Search Documents

By T. E. Scott, O. G. Koepke

DURING research currently in progress the need arose for interplanar angles and planar spacings to analyze crystallographic data obtained from hcp yttrium. In the absence of such existing information, a program was written in Fortran-11 language and processed on an IBM 7074 computer. The program and results have been assembled in report form to make them generally available.' Of the possible combinations of, only those most frequently encountered were employed. The ranges of h, k, and 1 involved were: However, not all combinations and permutations of the above appear in the tabulation because redundancies occur in several cases. Nevertheless, fifteen types of planes and all their equivalent planes have been included, giving a total of 109 sets of Miller-Bravais indices.

Jan 1, 1967

By W. W. Krech, T. E. Perkins

As fractures are propagated through rocks, energy is absorbed near the extending crack tip. Apparent surface energies for several rocks have been measured by cleavage under dynamic con-ditions. At nominal crack velocities from 0.5 to 500 in (min, measurements showed that fractures propagated in discrete jumps. Calculated surface energies and moduli were relatively insensitive to nominal rate of cleavage. in another set of experiments, rocks were cleaved under high confining stresses. The rocks were submerged in low leak-off fluids which formed a filter cake on the freshly cleaved surfaces (similar to the hydraulic lracturing process). Apparent surface energies were increased substantially as the surrounding fluid pressure was increased. Moduli in bending increased significantly upon application of the first 1,000 psi but were insensitive to stress level at greater pressures. INTRODUCTION For almost 20 years, hydraulic fracturing processes have been utilized effectively to stimulate oil and gas wells. During this period, some process improvements have resulted from studies of fracture orientation, mechanics of fracturing, areas generated, conductivities of cracks, etc. Yet many questions remain concerning the conditions and pressures needed during fracture propagation. In this paper we will report additional studies of the mechanics of fracture extension. It was shown previously3 that large rock samples could be cleaved under controlled conditions so as to measure the apparent surface energy (that amount of energy absorbed per unit area of new surface created). In this paper we consider the effects of two additional factors on surface energies, viz.: (1) effect of cleavage rate and (2) effect of confining stress level. THEORY Cleavage experiments were conducted on rock samples similar to that illustrated in Fig. 1. Blocks of rock several inches wide, 2- to 3-in. thick, and up to 3 ft in length were grooved longitudinally with shallow guide slots. A crack was initiated and allowed to extend along the web as the top of the rock specimen was pulled (or pushed) apart. Auxiliary equipment permits the measurement of (1) force applied at the top, (2) separation at the top and (3) crack length. (Further experimental details will be given in the next section.) The rock beams created by the crack are considered ton be cantilever beams. The deflection (or separation of the rock beams) at any point is calculated 4,5 by the beam Eq. 1.

Jan 1, 1967

By N. Mungan

A study was made of the effects of wettability and interfacial tension on the immiscible displacement of a Iiquid by another Iiquid from porous media. The influence of viscosity ratio was also investigated. Porous media used were polytetrafluoroethylene (TFE) cores prepared by compressing TFE powder under different pressures. lt is shown that displacement of a wetting by a nonwetting Iiquid is always less efficient than the displacement of a nonwetting by a wetting fluid, all other things being equal. In the former case, the recovery efficiency can be increased substantially by either reducing the interfacial tension or increasing the viscosity of the displacing fluid. A qualitative discussion is given on the implications of this work to the recovery of crude oil by water flooding. INTRODUCTION The high cost of oil exploration and new recovery schemes makes it imperative that waterflooding be conducted under conditions favoring most efficient oil recovery. To improve oil recovery by waterflooding, it is essential that the role played by interfacial forces in the entrapment of residual oil be studied and understood. Interfacial phenomena in natural rock, connate water and crude oil systems are very complicated because of the complexity of the natural liquids found in petroleum reservoirs, because of our inability to adequately describe the geometrical structure of the porous media and because of a lack of understanding of physical and chemical interactions between the liquids and surface of the pores. The problem becomes further complicated when one tries to elucidate the role of interfacial phenomena in fluid flow. Numerous studies of the displacement of oil by water under different interfacial tension or wet-tability conditions have been made.lm3 These studies have been performed in silica, alundum or sandstone systems using water and paraffin oil and also some surface active material to control the interfacial tension s and the contact angle 0. Unfortunately, the high energies of various interfaces involved favor adsorption and orientation of the surface active material at the interfaces. Also the surface active material concentration at the interfaces exceeds that in the bulk of the liquid phases. Such surface excess may cause the surfactant distribution, the contact angle and the interfacial tension to differ from their measured static equilibrium values and makes interpretation of the displacement experiments difficult. Furthermore, as changes in s also lead to changes in cos 0, the role played individually by one of these parameters in the displacement becomes obscured by the effect of the other. To circumvent these difficulties, a low surface energy solid and true solutions or pure liquids should be used. Use of a low surface energy solid minimizes adsorption and orientation effects at the solid-liquid interfaces. By controlling s and cos 0 through use of selected pairs of pure liquids or true solutions rather than by surfactants, the adsorption effects at liquid-liquid interfaces are eliminated. In the present study TFE cores were used as the porous media. Liquids used were water, sucrose solutions, paraffin oils and benzyl, n-butyl and isobutyl alcohols. The interfacial tension was varied from 40 to 1.1 dynes/cm by suitably choosing the liquid pair. A surface active material was added to the water-oil system only in the case where interfacial tension of 0.5 dyne/ cm was desired. No precise changes of cos 0 were attempted. However, either the displaced or the displacing liquid could be made the one which preferentially wets the TFE surface. Using sucrose solutions and blends of paraffin oils proved to be a convenient way of changing the viscosity ratio between the displaced and displacing liquids. The present investigation examines the effect of interfacial tension, wettability and viscosity ratio on the immiscible liquid-liquid displacement from porous media. Observed data permit a

