Search Documents

By G. Wonnacott

A model for simulation of gravity regrinding circuits is presented. The model can predict "secondary" density distribution data from a series of "primary" grind/density distribution tests. Thus middlings regrind requirements can be predicted from primary grind data. Traditional methods of regrind design involve lengthy and tedious tests programmes. The model presented herein can considerably reduce the quantity of testwork required for regrind design. The model can also be used to design primary gravity grinding circuits. A parameter estimation scheme and experimental data validating the model are presented.

Jan 1, 1989

By E. Chin

Natural gas was Bangladesh's only significant exploited mineral. A few other minerals or mineral-based commodities were produced for local consumption. The most valuable were nitrogen fertilizer, salt, cement, and clay for brick.2 The most important mineral industry development of 1987 was the start of modest production of crude oil, the first discovered and produced in the country. PRODUCTION AND TIADE Production of natural gas from the nation's huge reserves continued to increase but was limited by the lack of residential and industrial demand. Gas reserves of 7 trillion to 16 trillion cubic feet were sufficient for far more production than the country could efficiently utilize for many years. The country's consumption-to-reserves ratio was one of the lowest of the developing nations. Mineral exports have been insignificant, comprising a small amount of nitrogen fertilizer. Nitrogenous fertilizer exports could become important when planned new capacity comes on-stream. Mineral imports were dominated by crude petroleum.

Jan 1, 1989

By D. H. H. Quon

Results of a study conducted to determine the properties of iron ore pellets made from Mount Wright and Carol Lake ore concentrate fines with partial and full substitution of bentonite by several organic binders are presented. Carboxy methyl celluloses 7H and 6TL, hydroxy ethyl cellulose (natrosol) and modified guar gum all produce pellets of acceptable wet, green and dry strength. However, when fully substituted, an inorganic binder such as calcium carbonate is required for satisfactory strength development after induration. Mixing the Carol Lake ore with Mount Wright ore in a 50-50 ratio also achieves the same result. The failure of the Carol Lake ore in the pelletization process is attributed to the low hematite content of the ore. The results are very similar to those from the extrusion studies reported earlier (8).

Jan 1, 1989

By P. Somasundaran, Brij M. Moudgil

All the major interfacial technologies encountered in mineral processing involve adsorption of surfactants and/or polymers. With the need for processing low grade complex ores it is imperative that conventional techniques such as flotation and flocculation be extended to meet the challenge of treatment of fines. Addition of surfactants or polymers is indeed not limited to the solid-solid separations but extends to particle size reduction in the form of grinding aids and dewatering operations as well. Although progress has been made in recent years to understand the science involved in various interfacial processes, more challenges and opportunities exist today than ever before in processing of the low grade finely disseminated ores. A brief review of the recent advances and the challenges in mineral processing, especially, those related to the interfacial technologies is presented.

Jan 1, 1989

By David M. Mchaina, Allan E. Hall, Siegfried Rohr, J. D. Botsford

Incidents associated with secondary dust ignitions in the mining of massive sulphide ore deposits are of major concern in Canadian underground metal mines. During stope or development blasting, a highly concentrated cloud of sulfide dust is created and may be ignited, resulting a secondary explosion which releases a considerable volume of sulphur dioxide and possibly other sulphur gases. The consequent pressure, heat and toxic gases can result in loss of life, significant damage to equipment and loss of production. These losses are expensive and should be prevented. Explosions of this type have occurred at the H-W mine of Westmin Resources mainly in the development headings and cut and fill stapes. This paper presents the results of a study conducted at the H-W mine to compare dust sampling methods for explosivity tests. The associated benefits and pitfalls of each sampling technique are examined. The investigative work conducted to develop and test preventive and control methods against sulphide dust ignitions is also discussed. The techniques which will minimize the risk of sulphide dust ignition in metalliferous mines are outlined. A review of current preventive and control measures practised at the H-W mine is also presented.

