Search Documents

By Fourney W. L, Dick R. D

Tests were conducted in plexiglass and Rockite models to determine if crater blasting could be improved by changes in charge geometry or by alterations to the borehole. Circumferential grooves were placed at various locations in the borehole in an attempt to control the initiation site of the crater. Grooves located at or above the top of the cylindrical charge had no effect on the resulting crater. Grooves placed too low in the borehole were successful in controlling the initiation site but the growth of the fracture system was not sufficient to reach the upper surface. Grooves located at a height of two thirds of the charge length were quite successful in that resulting craters were bigger by at least a factor of six than the normal crater. Testing was conducted in Rockite models to investigate charge geometry. Spherical charges in ungrooved boreholes resulted in crater sizes that were three times larger than those caused by cylindrical charges.

Jan 1, 1990

By III Kimball

Mining wastes have received individual attention under the Resource Conservation and Recovery Act (RCRA) since its inception, in recognition of the special characteristics that distinguish mining wastes from other solid wastes. The Environmental Protection Agency (EPA) has recognized that: - Mining wastes are generated in much larger volumes than other industrial wastes. Most material handled in mining is waste (over 99% in many cases) and not marketable product, whereas waste is a small portion of raw materials used in most industries. Consequently, controls used for hazardous wastes may be technically infeasible or economically impractical. - Nearly all mining waste is managed at the site of generation and is land-disposed. . - Mining wastes typically pose lower hazards than other industrial wastes. Mining operations are located predominantly in sparsely populated areas and in arid or semi-arid areas with little surface water runoff and deeper water tables.

Jan 1, 1990

By R. E. Gundersen

Hydro-power-the use of high-pressure water as an energy source-offers tremendous benefits for environmental control in deep, hot mines. The extent of these benefits depends on the mining method, the selection of equipment to be hydro-powered, and the efficiency with which the coolth is extracted from the water and into the working environment. The engineering of hydro-power systems continues to receive much attention. However, this paper considers the environmental implications of using hydro-powered equipment, particularly with regard to positional efficiency. The integration of hydro-power with developments such as backfill, mechanization, and higher face-advance rates is discussed. Layouts are proposed that attempt to minimize the quantity of water in circulation by extracting the maximum coolth from the water.

Jan 1, 1990

A comparison of gold, platinum and sulfide ion selective electrodes was made in this investigation for determination of Eh in solutions containing sulfide ions as a model system. The comparison was made in terms of the accuracy of the measured response, response time, pH dependence, and reproducibility of measurement. In addition, the sensitivity of each electrode towards changes in sulfide ion concentration was measured in terms of the change in measured Eh per decade change in concentration of sulfide ions. On the basis of a detailed investigation of the electrode processes occurring at the surface of gold and platinum electrodes, it was postulated that within the pH range investigated these electrodes respond to changes in the hydrosulfide ion, HS-, concentration in solution. In comparison, the sulfide ion selective electrode is known to respond to changes in the sulfide ion, S-, activity in solution. Although the potentials measured with gold and platinum electrodes were mixed potentials, pretreatment procedures can be used to obtain a signal suitable for process control. For control of sulfide ions in flotation pulps, the use of a gold electrode pretreated at 1.0 V with respect to a standard hydrogen electrode is recommended.

Jan 1, 1990

Computer-based block modelling of orebodies is now used at Renison Tin mine for the estimation of ore reserves. It is considered that this has resulted in improved reserve estimation for complex 'stratafault' orebodies. The results for all orebody types are more easily understood by the mine planning section and provide greater scheduling capability than those from the previous manual isoline reserve estimation method. A structural overview of the deposit can be gained by combining geological block models for the various orebodies. It is anticipated that upon completion of block modelling for all the orebodies the time spent on the annual ore reserve estimate will be significantly reduced.

Jan 1, 1990

By Rynn J. M W, Paynter A

Recent studies by the authors have concerned themselves with assessing the earthquake risk to north-eastern Australia, based on available historical earthquake data for the area. There have been several significant earthquakes (Richter local magnitudes of the order of 6) concentrated in the Wide Bay - Burnett region in central eastern Queensland, although none of these has occurred close to a significant centre of population or development. Using derived average acceleration attenuation relations and world-wide data on earthquake-induced damage as a basis, conditions under which earthquake-induced liquefaction may occur have been investigated and presented in graphical form. Historical earthquake data for north-eastern Australia have been overlain on this graphical presentation and it has been demonstrated that the Wide Bay - Burnett region, in particular, may in the past have been on the verge of earthquake-induced liquefaction, where ground conditions are susceptible. When this is viewed in the context of the rapid growth in population and development in this area over recent years, the risk can no longer be ignored with impunity.

