Search Documents

By B. Devulapalli

A mathematical model of the industrial hydrocyclone based on fluid dynamics is a better alternative to the currently existing empirical models. The swirling-flow velocities are determined by solving the Navier-Stokes equations with an appropriate turbulence model. The solution of the momentum-balance equations yields the flow field inside the hydrocyclone which determines the particle trajectories, and subsequently the classification curve. The essence of the model is that the physical dimensions of the hydrocyclone and the slurry characteristics can be incorporated, and the influence of these parameters reflects on the flow predictions. The predicted tangential and axial velocities in a 250-mm hydrocyclone are in good agreement with the laser-Doppler velocimetry measurements. Finally, the predicted classification curves show good agreement with experimental data measured on a KREBS Dl0B hydrocyclone.

Jan 1, 1993

By Boleslav Taraba, Antonín Taufer

Thermovision monitoring of surface temperature has been examined for the purpose of detection of spontaneous combustion of early stage. Measurements were carried out in bituminous and subbituminous coal mines. It was found that surface temperature heterogenities can be considered as common phenomenon in mine openings. However, the most of the observed temperature heterogenities were not connected with coal spontaneous combustion of early stage. These, so called [non-spontaneous combustion] temperature heterogenities in surface of mine openings were found to be caused by: l. Different conditions of heat transfer between opening surface and air stream; 2. Low temperature (natural) oxidation of coal; 3. Dissipated heat loses of working machine. Sites of early stage spontaneous combustion of coal were characterized by: 1. More significant, local rise in surface temperature comparing with low temperature coal oxidation; 2. Evolution of carbon monoxide with local concentration near the surface of such site more than about 15 ppm (bituminous coals) or 30 ppm (subbituminous coals). INTRODUCTION Mine fires are a serious hazard to life and result in a considerable loss of coal reserves. Thus, great attention is paid to investigation of new methods enabling already early detection of self-heating of coal. The earlier a fire is observed, the easier would it be to deal with. Detection methods used in coal mines are mainly based on: 1. [Mine air analysis]. Changes in composition of mine air are examined. Products of spontaneous heating of coal, not being present in mine air under normal conditions, are considered as indicators of anomalous behaviour of coal (carbon monoxide, unsaturated hydrocarbons) (Mackenzie-Wood and Strang, 1990). 2. [Temperature measurements]. Sites of higher temperature level comparing surroundings are looking for underground using various direct or indirect methods of temperature measurements. This paper summarizes experience from thermovision monitoring, as one of the latest indirect temperature measurement technique, used for the purpose of early detection of self-heating of coal in mine openings. INFRARED THERMOVISION Infrared thermovision device of AGEMA Infrared systems AB (Sweden) was used for the in situ measurements. The constant value of emissivity factor, 0.95, was pre-set as the most probable level of emissivities of coal and rocks in mine conditions.

Jan 1, 1993

By M. H. Moys

Accurate models of mill power are becoming more necessary as the design, operational, and control requirements for grinding mills become more stringent. Models of mill power are reviewed briefly, and a new semi-phenomenological model is derived. The conventional torque-arm model for mill power is combined with a model of the tendency of the load in a mill to centrifuge at high speeds, to describe mill power that can be related to several design variables (such as mil geometry, mill speed, and liner design) and control variables (such as load volume, slurry rheology, and mill speed in the case of variable-speed milling). The semiphenomenological nature of the model allows rational conclusions to be reached concerning the effect of various aspects of mill-load behaviour on mill power. The model is shown to be capable of describing reality with much greater accuracy than is achieved by empirical models such as the Bond model.

Jan 1, 1993

Before the arrival of the first Europeans, Aborigines living in the northern Flinders Ranges mined ochre - an earthy form of haematite used for pigment.The discovery of copper ore at Kapunda and Burra in the 1840s stimulated the early settlers to prospect further north along the ranges. Many of the new discoveries were not properly evaluated and companies were floated on the most tenuous evidence.