Jan 1, 1989

By I. J. Barker, D. A. Vetter, G. A. Turner

The modeling of the uranium-leaching process, and the logging of data from a plant for the evaluation of the model, are reported. A phenomenological approach was adopted in the development of the model. A set of eight chemical reactions was chosen to represent the complex chemistry of the process, and kinetic expressions for these reactions were incorporated in differential equations representing mass and energy balances. These equations were coded in FORTRAN to form a program that simulated the process, and that allowed averaged and continuous data from the plant to be compared with the model. This allowed the model to be 'tuned', and to reveal a number of minor

Jan 1, 1989

By Kalliat T. Valsaraj, Louis J. Thibodeaux

A mathematical model is described for the transfer of hydrophobic compounds from aqueous to an immiscible organic phase using fine bubble aeration; the process otherwise known as "solvent sublation" an adsorptive bubble separation process. The limitations of the model are explored by simulating experimental results both for a batch scale process and a continuous process. The qualitative predictions of the model with respect to the influence of the organic layer (mineral oil) are tested by performing experiments using chloroform and 2,3,6-trichloroanisole as hydrophobic compounds in the aqueous phase. The continuous process is seen to be limited by the requirements of fine bubble generation and the ratio of influent feed rate to air flow rate.

Jan 1, 1989

By Tilley J. L, Chicu D

The development of the Yallourn East Field brown coal open cut has involved the adoption of novel investigational programs into coal qual- ity. For example, weighted average coal property statistics for key proper- ties are determined by using a unique blend of traditional and 3-dimensional geostatistical estimation. Predicted property values are made freely available from the mainframe computer in the form of kriged esti- mates of 60 000 tonne coal blocks. Geostatistical predictions are being incorporated within the Mincom/Intergraph CADD system which is used for mine design. Key properties relating to coal type, moisture, and ash have been evalu- ated to provide the required data for the design and operation of both the open cut and the power stations as well as the briquette plant.

Jan 1, 1989

By Aalbers J. P A

The State Electricity Commission of Victoria (SECV) operates 13 excavators, 3 travelling stackers and 4 mobile slew conveyors in their three open cuts in the Latrobe Valley. The majority of these machines have been designed and constructed to a German design code current at the date of order. The SECV has always ensured that the machines were manufactured and erected to the appropriate standards. The SECV has a policy of having all machines inspected by an independent inspector every two years. These inspections are based on those carried out in Germany. The inspections have been carried out by inspectors from Germany who have the necessary experience to do similar work in German open cuts. Major faults found during the inspections have been repaired, however,the gradual breakdown of corrosion protection system has continued. The structures on some machines have areas of bad corrosion. This, coupled with wear on major mechanical equipment, would require an extensive outage to overhaul the machines. Refurbishment of Hazelwood Power Station will result in higher levels of production and extended life for the station. This will require improvement in the total output from Morwell Open Cut (MOC). To meet this increased coal demand, the open cut equipment will need to operate more efficiently and for a longer period of life.

Jan 1, 1989

By O. A. Bascur

The problem of setting the proper control objectives and/or having several objectives to be met in the implementation of grinding control strategies can be resolved. The design and implementation of a distributed control system for safe operation of a grinding circuit while maximizing profit is presented. An optimal recovery/throughput target for a desired grind is accomplished by advanced control strategies at the DCS level. A mill load constraint control technique provides stable operation with a substantial increase in throughput, while the desired grind index is maintained by an inferential grind control technique without using a particle size analyzer. The integration of crushing/grinding and flotation in the overall design was the key to the success of the project. This synergistic effect was obtained by implementing a computer -plant management system in the concentrator. The overall philosophy of keeping the implementation simple but not simpler was used.

Jan 1, 1989

By Warner N. A

There is an inherent problem in producing simultaneously lead, zinc and copper as metals in a single polymetallic smelting furnace. It relates to the condensation of lead and zinc from the gas phase under vacuum conditions such that metals in bulk form, either solid or liquid, are obtained as products rather than a fume or dust containing both metallic and non-metallic components. To understand this phenomenon, it has been necessary to establish mathematical models with computer simulation to identify the process requirements for effecting the objective of maximum bulk metal production with minimum fog formation. The theoretical framework of simultaneous heat and mass transfer involved in condensation from gas mixtures containing a non-condensable gas has been extended to the high temperature and reduced pressure conditions. These apply to new technology for polymetallic smelting now being developed in a project currently funded jointly by the Commission of the European Communities and the Mineral Industry Research Organisation. Under the right conditions it is theoretically possible to condense out both lead and zinc with minimal fume formation, but in all practical cases it is anticipated that some circulating load for reversion back to the smelter will be needed.

