Search Documents

By Y. Y. Sheng

Plume flows created by gas injection into liquid metals have been studied extensively, however the dynamics of bubbles within the plume have not received adequate attention, particularly for large, irregular bubbles, characteristic of the processing of liquid metals. The present model uses a combined Eulerian-Lagrangian approach in which an estimated void fraction distribution is used to calculate the liquid flow field with a conventional Eulerian scheme. The trajectories of bubbles are then computed in a Lagrangian manner using the estimated flow field, and experimentally measured information on bubble drag coefficients', lateral migration due to lateral lift forces and interaction with turbulent eddies, and variation in bubble size due to break-up. Turbulence in the two-phase zone is modeled with a modified k-e model with extra source terms to account for the second phase which have been recently determined by the present authors. The computed void fraction and turbulent liquid flow field distributions are in good agreement with experimental measurements.

Jan 1, 1993

By Thomas J. Peters

The Lime Creek study area lies 100 air km east of Boise, and 70 air km northeast of Mountain Home, Idaho. The eastern boundary of the 28,000-hectare, east-west-elongate study area lies 0.2 km west of the 3,077-m-high Smoky Dome. The area is mainly underlain by Cretaceous granitoid rocks of the Idaho batholith. No mineral resources were identified, but two mines and one prospect were found in the study area. At the President and the Last Chance mines, in the southwest corner of the study area, gold mineralization occurs along steeply dipping east-northeast-trending faults and associated quartz veins, and within adjacent Cretaceous granitic rock. The mineralized material is not rich enough to mine underground, and near surface, open-pit-mineable deposit areas could not be identified. The third prospect, the Ventura, is within altered pink granite of probable Tertiary age, but metal concentrations are very low. Geothermal activity was not observed within the study area, but hot springs do occur in the Vicinity. Bedrock observed is only suitable for the most basic high bulk and low end value applications, such as crushed aggregate. Numerous sources for crushed stone occur closer to markets. Alluvial concentrate (placer) samples did not contain free gold, and no substantial alluvial bars were seen; deposits were too small to contain resources.

Jan 1, 1993

The Hyde-Macraes Shear Zone (HMSZ) is low angle, duplex thrust system that has developed in a graphitic pelite schist within the Otago schist belt, New Zealand . At Round Hill lateral ramps have developed parallel to the movement direction between+ the footwall and hangingwall shears. These structures exhibit normal oblique-slip displacement which has been an important mechanism for creating space in an otherwise compressional system. Gold-bearing quartz veins were emplaced along the boundary shears and lateral ramps during thrusting. Gold within the lateral ramps is coarse (up to 300 microns) however hanging wall cataclasite development in the boundary shears after the gold was deposited has reduced the grainzise of most of the gold to less than one micron. This bimodal gold distribution has metallurgical implications with respect to the maximisation of gold recovery at Macraes.

Jan 1, 1993

By Johnston RF

The motivation for, the structure of, and the overall features of a block release Graduate Diploma program designed for practising minerals engineers are outlined. It is demonstrated that because of the very specific subjects taught, the course has the potential to effect significant improvements in operating plant performance. Through lifting the skill level of the participants and therefore advancing their career prospects, the course can raise staff morale and improve plant performance and productivity in their work place.

Jan 1, 1993

By Jerold L. Johnson

Remediation of small-arms firing ranges is being investigated by the Naval Civil Engineering Laboratory and the U.S. Bureau of Mines. Scheduled closures of military installations, as well as the management of active ranges, require the development of methodologies for heavy metals removal to prevent their entering the surrounding environment. The impact berms contain high concentrations of metals, and the soil and vegetation surrounding the berms were found to have slightly elevated levels. The heavy metals characterized are in the form of whole bullets, a wide size distribution of free fragments, smeared lead on the surface of the soil grains, and very finely attached particles. Gravity beneficiation can remove liberated metal contamination effectively. Weak acetic acid leaching shows promise in lowering the final metal contamination to allow the ,soil to pass the Environmental Protection Agency's (EPA) Toxicity Characteristic Leaching Procedure (TCLP) criteria.

