Search Documents

By A. V. Shroff

The Indian Standards code of practice for design and construction of underreamed piles contains provision for installing such piles in expasive soils. In recent years, a large amount of research work has been carried out in the analysis, design, construction and performance of underreamed piles in expansive soils. This paper suggests that the results of this research field tests should be included in the code. Various additions and modifications as well as deletions that should be incorporated in the code are discussed.

Jan 1, 1996

By N. P. Kripakov

Results of a complex three-seam interaction analysis in a western U.S. coal mine are presented. The physical situation simulated by the models represents the development of a set of entries underneath two previously mined seams with all three seams in proximity to each other. The layout and the geometry of the remnant pillars in the upper seams were nonuniform and not always directly superimposed over each other, creating a very challenging modeling problem. The U.S. Bureau of Mines' MULSIM/PC computer code was upgraded and enhanced to perform the required three-seam interaction calculations. Analysis was limited to simple linear-elastic assumptions as only peak stresses were required. Results clearly indicated that stress concentrations in the lower seam increased approximately 100 percent when compared to cases simulating no extraction in the two upper seams. These stress concentrations generally occurred in zones directly below points of highest abutment pressures in the upper seams. Overall, the model results compared favorably with actual documented observed behavior where roof failures were known to have occurred.

Jan 1, 1996

By Eric J. Foell

Recognizing that the planned commercial exploitation of polymetallic nodules in the deep sea should be accompanied by environmental studies in order to protect this largest and least understood ecosystem of our planet, the German Ministry for Research and Technology has since 1989 funded a longterm and large-scale disturbance-recolonization (DISCOL) experiment in the abyssal Peru Basin of the equatorial South Pacific Ocean. The circular study site is located at 4150m depths and encompasses about 10km2 of relatively flat, heavily sedimented sea floor with low (< 15%) nodule coverage near an existing German nodule mining exploration license area. The RV SONNE, a large and well-equipped multi-purpose research vessel, served as platform for all environmental cruises conducted to date. The initial DISCOL expedition (SO-61, Feb.-March 1989) was carried out in two legs. During DISCOL 1/1, a study site was selected, a pre-disturbance baseline assessment was undertaken, and sea floor disruption was begun using the "plow-harrow", a uniquely designed disturber device towed repeatedly across the circular study area. During DISCOL 1/2, disturber deployments continued until the device had created 78 criss-crossing and partially overlapping tracks along which nodules were essentially plowed under while sediment from up to 15cm below the seabed had been turned over and exposed at the surface. In addition to the obvious within disturber track impacts, sediment mobilized by plowing drifted off with the prevailing near-bottom current and redeposited downstream, blanketing nearby areas not directly disturbed. Immediately after the disturbance phase, an initial post-impact sampling series was performed. The DISCOL Experimental Area (DEA) was revisited about six months (DISCOL 2, SO-64, Sept. 1989), three years (DISCOL 3, SO-77, Feb. 1992), and seven years (ATESEPP SO-106, Jan.-March 1996) after disturbance to collect further post-impact samples, monitor changes in the benthic community and follow the recolonization process. In addition to benthic community studies, plankton investigations were initiated during the third DISCOL cruise (SO-77) and continued during three further cruises (SO-78, SO-79 and SO-80/2) in 1992.

Jan 1, 1996

Mineral Resource Technologies(MRT) and Michigan Technological University (MTU)finalized an agreement that permits MRT to offer an advanced carbon removal technology process for coal fly ash from an ash residue generated by utilities. The agreement encompasses the dominant existing US patents using a wet process for fly ash enhancement. The wet process for coal beneficiation of a fly ash product involves four steps. First, a slurry mixture is formed of a fly ash material and a liquid. Second, gravity is used to separate and collect a first-material fraction of the fly ash, having a density less than the liquid. This is done by skimming off the flotation slurry material.