Jan 1, 1989

By Duane A. Smith

Horace Tabor. No 19th century Colorado mining man is better known but, unfortunately, probably less understood. He is little appreciated for his significant contributions to the industry and the state. A century ago, Tabor was headline news. The legend today, however, has become so all pervasive and so interwoven with fact that the two are hard to separate. For example, he never told Baby Doe on his death bed to hang on to the Matchless mine. Yet this has emerged as staple Tabor fare. So much attention has been focused on his matrimonial triangle that it overshadows the man. Symbol of mining's reward Tabor traveled west in the 1859 Pike's Peak gold rush. In the next generation, he came to symbolize the rewards mining might lavish on an individual. The Leadville Daily Herald (Sept. 10, 1882) could write, without exaggeration, that "the extent which the mining industry of Colorado is under obligation to Tabor cannot be easily estimated - what he has done for Leadville and Denver is patent to all." It had not come easily, nor had Tabor started out a success. His early placer mining at Payne's Bar, near present-day Idaho Springs, CO, had turned no fortune. So in 1860, he, his wife Augusta, and son went south to Colorado City, then over Ute Pass and up the Arkansas Valley to Oro City. Arriving soon after the initial discovery, Tabor staked a good claim. With a sharp eye, he and Augusta broadened their base by establishing a store. Both mining and business would pay dividends in the following years. By the season's end, though, Oro City was already declining. Always on the lookout for a richer district, Tabor and his family moved the next year across the mountains to promising Buckskin Joe. The familiar pattern followed, with the store and post office being the center of their attention. Mining investment and management now replaced the earlier physical panning and sluice operating. Seven years later, the Tabors abandoned Buckskin Joe and returned to Oro City. It had moved up California Gulch to be near the district's best mine, the Printer Boy. Middle class was not enough Middle class respectability, plus a steady income, was the Tabor's by the 1870s; fine as far as it went. But it proved far from the fortune Horace had always been seeking. Oro City languished in the backwash of Colorado mining and Tabor seemed like many men who had drifted around the Territory following the ebb and flow of mining. His faithful wife Augusta had been a steady factor in the success the family achieved. She helped year after year to operate the store and post office. Not simply the happy-go-lucky individual he has often been portrayed, Tabor was a hard working businessman/mine owner. An R. G. Dun and Company agent evaluated him in 1876 "Net worth $23,200. Is a very shrewd businessman and not liable to lose money, has a good chance to make money as he had no competition." Leadville: Tabor's silverlined-fortune After all those years on the Colorado mining frontier, in 1877, Lake County's wealthiest and most respected merchant made another move. It was short in distance, only 4 km (2.5 miles) down California Gulch, then a little north to a new mining camp. This new camp, soon named Leadville, gave birth to the Tabor fortune and legend. Middle-aged (Horace was 47), the Tabors once more set up their general store and found themselves in the midst of the open¬ing of a new district. This time silver beckoned and not the gold that had brought them West 18 years before.

Jan 1, 1989

By M. K. Gangal, E. D. Dainty

The paper describes the use of portable aerosol monitors in determining real-time concentrations of diesel soot and respirable total dust in dieselized mines. The field studies were conducted in a simulated diesel environment in the laboratory where no other type of dust was present, and in four underground mines with multi-diesel machine operations. Two packages for the real-time monitoring of diesel soot were prepared which included two types of aerosol monitors: a Miniram, model PDM-3, and a Sibata, model PDS-1. These monitors utilize the principle of light-scattering to measure the airborne mass concentration in the environment. The monitoring device results were compared against the Time-Weighted-Average (TWA) values produced by the gravimetric filter sampling method, permitting calibration factors to be determined for each field test. Both instrument packages provided comparable results. The instrument calibration factors varied for different tests, which may be due to different material composition, particle size distribution, density and shape of the aerosols. This approach for real-time determination of diesel soot is found to be simple, inexpensive and easy to use. More field tests for diesel soot determination and further research on size distribution of particulates in dieselized mines are required.

