Search Documents

By King R. L

Low-enthalpy geothermal groundwater resources occur at relatively shallow depths in the Upper Cretaceous/1'ertiary sedimentary sequence in the on-shore Gippsland Basin. The main stratigraphic unit containing hot groundwater is the Latrobe Group. Groundwater temperatures in the range 30 to 70¦C have been recorded from depths between 500 and 1000 m. The hottest groundwater is in the Latrobe Valley and Lake Wellington depressions. Geothermal gradients in these areas range from less than 2¦C/100 m to over 10¦C/100 m (compared to a world average of about 3¦C/100 m). A number of theories have been advanced to explain the geothermal anomalies including exothermic reaction such as oxidation of coal, mixing with deeper, hotter groundwater and high geothermal fluxes along fault zones. Variations in geothermal gradients can also result from type and thickness (and hence thermal conductivities) of the sedimentary pile, depth to consolidated basement rocks, and influence of groundwater flow patterns including proximity to recharge zones. The hot groundwater in the Gippsland Basin has substantial potential as a source of energy for direct heat applications such as process heating, space and water heating for buildings, and agricultural and aquaculture. Geothermal energy has a number of environmental advantages over traditional sources of energy. It is clean, safe, causes minimal land disturbances and in most cases is naturally renewable.

Jan 1, 1992

By J. S. Jaspal

Mining of thin coal seams is both difficult and uneconomical. As a result, most of thin-seam coal reserves in the U. S. are not being mined. It is estimated that nearly 910 Gt (K. Unrug, 1985) of coal reserves exist in 355 to 710 mm thick seams. The Bureau is attempting to develop new techniques for mining 150 to 1065 mm thick coal seams. This paper summarizes the research work on existing thin-seam mining techniques, testing on small and full scale physical models of the Bureau slot mining concept, and computer modeling of the full-scale process.

Jan 1, 1992

By M. Z. Rashad

The purpose of this work is to determine the influence of sample length or size on the value of variance (Semi-variogram) to select the suitable length that is required to the geostatistical computations of ore evaluation. Three cases in Ghorabi Iron Ore were studied. The first one was on the iron fraction (Fe\) at which the semi-variogram gave an evidence to good continuity of the fraction in the ore. In this case, the length of sample has not important influence. The second case was for the Mn\ component of the same area where the semi-variogram has a nugget effect. The selected length for this case was 4 meters. The Cl fraction of the ore was the third case where the anisotropic phenomena was appeared and the suitable length is 3 meters.

Jan 1, 1992

By J. D. Ecuyer, L&apos

he microstructure of galvanneal coatings formed on extra low carbon and interstitial free steel substrates has been characterized using electron microscopy (TEM and SEM) and x-ray diffraction. The coatings are found to consist of a mixture of gamma, delta and zeta phases, of which delta is the main constituent. The amounts of each phase influences the powdering resistance of the coating which was evaluated using reverse Olsen testing and 60" bending. For the three heat input conditions considered, IF coatings were always found to contain a significant amount of gamma and only those which retained zeta phase on the surface exhibited a satisfactory powdering resistance. In much the same way, ELC coatings with relatively thick gamma layers performed satisfactorily only when some zeta was retained. It was also found, however, that coatings with minimal zeta and gamma had an excellent powdering resistance. The latter coatings were produced under galvannealing conditions of lower relative heat input. These results indicate that in addition to the zinc bath composition, coating weight and galvanneal thermal cycle, the base steel chemistry also has an effect on the coating microstructure. Knowledge and control of all aspects of galvannealing is therefore essential to consistently produce acceptable coatings.