Jan 1, 1967

By B. E. Eakin, A. L. Lee, M. H. Gonzalez

Expeximental viscosity and density data of lour natural gases are presented for temperatures from WO to 340F and pressures from 100 to 8.000 psia. A correlation is also discussed and results reported. INTRODUCTION This investigation is one of several efforts by the authors to provide viscosity data for pure hydrocarbons and mixtures. Results of some pure hydrocarbons and their mix tures have been presented." Several predictive methods and correlations have also been reported.'," This paper presents the experimental viscosity and density data of four natural gases and confirms a correlation in a previous study. APPARATUS The viscometer was described previously. 2,6 A bank of stainless steel pycnometers was included to determine density in conjunction with the viscosity measurements (Fig. I). DATA AND MATERIALS The natural gases were furnished by the Atlantic Richfield Co. (Samples 1 and 21, the Continental Oil Co. (Sample 3) and the Pan American Petroleum Corp. (Sample 4). Table 1 shows the composition of these gases obtained by mass spectrometer analysis. The pure component viscosity data used in the correlation have been published."".'"', '" Experimental and calculated viscosity data for the natural gases are presented in Tables 2 through 5. CORRELATION Starling and Ellington"' have reported several semi-empirical expressions based to a certain extent on the theory of viscosity advanced by Born and Green.' The final expression presented by Starling and Ellingto'n is: i'. (micropoise) -- /t,, exp rX(7') p ..... (I) Eq. 1 was modified by Lee et 01." to represent mixture and pure component data simultaneously. This equation has the form: F = K exp [XpY] :.........(2) where K=- (7.77 i 0.0063M)Ti 122.4 + 12.9M +T .................(3) ' ' ' X= 2.57 + ---1914.5+ 0.0095M .... (4) Y = 1.11 -r 0.04 X ........(5) Over the pressure and temperature range studied in this investigation, this equation represents the data on methane, ethane, propane, n-butane and four methane-n-butane mixtures with a standard deviation* of ? 1.89 per cent. Density data by Sage and Lacey" were used to fit the equations. Eq. 2 gives reliable values of the viscosity of light hydrocarbons without prior knowledge of experimental viscosity values, but accurate density data must be available. Eq. 2 was used to predict viscosity values for the natural gases studied in this paper. The particular set of parameters contained in Eqs. 3 through 5 gave values that reproduced experimental data within 25 per cent. Needless to say, in using Eq. 2 better density values will give better viscosity results. However, those engineers who do not have accurate density values at hand or the time, or such facilities as a library, computer, etc. readily available, may feel uneasy in using Eq. 2. Therefore, the authors sought the easiest but by no means best density prediction method, which was reported by Kaf 30 years ago. A set of density values, which were calculated based on Kay's method, and a generalized compressibility factor chart were used to fit Eq. 2. The results are:

Jan 1, 1967

By R. G. Davies, R. H. Richman

Several techniques, X-ray diffraction, transmission electron microscopy, conventional, metallography, and mechanical property measurements are combined to investigate decomposition in the suPersaturated solid solution Fe-27 at. pct Be. The following sequence of structures for aging temperatures below 400°C is established: massive short-range order, pseudo-FeBe (L2o) order, Fe3Be (DU3) order, sinusoidal modulation of composition, general or continuous precipitation, and discontinuous or cellular precipitation. In addition to this sequence itself, several features of the individual stages are noteworthy; for example, when coherent modulations occur, their development is parallel to (100) everywhere in the specimen apparently without incubation, and both the wavelength and the composition amplitude of the modulations increase with aging time. Two types of discontinuous reaction are observed, depending upon the aging temperature. At low temperatures (<550°C) the boundary-nucleated variety of discontinuous precipitate predominates; but at higher temperatures (>600°C) the crystallographic variety occurs instead. Hardness and flow-stress measurements clearly reflect the quoted structure sequence. Some qualitative aspects of the structure changes and of the relationship between mechanical properties and structure are discussed. BERYLLIUM in solid solution markedly strengthens iron.&apos;" A recent study demonstrated that not only were supersaturated single crystals of Fe-27 at. pct Be very strong, but they deformed primarily by mechanical twinning.3 Such behavior, coupled with the decrease in solid solubility of beryllium in a Fe from about 33 at. pct at 1165°C to about 10 at. pct at 500°C4 as shown in Fig. 1, leads naturally to questions about property changes with aging in this system. In 1929 roll,1 and later Seljesater and Rogers,5 reported that useful increases in strength could be obtained by aging quenched Fe-Be alloys, but it was not until quite recently that any of the details of precipitation in these alloys were studied. Richman6 observed that both an Fe3Be superlattice (with a DO3 crystal structure the same as Fe3A1, illustrated in Fig. 2) and a modulated structure preceded the appearance of a discrete second phase in the 20 at. pct Be composition. Here, a modulated structure refers to a periodic composition fluctuation within one crystal, while its lattice remains coherent. Subsequent work on a Fe-Be alloys by Heubner7 and von Heimendahl and Heubner8 confirmed the existence of the modulated structure, although only an FeBe (L20) ordered structure was detected (also shown in Fig. 2). Both Rich-man and Heubner corroborated the large increases in hardness during aging reported earlier, but other mechanical properties were not examined. Since modulated systems are encountered relatively infrequently, the influence of coherent modulation upon mechanical properties is not well-known. With the accumulation of information about age-hardening systems, it has become clear that many precipitation reactions cannot always be described by the concept of heterogeneous nucleation at some lattice discontinuity followed by diffusional growth. Rather, complex sequences involving prior "preparation" of the matrix are quite common; that is, a transition structure occurs in the parent phase, instead of in some "nucleus" form. Delineation of such subtle sequences appears to be a worthwhile step toward the understanding of solid-state precipitation. Since not many structural progressions of comparable nature have been reported, the objectives of the present survey are to identify and elucidate the various