Jan 1, 1993

By Parker C. J, Mikula P. A

The excavation for the Sydney Opera House Parking Station comprises a large donut shaped underground cavern with a central sandstone pillar. The maximum effective roof span is about 19 m and the rock cover is between 7 m and 8 m. Permanent support for the roof and the various services tunnels consists of a combination of tensioned anchors, and untensioned dowels, and mesh with shortcrete and fibrecrete as the final lining. Steel sets were installed at main intersections.Fundamental to the design philosophy for excavation of these spans at such shallow rock cover was the use of monitoring to check on the adequacy of the installed support. Prior to excavation, extensometers, inclinometers, piezometers and surface settlement survey stations were installed. Underground survey stations, anchor load cells and shotcrete pressure cells were installed as excavation proceeded. Excavation commenced at the crown using an initial heading and three widening stages. Geological mapping during excavation confirmed borehole expectations, namely sandstone beds 1 to 4 m thick interbedded with thin shale units. Bedding plane contacts varied over short distances from tight partings to thick brecciated seams. Jointing was subvertical and joints tended to be bed-limited.

Jan 1, 1993

By C. L. McKenzie

American Girl Mine is located in the Cargo Muchacho Mountains in the southeastern Imperial Valley of Southern California. Production from the current open pit mine and heap leach recovery system began in early 1989. Previous mining and gold recovery took place commencing in 1987 at the Padre Madre site, situated adjacent to the American Girl site to the southwest. In mid-1990, a 790-tonne-per-day underground gold mine and mill went into production. Approximately 6,500 troy ounces of gold per month are recovered from the combined open pit underground mine operation. Copper in the form of Azurite [Cu3(CO3)2(OH)2] and Malachite [Cu2CO3(OH)2] are abundant in the mined ores (Henshaw, 1942). The high solubility of these minerals in caustic cyanide solutions has a negative impact on carbon adsorption and electrowin processes. This paper presents the results of monitoring programs, process chemistry, and control changes introduced at American Girl Mine to abate production complications in the refinery and measures taken to minimize solution gold losses in the adsorption circuit(s).

Jan 1, 1993

By L. C. E. FEIO, R. RAMSDEN

In many parts of the world deep level mining relies heavily on the use of refrigeration for providing safe thermal underground conditions. The trend in South Africa in recent years has been to locate the refrigeration plants on surface and to use these plants to chill water that is then distributed throughout the mine. The surface cooling installation normally consists of a pre-cooling tower in which water is first chilled before it is sent to one or more refrigeration plants for further cooling. Presently, the majority of these refrigeration plants use CFC refrigerants; however, to conform with the Montreal Protocol, these plants will have to be replaced or converted for use with alternative refrigerants. The optimum design criteria for installations using the new generation of refrigerants will be affected by their characteristics and are likely to be different from those currently in use. In light of these developments the industry is examining a number of alternative systems for future installations including water vapour refrigeration. Factors that affect the decision on the type of refrigeration system to be used in mine installations are reviewed. INTRODUCTION Gold mining has been carried out in South Africa for over 100 years and most of the reserves close to surface have been mined out; this has led to mining taking place at greater depths, approaching 4000 m below surface. One of the consequences of operating at these greater depths is that it is necessary to install refrigeration plants to cool the ventilation air so as to provide safe and healthy working conditions. With the current low precious metal prices there is pressure on mines to cut costs and in recent years there has been considerable effort devoted to the design of more cost effective and efficient refrigeration plants and cooling systems. In the last 10 years there have been many studies into the use of ice for specific applications (Eschenburg et al., 1986; Hemp, 1988 and Ramsden and Lloyd, 1992) and at present there are three ice making plants in operation on South African mines, each of which produces ice in different processes. In addition, detailed design studies have been carried out on the "split ammonia system" (Napier and Patterson, 1992). In this refrigeration system the evaporator is located underground close to where the cooling is needed, whilst the condenser and heat rejection system is on surface. As far as refrigeration plants are concerned the trend has been to move away from standard package units to custom built refrigeration installations. This has given the design engineer greater flexibility in the choice of key components for refrigeration installations. For example both screw and centrifugal compressors are used, the heat exchangers for the evaporators and condensers may be either plate or shell and tube, and in a number of installations evaporative condensers are used. In addition, the following refrigerants are in use, R12, R22 and ammonia. The acceptance of the Montreal Protocol and its amendments by the South African government will restrict the use of CFC refrigerants and it will be necessary to re-evaluate various refrigeration systems, including those that do not use conventional refrigerants, such as air cycle and water vapour systems, for new surface installations. Although new systems and refrigerants are being developed, only the following refrigeration installations will be compared in this paper: - a refrigeration system using R134a which has properties similar to R12 - refrigeration system using R22 or a new alternative refrigerant with very similar properties - an ammonia refrigeration system - a water vapour refrigeration system The benefits of new cooling systems are not discussed in detail, since they are largely mine specific and outside the scope of the present paper. Since the optimum design for an air cycle system (del Castillo, 1988) is dependent on the mine layout, this system is also not included.