Jan 1, 1992

By Betty L. Gibbs

A short course, held during the SME Annual Meeting in Phoenix, AZ in February, focused on software for surface and underground mine modeling. The objectives of the short course were to review techniques for surface and underground mine planning. Mine planning software vendors were invited to demonstrate how their software runs, given a standard data set. Six vendors of mining-specific software participated in the workshop. They were Exploration Computer Services (MINEX 3D), GEMCOM Services, Inc. (PC-MINE), KJRA Systems (VULCAN), Mine Development Associates (SURPAC), Micromine and MINEsoft (TECHBASE). Data set A data set was created to challenge the capabilities of each vendor's software. The criteria used for the data set selection were: • a minimum of 300 drill holes; • the data must include topography, drill hole survey, assay and formation contacts; • the deposit was multimetallic; and • there was the potential to be mined by surface and underground methods. The data set used was an actual, complex copper ore body with a small amount of gold. The ore body was close enough to the surface to be mined by surface techniques. Part of it, though, was also amenable to underground mining. To further complicate the problem, a river ran across the area of the ore body. This presented mine planners with the problem of either moving the river or mining around or below it. The ore body had not been mined, so no data was available for the tons and grade actually produced. Data for the mine planning problem was distributed to each vendor about two months before the short course. They had the opportunity to load the data into their systems, build an ore body model and perform preliminary work. During the first day of the workshop, the vendors received problems concerning the ore body. They went to work on their machines, attempting to show short course participants how their software could help solve the problem.

Jan 1, 1992

This paper outlines the aims, objectives and means by which a life of mine land use plan was established for Comalco's bauxite mine at Weipa. Comalco realises the need to strategically plan for future mining activities and still minimise the impact of operations on the natural resources of the region. With this realisation long-term forward planning has been implemented to improve the Company's ability to select future sites for mining, industrial use, agriculture, town expansion and conservation purposes.The knowledge of mineral, water, soil and animal resources has expanded dramatically in the past decade. During 1990 Cornalco purchased Geographic Information System technology which has allowed previously collected resource data to be presented in map form. These maps as part of the Life of Mine Land Use Plan are both information based and strategic which can be efficiently updated. The maps allow a broad audience from engineers, geologists, environmental scientists and site managers to government officers and the general public to comprehensively view and scrutinise the operations.

Jan 1, 1992

The theme of this conference is æRediscover OtagoÆ and the conference occurs during a resurgence of economic activity in New Zealand, and in particular at a time when the Macraes Gold Project has had a significant effect on mining and business activity in Otago. The Macraes Gold Mine has implemented a Zero Accident Programme and this paper reviews some of the factors responsible for the implementation.

Jan 1, 1992

By Bin Du

In recent years, concurrent product design and process is gaining popularity and will become a norm of the industry of the future. Forging has been a critical manufacturing process for production of components with superior tensile strength, toughness and grain flow. This paper describes an expen system which is being developed for forging die design and forging process analysis in concurrent engineering environment. Rules and guidelines pertaining to forgeability are formulated and incorporated into the knowledge-base in building the system. The system is built using an object-oriented paradigm. The object-oriented approach and hierarchical rule structure paradigm are briefly discussed. Finite element analysis packages (ALPID-2D) were incorporated into the program to give the simulation result of the forging process. The system can automatically produce a competent design and recommend a set of processing parameters for a given product. The designer can modify the design according to the result of the simulation.

Jan 1, 1992

By D. A. Knight

The property is located in the Porgera Valley 600 Km North West of Port Moresby. The remote location is 2500 m above sea level. The mine area has 3,600 mm of annual rainfall and a temperate climate with temperatures ranging from 10" C to 22° C throughout the year. Alluvial gold was reported in the Porgera area in 1938 and has been an important source of revenue for the area for many years. Intermittent exploration was carried out until the 1960's when Placer (PNG) Pty. Ltd. with Mt. Isa Mines commenced an extensive exploration program. The property was brought to production in 1990 by the Porgera Joint Venture group consisting of Mount Isa Mines Ltd, Rennison Goldfield Consolidated Ltd. and Placer Dome Inc, each with a 30% ownership and the Government of Papua New Guinea with a 10% share. Placer Dome Inc. is the manager of the property with construction under the direction of the Placer Dome Technical Services group.