Jan 1, 1967

By J. Groyecki, M. Markuszewicz, J. Lassota, A. Zawada

The ratio of stable to unstable inclusions was found to ploy an essential role in the process of sccorldar-y recrystatlizalion in Si-Fe. The analysis of the free energy of inclusions in the range of heat-treatment of individual inclusions to be predicted. The effects MnS. ns inslable inclusions. were investigated. TO secure a high induction, the secondary recryslulliztt-lion associated wilh the texture is necessary. To obtain a low core loss an additional refiuing in the solid state is required. It has been found that sulfur can be more easily removed in racunm than in hydrogen and thai this process was hindered by the prescrzce of INCLUSIONS play an essential role in the development of cube-on-edge texture in Si-Fe. Their function consists in restraining the growth of primary grains up to about 900°C and in passing subsequently into solution at higher temperatures. This process is accompanied by the selective growth of secondary grains with (110)[001] orientation. The general effect of inclusions depends on such factors as the type of impurities, their amount. dispersion and stability, the conditions of diffusion in the space of lattice of metal, and the reactions at the metal/gas interface. In recent years, some of these factors were the subject of a special investigation. A positive influence of Mns, siN,&apos; and vN3 has been established. The quantity of impurities4 and their dispersion5 have been found to be of major importance. Attention was called to the vital importance of diffusion and the conditions under which the impurities are removed from metal., It has also been demonstrated that in Fe-Si alloys by the techniques of powder metallurgy a special opportunity exists to obtain the (110)[001] type texture. 6 The aim of this work was to conduct qualitative investigations on the influence of inclusion stability on the development of cube-on-edge texture in a metal containing approximately 3 pct Si. Experiments were carried out on cast alloys and on those manufactured by powder-metallurgy techniques. The results obtained from these experiments were utilized to explain the phenomena involved and to analyze the relationships between stable and unstable inclusions and the magnetic properties of alloys. EXPERIMENTS AND RESULTS The raw materials used in these experiments were the powder of carbonyl iron with the analysis (in pct) 0.044 C, 0.01 Mn, 0.005 Si, 0.009 P, 0.002 S, traces of Cu, 0.06 Ni, 0.0015 Al, 0.03 Cr, 0.02 Mo, 0.01 Ti, 0.002 Co, traces of Pb, and the powder of silicon containing 94.14 Si, 0.003 S, 0.048 C. The powders were ground and mechanically mixed in 100-g batches. and then pressed at 9 tons per sq cm into 74 by 24 by 8 mm blocks. Sintering was carried out at 1100°C for 12 hr in vacuum (2 x lo-&apos; Tr) or in hydrogen. In this instance the material was heated slowly and subjected to prolonged soaking at 350°, 650°, and 750 2C, respectively, to secure reduction of ferro-oxides. This was checked by making measurements of the dew point, which was found to change from -15" to -35°C after reduction. The compacts after sintering were hot-rolled to 2.4 mm, annealed at 800 C, and finally cold-reduced to 0.35 mm with intermediate annealing at 800°C at a gage of about 0.8 mm. Impurities were added in the powdered form and mixed with iron and silicon powders. Sulfur in the elemental state, electrolytic manganese, and pure aluminum oxide were employed. Besides, to obtain a material with low contents of impurities, especially

Jan 1, 1967

By J. L. Shultz

The Bureau of Mines extended its investigation of methanation catalysts. The noble metals (platinum, palladium, ruthenium, rhodium, osmium) and rhenium), molybdenum, and tungsten were tested in hydrogenations of carbon monoxide and carbon dioxide at 21 atmospheres in a temperature range between 200° and 600° C. From the 8 metals studied) 25 catalysts represent 5 catalyst types were prepared and tested. The impregnated 0.5-percent-ruthenium catalyst proved to be the most active and versatile of all the catalysts produced. Tungsten and the noble metals other than ruthenium were low in activity and usually required temperatures above 500° C for appreciable production of hydrocarbons. Molybdenum was moderate in activity, but further improvement in molybdenum catalysts seems possible.

