Search Documents

Since the beginning of the computing age, technical software packages have not been developed to address only programming specialists but have been dedicated to process engineers. For process analysis, BRGM is developing and commercializing three packages: ? sampling software: ECHANT 2.0 for Windows ? material balance calculation: BILCO 2.0 for Windows ? steady-state simulator for plant design, adaptation and optimization: USIM PAC 2.1 for Windows This paper deals in a first part with the main features of these three packages. In a second part, advanced models are presented for SAG/ AG mills and flotation columns. An industrial case of application is shown for each of them.

Jan 1, 1997

By Michael Noy

Current image based systems used to measure fragmentation are measuring the two dimensional presentation of a set of three dimensional objects. A two dimensional measurement of fragmentation restricts both sampling and particle size classification and hence provides a different evaluation of the fragmentation to that of a conventional sieve analysis of the same sampled material. Many modern image based fragmentation measurement systems attempt to convert this two dimensional analysis to a three dimensional analysis in order to deliver a "real" measurement of the fragmentation distribution. This paper questions the necessity and validity of this transformation and lays down the framework for the establishment of a standard in fragmentation measurement based on a two dimensional analysis. The results of image based measurements of laboratory prepared samples indicate that differences in mass distributions (3D distribution) can be mapped by an appropriate image based analysis which provides area versus particle size information.

Jan 1, 1997

By D. F. Scott

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, detect hazardous ground conditions, and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep (> 1220 m) underground pillars. If high-stress areas are detected, they can be destressed prior to development or avoided. High-stress areas can be monitored with successive seismic surveys to determine if stress decreases to a level where development can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost-effective, efficient, and non-invasive. Also, investigators can monitor large rock masses, as well as monitor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer environment.

Jan 1, 1997

By Howard G. Coopersmith

Kelsey Lake kimberlites are a cluster of eight diamondiferous pipes that occur in the northern State Line kimber lite district of the Colorado-Wyo¬ming diamond province (Coopersmith 1991, 1993) (Fig. 1). This is located at the southern margin of the Wyoming Archean province. Two relatively large pipes and a few smaller bodies define the cluster (Fig. 2). The Kelsey Lake kimberlite cluster has been developed as the first diamond mine in the United States. The cluster was discovered in 1987. Full-scale production began in the spring of 1996. Mining has produced gem-quality diamonds up to 28.3 carats in size. The 30 State Line kimberlites, intruded about 390 million years ago into Proterozoic crystalline rocks, were presumed to be underlain by Archean basement of the Wyoming Province. Nearly all the kimberlite pipes contain diamond but only the Kelsey Lake pipes are economic. The Kelsey Lake kimberlites contain predominately diatreme facies kimberlite, with minor hypabyssal and crater facies rocks locally occurring. Alteration and weathering of the kimberlites is extensive. Petrologic studies indicated an underlying lithosphere that has a largely Proterozoic signature and shows evidence of deep melt and metasomatic events. Current development has concentrated on the two largest pipes. These have been bulk-sampled after geological study (1987) identified the presence of small diamonds and mineral chemistry indicating favorable diamond conditions. A 10-t/hr (11-stph) rotary pan plant was established in 1992 to process thousands of tons of bulk-sample material. Grades and gem-quality diamonds to 14.2 carats in size were recovered. Early in 1995, it was decided to move from evaluation to commercial mining. Production began in early 1996. A 195-t/hr (215-stph) rotary pan plant was built. A water supply system and tailings disposal have also been incorporated. The project straddles the Colorado/Wyoming border. Existing mining permits were amended to incorporate the increased scale and new plant facility. The permits for this project included the following: Colorado mining permit, Wyoming dozing permit, Corps of Engineers Section 404, Colorado NPDES, Wyoming NPDES, Storm water Management Plan, Air Pollution Emission Notice, various Colorado and Wyoming State Engineer and well permits, Substitute Water Sup¬ply Plan, Larimer County Special Use Review, and US Forest Service road use permits. The temporary destruction of a wetlands area was a sensitive issue. It has been addressed through the Clean Water Act Section 404 permit administered by the US Corps of Engineers. This use will be mitigated by creating new, self-sustaining wetlands in the immediate drainage system. A comprehensive and bonded reclamation plan is incorporated in the permits. Diamond mining and ore processing is environmentally benign. No chemicals are used in processing the diamonds. The plant is a water wash facility. The kimberlite ore is inert, as is the granite wall rock. The exposure of the ore body and the subsequent ore processing and waste rock and tailings containments pose no threat of release, leaching or dispersion of any detrimental elements. There is no acid-forming waste. Even a prolonged acid rain environment will not produce a harmful leachate. Slimes containment and clarification ponds will prevent unacceptable levels of suspended solids in water discharge. The isolated, restricted access and nonvisible nature of the mine and processing has led to straightforward permitting. Geology The State Line district is located in the northern

