Search Documents

By M. C. van Blerck

Since its introduction in 1956, the capital allowance has been increased and its scope widened. At present the allowance is 10% in respect of two categories of gold mine (post-1973 and other deep level mines) and 6% in respect of natural oil mines. The allowance is a significant incentive encouraging the development of new mines, to the benefit of both the fiscus and the South African economy as a whole. A strong case can be made for increasing the amount and the scope of the allowance. The Margo Report recommendation that the allowance should possibly be replaced with a system of direct grants is, in theory, neutral. However, practical difficulties exist with cash grants and there is concern with the implications elsewhere in the Margo Report that the capital allowance is excessive and that, as a consequence, such direct grants will represent an effective reduction in this incentive. I believe that the best course of action would be the retention (and enhancement) of the capital allowance and the expansion of its scope.

Jan 1, 1988

By J. W. Smith, J. Van Dusen, A. Papachristodoulou

"As part of a study to evaluate factors affecting tankroom air quality, the mechanism of aerosol generation from bursting bubbles in electrowinning operations has been investigated. Typically 2 to 3 mg/m2.s are produced in zinc tankrooms. Analysis shows that the rate of production of film drops (geometric mean diameter - 2 urn] increases with decreasing bubble size, and that jet droplets (geometric mean diameter - 20 um) are not produced with gas bubble larger than - 4 mm. Both mechanisms of drop formation and current efficiency are affected by surface active agents, with an over-all reduction in emission of up to 60% to 70% being achievable. A source control system which does not adversely affect electrolyte properties is always preferred, and coalescence of all gas bubbles in to a continuous stream of gas at a single point on the electrolyte surface would eliminate aerosol emissions. This objective was the basis for design of a coalescence device which, in laboratory tests, reduced the emission rate by over 95%.The control device fit s over the electrodes in the electrowinning cell and is partially immersed in the electrolyte. A number of changes in the design which resulted in significant improvement in the performance of the device are reported.Field tests have shown that only about 75% of the aerosol below 10 um can be eliminated by coalescence. The remainder (up to 95% of the total) is controlled by coalescence of droplets, by impaction on the exposed collector surface and gravitational settling.The device does not interfere with operation of the tankroom, handles the effect of surges in power during harvesting, and is simple and inexpensive to maintain. IntroductionDuring the electrowinning of metals (such as zinc and copper) gases are evolved along the electrode surface forming small bubbles. The bubbles travel upwards and burst on the electrolyte free surface generating, in this way, small droplets. Because the electrolyte is often highly acidic or contains toxic materials, the whole process can result in the formation of an aerosol in the atmosphere above the electrowinning cells which poses a serious health hazard to workers in the area, and corrodes equipment."

Jan 1, 1988

By Diane M. Doyle-Coombs

In late July 1985, air samples from a sealed portion of the Quinland coal mine in West Virginia showed the presence of carbon monoxide (CO). Mine Safety and Health Administration (MSHA) personnel concluded that a fire was burning behind the seals. Since an imminent danger existed, the mine operator was given a closure order. The gases behind the seals were monitored and almost 2 million ff of carbon dioxide (C02) gas was pumped into the sealed area to stabilize the environment. Sixteen days after the closure order was issued, MSHA allowed the mine to return to production. Approximately 1 yr later, mine management submitted a seal breaching request to MSHA in order to drive a set of entries to further develop the mine. The Bureau of Mines established a sampling strategy and monitored gases from behind the sealed area during the breaching operation until the atmosphere was safe. This report is an account of the seal breaching conducted by the mine, MSHA, and the Bureau. The logistics of this event, the sampling strategy, and the equations applied could be used by the mining industry in future breachings or mine recovery operations. Time to reenter the area was calculated by using the methane (CH4) concentrations sampled at the discharge of the seals. Tracer gas was used to verify the ventilation flows through the area.

Jan 1, 1988

By S. Bhattacharya, M. M. Singh

The Surface Mining Control and Reclamation Act of 1977 (SMCRA) requires under-ground coal mine operations to prevent "material damage" to renewable resource lands caused by subsidence. However, what constitutes material damage is not defined. This paper discusses the applicable criteria for agricultural lands, forests and grazing lands, surface water bodies, and ground water aquifers. Although data on the subject are limited, an attempt is made to present quantitative guidelines to distinguish between moderate and severe damage due to subsidence.