Jan 1, 1967

By Andrew Cosgarea, William R. Upthegrove, Morteza Mirshamsi

The capillary-reservoir technique was used with lead-210 and cadmium-115m to determine the self-diffiLsion coefficients of both cadmium and lead in the liquid binary Cd-Pb system. The self-diffusion coefficients of pure cadmium and pure lead were obtained and were compared with the theoretical predictions. Good to excellent agrement between the experimental and predicted values was obtained. The self-diffusion coefficients of cadmium were tneasuved in alloys containing 2.50, 9.13, 17.40, 31.00, 45.00, 69.00, and 97.00 lot pct Cd by determining- the amount of cadniiutn-115m which diffused out of a small-bore capillavy into an infinite reservoir during- a given time peviod. Sinzila7-measurements were made with lead-210 to determine the self-diffusion coefficients of lead in these identical alloys. Diffusivities were determined from measurenzents performed in the temperature interval of 290" to 480°C. The results were correlated with the Ar-vhenius equation, and the maximum variation of the equation parameters (Q and Do) was also inrestigated . THE theory of diffusion in liquids, particularly liquid metals, is relatively undeveloped in contrast to that for the gaseous and solid states. Although the practical application of liquid metals as heat-transfer media has become increasingly important, few liquid-metals systems have been investigated. Experimental data of fundamental significance in this field are not readily obtained, which may explain but not justify the present lack of knowledge. What work has been completed is primarily restricted to liquid diffusion of pure metals; little work has been done in liquid-metal diffusion of binary mixtures. A review of liquid-metal diffusion theory and research is available elsewhere.1-4 In an effort to add to the knowledge of liquid-metal systems and to increase the basic understanding of the diffusion process in liquids, a study of diffusion in the binary-liquid system, Cd-Pb, was undertaken. The capillary-reservoir technique5 was employed to measure the self-diffusion coefficients of cadmium and lead in molten binary alloys. Measurements were made with seven selected compositions and over a temperature range from 290° to 480°C. The experimental apparatus consisted essentially of the following items: constant-temperature bath, diffusion cells, capillaries, capillary-filling device, and a radioactive tracer counting system. EXPERIMENTAL APPARATUS Constant-Temperature Bath. A cylindrical steel vessel, 8 in. in diam and 15 in. deep, surrounded by an insulated heating coil was used with a sodium-potassium nitrate salt mixture heating medium. The bath was maintained slightly below the desired control temperature by the furnace-heating element; and a 250-w heater, actuated by a Bayley proportional temperature controller, was utilized for the final control of the temperature. A constant-speed mixer stirred the salt to insure a uniform temperature within the bath. Four calibrated Chromel-Alumel thermocouples were placed at various positions in the salt bath to verify the absence of temperature gradients. The observed temperature variation during any diffusion run was less than 0.l°C. The entire furnace assembly was mounted on four shock absorbers to exclude building vibrations and the stirrer propeller blades were adjusted so not to induce vibrations within the reservoir. A schematic diagram of the furnace and the constant-temperature bath is shown in Fig. 1. Diffusion Cell. The diffusion cells and associated parts were the same, except for slight modification, as the one used by walls1 in this laboratory, and are shown in detail elsewhere.&apos; A graphite crucible, 4 in. long and 40 mm (1-1/2 in.) ID, enclosed in a 60-mm (2-1/4 in.) Pyrex tube cell about 18 in. long, was used as a container for the melt. The reservoir (molten alloy in the graphite crucible) was usually about 2 to 2-1/2 in. deep. Graphite was used because of its satisfactory nature as a refractory material and the low solubility of carbon in molten Cd-Pb alloy.677 The Pyrex cell was closed at the bottom and fitted at the top (open end) with a 2-in. Dresser coupling. A brass flange was welded to the top of the coupling. The upper part of the diffusion assembly was bolted to this flange with an O-ring seal. The lower part of the diffusion cell was supported in a 3-in. brass cylinder which was open to allow for circulation of salt around the cell. The top assembly consisted of two synchronous motors, a drive shaft, a thermocouple well, and controlled-atmosphere inlets and outlets. One motor was used for rotation of the capillaries at a rate of 1/2 rpm in the reservoir during the diffusion run. The other motor was used for the vertical positioning of the capillaries and the capillary holder by means of a simple screw drive. The capillary holder and drive assembly were lowered into the reservoir for the run and raised after the desired diffusion time at a rate of approximately 0.4 in. per min. Capillary holders were made of graphite. These

Jan 1, 1967

By R. E. J. Putman

Rising demand, artificial market conditions, increased overseas competition, and a fluctuating international situation have brought ever increasing pressures to bear on the nonferrous metals industries, and particularly in the United States, Although capacity is being expanded by the construction of new plants and the development of new ore deposits, increasing attention is being focused on the possibilities of improving the performance of the existing installations and of getting the most out of the new equipment now installed. At first sight the task appears formidable. Based on raw materials which are nonhomogeneous, and possessing characteristics which are hard to quantify, even the processes by which the values in the ores are concentrated and extracted are in many cases not fully understood. The necessary analytical equipment and transducers demanded by these industries have also been slow in development and their earlier absence has hampered the application of modern control technology, This is reflected in plants which have been designed for ease of manual rather than automatic control, and in which the application of control techniques at first sight appears economically prohibitive. However, in any industry progress often comes only in small steps, It may be that by the wise choice of limited objectives and perhaps only partial solutions, substantial improvements in plant performance can be implemented now, and with only a modest investment. If modern control equipment is chosen of the type which can be reprogrammed, advantage can be taken later of more sophisticated solutions as the technology of the industry advances. This task of improving plant performance can and must be commenced even though our knowledge is incomplete. The experience of a related mineral consuming industry, with similar problems in the past, can be encouraging.

Jan 1, 1967

By Roy L. Grant

The Bureau of Mines investigated the up-and-down method with factorial designs to determine if shorter, and therefore less costly, trial sequences could be used. Although sequences of 50 trials are usually recommended, sequences of 20 trials were arbitrarily chosen for the experiments with permissible coal mine explosives described in this report. These explosives were fired from a cannon pointed into a flammable natural gas-air atmosphere at the Bureau of Mines Explosives Research Center gallery to ascertain their safety properties. The investigation demonstrated that the shorter sequences led to useful conclusions with a reduction in cost of the experimental program.