Jan 1, 1989

This work shall consist of furnishing and driving foundation piles of the type and dimensions designated on the plans or in the special provisions including cutting off or building up foundation piles when required. This specification also covers providing test piles and performing loading tests. Piling shall conform to and be installed in accordance with these specifications, and at the location, and to the elevation, penetration and bearing capacity shown on the plans or as directed by the Engineer. Except when test piles are required, the Contractor shall furnish the piles in accordance with the dimensions shown on the plans or special provisions. When test piles are required, the pile lengths shown on the plans are for estimating purposes only and the actual lengths to be furnished for production piles will be determined by the Engineer after the test piles have been driven. The lengths given in the Engineer's order list will include only the lengths anticipated for use in the completed structure. The Contractor shall, with-out added compensation, increase the lengths shown or ordered to provide for fresh heading and for such additional length as may be necessary to suit his method of operation.

Jan 1, 1989

By V. Srajer

Several optimization approaches used by the Canadian mining industry were used to investigate surface coal mining operations in Canada. A computer program was applied to optimize truck/shovel systems and for various analyses. The analyses of eight western Canadian coal mines included investigation of fleet imbalance, under- and over trucking, development of the criteria for automated truck control, comparison study of various haulers and loaders, haulage layout, driving conditions, machine performance, servicing and maintenance policies, etc. Each property investigated supplied background information for the study and cooperated in optimization studies. The truck/shovel system optimization study is demonstrated as a test case to outline procedures and step-by-step instruction for similar applications.

Jan 1, 1989

By Jerry R. McGaha, Joseph A. Dos Santos

The favorable economics of conveyor based haulage, especially in moving large volumes. has long been acknowledged. This has given impetus to significant developments over the last two decades in conveying systems and equipment. Such developments have resulted in improved equipment and system reliability, versatility and mobility. The present writing presents conveyor systems and their variations. Long overland conveyors of various profile and plan layout are considered along with various typical support systems. This includes discussion of horizontally curving, two-way and booster driven conveyors. High Angle Conveyors-[HACs] are reviewed, citing in-pit as well as plant application. Finally, several important advances in idler and in pulley design are presented.

Jan 1, 1989

By E. Henderson

"This paper outlines the upgrading of a double-drum 2000 hp cage hoist to provide fully-automatic operation from shaft station control panels. The application utilizes programmable controller technology to provide all necessary functions for movement of personnel and material to 22 locations in a 4000 ft shaft.Various functions involving special design considerations such as ""chairing"", ""jogging"", and three modes of ""multi-level calling service"", are outlined. The use of higher level PLC functions to optimize memory utilization and simulate ""elevator service"" required the addition of a comprehensive fault finding software section to aid in troubleshooting.This paper will deal primarily with the automation portion of the project with references made to other pertinent aspects which were prerequisite to automatic operation. It is not intended to deal with every design detail, but rather to provide an overview of what can be done in the area of automation for those considering such an application. INTRODUCTIONEarly hoisting control systems provided only the essential elements of control, leaving many responsibilities with the operator. With advancements in various areas of technology, electromechanical devices were incorporated to enforce slow-down in end zones, control acceleration rates, monitor safety devices, etc. Brake control systems were supplied to allow for ""single-stick"" operator control, regulated deceleration during emergency brake applications, etc.These additions enhanced the over-all performance but were generally confined to speed and current regulation. Some mechanical devices, such as travelling nut limits, etc.; were used to provide ""position"" control to multiple locations within the shaft. These devices, in conjunction with rather extensive relay control panels, did allow for the establislunent of some automatic cage hoists . The hoists were often limited to service from point ""A"" to point ""B""', involving a limited number of levels due to the complexities of the mechanical interfaces employed. Only limited systematic work sequences were possible . .Programmable Logic Controllers (PLCs) were introduced into industry in the mid-70s and have since gained acceptance in mining applications such as pumping, ventilation, ore handling, etc. This technology, being ""software"" based, allows complexities to reside in the program rather than increasing the number of physical control elements. This has opened the door into hoisting systems for automatic loading and hoisting of ore as well as a means to achieve a comprehensive package of automated cage hoisting functions."