Jan 1, 1993

By J. W. Jang, I. Iwasaki

Introduction Grinding ball wear in wet grinding is due to a complex combination of abrasion, corrosion, impact and their interactions. The ball charge is continually falling from a height greater than half of the ball mill's diameter, and contact is made with ore particles or other balls. Abrasive wear occurs through penetration and plowing of media materials from the ball surface by hard ore particles (Gangopadhyay and Moore, 1985). Electrochemical interactions between the abraded and unabraded areas of the ball surfaces, as well as between the grinding media and the minerals, occur in grinding mill pulps (Adam et al., 1986). The wear depends on the media composition, the hardness and the corrosive/abrasive characteristics of the slurry. The marked-ball-wear test method was used to evaluate the performance of grinding media under nitrogen and oxygen atmospheres. Also, the wear mode was studied by observing the grinding media surface under a scanning electron microscope. In general, grinding media of high hardness and high chromium contents were found to have better corrosive wear resistance than those of low hardness and low chromium contents (Jang, Iwasaki and Moore, 1988). The purpose of this investigation was to determine the size distribution and the shape of wear debris in a study of the wear rates and wear behaviors of grinding balls. Experimental Materials The grinding ball alloys used in this investigation were: •martensitic stainless steel (MSS; 0.96% C and 16.2% Cr), •high-carbon, low-alloy steel (HCLA; 0.89% C and 0.53% Cr), and •mild steel (MS; 0.22% C and 0.09% Cr). The mineral used in this study was synthetic corundum, because it was on hand and contained no magnetic impurities. Debris A 203- mm (8-in.) diam porcelain mill was used for grinding the corundum. The mill charge consisted of: •1200 g of 12-grit synthetic corundum, •770 mL of 0.05 mole/L Na2SO4 (61% solids), and •125 steel balls of nominally 25-mm (1-in.) diam. To minimize the debris corrosion, nitrogen was introduced into the mill. Grinding with MSS, HCLA-steel or MS balls was conducted for 2 hr at 51 rpm. The grinding time using the MS ball was varied from 0.5 hr to 2 hr in an attempt to study the debris amount and shape as a function of time. The debris was collected with a hand magnet from the ground slurry and separated from the corundum particles using a Davis magnetic tube. After the separation, the debris particles were immediately washed with acetone and then filtered and dried. Debris size analysis Buckbee-Mears 3-in.-diam, micro-mesh sieves and an electromagnetic shaker were used for determining the debris size distribution. In sieving, isopropyl alcohol was used. The debris fraction collected from each sieve was washed with acetone, dried and then weighed on an analytical balance. [ ]

Jan 1, 1993

By M. Z. Dogan, M. S. Celik, G. Onal, O. Ozcan, I. Yildirim

A fluorite ore (51.85 % CaF2) containing high contents of calcite, quartz and iron oxides was upgraded by flotation using a new reagent, oleoyl sarcosine (OS). In addition, quebracho and sodium silicate were used as depressants for calcite and quartz, respectively. The effect of pH, collector and depressants concentrations on grade and recovery was determined with the aim of optimizing the flotation conditions. Application of the two-stage cleaning achieved a concentrate assaying 92.17 % CaF2 with 80.1 % recovery. The Si02 content (0.76 %) was below the required level of 1 % SiO2. The mechanism of interaction between OS and fluorite, as compared to oleic acid, is also elucidated based on the zeta potential measurements.