Jan 1, 1993

Since 1960, the Dongchuan Copper Mining Bureau, Yunnan Province, China, has treated copper oxidised ores by sulphidisation - flotation technique only to recover copper. In order to improve the metallurgical performances and economics of flotation, extensive development work has been carried out during the past 30 years: several specific flotation flowsheets have evolved from the originally selected `stage - grinding and stage - flotation' flowsheet to suit various ores; the overall grinding size of the ores has been increased from 80 per cent - 200 mesh to 90 per cent - 200 mesh, resulting in significant increase in copper recovery; the substitution of CaS for NazS proved to be successful in sulphidisation of copper oxidised minerals, and also in avoiding the depressing effect of Na2S on copper sulphide minerals; the application of a number of activators of copper oxidised minerals, especially ethylene diamine phosphate, has considerably improved the flotation performance and decreased the consumptions of other reagents. Finally, the combined use of sodium hydroximate with butyl xanthate has been shown to be effective in enhancing the floatability of both copper oxidised and sulphide minerals.

Jan 1, 1993

Microorganisms have been used throughout history for the benefit of mankind with some of the earliest applications being in the production of fermented foods and beverages. Reactions involving inorganic substances such as metals, sulphur and sulphide compounds were hardly ever used until the early 1900s when it was discovered that Thiobacillus ferrooxidans was capable of promoting the oxidation of metal sulphides in ores. Today, it is widely recognised that biotechnology has great potential in the minerals industries, particularly in such areas as the leaching of low-grade ores of metals such as copper, gold and uranium; removal of heavy metal ions from process streams and from liquid process wastes; and in the desulphurisation of high-sulphur fuels. Although widespread commercialisation of mineral biotechnology has not yet been achieved, it is estimated that by the Year 2000 mineral biotechnology will have a significant impact on the minerals and metal industry and will probably account for tens of billions of dollars worth of annual production world-wide. This paper examines the actual and possible future applications of biotechnology in the minerals, metal refining and fossil-fuel processing industries. Firstly, the important chemical (and biochemical) principles involved in bio-dissolution of metals from ores and solid wastes, and in bio-accumulation of metals from process and waste solutions are reviewed, including leaching practices - past, present and future. Microbial desulphurisation of coal, and microbially-enhanced oil recovery are also discussed. The practical aspects of genetics and genetic engineering, the types and characteristics of those microorganisms important to mineral biotechnology, and the current research trends are reviewed as well. KEYWORDS: Biotechnology, microbial leaching, bioaccumulation, biosorption, bioleaching, biohydrometallurgy.

Jan 1, 1993

By Sutherland R. A, Rawling K. R

The Nanisivik Mine is located 750 km north of the Arctic Circle at the north end of Baffin Island in the Canadian High Arctic, and has been in production since 1976. The paper describes the regional and local geology and the current mining and mineral processing operations, including recent innovations in each area. The Nanisivik zinc-lead deposits comprise Mississippi Valley type sulphides in a block-faulted sediment sequence of Proterozoic age. The deposits formed in two mineralizing stages by replacement of the carbonate host rock. Exploration techniques adapted to the permafrost environment include high frequency EM and ground probing radar. Core drilling is done with calcium chloride brine but trials with heated flushing water indicate potential for cost reduction. The predominant mining method at Nanisivik is room and pillar. Cut and fill is used in some satellites to the main zone. Due to the permafrost, dry drilling is employed in the underground mining. The permafrost enhances ground stability, permitting large underground openings and, as a result, the use of relatively large scale mining equipment. For power conservation, a remote control system for the ventilation fans has reduced mine power costs. The milling of the simple coarse-grained ore in an arctic environment requires special techniques in the design and operation of the plant for materials handling, utilisation of waste heat, reagent selection and tailings disposal. Regulated heavy metal contents in effluents discharged to the sensitive environment are achieved by natural processes. A recent change from sub-aqueous disposal of tailings to beach type deposition within a cell in the tailings area is reviewed. Planning closure of the property presents special problems and an opportunity for innovative techniques. Approximately 25 per cent of the employees at Nanisivik are drawn from the Inuit population of the Canadian Arctic. As the first permanent industrial activity in the High Arctic some innovative approaches to employee relations were required which have resulted in a very stable, culturally mixed community in a remote location.

Jan 1, 1993

By Ju Hao L, Jian L

A joint project between the Fan Kou Mine, the Guangzhou Research Institute of Non-ferrous Metals, the Julius Kruttschnitt Mineral Research Centre, and the Changsha Design and Research Institute of Non-ferrous Metals has implemented grinding control on a circuit consisting of two primary mills and a single secondary mill at the Fan Kou mine in northern Guangdong province, PR China. This paper describes the initial design of the control system and the changes made during its implementation. The initial design was to obtain maximum throughput at a constant product size. This was changed so that the control provided a constant product density at a set feed rate. The set feed rate is reduced when necessary to prevent overloading of critical components in the circuit. The reasons for the changes in the control strategy are discussed.