Jan 1, 1990

By Jeffrey L. Zelms

Environmental issues and how they are addressed -- or not addressed -- by the lead industry in the 1990s will determine the eventual fate of lead mining in both the U.S. and worldwide. Clearly, governmental regulation throughout the West will become harsher. Equally clearly, the industry has? failed to educate the public regarding lead. Instead of public support for a critical mineral, we face widespread public ignorance and paranoia. If we can demonstrate the public interest benefits of the industry, the 1990s will be a decade of continuing growth -- not dynamic growth, certainly, but growth at least comparable to the world economy. If, however, we fail to demonstrate the industry's public interest benefits, the 1990s could mark the beginning of the end of our business.

Jan 1, 1990

Ore reserve estimates form a basis for strategic mine planning at Argyle Diamonds open pit and alluvial operations. Most ore reserve statements are mainly concerned with resource tonnage and grade. Because diamond deposits are low grade, high value resources, diamond quality ($/carat) is also an important parameter. Relatively large variations in quality and/or grade can occur. These variations must be taken into account before the resource potential can be fully assessed. Computers (HP9000 and PC's) are utilised to compile resource inventories. Resource inventories are then ranked on an economic basis. This paper discusses the methods used to compile resource inventories and explains how these are then used to present ore reserve estimates in terms of resource potential.

Jan 1, 1990

By Michael F. Gleason

In 1986, Gold Fields began negotiations with a large Nevada electrical power utility to supply power for its Chimney Creek Mine In northern Nevada. After the long negotiations reached an impass over various costs associated with the power line, a decision was made by Gold Fields to generate its own power. Self-generation is not uncommon overseas, but it is rare for any but very large or very small operations in the United States. Surprisingly, under certain conditions a mine can generate its own power profitably and Gold Fields has found that the associated operating and maintenance problems are minimal. The following report details what factors went into this decision and how it works. Hopefully, it can serve as a guideline for those who may find themselves in a similar position.

Jan 1, 1990

By William Petruk

Volcanogenic base metal ores contain about 0.5 to 7 g/T Au, commonly as an intermetallic compound with Ag and/or Hg, and to a small extent • "invisible gold" in pyrite and arsenopyrite. The Au-bearing phase (electrum, Au-Ag-Hg alloy, etc.) generally occurs as fracture fillings in pyrite, arsenopyrite and chalcopyrite, and rarely • minute inclusions in pyrite and arsenopyrite. The Au-bearing phase in fractures generally occurs • small grains, and is frequently associated with galena, tetrahedrite and other late minerals. The gold is readily liberated from fractures and recovered by flotation in Ca concentrates. Copper concentrates usually recover around 60% of the gold when the ore grade is around 3 g/t. Higher recoveries are obtained for higher ore grades, and lower recoveries for lower grade ores. Lead and zinc circuits act as scavengers for gold, and recover all the exposed gold attached to small particles. Only unliberated gold, "invisible gold" and very minute gold grains attached to large particles are lost to tailings.

Jan 1, 1990

By T. D. Hackett

Multislice mining methods were analyzed by the U.S. Bureau of Mines to determine their application to western United States thick coal seams; ground control, geology, and costs were considered. Multislice mining is used in widely varying seam conditions worldwide, including flat seams too thick to mine in a single pass, pitching thick seams, and seams containing a rock parting. Longwall multislice methods predominate, but room-and-pillar variants also exist. The initial use of the method in western seams is planned at a deep Colorado mine where a rock parting will be used to separate two slices mined by longwall. Ground control and spontaneous combustion are major hazards associated with multislice mining. A well-consolidated upper slice gob can reduce ground control problems and provide a seal against spontaneous combustion. Geologic analysis indicates that the consolidation of the gob depends on the composition of the upper slice roof, the presence of water, and sufficient overburden pressure. A geologically competent intermediate rock parting can also reduce ground control problems and seal against spontaneous combustion. To compete in western coal markets, the cost of multislice mining must be within the range of normal longwall costs. Analysis indicates that multislice operating costs should be within this range, and that multislice mining costs decrease as panel width increases. Relatively wide (600 to 800 ft) panels also provide increased coal recovery.