Jan 1, 1993

By B. J. Arnold, C. D. Harrison, R. A. Lohnes

More than 544 Mt (600 million st) of coal are handled annually for use by this country's coal fired power plants. Coal is transported in various ways: overland conveyors, railcars, trucks and barges. It can travel short distances or thousands of miles, picking up moisture, freezing or drying. When the coal is received at the power plant, environmental problems with fugitive dust and further handling problems can arise. To ensure that power plant availability is not jeopardized by coal handling problems, the Electric Power Research Institute's (EPRI) Coal Quality Development Center (CQDC) developed a research program aimed at addressing utility coal handling problems. The program has identified key areas, and is investigating the cost and cause of coal handling problems as well as the solutions to these problems. The ultimate goal of the program is to develop a "handleability index" that utilities can use in their coal specifications or hardware for a utility's sampling system to predict handleability and determine if a coal shipment should be accepted.

Jan 1, 1993

In 1965, Peter Flawn author of the famous text-book on Mineral Resources (1966) published a paper in Economic Geology with the delightful title `Who took the `Economic' out of Economic Geology?'. He opened this most interesting article with the following paragraph:If one were called upon to cite an example of a fish out-of-water he could hardly pick a better one than a recent graduate of geology of an America university who is suddenly faced with the responsibility of evaluating or appraising a mineral property. And I venture to say that the 'ftsh' with a doctorate - even in economic geology - is not much better equipped than one holding a lesser degree. The new graduate with a major in economic geology probably knows the significance of the various sulphur isotopes, he surely knows a great deal about the chemistry of the ore forming fluids and he recites with ease the arguments which prove deposits are epigenetic rather than syngenetic. However he is a rare bird indeed if he knows anything about the economics of the mineral industry. The truth is that geologists who are engaged in evaluation work are largely self taught. I ask my more distinguished and experienced colleagues - `Has it always been this way? Who took the `economic' out of economic geology?

Jan 1, 1993

In the wake of the United Nations Conference on Environment and Development (UNCED) held in Rio de Janeiro in June 1992, evolved AGENDA 21. This document which was adopted at the Conference, provides a global action guideline for sustainable development into the 21st century.Sustainable mining requires a complete understanding of the `mineral cycle', including government legislation, mineral exploration, mining operations, rehabilitation, product use, re-cycling and waste disposal that takes into consideration associated social and environmental considerations and achieves economic objectives.

Jan 1, 1993

By Ian S. Lowndes, Adrian T. J. Moll

With the current trends towards the concentration of extraction to fewer but higher production units in deeper seams, often of higher coal rank, the role of methane drainage ranges has become critical. As mines exploit seams at greater depth and more remote locations there has been a need to extend the lengths of methane drainage ranges and to increase the capacity of the surface pumps. This trend has highlighted the need to effectively simulate the operation of a methane drainage range in order to produce the optimum design and operation of a safe and economic system. This paper describes the development of such an analytical tool. The application of this computer model is illustrated by the analysis of the operation of the drainage system of an extensive mine. The paper concludes by considering the development of a [Knowlege Based or Decision Support System] which will assist the ventilation engineer in assessing the current performance of an existing drainage range and will suggest possible remedial modifications or design strategies which may improve the system performance. INTRODUCTION In order to maintain the general body methane levels to below predetermined statutory threshold limit values (TLV's) on major longwall production units there are, for a given production rate, two major complementary control devices which may be employed by the ventilation engineer. These are the combined design and application of a competent mine ventilation and methane drainage system. The methane drainage system should be designed so as to maximise the capture of the methane (firedamp) from the seam being mined and the strata gas liberated in the vicinity of the extraction zone from gas bearing seams or other reservoirs of gas situated at above or below the mining horizon. The design fresh air quantity entering the face should ensure that under normal operating conditions the methane entering in the vicinity of the face is rapidly dispersed and dilute to well below statutory TLV's. The drainage system must therefore be designed to maximise the capture of the methane gas liberated to minimise the amount of gas which enters the ventilation airstream. GAS DRAINAGE The inherent dangers of methane emissions in mine workings have been a problem of concern to mining engineers for many years. To alleviate the risk, methane drainage has been employed for some years to capture the gas before it becomes a hazard to the operation of the mine. The method of drainage employed will be dependent on a number of factors which include the longwall mining method and production cycle employed, the characteristics of the coal seam being extracted and those of the adjacent gas bearing strata. The location of the gas bearing potential of the over and underlying coal measures must be determined. The gas bearing

