Search Documents

By Clifford J. Roblee

In this paper, various seismic indicators are evaluated for ability to discern fractures induced into a rock mass by blasting. This is accomplished by presenting results from in situ crosshole seismic studies performed prior to and after a sequence of controlled blasts within limestone and dolomite rock near Austin, TX. Indicators investigated are compression (P-) and shear (S-) wave travel times, first peak and maximum amplitudes, first arrival rise rate, and the linear spectrum of the received signal. Compression wave travel time yielded the most consistent results, while the various amplitude indicators yielded the poorest results for the equipment configuration utilized. In addition, this study documents magnitudes of change in seismic measurements which occurred following blasting. Both P- and S-wave travel times exhibited a wide range of variation due to blasting. Near blast centers below the surficial fractured rock, velocity decreases of about 10% were noted, significantly less than the 50% decrease observed for previously fractured near-surface rock through which the explosive energy was vented. Signal amplitude measurements also varied in magnitude but were less consistent.

Jan 1, 1989

By J. D. Morgan

The US economy continued to grow steadily in 1988, reaching an annual rate of $5 trillion in the last quarter (US trillion = 1012). The value of domestically processed mineral-based materi¬als rose 20% to $300 billion (US billion 109). The value of metals produced from US ores rose 40% to more than $10 billion, industrial minerals rose 6%' to $20 billion, and recycled scrap more than doubled to $10 billion. Increasing economic activity stimulated metal prices. Yearly lows and highs were 95 cents and $1.68 for copper, 52 cents, and $1.30 for aluminum, 34 cents and 42 cents for lead, and 43 cents and 75 cents for zinc. A number of mining and metal companies experienced significantly increased profitability. Consumer demand strongly affects mining because the US economy is relatively saturated with long-lived products. Consumer, mortgage, and Federal debt continued to rise. About 246 million US citizens already possess 170 million licensed motor vehicles and 100 million dwelling units. New car production remained at the 1987 level of 7.1 million units. Truck and bus production, however, rose 7% to 4.1 million units. New housing starts fell 7% to 1.5 million units. Imports supplied a significant proportion of total US consumption of several important mineral materials. By year-end, imports of crude and refined petroleum exceeded domestic crude oil production. Such imports cost $42 billion. Imports of nonfuel mineral-based materials were valued at $44 billion and exports at $35 billion. The US and Canada-the world's two largest trading partners-consummated a historic free trade agreement. In February, President Reagan transferred responsibility for stockpiling strategic and critical materials to the Secretary of Defense. And, in July, the GSA group that bought, stored, rotated, and sold stockpiled materials was transferred to the Defense Department's Defense Logistics Agency. Concern about apartheid in South Africa continued, resulting in increasing attention to chromium, manganese, platinum-group metals, cobalt, vanadium, and gold. The Defense Production Act, authorizing priorities and allocations, supply expansions, voluntary agreements, and the National Defense Executive Reserve, was amended to include provisions for averting harm to national security from foreign takeovers. The DPAct, in effect through September 1989, is now up for further extension. Under the Act, the US Bureau of Mines maintains the Emergency Minerals Administration. During the year, consultations were held with Canada to strengthen the North American Defense Industrial Base. Coal production, 60% from open pits, rose 5% to 870 Mt (960 million st). Nearly four-fifths was burned to generate 57% of US electricity. Exports included 56 Mt (62 million st) of metallur- gical coal and 29 Mt (32 million st) of steam coal, with a total value of $4 billion. Domestic petroleum produc¬tion fell 2% to 574 hm3 (3.6 billion bbl). Uranium mining, including recovery from phosphates, was unchanged at 5.9 kt (6500 st). Nonfuel minerals Major metals Raw steel production-a major con¬sumer of many minerals-rose 14% to 92 Mt (102 million st). Domestic iron ore production rose 25% to 59 Mt (65 million st), about 96% pelletized. Net imports rose 37% to 16 Mt (18 million st). Raw steelmaking capacity of 102 Mt (112 million st) was unchanged. Voluntary Restraint Agreements with 21 steel exporting nations limited im¬port penetration to about 20% of the domestic market. Domestic producers of bulk ferroal¬loys of chromium, manganese, and sili¬con operated at about 75% of capacity. The US mined no manganese or chro-

Jan 1, 1989

By Hsing Kuang Lin

Ferric chloride leaching w.as applied to a complex sulfide ore from Tok, Alaska to dissolve zinc, lead, silver and copper. Gold in the leaching residue, as well as in the ore, is found to be refractory to the conventional cyanidation process. Roasting, pressure oxidation and elemental sulfur removal followed by cyanidation were tested to improve gold dissolution. Also tested were thiourea leaching and high-pressure cyanidation. The readsorption of dissolved gold by carbonaceous matter in the chloride leaching residue was analyzed. Based on the experimental results, factors causing difficulty of gold dissolution from the leaching residue are discussed.