Jan 1, 1988

By R. Andre, R. L. Grayson, T. Simonyi

"Results from research directed at determining the reason(s) for the ""rank factor"" in correlations between coal workers' pneumoconiosis incidence and coal seam of employment are presented. Using compliance dust samples collected from two longwall panels operating in coal seams of widely different rank, respirable particles were identified by mineral species under manual scanning electron microscope (SEM) energy dispersive x-ray (EDX) analysis and then further characterized by their physical diameter, general shape, and periphery angularity. Size fractional, mineralogical variations are presented.Of primary significance, the percentage of mineral particles from the higher rank coal seam that were uncontaminated by non-stoichiometric elements for a specific mineral species was twice that of those in the lower rank seam. The relationship held for each mineral species, including quartz. This fact may form the basis for the ""rank factor"" known to exist as well as provide a reason for the contradictory role of quartz and other minerals in previous CWP studies.An important subsequent research priority is now focusing on determining the percent¬age of all respirable dust particles that are minerals versus single-phase organic or multi-phase organic-inorganic complexes. This effort will be accomplished usingautomated SEM-EDX. The mineral purity factor will be developed further, but additional emphasis will be focused on determining the extent of inorganic inclusions in organic particles."

Jan 1, 1988

By Barry Welch, Kai Grjotheim

"The capital intensive nature of the present process for aluminium smelting, the low productivity per unit reactor, and pressure to reduce the electdcal energy demand have motivated the search for an alternative process. Optional routes include carbo-thennal reduction of alumina (using an alloy phase immediate), chlorination followed by electrolysis of aluminium chloride, and electrolytic decomposition of alumina using inert electrodes. Materials performance and reactor design constraints have been a major limitation for alternatives. However parallel research has led to considerable advances in the process efficiencies and scale of both the Bayer process and the Hall-Heroult cells.Future development of alternatives is dependent on breakthroughs in Materials Science such as the development of stable conducting anodes and stable wettable cathode materials. However if successful it is probable that some spin-offs will be retrofitted to existing cells. Therefore the basic Hall-Heroult technology will continue as the dominant process for at least the next half century.IntroductionThe present Bayer/Hall-Heroult process for production of aluminium is just over 100 years old. Frequently, during the century of its technological development questions have been raised as to whether it is the ideal route for metal production. The questioning was particularly intense in the period between the mid-1950s and the mid-1060s when the limitations of the Hall-Heroult electrolytic stage were evident. Then the cells were only 30 to 35 % efficient with respect to the utilisation of the hydro-electricity (requiring 16 18 kWh/kg, thus making it strongly dependent on cheap electrical energy), while the size of cells being installed were 80 to 130 kA. Hence the process was capital intensive, the productivity per reactor volume low, and the process was labour intensive (requiring about 15 man hours per tonne of aluminium). In addition, the use of pitches for Soderberg anodes and the fluoride electrolyte were creating problems through emission. At that time material science had paid little attention to the manufacture and use of carbonaceous materials or the development of alternatives that were corrosion resistant to cryolite or liquid aluminium. Hence cell lives were short - typically 600 to 1000 days - thus adding to operating costs. Thus the grass over the fence, as foreseen in 1960s vintage crystal balls appeared much greener for alternative processes."

Jan 1, 1988

By W A. van der Westhuizen, Beukes G. J, Vermaak J. J

Large parts of the arid northern Cape Province South Africa are blanketed by Quaternary cal- crete under which potential base-metal ore- deposits may occur. In an attempt to examine the nature of the distribution of such ore-re- lated elements in a calcrete environment, calcrete and soil samples from the copper-nic- kel prospect at Jacomynspan and the copper- zinc deposit at Copperton were examined. Both deposits form part of the Namaqua mobile belt. CALCRETE GENESIS In Southern Africa calcrete is restricted mainly to the western two-thirds of the sub-continent, south of the latitude 17¦ S. Various models have been put forward to explain calcrete genesis and Goudie (1973) and Netterberg (1969a) give detailed discussions on this topic. The most popular model for calcrete genesis is one of pedogenic origin. McPherson (1979), Watts (1980), Wright (1982), Arakel (1982), Netterberg (1969a), Goudie (1973) and Multer and Hoffmeister (1968), amongst others, support the hypothesis of calcrete formation by carbonate precipitation from downward percolating calcium carbonate rich soil waters. Calcium carbonate is usually initially precipitated as nodules or grains which can develop to form more compact layers.

Jan 1, 1988

By Guenter F. Lehmann

This report summarizes the results of the development and testing of a prototype monorail suspended bridge conveyor (MBC) system as a method of continuous haulage In underground mining applications. Included are the results of full scale, surface and underground testing of the complete MBC system. Conclusions drawn from these results, together with recommended modifications, supports the viability of the MBC system.