Jan 1, 1993

By W. B. Greer, J. J. K. Daemen

Introduction The performance of seals in boreholes, shafts and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall et al., 1982). This research involved the installation, extensive hydraulic testing, removal and post-test examination of a 10-cm-long x 10-cm-diam cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble Peak in the Santa Catalina Mountains, AZ. A test hole was diamond cored in the recrystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diam, and dips at 10.4°. The hole extends between two drifts and thus is accessible from both ends. Seal installation Surveys to assist in selecting the interval to seal consisted of core logging, video logging and constant-head injection tests using a straddle-packer unit. The location selected, 3 m from the lower end of the hole, had low hydraulic conductivity (3 x 10-10 to 3 x 10-9 cm/sec) and was free of significant fractures. The grout used, an expansive Class A cement, was provided by Dowell-Schlumberger, Tulsa, OK. A grout mass about 1.5 m in length was installed, with a dump bailer, above a temporary mechanical plug. Groundwater in the hole, if any, was minimal during placement. After 13 days of curing, the grout mass was partially drilled out from both ends, leaving a seal 10 cm long. Water distribution in rock mass The distribution of water and fluid pressure in the rock mass near the seal appears to be complex. The generally dry condition of the borehole and rock mass suggests that the rock mass near the seal was unsaturated prior to the injection tests of this research. The injection tests presumably created an expanding saturated zone around the seal. However, anomalously high fluid pressures, consistently recorded by one of two piezometers installed near the seal, suggest connection to a source of significant natural hydraulic head. Comparable head variations for closely spaced piezometers have been reported by others (Sowers, 1976). [ ] Seal testing The seal was tested for 3.5 years, using steady constant-head, tracer travel-time, dye-injection, head-buildup and transient constant-head tests. These tests are fully described in Greer and Daemen, 1991. In the head-buildup test, transient flow occurs through the seal (and rock mass) to a closed, water-filled interval of the borehole adjacent to the seal. The test consists of monitoring the rise in head in the closed interval until steady conditions are approached. The test may be analyzed in terms of a one dimensional analytical model to obtain the effective hydraulic conductivity (Ks) and specific storage (Sss) of the seal. Analysis in terms of an axisymmetric three-dimensional numerical model may yield properties of both the seal and rock mass.

Jan 1, 1993

By S. L. Jung, T. L. Nichols, K. Prisbrey

The problem was to evaluate the on-line detection of rock properties through acoustic emission sensors. Acoustic emission sensors, when attached to crushers, grinders, and roof bolters, are robust, economical, and relatively maintenance free. Our objective was to relate acoustic emissions to rock fracture mechanisms, including micropore closures, linear elastic deformations, and crack propagation. We evaluated acoustic emissions from steel jacketed rock cores during indentation tests. In addition we attached sensors to the rotating shaft of a rock bolter drill. A back propagation neural network "learned" rock fracture characteristics and rock type with 99% classification accuracy. A neural network's calibration and computational abilities suggest better acoustic emission sensor capabilities.

Jan 1, 1993

By K. A. Natarajan, M. K. Yelloji Rao, P. Somasundaran

The bacterium Thiobacillus ferrooxidans triggers the surface modification of sulfide minerals to provide hydrophilicity or hydrophobicity for the flotation of sphalerite and galena. The effects of initial cell concentration, period of biotreatment and pulp density on the floatability of the minerals are discussed. With galena, flotation enhancement obtained through sulfuric acid treatment was retarded by biotreatment at all cell concentrations due to chemical effects. Such a decrease occurred for sphalerite only at cell concentrations sufficiently high for bacterial attachment to the mineral surface. The variables affecting surface modification (and, thus, flotation response of the minerals) include the cell concentration used for bacterial conditioning, the period of biotreatment and the pulp density. Although bacterial growth during biotreatment was observed even in the absence of nutrients, such growth was more common in the sphalerite suspension than in the galena suspension. Cell protein estimations suggest that more cells are attached on galena than on sphalerite. Probable reaction mechanisms associated with bacterial modification are discussed.