Jan 1, 1967

By H. Kreye, E. Hornbogen

An increase in electrical resistivity during aging or after quenching from high temperatures is known in a large number of alloys. Plastic deformation of alloys in this condition leads to a decrease in resistivity. This anomaly has been called the K effect. This effect has been reported in Ni-A1 alloys by several authors.&apos;-4 The nickel-rich solid solution y is in equilibrium with Ni,A1 (y&apos;) with CkAu structure. With this alloy it is therefore possible to produce a homogeneous solid solution as well as a coherent mixture of y and y. The changes in resistivity should be determined for these two conditions. In the present literature on the K effect no distinction is made between them, because of experimental difficulties to determine small coherent particles. In the present work transmission electron microscopy and image formation by (100) and (110) superlattice reflection of the y&apos; phase was employed for a detailed determination of the temperature dependence of solubility of aluminum in nickel and the resulting microstructures with alloys up to 15 at. pct Al. The solubility line follows the equation indicating a smaller solubility than given in the literature at temperatures below 700°C. X-ray scattering was used to get evidence for short-range ordering in the homogeneous solid solutions.5 Parallel to the determination of the microstructure electrical resistivity was measured as a function of aging tempera- ture, time, and aluminum content, which led to the following results: 1) Resistivity increases slightly during aging of a homogeneous solid solution which was quenched from a high temperature as a consequence of short-range order, Fig. 1, curve c,. 2) Resistivity shows a maximum during aging of all alloys which are heterogeneous according to the phase diagram, but which were obtained as a supersaturated solid solution by quenching, Fig. 1, curve c,. The increase in resistivity is mainly due to coherent precipitation of y&apos;. In Fig. 2 the effects due to short-range order pN and due to precipitation of particles APT are shown for an aging temperature of 450°C and different aluminum contents. 3) The increase in resistivity depends on the size !f the coherent particles. A critical diameter of 15 5A for the maximum was found for all alloys and aging treatments by extrapolating particle sizes determined by electron microscopy. 4) The maximum of resistivity of the heterogeneous conditions does not occur if particles, larger than the critical size, have formed already during quenching. 5) Plastic deformation destroys short-range order as well as small coherent particles. Therefore a decrease in resistivity is observed if the increase in resistivity caused originally by these phenomena is

Jan 1, 1967

By J. E. Flinn, S. A. Duran

The steady-state creep behavior of poly crystalline cad mi inn was studied over a temperature range of (1.56 to 0.94 Tm. Two distinct mechanisms were found to occur over this temperature range. They were described by: where and represerqt the minimum strain rates corresponding to the low- and high-temperature regions, respectirely. The two regions of constant acti11ation energy were connected by a transition region where the strain rate was controlled by both mechanisms acting in parallel. At temperatures below a transition temperature of about 0.7 Tm the agreement between the activation energy value for creep and that for self-diffiision suggests a rate-controlling mechanism of dislocation climb. For cadwzium, steady-state creep at temperatures above 0. 7 Tm appears to be controlled by another mechanism, perhaps involving the behavior of dislocation jogs. FRENKEL et al.1 studied the high-temperature creep of polycrystalline cadmium and reported an activation energy of 21 kcal per mole for the 0.5 Tm < T < 0.8 Tm range. Based on observations of creep rate at only two temperatures, a value of 22.1 kcal per mole was determined by Medbury. These two investigations were for the purpose of showing agreement between the activation energy for creep and that for self-diffusion, reported3 as 18.2 and 19.1 kcal per mole, respectively, for diffusion parallel and perpendicular to the hexagonal axis. Gilman4 investigated prismatic glide in single crystals of cadmium over a higher-temperature range of 0.72 to 0.93 Tm, and found an activation energy of 29 kcal per mole. He also reported5 an activation energy higher than that of self-diffusion for prismatic glide in zinc single crystals deformed at temperatures near the melting point. This value was in good agreement with those found for an equivalent temperature range by Flinn and Munson6 and by Tegart and sherby7 for polycrystalline zinc. These two independent studies also disclosed at lower temperatures another value of activation energy near that for self-diffusion. It would be expected from the creep results on zinc and single-crystal cadmium that creep studies on polycrystalline cadmium, extended to temperatures near the melting point, might yield an activation-energy value higher than the 22 kcal per mole value found in earlier studies. The purpose of this paper is to report the steady-creep behavior of polycrystalline cadmium over a temperature range of approximately 0.5 to 0.9 Tm EXPERIMENTAL METHOD The cadmium used in this study was obtained in the form of as-cast rods, 0.5 in. diam, through the courtesy of the Bunker Hill Mining Co. The material was of 99.995 pct purity, as determined by spectro-chemical analysis. The creep specimens, which were 0.250 in. diam by 0.400 in. long and annealed at 300°C for 45 min to produce a stable average grain diameter 0.25 mm, were tested in compression using an apparatus similar to that described by Sherby.8 The specimen temperature was controlled to within ±0.5°C with the help of appropriate constant-temperature baths. The applied stress was maintained within 1.0 pct of the desired value by the additions of lead shot at fixed strain increments. No barreling was observed over the strains encountered during testing. Isothermal creep tests9 were used in the study with only a few differential temperature tests10 run for comparison purposes. Steady-state creep data were obtained over a temperature range of 60 to 287°C (0.56 to 0.94 Tm) at five stress levels ranging from 28.1 to 140.6 kg per sq cm. RESULTS The minimum or steady-state creep rate may be described by an equation of the following form:" where i is the minimum strain rate, S is the structure factor, F is a stress function, Qc is the energy of activation, T is the absolute temperature, and R is the gas constant. The minimum strain rates obtained in this study for cadmium were recorded on a semilogarithm plot as a function of the reciprocal absolute temperatures for the various stress levels, as shown in Fig. 1. This figure shows a characteristic transitional behavior" with a parallel interaction of two mechanisms. It is obvious that the activation energies corresponding to the individual processes are insensitive to stress because the curves are parallel. The discrete activation-energies values for the low- and high-temperature regions for the various stress levels are reported in Table I, and were determined by the least-mean-square method. For the low-temperature region, an activation energy of 20.7 ± 0.6 kcal per mole was obtained, and for the