Jan 1, 1989

"Mineral flotation processes are often characterized by long dead times and slow process dynamics. The process dynamics change due to different ore types, feed grades and circulating loads. These are some of the factors that can make control of flotation processes difficult. Implementation of adaptive control algorithms at Brunswick Mining has made controlling these processes feasible. The role of adaptive controllers in plant optimization and the overall control philosophy is discussed.IntroductionBrunswick Mining is located just outside of Bathurst, New Brunswick, Canada. The concentrator processes approximately 10,250 tonnes per day of ore that assays at approximately 8.9 %Zn, 3.6 %Pb, 0.3 %Cu and 100 gram/tonne of Ag. The four products produced are zinc concentrate assaying 51 %Zn, lead concentrate assaying 36 %Pb, copper concentrate assaying 21 %Cu, and a bulk concentrate assaying 32 %Zn and 18 %Pb.The original flotation process control system, supplied by Outokompu Oy of Finland, was replaced in the summer of 1988 by a Provox system supplied by Fisher Controls Inc. The Provox system consists of two redundant integrated function controllers (IFC's), two operator console stations with two screens each and a Digital Equipment Co. microVax II computer running Fisher's Computer Highway Interface Package (CHIP).In January 1989 a boiler management package, which includes the boiler control hardware and another operator's console, will be added to the Provox system. In late spring of 1989, a Vax 3200 computer running G2 artificial intelligence software from Gensym Corporation will be installed. These devices are all connected using a redundant data highway that runs around the plant.The primary measurement devices in the flotation circuit are two Courier on-stream X-ray analyzers. The Courier systems each have 14 sample cells with two streams multiplexed into each cell. Each pass of the on-stream head takes approximately 6 minutes yielding a nominal sampling interval of 12 minutes. The Courier passes its assays to its respective IFC. The IFC handles the digital and analog I/O, DDC and cascade loop control, some low level calculations and sequencing. The CHIP microVax has 9MB of memory and 220MB of mass storage running under the VMS operating system. The CHIP microVax is a central database for the Provox system. It is used for data trending, metallurgical modelling and balancing, instrumentation database, long term storage, and on-line adaptive assay control."

Jan 1, 1989

This brief overview of the history of Brown Coal mining in Victoria is a luncheon presentation -I do not intend to make it indigestible with extensive listings of resources or production. There is a vast pantry of collated historical records and of vari- ous predictive studies available for the enquired with a hearty digestion. A gourmet collation is provided in The Aus IMM Monograph No 11 published in 1984 entitled "Victoria's Brown Coal-A HUGE FORTUNE IN CHANCERY", currently still on offer by the Institute and available at a bargain price in the foyer at this conference. Monograph No 11 also provides a feast of excellent references on the theme of Victorian Brown Coal assembled by the several contributors. In contrast, my presentation paper is a fast-food service, extracts from the printed paper only-you have no choice-you "get what you get" and in small quantity. I hope it will tantalise your appetite -like Oliver Twist you will ask for more. -Buy the Monograph!

Jan 1, 1989

By A. K. Ratte, C. M. Brown

"IntroductionIn autogenous mills, grinding of the ore feed is accomplished by the direct action of the variously sized rocks making up the feed on each other and the mill interior. Size reduction is achieved without the addition of grinding media foreign to the mill feed, differing in this respect from rod, ball, and pebble milling. The term ""semi-autogenous"" has entered common usage in the industry to describe autogenous mills to which supplementary grinding ball additions are made to increase the rate at which size reduction of the mill feed occurs, beyond that achieved solely by the action of rock on rock. In a semi-autogenous grinding (SAG) mill, 50Jo to 10% of the mill volume may be occupied by grinding balls, whereas a range of 25% to 45% is more usual in ball milling.The comminution of mineral ores using ""conventional"" techniques has been described in previous papers. In conventional operations, size reduction of mined ore, and liberation of the valuable mineral content, is typically accomplished using flowsheets employing two to four stages of crushing. Crushing is followed by one to three stages of grinding and classification using various combinations of rod, ball, and pebble mills. This paper describes operations employing autogenous or semiautogenous grinding as the principal stage in the comminution process. Primary crusher discharge, or in some instances run of mine ore, is fed directly to an autogenous or semi-autogenous grinding circuit. Final product sizing may be accomplished in a single grinding stage, the mills operating in closed circuit with classification equipment, or in several stages using autogenous and semi-autogenous mills for primary grinding, and ball or pebble mills for secondary grinding. In several operations a portion of the primary mill discharge is crushed in an intermediate comminution step, these circuits being called autogenousball- crusher circuits (ABC). Many different flowsheets exist, but common and important to most are crushed ore stockpiles, reclaim feeder and mill feed conveyor systems, pumps, screens, and classifiers. Autogenous grinding is employed in both wet and dry processes, although today wet predominate."

Jan 1, 1989