Jan 1, 1988

By Enichlmayr E

Lignin grouts are cheap and easy to get. They have some desirable properties, but they aag less used now because environmental pollution is often caused by Cr from the lignochrome component of the grout. Their usefulness was researched in an earlier paper on lignin as a grout from other viewpoints. A non-toxic grout FUL was made composed of furfural, urea and lignin. After initial tests, including tests by spinning regression design, some response equations in which FUL's properties are described were obtained. Optimum formulations have been established by using optimization methods based on response equations. The engineering quality was assured by formulations whose properties were measured in further tests. The mechanical feature of gelling sand was measured by means of triaxial tests. This provides a basis for using FUL grout in-situ. Finally, an in-situ experiment on FUL was completed successfully. The results were that cracks in stratum were filled or blocked, the gelling of FUL had high strength, and low permeability and consolidation were achieved.

Jan 1, 1988

By N. S. Dalal, X. Shi, V. Vallyathan

"INTRODUCTIONThis paper summarizes our recent investigations of the potential role of silicon-oxygen based free radical species in the biochemical mechanism of the lung injury caused by the inhalation of freshly fractured silica. The impetus for this study came from the following observations. Inhalation of crystalline silica is associated with the development of acute and chronic silicosis. Chronic silicosis is characterized by the development of sharply marked concentric fibrotic nodules in the lung. This occurs over a period of several decades with the development of progressive respiratory impairment. In contrast, acute silicosis is manifested by the filling of the alveoli with an amorphous lipoproteinaceous exudate within a short period after exposure, and rapid development of respiratory disability often leading to fatality. Most studies on the pathogenesis of silicosis have focused on the elucidation of cellular mechanisms of cell injury and the development of chronic silicosis. Because pulmonary responses to crystalline silica are distinctly different for · the acute and chronic silicosis, we hypothesized that the acute response is associated with some unique properties of ·freshly formed silica particle surfaces, due to the formation of some reactive chemical species caused by the rupturing or the silicon-oxygen bonds. In occupations involving drilling, tunneling and sandblasting operations acute silicosis can be correlated with this unique surface reactivity of silica. The formation or reactive species was demonstrated, using electron spin resonance (ESR) spectroscopy (Dalal et al., 1986; Fuibini et al., 1987; Hochstrasser and Antononi, 1972). Grinding of quartz crystals under ultra high vacuum (10-10 torr) leads to the formation of Si- and SiO• radicals and these radicals are quenched by exposure to air and other gases (Hochstrasser and Antonini, 1972). ESR signals have also been reported from micronized quartz samples that were evacuated at 413 K (Bolls et al., 1983). In order to find a more direct relationship of such radicals to acute silicosis, we made ESR measurements on quartz dusts freshly ground in ambient air and found- that indeed grinding under ambient environment leads to the formation of the Si• and SiO• type of radicals which decay on storing the dusts in air or in biological buffers (Dalai et al., 1986; Vallyathan et al., 1988). The Si• and SiO radical formation on grinding has also been reported by Fubini et al. (1987). In addition, we recently found that •OH radicals are generated in aqueous suspensions of freshly ground quartz (Dalai et al., 1988; Shi et al., 1988; Vallyathan et al., 1988). We have subsequently carried out detailed cytotoxicity and biological assays on freshly made as well as aged quartz dusts. As summarized below, the results provide new insight into the biochemical mechanism of acute silicosis."

Jan 1, 1988

By A. McCracken

Probabilistic methods for assessing the reliability of engineering systems in mining are the way of the future. So agreed the delegates of a recent short course on the subject, entitled 'Reliability-based Approach in Mining engineering Design'. This was a very successful five-day technical course sponsored by The South African Institute of Mining and Metallurgy and held at Mintek from 7th to 11th March, 1988. The main lecturer for the course was Milton E. Har, Professor of Geotechnical Engineering at the School for Civil Engineering of Purdue University, Indiana, USA. Professor Har was ably assisted by Dr Dirk van Zyl, a former student. Science quiz Teams of pupils from 37 schools within a radius of 12 kilometres of the Council for Mineral Technology (Mintek) competed in a science quiz held by Mintek at its headquarters in Randburg on Tuesday, June 7th, 1988.

Jan 1, 1988

By Don C. Warrington

This paper describes a new wave equation analysis program called ZWAVE, which is a program specifically for external combustion hammers. The program is de-scribed in detail, the discussion dealing with topics concerning the program such as 1) the numerical method the program uses to integrate the wave equation, which is different from most other wave equation programs; 2) the modelling process of both cushioned and cushionless hammers; 3) the automated generation of mass and spring values for both hammer and pile; 4) the method of dealing with plastic cushions; 5) the use of a recently developed model for computing shaft resistance during driving; 6) the computation and generation of values based on basic soil properties such as shear modulus, Poisson's Ratio and soil density; 7) the completely interactive method of feeding data to the program; 8) the method used to compute the anticipated rebound and the energy used to plastically deform the soil; and 9) the format of the inter-active input of the program and the program's output. Sample problems for the program, along with comparison of the program results with data gathered in the field, are presented.

