance exists. The methods of solving these problems are also well-known to mining engineers. They generally involve tapping the source of the excessive discharge and channeling it away in such a manner that any hindrance to the mining operation is minimized. The effects of water pressure on the stability of rock masses are less obvious and the following will be devoted solely to this aspect of the problem. The manner in which water pressures enter into the consideration of stability is made clear by an understanding of the concept of effective stress. THE CONCEPT OF EFFECTIVE STRESS The simplest mechanical model for the problem of rock slope stability consists of a rough, rigid block sliding down an inclined plane under the influence of gravity. This is illustrated in [Fig. 1]. The down-slope component of the weight of the block tends to produce movement which is resisted by the shearing force generated by friction along the base of the block. The shear stress per unit area inducing movement is

Jan 1, 1971

By J. Grumer

Nine dust and gaseous inhibitors of propagating coal dust-air flames (lean, stoichiometric, and rich) were evaluated in a newly developed 15-cm-id, 3.6-meter-long instrumented flame duct, under conditions such that wall quenching was virtually absent and the dust concentration was temporally and spacially uniform to within about t5 percent. Listed roughly in order of increasing efficiency, the inhibitors evaluated were rock dust (calcium carbonate), powdered oyster shells (calcium carbonate), Halon 1301 (trifluorobromomethane), Halon 1211 (difluorochlorobromomethane), sodium chloride, Super-K (potassium chloride), regular-grade fire extinguishant powder (sodium bicarbonate), Purple-K (potassium bicarbonate), and Monnex (potassium bicarbonate combined with urea). Experiments were extended to clouds containing 1 and 2 volume-percent of methane. The inhibition of lean, stoichiometric, and rich methane-air flames without coal dust was also examined in a few instances; results agreed with those obtained for coal dust-air flames.

Jan 1, 1971

Previous methods for measuring the flow of solids in Jnrdraulic conveying have not considered the important effects of slip velocity and particle concentration. In this paper an extension of the method proposed byShirato et al. (J. Chem. Engng. 'Japan, 1: 164-167) for determining mass flow in a vertical conduit is outlined.The present method consists of measuring' the volumetric flow of the slurry (by a magnetic flow meter for instance) and the density of the slurry in two pipe sections of different diameters. Effects of variation of slip withparticle concentration, not previously considered, are allowed.Problems involved in estimating the density of a slurry from differential pressure measurement are discussed.The major problem is the uncertainties in estimating frictional losses due to the wall in two-phase flows. The greater reliability of a more "direct" technique, such as by 'Y-ray absorption, for measuring solid concentration is emphasized.

Jan 1, 1971