Jan 1, 1967

By L. R. Woodyatt, H. J. Beattie, C. T. Sims

Theories correlating the formation of u and related intermetallic compounds to the electron-per-atom density of binary and ternary alloys have appeared regularly in recent technical literature. These same principles can be modified and applied to complex precipitation-strengthened alloys such as the iron-, cobalt-, and nickel-base superalloys and the stainless steels. Since these complex alloys contain carbides and other phases that normally precipitate before the U-type phases, the nature and amount of the precipitated phases must be calculated first. The following general formula is then applied to the residual matrix composition of the alloy: element. The magnitude of the resulting number is indicative of whether the alloy will form a a -type phase. When these calculations (which are computerized) are systematically applied to alloys of knoun phase analysis, a breakoff in average electron-vacancy number is noted between U-free and U-prone alloys. Alloys with an average electron-vacancy number higher than the breakoff form a-type phases, while those with lower ones do not form these phases. This method could then be used to eliminate from consideration all experimental compositions that would precipitate undesirable phases. It also is useful in evaluating analyzed heats of alloys where minor heat-to-heat variations determine whether the alloy is o-free or o-prone. THE highly significant development of strong, ductile superalloys to provide reliable construction materials in the 1000" to 2500° F temperature range has been due principally to unremitting application of Edisonian techniques and logic by the dedicated physical metallurgists who have shouldered this responsibility. Tools such as the electron microscope, phase analysis, and computers to accomplish regression analyses have been used heavily, but the effort has been essentially practice of an art, rather than a science. The objective of this paper is to describe and illustrate application of some relatively fundamental principles to certain of these alloy systems in an attempt to remove some of the empiricism from the technology. Specifically, the work presented here deals with the use of periodic-group relationships to predict the formation of intermetallic phases which can occur in primarily austenitic (fcc) structures. Calculations that have been developed might be applied in the design of new alloys and the evaluation of known alloys, and thus have the potential of eliminating vast areas of unnecessary alloy preparation and evaluation. ALLOYING CONCEPTS AND STRUCTURAL FEATURES OF SUPERALLOYS Strength is produced in austenitic superalloys by three principle mechanisms: 1) precipitation of y&apos;; 2) formation of carbides; 3) solid-solution hardening by soluble refractory metals. The first mechanism requires the addition of aluminum and titanium, the second requires carbon and carbide-forming elements, while the third calls for the addition of molybdenum and/or tungsten. A considerable concentration of chromium is usually maintained to resist oxidation/corrosion, but it is also an important carbide-forming element. Fig. 1 shows a sketch and electron micrograph of the structure of a typical wrought nickel-base super-

Jan 1, 1967

By R. Lagneborg, R. Gullberg

An X-ray method for determinig volume fractions of phases in textured materials has been developed. The method involves measurements of the integrated intensities of reflections of each phase for one single orientation of the sample. The method was checked by evaluating the phase contents in samples from two stainless Cr-Ni steels containing austenite and ferrite in known amounts. In the present case measurements of about five reflections from each phase were required. The agreement between calculated and known volume fractions was found to be very close. AN X-ray diffraction method is often employed for determining the amounts of two or more phases in a material. The details of the method have been described at several instances.&apos;" In short, the method is based upon the fact that the integrated intensity of a reflection is directly proportional to the volume fraction of the phase considered. In principle, the method only requires the measurement of the intensity of one reflection for each phase. The most severe shortcoming with this method is that it disregards influences from preferred orientation in the material. In a diffractometer, where this type of analysis is most conveniently carried out, the geometry is such that the diffracting planes for a specific Bragg peak are all parallel to the surface of the specimen. This implies that it must be required that the occurrence of the diffracting planes parallel to the specimen surface must be as frequent as for any arbitrarily oriented physical plane of the sample. This requirement will generally only be fulfilled for a material free of texture. Since all materials in reality always exhibit a preferred orientation to some extent. the deficiency of the method is quite serious. In cold-deformed material the texture is appreciable, but also annealed material will in many cases display a considerable texture. The problem of quantitative phase analysis in textured material is one of obtaining the integrated intensity averaged over all orientations of the specimen with respect to the X-ray beam. Lopata and ~ula~ have shown that this can be accomplished by integration of intensities over the whole pole figure, or by random rotation of the specimen in the X-ray beam, or by a combination of both. Hence, in this method the average integrated intensity for a specific reflection is obtained by directly determining the intensity for a sufficient number of physical orientations of the sample. However, since an excess of diffracting planes in a certain surface plane necessarily must be accompanied by a deficiency of another type of diffracting plane, it appears to be possible to obtain the correct average intensity for a specific diffracting plane by performing an appropriate averaging of intensities belonging to a large number of diffraction planes of different hkl when all intensities have been produced from one single orientation of the specimen surface. In the present work such a method has been attempted and tested experimentally for two stainless Cr-Ni steels containing austenite and ferrite. 1) THEORY The expression for the integrated intensity of a Bragg reflection diffracted from a phase in a polycrys-talline sample in a diffractometer is: where C is a constant only dependent on the incident X-ray power and the diffractometer geometry, v the volume of the unit cell, F the structure factor, m multiplicity of the diffracting plane, L Lorentz factor, P polarization factor, e-2 temperature factor, p average linear absorption coefficient of the irradiated vO1umej and V volume fraction of the phase &apos;Onsidered. Hence, the factor R in the abbreviated form of Eq. [I] can be calculated and depends only on 0 and the diffracting plane {hkl}. For an alloy containing two phases, a and y, we can write

Jan 1, 1967

By C. N. Rosenecker

The power required to circulate a gas-solids suspension was determined using a centrifugal compressor and a closed system. The suspension consisted of 18- to 40-micron glass beads in a mixture of 89 percent N2 and 11 percent CO2 at 20 psig. Solids-to-gas (S/G) ratios w re O to 2.2 lb/lb; gas flow rates were l.2 to 2.5 lb/min. Power requirement was found to follow the relationship hp t = hp(. + l), where hp t = the total power, and hpg = the power required for pure gas.