Jan 1, 1993

By Walter K. Utt

The vibration levels of the heavy machines used in surface mining are much greater than for vehicles used on highways. In order to assure the proper functioning of electronic equipment placed on the surface mining vehicles, the U.S. Bureau of Mines has conducted a program of field measurements to define their vibration environment. The information in this report is for a class of vehicle that has a blade for scraping and wheels with rubber tires. The statistical information derived from these measurements can be used as a basis for laboratory testing to qualify equipment for a surface mining vehicle of this class. The envelope that would encompass 99 pct of the vibrations encountered in normal operations is presented for each location on the vehicle. The five locations for which data were recorded are the floor of the cab, the engine, the frame, the drive train (gear, differential, and torque converter), and the axle. Tabulated data are provided for those who wish to use a different probability level. The appropriate test profile for the laboratory testing can be determined from the information presented in this report.

Jan 1, 1993

By E. De Souza, H. Heidrich

In underground operations the evaluation of blasting fume dilution times and the application of recirculation techniques require accurate determination of the concentration of toxic fumes produced by the explosive used. This paper describes a methodology for obtaining concentrations of detonation products from commercial explosives tested under typical rock confinement and looks into the development of techniques for reducing toxic gases produced by explosives. This paper also analyses the application of techniques for the removal of toxic gas which would enable reduced re-entry times, a reduction in the quantity of fresh air and the use of air recirculation techniques, thereby providing substantial economic benefits to the industry. INTRODUCTION Toxic fumes from blasting operations are among the most common and serious hazards encountered underground. The implication of high concentrations of toxic gases emitted from blasting on the mine ventilation system are very significant and, in many cases, catastrophic results have occurred. Because blasting is a routine practice underground, the mining engineer is always confronted with the problem of controlling the fumes within acceptable levels. Typical control procedures employed underground include preventing or reducing the amount of fumes liberated from blasting through the proper selection of explosives and proper blasting techniques; removing the fumes through local exhaust systems or auxiliary ventilation (dilution ventilation); blasting off-shift, or at restricted times; localizing or isolating the effects of blasting where workings are isolated or sectionalized in the ventilation system; and absorbing some of the components of the fumes using air-water sprays. Dilution is one of the most effective control measures against blasting fumes and is universally applied. However, for precise determination of the dilution times for the fumes to reach safe concentrations, accurate determination of the concentration of toxic fumes produced by the explosives used is required. Research work has been carried out in determining the types and volumes of gases produced from blasting. In the case of ideal detonations, the nature and quantity of the fumes produced can be predicted by thermo-hydrodynamic calculations. However, commercial explosives exhibit non-ideal behaviour which is enhanced by the relatively small diameters of application in underground mines. The confinement offered by the surrounding rock further complicates the situation. It is well recognized that confinement affects performance and consequently fume generation. A detailed data base of fumes generated by commercial explosives at various conditions is introduced and the effect of blasting parameters such as, confinement, shock desensitization and incomplete detonations on toxic fume production is described for a variety of commercial explosives in use today. Thermodynamic predictions on fume production by the explosive compositions tested are also presented and compared with experimental results and their significance in assessing the quantity of fumes produced is discussed. A mathematical model capable of determining dilution ventilation requirements and dilution times to reduce the fume concentrations in the blasting zone to acceptable levels has been developed and it is being incorporated into a network system so that the effects of blasting can be simulated in typical mine ventilation systems. Solutions to the problem of controlling blast fumes within acceptable levels are described. These solutions include the use of control procedures which prevent and reduce the amount of fumes liberated from blasting. The use of low fume explosives, proper blasting techniques, dilution ventilation and filtration can be combined to effectively control fume production and save on costs. The application of these techniques to enable recirculation of underground air with reduced quantities of fresh air requirements is evaluated in a case study.

Jan 1, 1993

By Mishra BK, Agrawala S

The traditional method of scale-up uses the population-balance model. In particular, the selection function values for a material are determined in a laboratory mill and a variety of correlations are used to scale these values to plant scale mills. For example, the factor D2-5L (D-mill diameter, L-mill length) appears in many power correlations. The number of collisions is proportional to the number of balls (aD2L), the frequency of mill rotation ((x 1/4D-) and effectiveness of impact ((XD), which gives rise to the 'D2.5L' expression. However, what is lacking in this expression is that it does not throw light on the intensities of collisions. In other words, the collision intensities in both laboratory and plant scale mills are implied to be identical. This fact has been very limiting. Alternatively, the collision frequencies and intensity of impacts can be computed with the discrete element code. This code computes the motion and collision of each individual ball in the ball charge. Therefore the number of collisions and the fraction of collisions in the energy range Et, E2.òòE. (collision energy density) are calculated for a given mill size and operating conditions. Then, using the breakage function determined in drop-weight experiments, the evolution of size distribution is computed for a lab mill. The collision frequency and energy density for larger mill sizes are shown. The fundamental theory outlined for the calculation of size distribution is equally applicable for the large mill, which is the basis for scale-up.

