Search Documents

Study on Desulfurisation and Deashing for Medium-High Sulfur Coal Using Shaking Table As important coal resources, medium- high sulfur accounts for a significant part of the coal reserve in China. The environmental regulations and fuel standard requires sulfur and ash to be removed before it is used, so as to save energy and decrease the emission. Therefore, the effective desulfurisation and deashing technologies are urgent needed. However, due to the local characteristics of the coal, specific technology with optimum operation parameters is required to develop for different local coal. Qinglong is a district of Guizhou Province, which has large medium to high sulfur contained coal reserve. In this paper, medium-high sulfur coal is sampled from Qinglong, Guizhou province. Some basic characteristics such as the mineralogical composition of the coal rock, the monomer existing state and the granulometric composition are determined by X-ray diffraction quantitative analysis and polarisation microscope analysis respectively. Adopting the classified feed method, shaking table tests show that the feed pulp concentration is 20 per cent, the stroke is 13mm, the frequency of the stroke is 380 per min, the cross slope is 3¦ and the volume of wash water is 5.2 L per min. Under such condition, aggregate processed coal yield is 72.87 per cent and sulfur content decrease to 1.31 per cent With shaking table technology of 'First stage rough and intermediate further fine benefication', the yield of concentrate coal increased from 72.87 per cent to 81.21 per cent, while the sulfur content reduced to 1.35 per cent.

Sep 13, 2010

The Rate Variable Batch Test (RVBT) - A Research Method of Characterising Ore Floatability

Sep 13, 2010

Similarities and Dissimilarities in Florida Phosphate Ore Types - Surface and Bulk Property Analysis of the Flotation Feed, Concentrate and Tails

Sep 13, 2010

Effective Dry Density Benefication of Coal

Sep 13, 2010

Rutile Beach Sand from Hard Rock

Sep 13, 2010

Characterisation of Manganese Ores

Sep 13, 2010

Eco-Efficient Gravity Separation Solutions in India Sustainable development and social responsibility issues are a principal aspect of mineral processing operations around the world. With the need for more environmentally effective technologies, some gravity separation systems have provided eco-efficient mineral processing solutions in places where it is not otherwise viable because of lack of fresh water or for other environmental reasons. Advanced spiral separation technologies developed in Australia offer a cost effective and environmentally viable way to process minerals. In particular, we review recent case studies of spiral plants commissioned in India where environmentally sustainable solutions to design problems included the use of spirals operated with sea water and the use of high capacity (HC) spirals to provide low consumption of energy and materials and a reduced plant footprint. This paper evaluates the performance of various spiral plants in India and how critical environmental issues which affect the overall viability of wet concentrating processes where resolved.

Sep 13, 2010

Valuable Components Recovery from Lead-Zinc Metallurgical Slag

Sep 13, 2010

Techniques Used and Problems Encountered in Normal and Reverse Circulation Drilling at the Mt Roseby Project, Cloncurry, North West Queensland

Sep 13, 2010

Microfluidic Solvent Extraction for Mineral Processing of Copper Leach Solutions

Sep 13, 2010

Improvement of Phosphate Ore Flotation Performance Through Sized Flotation

Sep 13, 2010

A Study on Main and Interaction Effects of Operating Variables of Column Flotation

Sep 13, 2010

Comparison of Discretised Population Balance (DPB) and Finite Element Method (FEM) Methodologies for Modelling Batch Gibbsite Precipitation