Jan 1, 1997

By D. Hong

The leaching behavior of rhenium in ammonium iodide solutions with iodine as oxidant has been studied. Experiments were carried out in an autoclave. The effect of stirring speed, temperature, pH of the solution, iodine and iodide concentrations on the dissolution of rhenium was investigated. It was found that high temperature and high pH of the solutions were essential for the efficient leaching of rhenium. The dissolution rate was found to be dependent upon the concentration of iodine and iodide. It was concluded that the dissolution of rhenium under the conditions studied was controlled by mass transfer of iodine with an apparent activation energy of 15.77 kJ/mole.

Jan 1, 1997

By Salah A. Taqieddin

Blast casting or trajectory blasting, as it is sometimes called, is an innovative mining technique that has been receiving increasing acceptance among operations of surface coal mines and quarries as a means of offsetting the rising cost of mechanical excavation of overburden with a high overburden-to-ore ratio. Many similarities exist between geological characteristics of overburden formations of phosphate beds and the formations that conceal coal seams. Both are sedimentary origin and are removed for mining in an identical manner (i.e. use of a dragline or shovel to strip or cast the overburden aside).

Jan 1, 1997

By C. A. Silva

The kinetics of chlorination of titanium-bearing raw materials has been investigated. For comparison purposes pellets of controlled macro-porosity, made of analytical grade TiO2 and anatase concentrate (Brazil) , have been exposed to different combinations of gas composition - CO, CO2, C12 -, gas flowrate and temperature. A thermogravimetric technique and an adapted grain model have been used in order to assess the influence of the several experimental parameters upon the chlorination behavior.

Jan 1, 1997

By Mudge S. T

Tin mineralisation occurs at Renison Bell, near Zeehan in Tasmania, as a group of cassiterite-bearing massive pyrrhotite bodies in Cambrian sedimentary rocks. Mineralising fluids from the underlying Pine Hill Granite have replaced carbonate rocks with massive sulphides and cassiterite. The discrete blocks of massive pyrrhotite have high density and high magnetic susceptibility contrasts with the comparatively barren country rock. They are strongly remanently magnetised and are excellent geophysical targets. A detailed geophysical model of the mine was created from a database comprising 1:2500 scale geological mapping and geological logs of approximately 4000 drill-cores. The model comprises 93 parallel cross-sections, each 1.5 km long, spaced 20 m apart. Each cross-section is comprised of up to 150 polygons which represent all known individual rock types and orebodies. The magnetic response of the model was computed and the residual between the model and the observed response, measured by a low-level helicopter magnetic survey, revealed several anomalies unaccounted for by the model. Drill testing of these anomalies led to the discovery of several hitherto unknown massive sulphide occurrences. Surface gravity data of the mine and surrounding district were enhanced by applying digital terrain corrections. The corrected Bouguer anomaly revealed a hitherto unknown positive anomaly associated with the ore zones of the Renison mine. The gravity anomaly of the model was also computed. Unfortunately, the limited resolution of the observed data prevented the delineation of ore targets. The terrain-corrected Bouguer gravity data were also used to model the shape of the underlying non-magnetic Pine Hill Granite. A computer inversion method was implemented to build a 3D block model of the granite. Results agreed with previous conventional 3D modelling techniques but yielded improved resolution of the granite form. The project involved development of new computer software to build and edit the large and complex 3D geophysical model of the mine and to compute the model's magnetic and gravity responses. Software was also developed to build and compute the gravity response of a 3D block model of the underlying granite.