Jan 1, 1993

By J. L. Kohler

Control circuit failures contribute significantly to continuous miner downtime. The time required to put the machine back into production is a function of the time required to diagnose the problem, obtain parts, and make the repair; of these, the diagnostic time is often the largest. A microprocessor-based system with the ability to diagnose all of the common control circuit failures was designed, installed on a continuous miner, and tested. This paper summarizes the development of the diagnostic system, and provides examples of the system's diagnostic capabilities. Implementation issues and the hardware used for the prototype are briefly described. Finally, comments on the system's performance are presented.

Jan 1, 1993

During the past five years there has been a transformation in the operating costs which apply to narrow vein mining. Mechanised methods including sublevel uphole retreat and narrow vein cut and fill are now proven. Other methods, such as vein mining by horizontal drilling from a raise platform are currently being tried in Australia.The important factors which affect the cost and appropriateness of each method include: ore continuity, the planarity of the wall contacts, relative hardness of ore and wall rocks and the dip bf the deposit.Drawing on current operating costs from a number of mines and on recent feasibility studies, a methodology for estimating the costs of narrow vein mining is presented. These costs are then placed in their economic context with regard to ore grade and mining rate.

Jan 1, 1993

By Walt Meglasson

"Developing technologies in demolition equipment and processes have produced a newsophistication within the demolition industry. Yet, with increasing frequency, owners,architects, engineers, and contractors reject out of hand one of the safest and most effectivetools in the demolition industry today, specifically the use of explosives and blastingtechniques in man_made structure removal. The use of explosives in any application mustbe considered as a tool, no more or less dangerous than any other type of tool, when usedproperly. Accordingly, importance must be attached to recognizing the skill, integrity, andcare of those who use it. Massive amounts of information and help are available to assistthe rock blaster, ranging from the practical to the highly theoretical, but very littleinformation exists to guide anyone considering unleashing the power of explosives instructural demolition blasting. The planning and work required to execute such projects iscomplex, and the recognition of the different applications explosives can be applied to isthe first step."

Jan 1, 1993

By Jan M. Peter

Many of the Pb-Zn massive sulfide deposits of the Bathurst area in northern New Brunswick, Canada, are intimately associated with laterally continuous iron formation (IF) (Figure 1). This IF is a fossil laminated, exhalative, chemical sediment. Together, the IF and the Brunswick #12, Brunswick #6, and Austin Brook deposits (rightmost discontinuous horizon on Figure 1) are collectively referred to as the "Brunswick Belt". To date we have only studied the Brunswick Belt and have not examined the horizon along which the QSR, CNE and Flat Landing Brook deposits lie. The Bathurst area is underlain by the Tetagouche Group (Figure 2), a Cambro(?)-Ordovician sequence of metasedimentary and bimodal metavolcanic rocks that was intruded by mafic to felsic plutons and subsequently deformed during the Taconic Orogeny. The stratigraphic sequence consists of shales and greywackes that are overlain by carbonaceous shales and felsic volcanic and volcaniclastic rocks; these are in turn overlain by mafic volcanic and sedimentary rocks. The massive sulfide deposits and IF occur within the upper portions of the felsic volcanic rocks in close association with carbnaceous metasedimentary footwall rocks (Figure 2).