Jan 1, 1989

By B. M. Davis

The Colosseum Mine is within the Clark Mountain mining district located approximately 72 km (42 miles) southwest of Las Vegas. Nevada in San Bernardino County, California. Gold mineralization at the Colosseum Mine is hosted in two 150 m by 210 m (500 ft X 700 ft) interconnected. rhyolitic intrusive breccia pipes that intruded Precambrian crystalline basement rocks and over-lying Paleozoic marine sedimentary rocks. Sub-sequent erosion (de-roofing) of all of the Paleozoic section and a portion of the Precambrian section has exposed the pipes to the present level (probably a significant depth in the original breccia pipe system).

Jan 1, 1989

By M. F. Chambers

Neodymium metal was electrowon from a molten-chloride electrolyte at 650° C using a molten-metal cathode. A 50 mol pct NdC13-50 mol pct KC1 mixture served as the electrolyte. Binary metal alloys of 'Mg with Zn and Mg with Cd were used as molten cathodes. Under the best conditions, current efficiencies were 90 pct with a Mg-Zn cathode and 80 pct with a Mg-Cd cathode. Vacuum distillation was performed at 1,100° C for 30 min under a vacuum of 10-3 to separate the cathode metals from the neodymium. Neodymium metal of 99.9+ pct purity was recovered from the Mg-Cd alloy cathode. Almost 2 pct zinc remained in the neodymium recovered from the Mg-Zn alloy.

Jan 1, 1989

By C. D. Litton

This paper describes two new gas diagnostic techniques which have been used successfully to determine: 1) the combustion status of underground mines which have been sealed due to fire (Littol1 Ratio); and 2) the location of fires in abandoned, underground mines or waste banks (Kim Ratio). The Litton Ratio makes use of the rate of change of CO, calculated on both an air-free and methane-free basis, from mine gas samples and compares these values with those expected from a normal, combustion-free environment. The Kim Ratio uses the concentrations of total hydrocarbons, C2 ?C5, less the methane, to arrive at ratio values which increase as combustion intensity increases. The details of these two new techniques, their application to real situations, and their limitations will be discussed.

Jan 1, 1989

By E. J. Marcotte

"IntroductionDevelopments in the preparation, hydraulic transportation and placement of classified mill tailing as an effective backfill and support for mining excavations, have made feasible several advancements in mining methods that are safer and more economical. Hydraulic backfill systems have played an integral part in the development of more efficient cut-and-fill and blasthole stoping.The hydraulic transportation of tailing fill has made possible the elimination of expensive and laborious transportation, placement and spreading of gravel type fills. Also, in cut-andfill stopes, the use of hydraulically placed consolidated fill has largely eliminated the need to use extensive timbering for floors and supports, previously necessary when only gravel type, waste rock or unconsolidated tailing fill was used .Another important advantage of using mill tailing as backfill is that it decreases the need to contain a large portion of the mill solids waste in a surface disposal area and thus reduces environmental and ecological problems.Tailing Fill PropertiesConsolidated tailing fill consists of deslimed mill tailing and Portland cement. These two materials are mixed together in various proportions to form a high density slurry which is transferred underground by gravity through boreholes and pipelines. After placement underground, the water is drained off and the mixture is allowed to set. The strength of the consolidated fill is dependent on the cement content, particle size distribution and curing time. A typical tailing/ cement ratio used for bulk filling in stopes requiring vertical wall support is 30:1. Ratios ranging from 8:1 to 5: 1 are used for stope floors. High pulp densities minimize segregation and loss of cement during placement as well as reduce the amount of drainage water to be handled."

Jan 1, 1989

By James S. Hanson

Existing models proposed for the bacterial leaching of metal sulfides generally fail to predict solubilization rates at times greater than a few tens of hours. The reasons for this may be that these models are empirically based and use first order bacterial and chemical oxidation rates. This type of model is satisfactory for short time predictions (on the order of 20 hours) when the bacterially catalyzed dissolution is relatively minor. However, when bacterial action becomes more pronounced, these models consistently predict higher dissolution rates than those commonly observed in laboratory experiments. The present model uses several fundamental chemically and biologically based assumptions to predict the dissolution rate of a chalcopyrite concentrate for extended leach times up to the precipitation of jarosite. The main assumptions made are that Monod growth kinetics prevail, T. ferrooxidans adsorb onto the surface of the mineral (not necessarily mineral specific), and that during periods of high growth oxygen transport may become rate limiting. The model also relies on the energy efficiency of the bacteria in fixing carbon (growth yield) and correlates this value with available surface area of the mineral particles and the bacterial growth rate.