Jan 1, 1993

By J. E. Litz

The hydrometallurgy review did not arrive in time for publication in the May issue. 1992 was not a banner year for hydrometallurgical installations or new hydrometallurgical developments. Installation of copper solvent extraction/electrowinning circuits were under construction or began operation in Nevada (Yerrington ), Arizona (SilverBell), Chile (Copiapo and Escondida), Peru (Toquepala and Cuayone) and Australia (Girilambone). These installations will produce more than 100 kt/a (110,000 stpy) of cathode copper. Several new heap leach gold facilities using conventional technologies were announced or were put into operation. New technologies undergoing widespread testing include biological oxidation of low-grade ores in a heap leach mode and evaluation of new agglomerating agents.

Jan 1, 1993

By L. Xu, A. Vazirnegad, R. Bhaskar

"Respirable dust samples are collected by the U.S. Mine Safety and Health Administration (MSHA) and mine operators as part of the requirements of the Federal Coal Mine Health and Safety Act of 1969. About 1.85 million respirable dust samples collected by MSHA were analyzed for the period 197/ to 1990 f or the states of Alabama, Colorado, Illinois, Kentucky, Ohio, Pennsylvania, Utah, Virginia, and West Virginia. Trends in coal dust exposure of continuous miner operators, helpers, and roof bolters were analyzed. The reported production in each of the nine states was analyzed. The relationship between average dust exposure and coal production was evaluated. In addition, the differences between mine operator and MSHA inspector collected data were examined for each state. The average exposure levels for the three occupations - miner operator, miner helper, and roof bolter were also compared.The data indicate that the dust exposure levels have significantly dropped over the last twenty years, while at the same time production has increased, attesting to the ability of the U.S. mining industry to adapt successfully to the stringent dust control regulations. In terms of coal production, it appears that some states, such as Utah, Illinois, and Kentucky, were able to increase their production significantly relative to others, such as Pennsylvania and Virginia. The relationship between dust concentration and coal production is, at best, tenuous. 11 implies that existing dust control technology has assisted several mine operators to meet dust standards, while, at the same time, enabling mines to produce more coal than before. Comparison of data collected by MSHA and mine operators indicate that MSHA inspectors recorded higher dust levels and lower shift production relative to mine operators."

Jan 1, 1993

In 1992, the United States economy grew at a rate of 2%. The Gross Domestic Product rose to $5,946 billion. With 257 million people - 635,000 in mining including petroleum - the United States has more than 100 million dwelling units and more than 190 million licensed motor vehicles. New private housing starts rose I 1 % to 1.2 million units. New car production rose 4% to 5.7 million units. Truck and bus production rose 20% to 4 million units. The rate of inflation was 3.5% and the prime rate of interest was 6.25%. The Producer Price Index (1982 =100) was relatively unchanged from 1991 as follows: fuels and related products and power 80, metals and metal products 119, chemicals and allied products 126 and nonmetallic mineral products 117. Energy Imports of crude and refined petroleum, costing $50 billion, rose 3% to 455 Mm3 (2.9 billion bbl). Domestic petroleum production fell 1 % to 582 Mm3 (3.5 billion bbl). Petroleum supplied about 41 % of US energy, natural gas 24% and coal 23%. Coal production, 60% from surface operations, rose 1 % to 914 Mt (1 billion st). About 78% was used to generate electricity and 3% was coked. Exports valued at $4 billion included 57 Mt (63 million st) of metallurgical coal and 39 Mt (43 million st) of steam coal. Ura¬nium mining, including recovery from phosphates, fell 18% to 3 kt (3300 st) U308.

Jan 1, 1993

By Ernest Peters

To model the zinc pressure leach, equations have been written that describe the rates of individual reactions taking place, including (a) oxygen mass transfer, (b) ferrous oxidation by dissolved oxygen, and (c) ferric reactions with ZnS and other minerals. In the continuous process, at steady-state, these take place at the same rate, and so the equations can be solved simultaneously. Model calculations using simultaneous equations are shown in graphical form to demonstrate the effect of different variables on the leach performance.

Jan 1, 1993