Search Documents

By Tatsuo Itou

Both sales volume of Aluminum Can and its recycling rate are remarkably increasing here in Japan. In 1993, recycled can volume was 11.78 billion cans ( 116,258 metric tons ) and its recycling rate 57.8 percent. We, MITSUBISHI MATERIALS CORPORATION. the leading manufacturer of aluminum can in Japan and our affiliated companies are very deeply involved in recycling used beverage cans ( U.B.C ) and recycling them back to can stock. In this paper. I would like to present the following; 1. Recent trend of beverage can consumption in Japan. 2. Trend of aluminum can and its recycling rate in Japan. 3. Future of aluminum can business in Japan.

Jan 1, 1995

By M. U. Ozbay, D. R. Lougher

An in-situ experimental programme was carried out to improve the understanding of the rockmass and pillar behaviour in moderately deep hard-rock mines. The experiments were carried out at Impala Platinum mines and consisted of precise levelling measurements in the footwall of the reef, stress measurements in pillars, convergence measurements in the stope, and petroscope observations in pillars. The results were analyzed using a computer program in an attempt to quantify the characteristic behaviour of the rockmass as well as the pillars. The measured off-reef displacement data were found to co11fonn to the trends obtained from elastic modelling and the correlation could be improved by modelling the small pillars with reduced modulus to simulate yielding' of the pillars. The stress strain curve obtained from analyzing the in situ results, showed that a 6x 3 xl m pillar yields without significant load shedding at peak stress levels of approximately 208 MPa. The closure measurements confirmed that the mechanism of yielding is mainly that of pillars punching into the foundations. Slight to moderate sidewall fracturing and slabbing might be contributing to yielding, but to a much lesser degree than the former mechanism, as the petroscope observation revealed the existence of an intact region beyond 0,6m from the pillar sides.

Jan 1, 1995

By Robert S. Setren, Jeffrey L. Ambs

The disposable diesel exhaust filter (DDEF) system developed by the U.S. Bureau of Mines and Industry cooperators for heavy-duty permissible, diesel-powered haulage vehicles, effectively reduces in-mine diesel particulate matter concentrations up to 95%. However, there are concerns about the hazards that exist when the filter is used in situations for which it was not designed. This work investigates the exhaust gas temperature limits to which the filter elements can be exposed without posing a safety or health hazard, such as 6re or off-gassing toxic compounds. A filter approved by the Mine Safety and Health administration and after-market filters were evaluated under varying engine exhaust conditions to determine if after-market filters pose an unacceptable hazard when used in a DDEF system. Filters were laboratory tested at engine exhaust temperatures ranging from 77°C to 290°C. Of the seven filter types tested, six appeared suitable for use on water scrubber-based cooling systems and two appeared suitable for use on dry heat exchanger type exhaust cooling systems with exhaust temperatures up to 150°C. Any filter elements used as exhaust filters on permissible diesel machines must be approved by MSHA for that application. Mine operators who wish to use an after-market filter element should request an MSHA field modification. MSHA will work with the mine and filter manufacturer to ensure its use in this exhaust system application does not pose a health or safety hazard.

Jan 1, 1995

By Zuomei Jin

The Mineralogical form of Silver in a Ag-rich complex ore was determined. In the complex sulfide ore, acidic thiourea leaching resulted in 35% extraction of silver directly. In the same complex sulfide ore, under the effect of ultrasonic treatment, 65% of silver can be ex¬tracted. After the above ore had been roasted and acidically leached of Zn and Cu, the silver extracted from this Pb-Ag residue was 96.8%. The effets of temperature, thiourea and ferric ion concentrations and partical size were examined. The leaching rate of silver from the Pb-Ag residue was diffusion controlled. The activation energy was calculated to be 10. 49%KJ/mole. The kinetic model for the thiourea leaching of silver from Pb-Ag residue was obtained and is given by, The kinetics of silver cementation by aluminium in thiourea solutions was also investigated. The activation energy was calculated to be 65. 13KJ/mole, which is reasonable fora rate-limiting surface reaction.