Jan 1, 1996

By Mehmet F. Taner

"The East Sullivan Stock (ESS) is a small, composite felsic alkaline pluton of presumedlate Archean age in the Val d’Or mining district. Three main facies have been distinguished: mon-zonite sensu stricto, porphyritic monzonite, and green trachytic porphyry. This monzonitic group ofrocks is of relatively homogeneous composition with high abundances of Na2O, K2O, Ba, Sr, Rb, Zr,Mo and LREE. The alkaline ESS is distinguished from other igneous units in the Val d’Or miningdistrict, such as the Bourlamaque Batholith, by relatively high concentrations of Ba, Sr, Rb, Mo, Cuand Au. The ESS hosts many base (Cu, Mo) and precious (Au) metal occurrences, including: (1)porphyry style Cu-Au-Mo disseminated sulfde deposits, (2) Cu-Au deposits in volcanic rocks near the ESS contact, and (3) pyritic gold mineralization in east-west trending shear zones. The ESS is well defined by concentrical zoning on the aeromagnetic vertical gradient color map, and displays four linear trends, which are assumed to be structural lineaments, at 035°-055°, 320°-300°, east-west, and north-south. The main mineral occurrences related to the stock display a preferred spatial association with the east-west linear magnetic trends.The ESS is preferentially located along a major structure and was emplaced late in the evolutionof the Abitibi subprovince like other felsic alkaline plutons. This stock is similar to late-tectonic min-eralized felsic alkaline intrusions of the Kirkland Lake and Larder Lake mining districts in Ontario, and to the Allard stock in the U.S.A. which is associated with gold and base metal mineralization. Similarities also exist with younger alkaline plutons associated with Cu-Mo-Au porphyry deposits in the Canadian Cordillera, which formed in tensional tectonic environments. The felsic alkaline magmamay have formed by partial melting of deeply buried supracrustal rocks, concomitant with the development of deep fractures such as the Cadillac Fault. In such an environment, hydrothermal solutions carrying remobilized metals from deep supracrustal rocks may have deposited gold and base metals in structural traps. Plutons similar to the ESS should be good targets for mineral exploration. Copyright © 1996 Canadian Institute of Mining, Metallurgy and Petroleum."

Jan 1, 1996

By Graham J. C. Carpenter, Marc Charest, Jason Lo

"The method of producing magnesium-based composites with silicon carbide (SiC) particulates embedded in the matrix of magnesium AZ9I D alloy by the squeeze-casting technique are described. This method involves the fabrication of a SiC particulate preform and the subsequent squeezing of molten magnesium into the preform. In this study, alumina, aluminum phosphate and a proprietary binder were used for the fabrication of SiC particulate preforms. The procedures employed in the fabrication of SiC! AZ9ID composites are presented, together with the results of characterization of the composites using optical and transmission electron microscopy. Special attention is given to the reaction products in the bulk alloy and at the interfaces between SiC particles and the AZ9ID matrix alloy.1. IntroductionInterfacial, microstructural and metallurgical characteristics play an important role in determining the mechanical properties of a composite. In theory, reinforcing magnesium with SiC particulates should provide an improvement in strength and modulus of the composite over the unreinforced counterpart. However, many factors resulting from the fabrication process can cause degradation rather than improvements to the mechanical properties. In particular, the interfacial characteristics are known to critically influence the properties of composites [1]. Before evaluating the mechanical properties of a composite, it is always useful to examine the microstructure, which is closely related to the mechanical behavior. This helps to reduce the labor-intensive steps of sample preparation for mechanical property evaluation, which can be particularly difficult as a result of the high hardness of composite materials, as well as providing a wealth of information on the microstructural and interfacial characteristics, particularly the reaction products caused by processing. This information is also pertinent in understanding the factors governing the mechanical properties of the composites.There are many factors which determine the nature of the interfacial characteristics of a SiClMg composites. Qualitative estimations of the interfacial bonding have been performed based on thermodynamics, electronic and electrostatic concepts. In addition, the kinetic conditions during the fabrication play an important role. From an interfacial energy standpoint, the driving force for the formation of a metal/ceramic interface is the decrease in free energy that occurs when intimate contact is established between metal and ceramic surfaces. The simple representation of the energy change per unit area of interface formed (~G) is given by Dupre equation [2]:"

Jan 1, 1996

By Douglas A. Anderson

Mine the Internet? You bet. Precious information resources are there to be found by those willing to explore. Of course, the stratigraphy and the exploration tools must be learned. This article is is designed to help learn those tools and how to find the information that can help the reader. However, beware the Internet. It can be addicting. On the other hand, information can be found that you never suspected. And users can make contact with people who might otherwise never have crossed their paths.