Jan 1, 1988

By James W. Reil, Douglas A. Anderson

Common wisdom has it that a blast which breaks rock efficiently should-generate less ground vibration. In practice, however, this idea has not been-rigorously tested. In a previous paper presented at an SEE meeting[1] we described a method for-controlling vibration using delays. The method is very effective in controlling-annoying low-frequency ground vibration. We noted that observed ground-vibration differs in some respects from that predicted by adding single-charge-waveforms.

Jan 1, 1988

The paper deals with the problems of grouting methods for fissured-porous rock. The paper describes design procedure, injection process patterns and hydrodynamic testing techni- que to plan grouting programs for fissured-porous aquifers. A number of case histories is given to illustrate the imp- lementation of developed methodology at various mining pro- jects.

Jan 1, 1988

Underground measurements, observations and computed simulations, started a long time ago were concerning the study of : - occurence of typical rockburst, - inducing, stretching of main fractures in the roof of caved longwalls. They made obvious a foundamental phenomenon of inducing of strata fractures involving contact be- tween two layers quite different in their elastic characteristics : coalseam and rocklayer.. The start of primary cracks in maximum abutment zone takes place in the rock near the contact surface. It is opening of crevasses induced by traction stress component resulting of difference of rigidity of both materials and no sliding on in- terface. Occurence and stretching of these crevas- ses are a rheological phenomenon so that the rate of advance and stops of the face influence the distance between the crevasses and the stretching of these ones. The characteristics of these cracks in space and time affect mining conditions. So it is for fractures proximity and expan- sion inducing eventual blocks formation in longwall roofs in front of faces, for depth and delay of road- ways ribsides fracturing, inducing some rockbursts. In longwalls roofs, cracks initiated in front of a face can be either quite close or quite distant each from the other one, according to the depth of crushed coal in front of the face, which af- fects also extension of the cracks.

Jan 1, 1988

By M. K. Matthews

The use of backfill has important environmental control implications which, although frequently overlooked, can be both beneficial and problematical. Where backfill is widely used, the reduction in stope heat load and improved air utilization influence the overall mine ventilation and refrigeration requirements significantly. A programme of work examining in detail all the environmental consequences of backfilling is currently underway at the Environmental Engineering Laboratory of the Research Organization of the Chamber of Mines. This paper gives an overview of the work and presents some findings. In so doing, the environmental implications to be considered when backfilling are highlighted.

Jan 1, 1988

By Will D. P

A 328 m, 2.4 m diameter raise-bored shaft has been equipped with a modular ladderway system to provide a second means of egress from Aberfoyle's Hellyer Mine in Tasmania. The modular ladderway consists of platforms, ladders and service pipes assembled at the surface and progressively lowered down the shaft. This system provides a rapid, safe and economical non-entry approach to equipping a shaft. The modular construction and single suspension allows for future extension or for reuse in another shaft.

Jan 1, 1988

By A. Montini, M. H. Moys

A technique for the measurement of slurry consistency inside a grinding mil is described. The rate of slurry drainage from a sensing probe mounted through the mil shell is measured and correlated with the percentage solids of the slurry discharging from the mil. The response time of the measurement(obtained on a pilot bal mil) is compared with the response time of the viscosity of the mill discharge. It is shown that the new measurement should allow much tighter control of the mil behaviour, with concomitant savings in the consumption of power and steel.

Jan 1, 1988

By J. A. Wates

Stope backfilling in South African gold mines uses the coarser cyclone fraction of the gold tailings. The disposal of the overflow from the cyclones, which is finer and of higher moisture content than normal gold tailings, presents some problems. This paper describes an investigation undertaken to define the parameters that are required for a quantitative and qualitative assessment of the operation and stability of slimes dams built of such material. However, seeing the investigation was conducted on the slimes from only one mine, it is recommended that, until a wider range of data becomes available, tests should be conducted for each individual mine.

Jan 1, 1988

By C. J. Johnson

As the U.S. coal industry moves into the next century, it is becoming more apparent that the effective application of new technology is the only way it can remain competitive in the energy marketplace. Examples of this emphasis are with us today in such diverse areas as face-ventilation and excavation-equipment applications. The focus of this new technology is directed toward improvements in health and safety, cost control, and productivity. Room-and-pillar mining accounts for approximately 80% of the nation's underground coal production; this percentage is not expected to decrease markedly in the near future. As such, this paper analyzes the impacts of the changing technological climate on future room-and-pillar operations by comparing a base-case section (current) to three scenarios incorporating new or emerging technology. A microcomputer-based comparative analysis will reflect the changes in section production and costs.

Jan 1, 1988