Jan 1, 1995

By E. Valdiviezo, J. F. Oliveira

Adsorption of residual flotation reagents onto equilibrium fluid cracking catalysts is a promising method of purification of flotation process water. In the present paper, adsorption of sodium dodecyl sulphate (SDS), dodecyl ammonium chloride (DAC) and sodium oleate onto a spent catalyst from petroleum industry was studied by analysing the residual concentration of the surfactant after contact with the zeolite catalyst. The adsorption of the DAC was rather low but SDS and sodium oleate presented a high affinity for the catalyst surface. The loading capacity was 4.2 kg/ton for SDS and 5.5 kg/ton for oleic acid. After the treatment of the loaded catalyst with a HCI 1 N solution these surfactants are desorbed and the catalyst may thus be regenerated. This would be an additional advantage to its low cost, not to mention its condition as a discarded product and its availability in large tonnages.

Jan 1, 1995

By Richard Jr. Ray, Richard Druesedow

The Virginia Operations of Consolidation Coal Co. include a diversity of mine fan configurations which have been tested to quantify pressure losses through the inlet ductwork. Airflow and pressure measurements were taken at four shaft sites to calculate losses for the 90-degree bend at the top of the shaft and the self-closing dampers or closing doors located between the shaft and fan. Velocity contours were then developed from the test data to determine flow patterns in each fan system component. In addition, yaw and pitch angles of airflow through the fan annulus were measured to evaluate turbulence levels created by various inlet ductwork designs. The test results indicate that proper design of the shaft collar and ductwork arrangement for main mine fans can substantially reduce system pressure losses and air turbulence. BY minimizing the pressure drop experienced on the surface, these design improvements enable the bulk of the total pressure developed by the fan(s) to be utilized in the mine.

Jan 1, 1995

Constraints on the mineral industry are best treated as issues that have to be understood and managed in partnership rather than in conflict with communities. TheZapopan development at Mt Todd in Australia and the Martha Hill development at Waihi in New Zealand are but two of many recent successful examples at the local level.   However, at the national level, the issues are more complex and more difficult to resolve because the most influential stakeholders are now the urban electorates and governments defer to their perceptions when making decisions and policy. In the developed countries, government policies for the development of mineral resources have been progressively eroded since the early 1970s. At the same time policies for the environment and for native land rights have generally been carried out in a way that has reduced access to minerals and increased the cost and risks for prospectors and developers (Hancock, 1995). Since the end of the Cold War, the lesser developed countries (LDCs) have introduced policies to attract investment in their mineral resources that remained undeveloped under previous unstable or hostile regimes. The increased attraction of these LDCs and the decreased attraction of the developed countries has caused many Australian and North American companies to outlay increasing proportions of their budgets and capital investment in the LDCs.   Significantly, LDC policies for environment protection do not discourage exploration and mine development, Surveys of the relative appeal of the LDCs and the traditional mining countries of the developed world, rate Chile, Argentina and Indonesia ahead of Australia and Canada in terms of risk, delays and ease of doing business (Australian Mining Monthly, February 1994).

Jan 1, 1995

By Luis W. Pommier

Large quantities of sea sludge containing halogenated organic compounds, such as PCB, oils and metals like arsenic and lead have accumulated throughout the years at the bottom of sea channels and harbors and are obstructing navigation and creating environmental problems which need to be resolved. A sludge from a California port would be dredged by suction pumps, it would be processed in a plant which would be built either on firm soil or on floating platforms. The sludge shows contents of up to 1 ppm of PCB, 15 % oil and 10 ppm of arsenic, which generates a very fetid odor. Bench scale work indicates that most of the contamination concentrates on the solid phase, in fact, only minor amounts of oil report to the sea water and can be readily removed by physical means. After separation of the sea water from the solids of the sludge by decantation, it is possible to solubilize the PCB, the oil and the metals into an organic solvent leaving a non-hazardous soil for disposal near the harbor. The PCB is dehalogenated during the solubilization process leaving a liquor solution containing the oil and metals. The oil is extracted leaving an aqueous solution containing the arsenic. Further process extracts the arsenic from this solution rendering the liquid non-hazardous. Transportation and disposal of the sludge is impractical. There are hundreds of thousands of tons of hazardous soils accumulated in each harbor, which would fill the hazardous waste disposal sites available and it would be, prohibitively expensive to do so. It is not possible to compare the costs of decontamination with a competitive method. If it were, the proposed process would be less expensive than transportation and disposal and it has the advantage of removing the liabilities from the Responsible party. After a full scale continuous pilot project is run to decontaminate a small, 500 cubic yards accumulation of this type of sludge in a California harbor, a full scale environmental project would be initiated. The decontamination of one million tons of sludge would be completed in five years.