Jan 1, 1996

By Patrick R. Taylor

Ilmenite concentrate and methane are fed to a non-transferred arc thermal plasma reactor to produce a powder that is primarily TiC and Fe. This material has promising characteristics for powder metallurgy applications. Free energy minimization plots were used to predict the feasibility of the reaction. An estimate of the optimum molar ratio between the ilmenite concentrate and methane was made based on the mineral composition. Argon-helium mixtures were used as plasma gases. The effects of power input level, carrier gas flow rate, powder feeding rate, and methane-ilmenite molar ratio were studied and the behavior of the system characterized. Two different powder injection angles were tried. A mathematical model to describe the temperature profiles in the reactor was formulated and solved. The product has been characterized by x-ray diffraction and atomic absorption. A conversion of 97 % of Ti to TiC was achieved. It was found that minor amounts of titanium oxides, iron carbide and free carbon are also present. TEM and SEM were used to study the morphology.

Jan 1, 1996

By S. Street

The Environment process, invented by Prof. H.K.Womer and developed at the University of Wollongong, simultaneously treats ferruginous and organic wastes via bath smelting. Conceived in the late 1980&apos;s, the patented process was originally developed using steelworks dust to settle solids from sewage, producing a composite material suitable for smelt reduction. Work began on the process in 1990 with the Australian patent having a priority date of February 1990. Early research focussed on settling of solids from sewage, while pyrometallurgical investigations examined smelting in small induction furnaces. By 1992 smelting trials had been undertaken in pneumatic and electric arc furnaces, the process being successfully demonstrated up to on 8 tonne scale. The success of this particular trial, and other smaller trials, resulted in construction of a 100kg DC arc furnace which was commissioned in 1993. By 1994 the main project focus was on development of the smelting technology. Over 3 years of trials on the DC arc furnace have identified and clarified many of the pyrometallurgical reactions. optimum operating parameters, as well as demonstrating the versatility of the process for treating a wide range of wastes. Currently the Illawarra Technology Corporation (lTC), the commercial arm of the University of Wollongong, is pursuing commercialisation of the process.

Jan 1, 1996

By V. T. Ganpule

The effect of Sulphate and Chloride is well understood by the engineers. Most of the codes stipulate permissible limits for sulphate and chloride content in groundwater. Relatively few reference are available about the effect of organic acids on pile concrete. While executing a pile foundation work around Bombay, the authors came across the peculiar phenomenon. The routine testing of water has indicated that water is non-aggressive; however, on exposing the piles, the piles were found to be highly detonated. The testing of water on the guidelines followed by engineers associated with flow through pipes revealed that water is corrosive as per the Ryznar index concept. The present papers discussess the significance of Ryznar index in under water concreting.

Jan 1, 1996

By David Forrester

Subsidence beneath the land surface has traditionally been monitored using the most accurate surveying methods of the day. Over the several hundred years of subsidence investigation, these techniques have improved, and thus the accuracy of subsidence measurements has improved. In circumstances where the subsiding surface is masked by water or rock, novel methods must be developed. This method describes the recent successes of subsidence monitoring using advanced bathymeric techniques in the Sydney Coalfield. In order to obtain subsidence profiles above submarine coal extractions, seafloor bathymetry surveys, run before and after mining, have shown that subsidence profiles can be detected, despite the primitive nature of some of the trials. Very recently, there have been considerable advances in this field, associated with the availablity of high-powered personal computers to control data collection and analyse the results. The recent surveys described in this paper have demonstrated the considerable potential for such methods. This paper describes bathymetric subsidence monitoring developed in the Sydney Coalfield, illustrated with some typical results, and summarizes the findings of the research leading to the development of subsidence design criteria specific to the Sydney Coalfield.