Jan 1, 1992

By I. R. Miller

The purpose of this discussion is to try to offer some suggestions as to how the zinc and lead markets will perform over the balance of the decade, review some of the factors influencing production and come to some conclusions regarding prices. The past 2 years have been simply awful in terms of consumption, prices and overall profitability for the industry. In looking ahead to the year 2,000, it is probably not a bad idea to look back about 20 years to see where we have been and how we got to where we are. Zinc consumption from 1950 to the early 1970's increased steadily and rather nicely at an annual average rate of close to 4.0%. It was starting in the early 1970's that things started to get volatile and at times, difficult for the industry. The general economic boom of the early 70's was marked by annual consumption rates close to 5.0 million tons, a level not seen again for over 10 years. The First Oil shock of 1973-74 was followed by the sharpest consumption drop in memory. In two years, Western World zinc consumption fell 27%. While our chart shows a rather dramatic recovery thereafter, the average annual growth rate since 1970 has only been a rather modest 1.5%.

Jan 1, 1992

By Mortimer J. Richardson

Dredging can be traced to early times where it may have been derived by the Phoenicians prior to the 4th century B.C. The first tangible design drawings of a bucket ladder (BL) dredge can be found in the collections of Leonardo da Vinci (1452-1519), which he produced when he was attempting to create better methods of channel and port dredging. The perfection of the system did not commence until after the invention of the steam engine in the early 1800's; providing the impetus to progress from man-powered mud mills, horse drawn along polders or dikes in the Netherlands, England, France and Germany, to steam-driven. In the 1860's following the various gold rushes in the U.S., Australia, New Zealand, Siberia and South America, with placers in particular, efforts were begun to apply mechanization to achieve deeper digging. There is a recording of a dredge being installed to mine gold in Montana in the 1860's but did not include a processing system. Then in the 1880's in New Zealand, some practical engineers developed a system that is said to be the first bucket ladder mining (BL/M) dredge for mining gold placers. In studies of the New Zealand gold dredging experience, it is estimated that some 500 dredges were built to mine gold between the 1880's and 1942. A careful analysis of the data, however, shows that very few were profitable. The technology appeared to stagnate in the early part of the century. Two of the BL/M dredge design engineers left New

Jan 1, 1992

By Sean Gallagher, Thomas G. Bobick, Richard L. Unger

This paper describes research by the Bureau of Mines on alternative materials-handling strategies for reducing the costs and incidence of back injuries in low-seam coal mines. Strategies recommended for redesigning materials-handling tasks include elimination of tasks, mechanization of tasks, and matching lifting tasks to the physical capabilities of underground miners. The report also discusses other methods that can be used by management to reduce the costs associated with back injuries. More detail can be found in Bureau of Mines Information Circular 9235 (Gallagher et al. 1990).

Jan 1, 1992

By A. G. Pasamehmetoglu

This paper describes the conver¬gence and load measurements carried out in inclined seams at five longwall faces, two of which were supported by hydraulic props and the other three by conventional timber supports in Karadon-Gelik mine. The minimum support capacities determined in this study are compared with the results obtained from two empirical approaches suggested by Wilson (1975) and Jacobi (1981). The characteristics of hydraulic props to be used and support patterns in the longwalls are found, conclu¬sions are drawn and suggestions are made. Design nomograms are prepared for field engineers, in order to be able to approach the problem more confidently and realistically.

Jan 1, 1992

By Michael D. Balen

During the years 1987 through 1989, the Bureau of Mines Alaska Field Operations Center (Bureau) in cooperation with the Western Field Operations Center and the Alaska Division of Geological and Geophysical Surveys (ADGGS), conducted mining, geological, and geochemical investigations in the 5.7 million-acre Valdez Creek Mining District (VCMD). This investigation was conducted as part of the Bureau's continuing Mineral Land Assessment (MLA) mining district studies program. The Bureau's MLA program is designed to provide reliable and comprehensive mineral resource information that supports mineral resource policy and land use decisions made by Congress and Federal land management agencies. The information also provides the basis for decisions that would expand the domestic supply of important mineral resources, primarily strategic and critical minerals. Much of the MLA work is done jointly with cooperating State or U.S. geological surveys.