Jan 1, 1995

By X Qiu

According to the temporal and spatial distribution of regional metallogenesis, thePacific Rim can be divided into four global metallogenetic systems. The Asia-Australia W-Sn metallogenetic belt is the typical representative of intracontinental metallogenetic systems. This belt resulted from Mesozoic and partly pre-Mesozoic tectonic magmatism, mainly related to S-type granite of crustal source that was generated by collisional orogeny combined with oceanic subduction in intracontinental and continental margin settings. Based on the concept of metallogenetic series, there is a group of mineralised ore types showing a definite spatial and temporal distribution from endogenetic to exogenetic. These metallogenetic series are widely distributed in the Asia-Australia W-Sn metallogenetic belt, and are well developed in Southeast China. Five metallogenetic series and two petro-minerogenesis evolution models have been established according to their tectonic settings, various types of granitoids and metallogenetic evolution.

Jan 1, 1995

By E. Suoninen, K. Laajalehto, L. Kartio

Efficient separation of pyrite from other sulfides is of great importance for the metallurgical performance of flotation processes. In this work Fourier Transform Infrared Spectroscopy (FTIR) and X-ray Photoelectron Spectroscopy (XPS) were used to study the surface chemistry of pyrite in depression, activation and xanthate adsorption under conditions of controlled potential. Modifications of pyrite surfaces after treatment with depressants (lime, sulfur dioxide, sodium cyanide) and after activation with metal ions (Cu, Pb) were studied. The principal adsorption product identified on pyrite was dixanthogen whose formation started at about +0.15 V and +0.25 V (vs, SHE) in ethyl and amyl xanthate solutions, respectively. Copper xanthate was formed on copper(II) activated pyrite. Activation mechanism of pyrite by copper(II) salts is likely to be electrochemical where copper occurs as copper(I) on the surface of pyrite. Effective depression is achieved by sulfur dioxide and sodium cyanide. Depression at high pH is due to formation of iron(III) hydroxides. Calcium ions do not affect the electrochemistry but adsorb on pyrite and reduce the surface sites for dixanthogen adsorption.

Jan 1, 1995

By G. Machiavelli, P. Bevilacqua, G. Ferrara, T. P. Meloy

During several years of operation in Europe, South Africa and other locations, the Tri-Flo process has demonstrated substantial improvements in dense-medium dynamic-separation systems. The reasons for this improvement are: • a high-sharpness separation due to the multistage system and the application of new concepts in the design of the regeneration circuit and in the control of the medium Theology, and • the possibility of performing two cuts at different densities using a single separation device and a single regeneration circuit. This paper discusses the above points in detail with particular reference to the multistage technology (based on the circuit analysis theory) and to the control of the medium rheology (based on recent work in the modeling and simulation of the rheological behavior of dense suspensions). Concerning the multidensity separation, information is given on the new three-stage separator where the high-density separation is performed by the first stage and the low-density separation is performed by the second and third stages. This configuration (already realized in two operating plants) was selected because no particular sharpness was required at the high-density separation, while high sharpness was required at the low-density separation. However, the configuration can be inverted or a fourth stage can be added (at very low additional cost) to provide two stages for each separating density. The importance of achieving a high sharpness separation is related to minerals (industrial minerals in particular) where the density difference of the phases to be separated is very low (as in processing of lithium ores, feldspar- and others). Information is provided on plants operating in South Africa and Canada, for the beneficiation of lithium minerals and on a plant under construction in Italy for the beneficiation of feldspar. Finally, the importance of making the separation at two densities is emphasized with particular reference to coal; i.e., producing a low-ash premium coal and recovering, in the middling, a by-product without losing heating value. Also, very important for some minerals is the production of a high-grade concentrate (at the first stage) suitable for sending directly to metallurgy (e.g., chromite ores) and the production of a low-grade concentrate that can be further treated. In this way, a higher overall recovery of the valuable mineral can be achieved, and, at the same time, a reduction of the treatment costs can be obtained. All of the above applications were once considered impossible.