Jan 1, 1990

By Thomas F. Mechtenberg, Michael S. Powell

In the past several years many coal operators and stone producers have reduced drilling and blasting cost by utilizing Bulk Emulsion/ANFO blends. For many operators the cost of equipment to handle blend products has been a major consideration in evaluating overall cost effectiveness of changing from packaged products or bulk ANFO to blends. This is especially true when the project length is short term or is uncertain.

Jan 1, 1990

By Zieg GA

The Sheep Creek Project lies 30 km north of White Sulphur Springs in the Little Belt Mountains of central Montana. Homestake Mining Co. discovered base metal anomalous pyrite beds downdip from gossans in 1974. Cominco American began exploration in 1976, consolidated adjacent properties, and joint ventured with BHP-Utah International in 1985. High . grade Cu and Cu/Co mineralization intersected in a 1985 drill hole led to discovery of two separate deposits. The project area now covers over 175 km2 and is being actively explored for Cu, Co and Zn in a shale hosted bedded sulphide system.Proterozoic Belt Supergroup sediments host the Sullivan Pb/Zn deposit, stratabound Ag/Cu ores of the Revett Formation at Troy and Rock Creek, and base metal rich pyrite beds at Sheep Creek.

Jan 1, 1990

By Stephen G. Hardcastle, Michel G. Grenier

"Safety and health issues are and have been in the last decade a very high priority item with all parties involved in the Canadian mining industry. As a result of this high level of concern for workers' safety and health, Canadian mines are at the leading edge of environmental control technology. For the most part, the occurrence of pollutants in mines is unavoidable. Dust from mining operations, airborne radiation, gases and heat from the strata as well as gases and particulate from diesel engine emissions will undoubtedly be found to some level in most Canadian mines. A lot of work remains to be done, however, in order to bring all Canadian mines at the same level of proficiency when it comes to safety and health. Also, more work is needed in order to maintain our status as world leaders in this field.CANMET's Mining Research Laboratories (MRL) in Elliot Lake and Bells Corners, Ontario, with the cooperation of the mining industry, have contributed to improving environmental conditions in underground and surface mining and milling operations. The extent of collaboration and efforts vary widely from long-term, multi-million dollar projects between several interested parties to smaller projects involving one laboratory and a single mining operation. This paper gives examples of such collaborative efforts and potential future directions as they apply to: mine ventilation analysis using tracer gas techniques, optimization of mine ventilation network efficiency using real-time monitoring and controlled recirculation (heat saving), respirable dust and radiation sampling and control techniques, diesel emission control using regenerative ceramic filters and, finally, the control of sulphide dust explosions and resulting sulphur dioxide production."

Jan 1, 1990

By S. P. Singh

Drifts are an integral component of underground mining. They provide access for men and material, means for transporting ore and rock and serve as air passageways. In view of their importance on the overall safety, economy and productivity of mines, empirical guidelines for controlled blasting design in drifts have been developed in this study. The application of the proposed concept was described by generating blast hole patterns for a mine with the help of a computer program. The mechanism of blast damage and the need for controlled blasting to alleviate ground control problems in underground mines have been outlined in this paper. The economic analysis between normal-and controlled blasting was performed based on the information from an operating mine. In addition, the review of drift blasting practices and problems in Canadian mines was also carried out in this study.

Jan 1, 1990

By Joseph E. Worthington

The announcement of a high-grade ore intercept near Wenatchee, Chelan County, WA, by Asamera Minerals in 1983 triggered widespread interest in this old gold mining district. The district has a long history of exploration and production and was actually one of the few underground gold mines that operated in the post World War I1 years in the US. Gold occurs in a north-trending structural zone in folded and faulted Eocene arkose intruded by andesite and dacite dikes having dates in the 42 to 50 m.y. range. Ore has been mined selectively from ladder veins perpendicular to the trend, from the south end of the trend near Squilchuck Creek. These veins narrow and silicification becomes pervasive northerly where wider zones were caved later in the operation. Recent discoveries at "B" reef at the north end are also in wide zones of silicified arkose. The gold lodes originally cropped out as prominent silicified and iron-stained ridges that were described in the early days as "reefs." The early discoveries were made in out- crop about a hundred years ago, and two claims, the Gold King and Macbeth lodes, covering the most prominent out- crops on the north side of Squilchuck Creek, were staked in 1885 and patented shortly thereafter. A five stamp mill was erected in 1894, but failed to liberate gold for amalgamation. The two patented claims were acquired in 1934 by J. Keegan, who carried out limited exploration and shipped small amounts of flux ore to Tacoma during the next few years. There was no substantial exploration or development of the claims, however, for several years after that time, and ownership of the claims eventually passed to a series of trusts administered by a bank in Seattle.