Jan 1, 1996

By René G. del Villar, Jules Thibault, René del Villar

"Some key control variables of industrial processes, associated with product quality, often cannot be measured directly or frequently enough to establish adequate control. In such cases, it is possible to use available measurements to provide a prediction for these process variables and use them in a control strategy, thereby giving rise to what is now commonly called a softsensor.In some industrial grinding circuits, the on-line particle size analyzer is shared between various sampling points. Therefore, for a given location, the actual measurement is only available every 10 to 20 minutes, a delay which is unacceptable for automatic control purposes. To alleviate this problem, a softsensor based on an artificial neural network has been investigated. First, the structure of the neural network and different schemes for the training process are analyzed. Then, the performance of the neural network softsensor is compared with other inferential methods such as ARMA models and Kalman filters.IntroductionGRAHM, French acronym of the Research Group on Computer Applications in the Mineral Industry at Laval University, began in 1990 a research project on Knowledge Based Automatic Control (KBAC). This project, sponsored by a consortium of eight mining companies and the federal and provincial governments, seeked to screen advanced (knowledge-based) methods for data processing (filtering, mass balancing, etc) and automatic control (model-based) for their use in the mineral processing operations and the transfer of the project results to the sponsor companies.In parallel to more academic research work, a number of case-studies have been undertaken with the cooperation of partner companies. Among such works, a very successful one has been the design and installation of a new control strategy for one of the Kidd Creek (Falconbridge Ltd.) grinding circuits. This project was related to the evaluation of a number of control strategies and the implementation of one of them, as selected by the plant management, in the concentrator.A total of sixteen control schemes were evaluated on one of the dynamic phenomenological simulators developed at GRAHM, a trademark of this research group [ l]. The calibration of the simulator models was done based on industrial data gathered by GRAHM and Kidd Creek personnel. Then, the simulator was used to test the performance of various PID-based control schemes, designed to achieve the control objectives set by the Kidd Creek personnel. The best scheme proposed called for controlling the cyclone overflow particle size by manipulating the water addition rate to the cyclone feed box and the circulating load by manipulating the circuit ore feed. The particle size analyzer (PSI-200) available for monitoring the product size, was unfortunately shared (multiplexed) among various streams of the plant, which meant a 14 min delay between two consecutive readings for any particular stream. This induced the plant personnel to choose an alternative control strategy, one which controlled the cyclone feed density instead of the cyclone overflow particle size."

Jan 1, 1996

By P. G. Semple

For the last four years, the Kilborn Group of Companies has been involved in several major projects in the Confederation of Independent States (CIS). These include the Kumtor project, the Kubaka gold project, the Kazgold project, the Aginskoe project and the Jerooy project. These projects are all in various stages of detailed engineering and construction. Western mining companies are pursuing mining opportunities throughout the world in search of ore bodies for development. The quest for profitable mining ventures has led mining companies to South America and Asia and, more recently, to the former Soviet Union. When considering the CIS, several factors should be considered. The most notable are geography, mining culture and previous mining production.

Jan 1, 1996

By C. C. Clark, S. J. Jung

Determining the correct combination of mix components and water for high-density paste backfills that have the transport and deposition properties necessary for a mining operation is a difficult task. Rheologic properties cannot be determined without conducting full-scale pumping tests, and data from existing tests tire very limited. This paper presents the findings of investigations undertaken to determine if paste-backfill rheology can be determined using existing techniques and to determine which mix and system variables have the greatest influence on transport-pressure loss. Data from laboratory-scale pumping tests were used to produce a rheologic model of flow behavior for comparison, and a statistical analysis was conducted to determine the most significant factors affecting transport-pressure loss.

Jan 1, 1996

By J. W. Rinard

This paper is intended to introduce "non engineers" to one of the more misunderstood pump performance parameters, NPSH (Net Positive Suction Head). This basic presentation and resultant review should provide a practical understanding of NPSH and what its importance is to pump operation and reliability.