Jan 1, 1997

By Sigmund J. Sulinski

All Sanitary District contract documents for new tunnel construction permit the Contractor a choice of four (4) separate alternate tunnel sections. This is the result of a continuing District policy to encourage at all times the use of the most suitable construction techniques and to attract to District construction the broadest spectrum of proven capabilities. Figure 1 indicates the alternate tunnel sections allowed on District contracts as follows: 1. A horse shoe section, ribbed and lagged, and a poured reinforced concrete tunnel liner; 2. Circular section, ribbed and lagged, and a poured in place reinforced concrete tunnel liner; 3. Circular section, ribbed and lagged, and a precast reinforced concrete pipe liner grouted in place; and 4. Circular section, no temporary lining, and a precast reinforced concrete pipe liner to be jacked in place. The Sanitary District now has in operation 10,500' of 5'6" I.D. and 6,500' of 5'0" I.D. jacked tunnel. An additional 5,600' of 7'6" I.D. jacked tunnel is currently under construction.

Jan 1, 1997

By C. A. Wiggins

The new Niagara Falls Intake Tunnel, mined in the highly fractured Lockport Dolomite, encountered prolific inflows of water contained in rock seams directly linked to the Niagara River. These inflows were pressurized and, more significantly, contained high concentrations of dissolved H2S gas. The contractors attempts to control the water/gas inflows included cement and chemical grouting from inside the tunnel. Ultimately, improving the rate of air exchange in the tunnel by increasing the fan capacity, in conjunction with a pattern down-hole pre-grouting program along the tunnel alignment allowed the contractor to control the concentration of H2S gas and complete the tunnel.

Jan 1, 1997

By Y. M. Jubeli

"Gamma-ray spectrometry, an effective tool in geological mapping, was used to de?ne boundaries between various lithological formations in three adjacent areas of Central Syria, namely, the Syrian Desert, Ar Rassafeh Badiayat and the Northern Palmyrides mountains.This paper describes the role of an airborne gamma spectrometric survey which was originally undertaken to assist uranium exploration. Interpretation of the total count data obtained through the survey has led to signi?cant modi?cations and corrections to the previously published distribution map of the palaeogene phosphate rocks.Another important result of the survey is the discovery of four previously unknown phosphorite horizons in the Rasm Al-Aawabed area of the Northern Palmyrides. In addition, previously unknown phosphatic horizons are outlined in the other study areas. The importance of this technique as an effective prospecting method, not only for U but also for exploring for the economically important phosphorite formations in Syria, is emphasized. Furthermore, its role in geological mapping is stressed, especially in areas that lack suf?cient geological data."

Jan 1, 1997

By M. J. Laurila

On-line analyzers have made possible the use of Fuzzy Logic Control (FLC) for local control applications in coal preparation plants. This includes FLC control of complete circuits such as heavy media vessels, cyclones and froth flotation. These circuits can be controlled in real time in a feedback control loop with an on-line analyzer. Control strategies can be readily developed using Statistical Process Control (SPC) techniques which are first applied off-line in manual mode through the use of control charts and then this process is brought on-line using FLC in conjunction with an on-line analyzer to fully automate the circuit. This paper outlines the types of control strategies employed and presents examples of automatic verses manual control.

Jan 1, 1997

By Andreas Nolte

This paper includes a comprehensive report about the metallurgical utilisation of reusable products from electronic scrap recycling, car shredding industry, used glasses an various waste products, such as slimes and flue dusts, generated in a secondary copper smelter. Depending on the copper content, the type of copper compounds and the characteristics of accompanying substances, the materials are treated by smelting in furnaces, operating under reducing or oxidizing conditions. HKs pyro- and hydrometallurgical processes, blast furnaces, converters anode furnaces, tin lead alloy plant and tankhouse will be outlined. The reusable products are categorized according to the origin of the materials and then presented in the form of quantity and quality balances. Processing methods, process able quantities and quality requirements of inputs are described. The utilization degree of the most important metals (copper, tin, lead and zinc) is described with graphics. The report is rounded by information on operating licence according to the environmental regulations of the Federal Republic of Germany and data concerning supply and contracts

Jan 1, 1997

By Rafael C. Castro, John Overton, Gregg Sherry, David A. Sutter

This paper presents an innovative ground support solution developed to construct a tunnel cross-passage for the MUNI Metro Turnback (MMT) Project. A “soft center” jet grouting approach was designed to provide solid ground support while maintaining a soft center to allow for hand-mining of a 2.44 m (8 ft.) wide, 3.66 m (12 ft.) tall and 4.6 m (15 ft.) long cross-passage through soft Bay Mud. Prohibitive costs and schedule impacts associated with mining under compressed air (at the time being used for main tunnel construction) were the catalysts to search for alternative methods for cross-passage construction. Limited surface disruption, relatively low costs, ease of subsequent excavation, nominal schedule impacts and proven local success of jet grouting were key factors in selecting and designing this method of ground support.