Jan 1, 1989

By Robert F. Chaiken

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned coal fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,000° C (1,832° F), and could be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the. 1900's and was surface mined in the 1940's. In the winter of 1961~62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated but, not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report, although considered part 2, is actually the last of a five-part series that describes the Calamity Hollow Mine Fire Project. It was written last because it involved the analysis of a substantial body of data describing in detail the results of a continuous 4-month burnout operation. The first report, part 1, describes the design and construction of the field installation. Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 deal with the closeout phase of the field demonstration. Part 4 describes the procedure used to quench the fire, and part 5 describes the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration, which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is suffIcient for energy utilization, and (3) water injection-fume exhaustion is a potentially effective method for cooling large underground fire zones. Further investigations of both Burnout Control and the water injection-fume exhaustion quenching procedure are planned.

Jan 1, 1989

By Jeffrey M. Listak

This report describes a study, conducted jointly by BethEnergy Mines Inc. and the Bureau of Mines, to assess the effects of longwall front abutment loading on various supplemental support materials utilized in a predriven recovery room. The purpose of the predriven recovery room is to reduce longwall equipment transfer time by eliminating the premove preparation associated with conventional recovery methods. In addition, the room provides a large area in which face salvage equipment can maneuver. Results of four recovery-room study areas show the progression and influence of the front abutment on the longwall panel and supports and their subsequent behavior. The best performance (i. e. the support that most facilitated recovery) of support material was achieved through the use of a concrete mixture which had a sand content of 35 percent by volume. The longwall transfer time was reduced by 30 percent which translates to a production advantage of 37,000 raw tons of coal per panel.

Jan 1, 1989

By J. W. Jang

The wear behaviors of grinding media with different chemical compositions and microstructures in wet grinding of a quartz-pyrrhotite mixture was investigated under various environments. The marked ball wear tests showed that the wear rate could be minimized by a suitable combination of martensite and ferrite within the same ball. A ball composed solely of hard martensite exhibited increased wear under an oxygen environment, while balls composed of both soft ferrite together with hard martensite exhibited decreased wear due presumably to the difference in their passivation? behaviors. The galvanic interactions between the two phases as well as among these phases and an electroactive mineral were investigated through electrochemical measurements under abrasive conditions in a slurry. The rates of formation of passive films controlled the corrosion currents of the high chromium steel media. Corrosive wear and its effect on flotation are discussed using the passivation kinetics model thereby developed.

Jan 1, 1989

By Robert Dimock

The successful management of large dispersed mineral operations is dependent upon accurate and timely decision making. The plant locations providing the data to support the decision making process are generally separated by distances which elongate the time required to accumulate the data at a central focus. The need exists to examine operational data in context with total mining operations, and in relation to target projections and historical trends. The use of microcomputers for local information tasks is an established capability. Grouping microcomputers into local-area networks is rapidly becoming established. Interconnecting multiple local-area networks to provide a free flowing stream of information between all operational locations of a mining enterprise is possible with use of some emerging technologies. The benefit of the potential interconnections and rapid transfer of information can readily be seen from a production reporting perspective. Numerous other advantages exist' by providing routing to enable a workgroup to be established between separated work functions.

Jan 1, 1989

By W. J. Grose

The Embankment Place office development over the platforms of Charing Cross Railway Station in London has presented many interesting and unusual problems to the engineers involved with the project. The main structure is supported on widely-spaced columns which penetrate the station platforms and underlying vaults, calling for high capacity foundations built in severely restricted spaces. Hand-dug underreamed piles were chosen. Whilst a conventional design approach was taken to size the piles, a detailed appraisal of ground movements was made to explore the effects of the new building loads on the existing foundations, not only beyond the site perimeter but also those amongst the new foundations. Before construction of the pile proper could take place, it was necessary to sink a caisson through the upper unstable and water-bearing soils. This being identified as a high-risk item, a full-scale trial was carried out prior to embarking on the main works. The twenty-one hand-dug piles were 2.5m diameter, over 30m deep and belled out to between 4.5m and 6.6m.