Jan 1, 1995

One of the major changes in the resource industry in the nineties has been the re-internationalisation of the industry. The history of the resource business has been one of companies from the developed world utilising the cash flows from their operations to explore and develop mines in less developed regions of the world. This resource development has progressively generated wealth and economic development, which in turn, has led to a new generation of exploration and mining projects. In South America, Chile had led the way in a mining resurgence, now closely followed by Argentina, Brazil, Venezuela and Peru. Although Chile has long had a significant copper mining industry, the pre-nationalisation phase was driven by American capital; the current phase has been spearheaded by R.T.Z. - B.H.P. at Escondida with Canadian junior companies, in particular, providing major speculative impetus. The Australian junior companies have not been significant in South America.

Jan 1, 1995

By T. Knuutinen, M. Klemetti, P. Mörsky

This paper presents a comparison study done at VTT's new pilot plant facilities in Outokumpu, Finland, for chromite ore. The ore was ground in a rod mill -, a ball mill - and high pressure roller mill - ball mill circuit in the capacity range of 0.5 - 3.0 t / h. The main grinding characteristics are discussed and the quality of the products are compared from the mineralogical point of view. The benefits of high pressure roller mill comminution for further mineral processing of chromite is also discussed.

Jan 1, 1995

By W. Addy Majewski, Kenneth L. Bickel

The U.S. Bureau of Mines (USBM) and Diesel Controls Limited evaluated a new diesel emission control system on an underground mine vehicle. The system was a catalyzed ceramic wall-flow diesel particulate filter (CDPF) combined with an catalytic converter, or diesel oxidation catalyst (DOC). This paper describes the design and installation of the system on a load-haul-dump (LHD). The results of screening tests conducted by the USBM are also given. The screening tests were conducted to determine if the device's particulate collection efficiency, regeneration temperature, and effect on gaseous hydrocarbon (HC) and carbon monoxide (CO) emissions changed over the period it was being used. The system was removed from the LHD and evaluated in the laboratory after operating for 308 and 1200 hours. After 308 hours of operation, laboratory testing revealed its particulate collection efficiency varied from 41.0 to 93.5 percent, depending on engine operating conditions. Its regeneration temperature was about 415° C. It reduced HC emissions by up to 97.6 percent, and CO by up to 95.0 percent. When tested in the laboratory after operating for 1200 hours on the vehicle, no significant change in performance was observed.

Jan 1, 1995

By Robert C. Freas

Genesis 1:28 "And God blessed them and God said he fruitful and multiply and replenish the earth and subdue it and have dominion over it." Genesis 2:15 "And the Lord God made man and put him in the garden to dress it and keep it." Depending on one's perspective, these two verses from the Book of Genesis either complement one another or are in conflict. I believe that they are complementary. What they imply is that where there is privilege, there is responsibility. Privilege comes from the fact that the Lord created the heavens and the earth and he placed man on the earth to have dominion over it. The responsibility that accrues to us comes when the Lord also said that we are accountable for how we handle that which he has given us. The very nature of our responsibilities in resource utilization or, more appropriately, resource management, has changed over time as the nation's needs and priorities have changed. Thus, I have attempted to examine, from a historical perspective, how natural resource policy has evolved, where we are now and what may lie ahead.

Jan 1, 1995

By Merry N, Cocks T

The mineral exploration industry is increasingly aware of the importance of the relationship between mineralogical data and geochemical assay results. However, until recently, the cost and time constraints of most techniques for analysing alteration mineralogy have precluded detailed alteration studies. These impediments have been reduced by the development of the Portable Infrared Mineral Analyser (PIMA), a field portable infrared spectrometer that allows rapid (in field) and cost effective analysis of alteration minerals including subtle variations in mineral crystallinity and Composition.

Jan 1, 1995

By D. D. Lei, H. Sevim

In a recently developed, long-term open pit production planning model, the optimal plan is found by exhaustively searching through nested pits of maximum metal contents. A more efficient, dynamic programming (DP) based search algorithm now replaces the exhaustive search algorithm that requires prohibitively long execution time in real life cases. The logic and formulation of the newly developed search algorithm are illustrated through a small hypothetical case. An actual gold deposit is treated to demonstrate that the algorithm does indeed find the optimal production plan among all possible plans. A comparison, in terms of computational savings between the two algorithms, is also given.