Jan 1, 1967

By J. A. C. Fortescue

During the past decade, geochemical prospecting methods have become important in Canadian mineral exploration. The object of this paper is to discuss the role of geochemical methods in a typical mineral exploration program involving parallel geological and geophysical methods applied at different degrees of intensity. Particular attention is given to the description of the degree of development of geochemical prospecting under different kinds of local conditions.

Jan 1, 1967

By E. K. Kleespies

The rate of the heterogeneous reaction between titanium-oxygen solid solutions and titanium trichloride in molten sodium chloride was determined at high temperatures. In the alpha phase, the reaction rate decreases uniformly with the increasing concentration of oxygen. The gamma crystalline form of titanium (above 33 atomic percent oxygen) was much less reactive than the alpha phase, and the reaction rate approached zero at 50 atomic percent oxygen. The activation energy for the reaction of titanium-oxygen solution containing 22.8 percent oxygen was 11.7 kcal/mole of TiCl3 as compared with 8.3 kcal/mole of TiCl3 for pure titanium.

Jan 1, 1967

By C. B. Alcock, M. G. Hocking

The kinetics of the growth of sulfate layers on blocks of Cu20 has been studied between 688" and 800°C. At 788c the over-all weight increases followed the parabolic rate law, with k = 216 30 sq mg per cm4 min, using a 1:1 entering gas mixture of SO2:02. At 757 after an initial linear period the parabolic rate law was followed, with k = 57.8 10 sq mg per cm4 min. The gas mixture required a platinum catalyst to produce the maximum SOs pressure. The sulfation rate at 757&apos; and 788c was high until all the CUZO had changed into a core of CuO, when it became very much lower. At 757°C marker experiments showed that the sulfates (CuO. CuS04 and CuSO4) grow outwards from the oxide surface, but CuO. CuS04 mixed with CuO was found beneath the markers. At 688 markers were found at the CuO. CuS04/CuS04 interface. Visual observations at 757 showed a liquid eutectic moving beneath the sulfate surface. causing very rapid sulfation and extruding to solidify as thick &apos;needles" up to 8 mm long. Marker experiments have shown conclusi.cely that CuO grows on Cu20 in air by the outward migration of copper. ThermODYNAMIC measurements on the sulfate and basic sulfate of copper, reported recently,&apos; are followed here by measurements of the rates of formation of these sulfates on cuprous oxide, in order to provide a background for the understanding of roasting processes. peretti2 and McCabe and Morgan3 have shown that the phase Cu20 lies next to Cu2S when the sulfide is roasted under conditions where sulfates will be formed. Since this would present too complex a system for kinetic study, the present work4 has been based on the kinetics of sulfation of the oxide phase. The results of a study of the kinetics and mechanism of the sulfation of cobaltous oxide have recently been reported.4,5 Results on the sulfation of cuprous oxide have also appeared,6 but are at variance with those to be reported here. This seems to be because the previous workers6 did not obtain constant SO3 pressures from the SO2/O2 sulfating gas mixtures used, as will be discussed later. Wadsworth, Leiter, Porter, and Lewis found that the sulfates produced when SO2/O2 mixtures are passed over Cu20 at red heats are CuS04 and the basic sulfate CuO.CuSO4. When the decomposition of CuS04 was followed&apos; by differential thermal analysis, a stage corresponding to CuO .CuS04 was reached before decomposition into the oxide occurred. APPARATUS The vertical furnace used for quantitative studies was a conventional resistance-heated and propor- tionately controlled furnace with an even zone (1 deg) which was 4 cm long. The gas mixtures of SO2 and 02 were made by mixing measured flows from capillary flowmeters and drying over phosphorous pentoxide before passing them into the Pyrex top-piece of the furnace assembly. A mullite tube of bore 2% cm was used as reaction vessel and at the bottom of this tube was a trap for SO3, which condensed as a colorless liquid. The residual gas was led into a fume cupboard for ventilation to the atmosphere. The furnace used for visual observations of needle growth and other phenomena consisted of a transparent silica reaction tube of bore 3 cm, having an optically flat silica window sealed into its wall. The reaction tube was clamped vertically, inside a mullite tube of bore 4 cm and length 42 cm which was heated by Kanthal windings. The window in the silica reaction tube was arranged opposite a hole 3 cm wide and 2 cm tall which had been cut in the wall of the mullite winding tube 19 cm from its top end. A binocular microscope was used to look through the window, illumination being provided by a focusing microscope-lamp offset sideways and downwards. The oxide block to be sulfated was suspended from the removable Pyrex top-piece to the reaction tube, by means of which it was inserted at the start of the experiment, and through which entered the S02/02 gas mixture. The variation of the temperature inside the reaction tube with horizontal and vertical displacement from the window was investigated, and, while it can be said that the temperature was constant 1 deg, its value at a given position was known only to 12 deg. In both furnaces, the oxide block to be sulfated was suspended from a small silica hook immediately downstream from a platinum thimble used as catalyst, which was held on a long silica rod from a Pyrex spring attached to the removable Pyrex top-piece of the furnace. The spring was only included in the quantitative sulfating furnace; its sensitivity was 1.4 cm per g and it was found to be free from creep in a 16-hr test when carrying the working load. The extensions were followed by a cathetometer which could be read to 0.001 cm, corresponding to i0.7 mg. Extensions of the spring were measured on adding weights between 5 and 500 mg to the working load (thimble + oxide block), and Hooke&apos;s law was closely obeyed. SAMPLES Cuprous oxide blocks were prepared by oxidizing Johnson Matthey "Specpure" copper sheet of 1 mm thickness (impurities: iron at 3 ppm, silver at 2 ppm, lead, nickel, sodium, and silicon each at 1 ppm, calcium, chromium, magnesium, and manganese each at less than 1 ppm) for 6 days in air at 1000°C in a re-crystallized alumina boat. It has been reported7 that when Cu20 is prepared by heating copper sheet for 1 day the central plane of the blocks produced consists