Jan 1, 1992

By P. E. Damon

An arsenal of isotopic techniques is avail-able that can date the full range of hydrothermal ore deposits. The following are prerequisites for ideal results: (1) Careful collection of samples that are related to the event in a field and process context; (2) Optical examination of the component selected for dating to be sure that it has not been altered; (3) Careful preparation of a pure component of the sample selected for dating; (4) Precise and accurate measurement; (5) Knowledgeable interpretation of the data with reference to decay systematics, properties of the component analyzed as well as the field context and thermochemical environment of the ore process.

Jan 1, 1992

By T. N. Moore, E. M. De Souza

J. Dasher Regarding the March 1991 ME technical paper by De Souza and Moore: For more than a decade since my February 1981 article on how to use modern metric, which SME-AIME had decided to do, I have monthly pointed out metric errors to the editors. In part, I do this because there has been no action to allow editors to fix figures and tables or to allow them to require authors to do so. The latest resulting atrocity provokes this discussion of vibrating drill handle units being stated in decibels. Reply by T. Moore We have read the discussion of our paper by Mr. Dasher. Our reaction is one of surprise and incredulity. It would seem that Mr. Dasher takes exception to the use of the decibel scale to present vibration acceleration data, and the use of hertz as the unit for frequency. The basis for his objection to the decibel appears to be that it has no dimensions (which somehow invalidates its use), that it is "non-metric" and, finally, that it is parochial (of limited or narrow scope). His objection to the use of the term hertz is not stated, but we will assume that it stands condemned as "non-metric" and parochial. Obviously we disagree with Mr. Dasher's views and will now outline our reasons. Although the decibel scale originates from transmission line theory and telephone engineering, it is also at present widely used, not only in the fields of electronic engineering and acoustics, but also in the area of vibration. The original definition of the decibel (dB) was based on power ratios: dB = 10 log 10(W/W0) where Wo is a reference power. However, as the power measured across a given impedance is related to the square of the force acting upon this impedance, Z, a more commonly used definition is: [2 dB = 10 logF /Z) = 20 log F/F 10\ F0 2 /Z(0)] where F and F0 are the r.m.s. values of the forces. Now, if the measurements are related to one and the same impedance, the decibel notation in the form of 20log10(X/Xo) may be used as a convenient relative magnitude scale for a variety of quantities. Thus, X may, for instance, be an r.m.s. displacement, velocity or acceleration. It is only required that XD always be a reference quantity of the same type as X. That is, when X represents an acceleration, then X0 represents a reference acceleration. This is the formulation used in our paper. This was not an arbitrary choice on our behalf but reflects standard practice as specified in the International Standard ISO 5349-1986(E) Mechanical Vibration - Guidelines for the Measurement and the Assessment of Human Despite the metric prefix, the decibel is a parochial expression of (l) the logarithmic ratio of the loudness of a sound to what is normally audible or (2) the logarithmic ratio of two power signals in radio or electronics. A decibel is not a unit, much less an SI, unit and has nothing whatsoever to do with the acceleration of drill handles. Stating that m/s2 (acceleration) is decibels is without reason. Whoever reviewed this material should not have allowed publication of figures of dB and H.[ ] Exposure to Hand-Transmitted Vibration. This was clearly stated in the "measurement protocol" section of our paper. This quantity is then referred to as the acceleration level and is expressed in dB. We may have inadvertently caused some confusion when we simply used the term acceleration to refer to acceleration level on our diagrams. At the time, we felt the use of dB or m/s2 would make the context clear to the reader. For any confusion this decision may have engendered, we apologize. Since the decibel expresses the ratio of two like quantities, it certainly has no dimensions. It is, however, common practice to treat "decibel" as a unit as, for example, in the sentence, "The acceleration level measured at the operator's hand was 160 dB." The expression of measured quantities in dimensionless form is not inherently unacceptable. In fact, in many areas of engineering it is standard practice (consider the use of Reynolds Number, Nusselt Number, etc.). The fact that the decibel is a dimensionless quantity makes the question of whether it is a SI unit nonsensical. However, it is valid to insist that the dimensional quantities used to obtain the decibel values be expressed in SI units. A careful reading of our paper will make it clear that the measured acceleration was, in fact, expressed in units of m/s2 as was the reference acceleration (l x 10-6 m/S2). These are the accepted derived SI units for acceleration. See, for example, the standard ASTM E380-89a Standard Practice for Use of the International System of Units (SI) (The Modernized Metric System). Concerning Mr. Dasher's implication that hertz (Hz) is an unacceptable unit of measure for frequency, we would again refer him to the standard ASTM E380-89a. Here, he will find (section 2.4.2) that hertz is an accepted "special name" for the derived SI units-1. This is in keeping with numerous other international standards including ISO 5349-1986(E) to which we referred in our paper. In conclusion, we agree with Mr. Dasher on the desirability of expressing measurements in modern SI units. But we would remind him that the standards that define the use of these units, and the accepted means of presenting measured data, are in a continual state of refinement. It is, therefore, incumbent upon him to keep abreast of these changes if he wishes to constructively critique the work of others.[ ]