Jan 1, 1993

By Willem P. C. Duyvesteyn

A novel hydrometallurgical process for Escondida copper concentrates has been developed by The Minerals Laboratory of BHP. The Escondida Process consists of concentrate leaching, solution purification, electrowinning and residue flotation. Part of the copper will be sold as high grade concentrate and part as high purity SX-EW copper. Contrary to previous efforts for the development of a hydrometallurgical process for copper concentrates, this patented process does not advocate the total dissolution of copper. It only aims for the copper that is readily soluble in a mildly oxidizing environment with an ammoniacal or acidic lixiviant. Both lixiviants were studied, but ammonia was preferred because of fast kinetics at ambient temperatures and pressures. By controlling the oxidation potential, the formation of sulfate ions and, consequently, of an ammonium sulfate byproduct, is precluded. These mild leaching conditions also prevent the dissolution of unwanted impurities and result in the production of ultra-high purity electrowon copper. Solution purification is carried out by solvent extraction with LIX-54. The very high loading capacity of this organic results in a compact SX circuit, consisting of two loading, one scrubbing, and one stripping stage. As the organic is selective for simple copper ions, the copper amine complex is broken down and free ammonia is regenerated and recycled for leaching. High purity copper cathodes are produced in a conventional sulfuric acid based electrowinning system. One scrubbing step is needed to separate the ammoniacal circuit from the acid circuit. Limiting copper dissolution to less than 50% also provides an opportunity to produce high grade concentrates by residue flotation. Copper recoveries in excess of 98% with precious metal values reporting to the final concentrate can readily be obtained. Complete breakdown of the copper mineral- pyrite middlings results in a final concentrate grade that can be even higher than the original feed material. The Escondida Process also provides an opportunity to accept lower grade copper concentrates producing improved copper recoveries in the mill and yet high quality concentrates for marketing. The Paul E. Queoeau International

Jan 1, 1993

By M. K. Gangal, E. D. Dainty

The CANMET diesel-related work, carried out in cooperation with the Canadian mining industry, resulted in the identification of several useful R/D studies. One such study was the development of a dash-mounted alarm signal system to indicate overexposure of production LHD diesel vehicle operators to toxic contaminants in a mine environment. The resulting instrument has been called the [CO2 Exposure Meter]. This meter is particularly applicable to LHD machines because previous investigations have indicated that operators of LHDs and some haulage truck drivers are exposed to up to 200% of the contaminant concentrations measured in the general mine return air. This paper describes the development of the system which continuously monitors and displays the operator's exposure to diesel pollutants, and indicates an overexposure by an alarm light. The overexposure limits are preset by mine personnel based on carbon dioxide (CO2) measurements, which in turn are related to simultaneous spot respirable combustible dust (RCD) measurements (or to Air Quality Indices - AQI, if available). The CO2 settings are, in general, related to the engine/exhaust treatment selections, vehicle duty cycle and local ventilation rates and efficiency. The system continuously displays one of three lights: green for underexposure, yellow for caution, and red for overexposure. Overexposure can occur for several reasons, such as: reduced ventilation, malfunction of the diesel vehicle, and excessive airborne contaminants. The paper confirms satisfactory operation of the system in a laboratory-simulated mine environment, as well as in field trials.

Jan 1, 1993

By J. K. Phiri

Copper mining is the main activity in Zambia and is confined to the large scale operations, mainly on the Copperbelt. The Copperbelt covers an area of size l00km by 50 km with a total of 10 underground and 5 open-pit mines operated by Zambia Consolidated Copper Mines (ZCCM) Limited. Most of the operations in these mines involves drilling and blasting. The loading of broken materials is by both manual and mechanical operations. Among the many risk factors associated with mining on the Copperbelt, is the occurrence of Pneumoconiosis which in the recent past has become quite prevalent and thus an important occupational health hazard for the industry. This study was carried out with the aim of establishing trends of pneumoconiosis incidence through the annual data collected by Pneumoconiosis Medical and Research Bureau of the Ministry of Health in Zambia, so that a basis could be formed for future research work. The study covers over 1,000 certified cases of Pneumoconiosis between 1960 and 1990

Jan 1, 1993

Geophysical anomalies result from the passage of hydrothermal fluids through rocks. Interpretation of these anomalies, when integrated with available geological and geochemical data, assists the construction of a conceptual model of the original hydrology of the system. The original extent of a geothermal system is often indicated by the distribution of low resistivity argillic clay alteration. Quartz-adularia vein deposits, silica sinters or stockwork (often mineralised) cause local increases in resistivity. Appropriately chosen electrical techniques can therefore be used to help target such structures. Airborne magnetic surveys have also proven useful in New Zealand epithermal exploration, because hydrothermal fluids destroy magnetite causing extensive demagnetisation anomalies. Ground magnetic surveys can sometimes be useful for geological interpretation on a local scale. Positive gravity anomalies may occur as a result of mineral precipitation (silica or calcite) in high porosity host rocks, while negative gravity anomalies can result from hydrothermal fracturing and leaching of relatively dense host rocks. The relative merits of these geophysical techniques as used in the exploration of epithermal mineral prospects are discussed, with particular reference to the Hauraki Goldfield. The preferred method for defining zones of quartz veining/silicification is vector or tensor gradient resistivity. Exploration strategies and technique refinements are suggested as a means of improving the resolution of potentially mineralised target structures, in a more efficient and cost effective manner.

Jan 1, 1993