Jan 1, 1995

By C A. Feebrey, R A. Duncan

The Ebor Volcano in north eastern New South Wales is an eroded example of a central-type intraplate volcanic-intrusive complex. It is of Miocene age (19 - 20 Ma) and has similarities to other central-type volcanoes in eastern Australia which may represent manifestations of sub-lithospheric hotspot activity. Thick lava flows are exposed around the Great Escarpment and are dominated by a tholeiitic basaltic suite, ranging from ol-tholeiite to qz-tholeiite to icelandite with ages of 19.2 - 19.6 Ma. On its western edge, the tholeiitic lava suite probably overlies remnants of basanite flows belonging to the Eocene (~48 Ma) Doughboy province, but elsewhere, minor alkaline basaltic lavas may be coeval with the tholeiitic suite. Several felsic bodies were emplaced into the volcano at ~19.0 - 19.2 Ma and include subalkaline and peralkaline types. The Crescent Complex is a Miocene-age, strongly differentiated mafic to felsic intrusion in basement rocks and centrally located in pre-erosion reconstructions of the Ebor Volcano. It is interpreted to be a major feeder for the tholeiitic lavas based on age and composition. Evolution of the dominant tholeiitic suite proceeded from a parental ol-tholeiite magma, through qz-tholeiite, icelandite and small volumes of felsic rocks by fractionation of plagioclase, olivine, clinopyroxene and titanomagnetite, accompanied by enrichmentof SiO2, SFeOlMgO, alkalies and HFSE.

Jan 1, 1995

By Djona M. Gaballah I.

Selective chlorination of unroasted and roasted spent hydrorefming catalysts was studied between 300 and 600°C using the following gas mixtures : C12+CO, C12+N2 and CI2+air. Such materials contain Co, Ni and Mo compounds supported by alumina and/ or silica. They also contain variable amounts of V compounds, C, S, etc., accumulated during the life time of the catalyst. Direct oxychlorination of the C+S rich sample allows higher extraction rates than those obtained by the carbochlorination of the same roasted one. It seems that the roasting step doesn't favor the economic metals' recovery. Results of the chlorination of C+S poor spent catalysts, in the presence of CO, in the chlorinating gas mixture, or of carbon added to the sample, were comparable. Cobalt and nickel chlorides were .extracted from the chlorination residues by their dissolution with acidified water, whereas molybdenum and vanadium chlorinated compounds were recovered by selective condensation from the vapor phase. The recovery rates of valuable metals as well as the selectivity were higher for the chlorination of spent catalysts than results obtained by the hydrometallurgical processing of the same sample. Results of the scale-up of the oxychlorination of the unroasted sample confirmed those of the laboratory scale. The global recovery rates were about 88 pct of cobalt, 93 pct of molybdenum and 76 pct of vanadium. The carbochlorination was applied to the recovery of W and Ti from Denox catalyst that is a carbon and sulfur free one. Recovery rates higher than 99 pct at temperatures lower than 500 °C could be obtained. This may indicate that the chlorination process can be applied to the treatment of various industrial wastes or by-product containing transition and/or refractory metal compounds A flow - sheet for the pretreatment of these materials is proposed.

Jan 1, 1995

By Federico Chavez

The process for recovering lead from battery residues used in several Mexican Plants include lead blast furnace and rotary furnaces. The formers are basically fed with recycled batteries together with the necessary additives to produce metallic lead. One of the by-products generated in the blast furnace is a dust mainly formed by lead sulfide. The rotary furnace is used to recover lead .from lead batteries, dross from the refining-alloying process and the leady fines produced in the blast furnace. This paper describes thennodynamic analysis made to the rotary furnace process to understand the effect that each component of the system has upon the lead recovery. In order to enhance the process, the influence of iron chips composition and excess coke on slag viscosity is discussed. A computer optimization program . has been developed to design the furnace charge based on material and energy balances, .together with the thennodynamic equilibrium calculation.

Jan 1, 1995