Jan 1, 1989

By W. R. Hopkins

Over 95 percent of the world's refined copper is now produced by electrolytic processes. The bulk of this electrolytic copper comes via the conventional route for sulfide ores of concentration, smelting and electro-refining. A rapidly increasing percentage of world production is now achieved using hydrometallurgical routes involving dissolution of the copper values from minerals, purification of the resultant leach solution by solvent extraction and finally deposition as cathodes by electrowinning. The technology can now be considered mature and this paper endeavors to summarize recent developments which, from the authors' perspectives, are important.

Jan 1, 1989

By Stephen D. Smith

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing. the stage of measurement used in this chapter is what is normally termed ?mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1989

SABS quality mark for explosives* AECI Explosives and Chemicals Limited has been awarded the SABS permit to apply the SABS standardization mark to al its permitted NO explosives manufactured at Modderfontein.

Jan 1, 1989

By C. J. Pritchard

As productivity improvements reduced the number of continuous miner sections from seven to three while maintaining full productive capacity, a decision was made to test an advancing tailgate ventilation system on the shortwall mining section. Having the shortwall mine its own return air system has freed the third mining section for more productive, less costly mining. The advancing tailgate has provided effective ventilation across the face and gob with acceptable pressure losses. The tailgate development continuous miner section has been since transformed from a low productivity part-time function to a high productivity development/retreat panel and is available for long term mine development duties also.

Jan 1, 1989

By R. A. Paul

WIDCO, operator of the Centralia Coal Hine, chose dredging, a method not commonly used for overburden removal, as the fastest, safest, and most economical method for mining through an alluvial filled valley. Now that the work has been completed, how did the cost and schedule compare with the original estimates? What would we do different next time in preparing for a dredging contractor? What are the potential pitfalls working with a dredging contractor? Would we do it again? When should dredging be considered as an overburden removal option?

Jan 1, 1989

By C. J. A. Davie

"SUMMARY A practical application of nitric acid oxidation of sulphides, based on the principles of the Arseno process, has been developed for the Cinola ore. Development of the process has been based on testwork conducted by Bacon Donaldson of Vancouver and Hazen Research of Denver, and on conceptual engineering performed by Minproc Engineers of Denver.A comprehensive Stage II report for the project has been submitted to the B.C. permitting agencies, containing provisions for a zero discharge tailings impoundment system and prevention of acid mine drainage. Approval in principle is expected in early 1989.A feasibility study recently completed by Minproc Engineers and Davy McKee Corporation demonstrates that this project can be brought to production for a capital expenditure of C$120 million for a mill throughput of 6,000 tonnes/day and operated at a total direct operating cost of less than $20/tonne.INTRODUCTION The Cinola orebody was discovered in 1970. It is situated approximately in the centre of Graham Island, the largest of the Queen Charlotte Islands. It represents the mid to upper levels of a hydrothermal precious metals system, characterized by intense brecciation and silicification. Gold is associated with finely disseminated sulphides in a breccia matrix and in free form in numerous quartz veins.Ownership of the property has changed hands a number of times, and previous attempts to bring the property to production have failed. Two critical factors have frequently been blamed for difficulty in creating a successful project: namely, process and environment factors, hence the title of this paper.City Resources (Canada) Limited (""City"") acquired the property in 1986, and commenced an aggressive campaign to verify ore reserves, to carry out metallurgical research and to address environmental issues.PROJECT OVERVIEW When the Cinola orebody was discovered, the significance of hydrothermal mineraliza¬tion associated with crustal plate boundaries was not recognized, and for several years, the orebody was considered an uneconomic curiosity. If the type and location of orebody sought by many companies engaged in gold exploration were to be specified, it would probably be a description of the Cinola orebody - it is a large (greater than 1.5 million ounce), low grade (2.45 gm/tonne), refractory ore reserve associated with the Pacific rim crustal plate boundary. The industry appears to have recognized in the past few years that its future lies in the exploitation of such orebodies, and is prepared to come to grips with the technical problems associated with such ores. In this sense, the Cinola orebody might be considered to have come of age."

Jan 1, 1989

By Gilles Rousset

This paper presents laboratory experiments conducted on hollow cylinders samples. The advantage of such a geometry is to approach in situ conditions around cylindrical openings (lined galleries, boreholes, ...). Many authors have been interested in this kind of problem, especially for borehole stability applications (for references see Guenot 1987). However, as long as we know, time-dependent behavior has not been well studied. For this purpose, we have set up two different types of tests on a deep clay : - Quick unloading test, to assess the influence of unloading rate on mechanical response and the failure modes. - Creep and relaxation test, to compute the time dependent overall deformation of the hole wall as well as to plot long term convergence-confinement pressure curve. The experimental results are then compared with those given by a theoretical model developed in our laboratory, well fitted with the tested material.

Jan 1, 1989