Jan 1, 1996

By Ronald J. Doll, John Elkin, M. P. Evans

The application of "Alignment Free” right angle shaft mounted drive systems offers improved reliability and reduced costs for surface and underground belt convey- ors. Comparisons to conventional approaches will cover installation, operating, maintenance, and spares inventory cost savings. Various options for belt acceleration and load control on fixed and variable length (booster) belt conveyors will be reviewed for operating performance, reliability, and total cost. Lastly, a case study of a successfully operating installation will be highlighted.

Jan 1, 1996

By N. Som

The pile capacity in cohesive and granular soils depends on a number of parameters. The values of these parameters as recommended by Indian Standard Code of Practice vary over wide ranges. A designer often finds it difficult to select appropriate values of these parameters for realistic estimate of a pile capacity. The present paper makes a critical review of the values of the parameters given in Indian Standard Code of Practice and suggests a realistic approach to selecting them in the light of recent research.

Jan 1, 1996

By D. P. Bryan

An aggregate resource study was done for southern Washoe County, Nevada, which contains the Reno-Sparks metropolitan area and a population of about 300,000. The study included an inventory of existing operations, projection of future demand, identification of potential aggregate resources based on geology, and determination of economic potential of these resources. Economic potential was determined by the integration of GIS layers that included aggregate potential, distance from market, distance from major and minor transportation arteries, and elevation. The investigation resulted in a determination that resources of high quality aggregate sufficient for future consumption are present in southern Washoe county; the limiting factor for future utilization is accessibility.

Jan 1, 1996

By H. Nemutolluhi

Discussion by G.E. Agar In the April issue of Mining Engineering there is a technical note "New size laboratory ball mill for Bond Work Index determination" written by M. Nematollahi which is very confusing. My recollection is that a description of an experimental procedure should be such that someone skilled in the art should be able to reproduce the results. Applying this test to this particular article would according to me cause a failure to be registered. There are apparently three batch laboratory test procedures referred to in the article. One of these is the traditional Bond test with all its limitations such as dry grinding followed by exclusively dry screening, two attributes which fail to simulate conventional industrial grinding. There is a second procedure (NSBM) which the author is advocating as an improvement of the Bond procedure but from the description I doubt that anyone would be able to repeat the procedure. For instance, is the grinding to be done wet or dry, if wet at what pulp density, and how is the screening to he done, wet or dry or a combination? On top of that uncertainty the author refers to a simplified "Anaconda" test. No reference is provided for this procedure and in the text the results of the technique are referred to "Denver wet ball mill" results and say nothing of Anaconda results. Reply by H. Nematollahi I think that the method proposed to determine the Bond Work Index in this paper is clearly described in the paper as follows: •The method of grinding is dry (Ref. paragraph I, subject Method description); •The size of ball mill, the quantity and size of balls are noted (Ref. paragraph 1, subject Test equipment); and The test procedure is described in detail (Ref. paragraphs 1, 2 and 3, subject Test procedure). As it is noted in the paper, the test has been worked out under the same condition as Standard Bond Test with ball mill, so dry (screening should be dry also), but using a smaller ball mill and a smaller quantity of sample. Considering the above mentioned points, I believe that the method has been fully and clearly described and it ought to be repeatable as well. The Anaconda test is a method for determination of Work Index and could be done by any types of laboratory wet ball mill (Yan, R.F., et al., cf. References). I applied this method using a laboratory Denver ball mill (Ref. paragraph I subject Determining the Bond Work Index). So the results referred to Denver wet ball mill can be equated the same as Anaconda method.

Jan 1, 1996

By Norman Disley, David B. Counter, Lionel Hebert

Misfires in underground and surface production blasts can be costly. Costs can arise from loss of resource, production interruptions, having to redrill or otherwise refire the blast (a hazardous process at best), due to added secondary blasting or breakage, and/or from increased LHD maintenance costs attributable to poor fragmentation.

Jan 1, 1996