Jan 1, 1967

By Lester G. Morrell

While developments in Australia dominated the minerals industry of the South Pacific area, New Caledonia&apos;s nickel, manganese ore from New Hebrides, gold from Fiji and New Guinea, and phosphate rock from several small islands were significant in world supplies of those materials. The total value of mineral commodities produced in this area in 1965 has been estimated at about $763 million an increase of nearly 16 percent over the value reported in 1964. Increases were recorded in mineral production value with respect to that of 1964 for all of the countries except Papua-New Guinea where lower gold output resulted in a drop of about $300,000 and in the several phosphate-producing islands that collectively recorded a value decline of around $1.3 million. Exploration and development activities continued at an intensified level, not only in Australia and New Zealand but also in the British Solomons, Bougainville, and Fiji. Substantial additions to world supplies of iron ore and bauxite are assured and recent discoveries of natural gas, manganese ore, and nickel combine to give Australia a brilliant mineral outlook. Important discoveries of copper on Bougainville Island and on Vanua Levu, the north island of the Fiji group, and a gold mine on Misma Island were being developed during the year, with plans for early production underway. In New Zealand progress has been made on the New Zealand Steel Company project, and preliminary appraisal of a new titano-magnetite beach sand resource on the South Island has aroused considerable industrial interest. Extensive geophysical investigations were carried out in the British Solomon Islands and on Fiji&apos;s goldfields. The expansion program that will double output of products by New Caledonia&apos;s Société Le Nickel continued through 1965, and several foreign private companies have expressed a desire to initiate additional industries based on nickel prospects in New Caledonia.

Jan 1, 1967

By P. Beardmore, B. W. Howlett, B. D. Lichter, M. B. Bever

The heats of formation at 273°K of the compounds Mg2Ge, Mg2sn, and Mg2b, the heats of fusion and melting points of Mg2Sn and Mg2Pb, and the heats of solution of magnesium, germanium, and lead in liquid tin have been measured. The excess free energies of the liquid alloys and the free energies of formation of magnesium-Group IVB compounds at their melting points and their standard free energies of formation at 298°K have been calculated. The stability and bonding of the compounds are discussed with reference to these properties. Some thermodynatnic aspects of the liquid phases in the systems Mg-Sn and Mg-Pb are also considered. THE compounds of magnesium with the Group TVB elements, silicon, germanium, tin, and lead, have often been considered to constitute a nearly ideal homologous series. In particular, their thermodynamic stability has been assumed to decrease with increasing atomic number of the Group IVB element.&apos; The binary-phase diagrams of the magnesium-Group IVB elements given by Hansen and Anderko2 have the same form. Each system has a single con-gruently melting compound of limited homogeneity range. The structures of these compounds, which have the formula Mg2X, are anti-isomorphous with the calcium fluoride structure. A recent investigation has found evidence of a second compound in the system Mg-Pb.3 The solid compounds Mg2Si, Mg2Ge, and Mg,Sn are semiconductors, while the conductivity of Mg2Pb approaches that of a metallic conductor. This difference suggests that other properties may also show a discontinuity. The investigation reported here is concerned with the thermodynamic properties of magnesium-IVB compounds and particularly their variations with the period of the Group IVB element. The heats of formation at 273°K of the compounds MgzGe, Mg2Sn, and Mg2Pb and the heats of fusion and melting points of Mg2Sn and Mg2Pb have been measured. The results, combined with published data, are interpreted in relation to the stability and the bonding characteristics of the compounds. Some thermodynamic aspects of the liquid phases in the systems Mg-Sn and Mg-Pb are also considered. In the course of the investigation the heats of solution of magnesium, germanium, and lead in liquid tin have been determined. 1) EXPERIMENTAL PROCEDURES 1.1) Samples. Samples of the compounds Mg2Ge, Mg2Sn, and Mg2Pb, supplied by Professor P. Aigrain, Compagnie Générale de Télégraphie Sans Fils, were used in measuring heats of formation, heats of fusion, and melting points. Samples of Mg2Sn and Mg2Pb, supplied by Dr. V. B. Kurfman, Dow Metal Products Co., samples of Mg2Sn, prepared at the Air Force Cambridge Research Laboratories, and samples of MgzPb, prepared in this laboratory, were used for additional measurements of the heats of fusion and the melting points. The samples were stored in evacuated Pyrex capsules or under nonreacting liquids. 1.2) Heats of Formation. The heats of formation at 273°Kof the compounds Mg2Ge, Mg2Sn, and Mg,Pb were measured by tin-solution calorimetry. In this method, samples of the compound and of a mixture of the constituent elements are added alternately from 0°C to a tin-rich bath. The difference between the heat effects, corrected for the change in composition of the bath, is the heat of formation of the compound. Details of the method have been given elsewhere. 4 The bath was maintained at 350°C for the dissolution of the compounds MgzSn and Mg2Pb. Since at this temperature the dissolution of Mg2Ge was too slow, a bath temperature of 400" or 450°C was used with this compound. At least three calorimetric runs, each of approximately six additions, were made with each compound. 1.3) Heats of Solution. The determination of the heats of solution of magnesium, germanium, and lead in tin was included in this investigation because they were not well-established at the time this work was started. To obtain the heat of solution, the difference

Jan 1, 1967