Sep 13, 2010

Recovery of Fine Gold Particles from Philippine Gold Deposits by Enhanced Gravity Concentration and Flotation The objective of the study is to determine the applicability of enhanced gravity concentration (EGC) and flotation for gold recovery. While gravity concentration methods have long been applied to gold ores, especially to free-milling types that requires minimal beneficiation, flotation for gold recovery has not yet taken hold as a major operation in the Philippine setting. In this study, the application of EGC and flotation for gold is applied and compared to the existing methods for gold recovery. Two samples, with assays of 7.315 and 5.333 g Au/MT (samples 1 and 2, respectively) are used for this study. These samples are subjected to mineralogical studies and is found to have a gold-particle size ranging 10 to 200 microns. To verify the separation size, the mesh-of-grind (MOG) is used as the primary parameter for experimentation. Initially, the samples are stage-crushed, ground, and subjected to EGC using a Falcon SB40 Concentrator. Based on the results, the two samples showed that recovery increases with a finer MOG. The ratio of concentration (K) decreases with a finer MOG. This shows that there should be sufficient liberation of the gold values for EGC to be effective. The effect of the enhancement is to pronounce the difference in specific gravity of the minerals, promoting better separation. This is validated by the high recovery values of 86.97 per cent and 98.73 per cent exhibited respectively for samples 1 and 2 (at 54 microns). For the flotation runs, sample 2 with an average particle size of 80 per cent passing 74 microns is examined using thiocarbamate-based collectors for roughing and subsequently exhibited a recovery of 96.32 per cent. At this point, the concentration ratio (K) is noted as an important efficiency indicator for flotation process since it yielded a very low-mass and high-metal content concentrate.

Sep 13, 2010

Study on Beneficiation Technology of a Refractory Fluorite Ore in North China

Sep 13, 2010

Adsorption Effect on Multi-Heavy Metal Ions in Wastewater by Water-Washing Waste Saccharomyces cerevisiae

Sep 13, 2010

Methods for Improving the Flotation Recovery of the Coarse Fraction of a Nickel Ore

Sep 13, 2010

Simulation and Analysis of Media Behaviour in the Tower Mill by Discrete Element Method for Estimating the Power Draw and Spatial Distribution of Grinding Process The trends to the Tower Mill (TM) for grinding the materials are increased recently due to its unique merits. Among the various considerations of this machine, the main important items are increasing the efficiency of grinding as more as possible while keep the power consumption, manufacturing and maintenance costs as less as possible. Because this grinding process includes a huge numbers of media particles (ball or other shapes) that are interacted with each other and body of the machine, the DEM (Discrete Element Method) way is a very useful and essential step to getting confident evaluations. Because the DEM simulation is a very young scientific field and proper commercial software are very rare and still under modification, at first step, a FORTRAN code is developed for DEM simulation of two laboratory Tower Mill models (KM5 and KD5). The simulation and experimental results matched each other properly. Then one another DEM software was implemented to perform simulation of bigger models (huge numbers of balls), meanwhile could handle the complex 3D geometry data. The simulation and experimental results were compared and analysed in detail for not only laboratory but also for industrial models (KW5, KWD5, KWD50, KW300F, KW700F and KW1500) without any manipulation or compromising of the parameters of simulation. Some numeric data of industrial models are hidden here due to confidential reasons. The relative velocity of balls (ball-ball and ball-TM body), dissipate energy, interacted forces and stresses during the process are the key outputs of DEM simulation for design this machine. Therefore the main important processes in a Tower Mill machine are recognised and consequently some horizons of development of this machine are distinguished.

Sep 13, 2010

The Operation of the LAROX PF-50 Pressure Filter at 'Ellatzite-Med' Flotation Plant, Bulgaria The implementation of Larox pressure belt filter, type Larox PF-50 provided within 6˜8% moisture content of the produced copper concentrate, which allowed good market realisation. The start-up of the pressure filter in 2009 reduced the electricity costs several times and had a positive impact on the technological regime of flotation. This article reveals the investigation results from the operation of the pressure filter according to different situations (density of the pulp, time for filtration, pressure of the material, pressure of the drying air, time for drying with air and other factors). The investment made in the pressure filter application is a guarantee for the successful operation of 'Ellatzite' flotation plant, Bulgaria in the coming years.

Sep 13, 2010

An Integrated Geology-Mine-Plant and Eco-Efficiency Simulator for Anglo Platinum's Evaluation and Operational Improvement Initiatives

Sep 13, 2010