Jan 1, 1990

By Robert B. Parsons

"Effective January 1, 1990, mines in British Columbia are subject to a new provincial mining tax statute, the Mineral Tax Act. Under this Act, mines are subject to a two-tier tax system, with a minimum tax payable on ""net current proceeds"" and a higher tax paid on net income. For many mines, the present value of tax paid under the new rules should be comparable to the amount paid under the old rules. Earlier cash payments could pose difficulties, particularly for smaller mines, but existing producing mines could benefit in the short-term.IntroductionEffective January 1, 1990, British Columbia has replaced the provincial mining tax regime under the Mineral Resources Tax Act with a new system under the Mineral Tax Act. The new rules borrow some ideas from other provinces (New Brunswick's two-tier concept, and Saskatchewan's indexed costs) with a view to levying a tax that is fairer to both the producer and the province."

Jan 1, 1990

By Steve Kral

Competition in the gold mining industry throughout the world has become fierce in recent years. The challenge facing operations personnel is to produce more gold for less money. Likewise, the explorationist's charge is to find more gold in a more cost-efficient manner. That means using new technology to find new gold deposits and expand present ones. More accurate mapping instruments are available to geologists in the search for new deposits. Advanced geophysical and geochemical methods enable explo¬ration teams to review previously mined districts in their search for minable reserves. Four technical sessions on the geology, exploration, and development of gold deposits were part of the program at `world Gold '89,' a Gold Forum on Technology and Practices," held by SME and The Australasian Institute of Mining and Metallurgy in Reno, NV, Nov. 5-8, 1989.

Jan 1, 1990

By P. M. Lin

This paper presents an overall stabilization method to eliminate the potential of reoccurrence of subsidence over abandoned mine lands. The method considers column grouting at the specific locations inside the subsidence influence areas including the distressed and stress concentration zones instead of grouting' around and beneath the damaged structures. The later method is commonly used for AML subsidence abatement at the present. By using finite element method the conditions of stress distribution in the strata before and after grouting can be calculated. The design of grout pattern includes the location and number of the grouting holes. Based on the calculation, the proposed method significantly reduces the stress concentration, i.e., the potential of reoccurrence of subsidence can be reduced or eliminated. A comparative analysis including number of grouting holes, grout affected area, stress level, and potential of subsidence reoccurrence will also be presented.

Jan 1, 1990

"The Pierre Beauchemin Mine attained commercial production in January 1989, and went on to produce 23 968 ounces of gold for the year, 3% higher than forecast. Underground development was accelerated to prepare the way for the production of an estimated 40 000 ounces in 1989.IntroductionThe Pierre Beauchemin Mine is located nine miles west of the city of Rouyn-Noranda (Fig. I).As a result of the amalgamation with Sullivan Mines in October 1987, the mine is now entirely owned by Cambior Inc.The Eldrich deposit was discovered in 1953and began production in 1955, closing in 1962 following the decrease in gold prices and the simultaneous decrease in silica content in the ore, which was sold to the Noranda smelter for flux. A total of 717 000 tons grading 0.14 oz Au/t were produced during this period.From July 1984 to October 1987, an underground exploration program was carried out by Sullivan on the Eldrich mining concession and the nearby Flavel property. The first phase of the program included reinstallation of surface facilities and dewatering of the Eldrich Mine. Following the completion of the first phase, extensive exploration was carried out, including a major program of diamond drilling. It was then decided to deepen the shaft to a depth of 1800 ft to access a new zone called the No.5 Zone .Following the amalgamation with Sullivan in October 1987, Cambior assumed the role of operator for the project, and continued the shaft deepening work that had already been started. A feasibility study was completed in April 1988 and the Cambior board of directors approved a production decision for the Eldrich-Flavel project.The preproduction program extended from May to December 1988 and was aimed at preparing the stopes in the upper part of the mine and at developing the mine infrastructure at the bottom of the mine.The mine was officially opened in August 1988. Cambior renamed the project the Pierre Beauchemin Mine in recognition of Pierre Beauchemin's pioneer-work."

Jan 1, 1990