Jan 1, 1992

By Grynberg H, Lindon P, Wardrop J

The Gippsland Basin is unique in Australia in that it is a major resource based industry centre within a sensitive and special environmental context supplying Melbourne, a major urban/industrial environment with most of its energy 'on-line'. The environmental effects of the supply systems are generally local and mostly affect only those who are directly or indirectly dependent on the upstream systems. The major urban metropolis which is served remains largely unaware of the environmental impacts of the system upon which it is dependent, except when specific attention is drawn to them as in the case of the Latrobe Valley Outfall, algal blooms in the Gippsland Lakes, etc. This paper discusses the environmental context within which the energy industries operate, the environmental legislative framework which applies, the likely environmental impacts and some solutions. The energy resources of the Gippsland Basin occur in an area where the physical environment exhibits a wide variety of inherent energy states in its physical and biological regimes. The off-shore regions of the oil and gas platforms has to be able to withstand the wind and wave energy generated in a shallow sea in a confined waterway lying athwart the main current and climatic stream. The coastline includes the delicately balanced quiescent environments of Corner Inlet with its 'wilderness' tourism industry and the powerful surf and long shore drift and dunes of Ninety Mile Beach.

Jan 1, 1992

By William J. Wuest

This U.S. Bureau of Mines report presents an overview of ground control considerations associated with floor heave. Factors affecting heave, such as in situ stress, floor characteristics, and mine geometry, are described. Floor-displacement monitoring and data analysis methods are outlined. Finally, floor heave remediation is discussed. The remedial techniques are divided into four categories: mine maintenance, supplemental support, mine structure, and techniques for multiple-seam operations. Other subjects covered in the report include laboratory and in-place testing of floor rocks, U.S. and international case studies, effects of mine layout, determination of excess horizontal pressure, and types of heave failure. The emphasis of this report is on practical considerations; theoretical discussions are kept to a minimum.

Jan 1, 1992

By Michael E. Kovach

This discussion is an overview of an approach to drilling and blasting angle holes at Martin Marietta Aggregates. Method of determining burdens, hole depths, angle settings and explosive selection will be discussed in detail with an emphasis on safety and production. Such techniques and methods involve the use of hand-held surveying instruments such as the Abney level, pocket transit and inclinometer along with measuring tape and burden pole. An interesting method developed by Oscar Banfield a retired Martin Marietta and E. I. duPont engineer, for setting the proper angle on a drill will also be presented. This treatise is a discussion of the use of simple yet important tools and techniques a blaster should use to resolve both routine and complex problems encountered during quarry blasting operations.

Jan 1, 1992

By C. M. Iheagwara

An overview of the scope and ramifications of scrap recycling in the Nigerian metallurgical industries has been presented in this paper. The modern state-of-the-art processing techniques and the operational strategies employed in the recycling plants are discussed. Optimization techniques for cost effective recycling operations are highlighted. As new units within existing metallurgical plants and new metal working plants approach commercial operations, expansion of existing recycling plants and the emergence of new ones have been showing to hold the key to their profitability from the raw material standpoint. The present economic predicament of the entire industrial sub-sector, lack of sufficient foreign exchange to procure new machineries and the emergence of a maintenance culture have triggered a phenomenal increase in the number of spin-off industries which depend on metal recycling activities. This, it is argued, widens the horizon for scrap processing/recycling.

Jan 1, 1992