Jan 1, 1997

By Pedro Marques Bernardo, Carlos Dinis da Gama

This paper presents a methodology for design and simulation of underground ventilation networks, based on the analysis of real situations, followed by the careful interpretation of the obtained results in order to implement their optimization. The method involves two basic steps: the construction of a complete ventilation data base for the mine, upon a series of care- fully previous surveying studies in order to determine the values of its ventilation parameters, and the simulation of relevant situations for the ventilation system optimisation. A simulation model, modified after the Hardy Cross method, allows the testing of various mechanical means located at different points of the network, aiming to determine the technical-economical feasibility of each solution. These simulations obey the directions of air flow in each point of the mine, as determined by the directions of the natural ventilation flow established in the data base that represents the network. The methodology was validated upon studies developed in ventilation network of the Panasqueira Mine (Portugal), in two situations: regular production (mechanical ventilation) and care- maintenance (natural ventilation).

Jan 1, 1997

By Pertti Paavola, Hikki Rasanen

This paper describes a very exacting tunneling project. Planning and technical realization of this service and transportation tunnel was especially difficult as a matter of vibration control, because the tunnel is situated only a few meters under Maria Hospital, which is one of the most busiest hospitals in Helsinki. In this hospital there are many departments for bedpatients, research and treatment with high-tech equipment, operational surgery and a big laboratory. Besides access tunnels are situated near several apartment buildings. The functionality of the tunnel required the placement of the access tunnels to be straight towards these apartment buildings for which special care for blast induced air pressure had to be taken.

Jan 1, 1997

By Z. M. Zhang, Y. Luo, S. S. Peng

This paper presents the precise definitions of a number of commonly used subsidence parameters. Using an integrated approach, the parameters were determined for 110 subsidence cases collected from major US coal fields. Attempts were made to establish empirical formulae for the parameters. The results of this study indicate that some traditionally held concepts should be changed.

Jan 1, 1997

The REL of 1 mg/m3 for respirable coal mine dust does not assure a zero risk for the development of occupational respiratory diseases among all miners exposed during a full working lifetime. Consequently, a medical screening and surveillance program that includes initial and periodic chest X-rays and spirometric examinations is important for the early detection of disease and the prevention of "material impairment of health or functional capacity" [30 USC 8 11(a)(6)(A)]. The medical screening and surveillance program is also useful for disease surveillance, which includes the tracking trends, the setting of prevention and intervention priorities, and the assessment of prevention and intervention efforts. NIOSH encourages both underground and surface coal miners to participate in the medical screening and surveillance program.

Jan 1, 1997

By Karl A. Gschneidner

Magnetic refrigeration was first used in the mid-1920's and new developments seem to have taken place about every 20 years, and this is especially true for the mid-1990's. The active magnetic regenerator magnetic refrigerator has the promise to become the first practical machine utilizing the magnetocaloric effect for cooling (and also heating). The basic principles are briefly discussed. Since the temperature lift for the magnetocaloric effect spans about 50 K, one will need to utilize several ferromagnets with different magnetic ordering temperatures in order to reach temperatures below ~250 K. The basic properties, behaviors, limitations, and new phenomena and knowledge are discussed.

Jan 1, 1997

By Chien-Tsun “C. T. ” Chu, Drupad B. Desai, Ron E. Redd

The 12,710-m (41,720-ft) Riverside Badlands Tunnel is located between the most active faults—San Andreas and San Jacinto—in Southern California. To accomplish the impervious final lining design and to accommodate the effects of earthquake ground motions, a new approach was developed and is prescribed in this paper. Two final lining options, welded steel pipe and prestressed concrete cylinder pipe, are considered for the tunnel, which will be excavated under groundwater and ground conditions from soft rock to hardrock at depths exceeding 244 m (800 ft). The buckling strength, serviceability, and structural integrity under seismic effects and other loads were considered in the design.

Jan 1, 1997