Search Documents

By D. S. Cavers

INTRODUCTION This paper discusses aspects of rock engineering applicable to surface gold mines. Discussion particularly centers on areas in which rock mechanics can enhance the mine productivity or profit- ability. Methods of analysis are discussed briefly but for more detai1s the reader is referred to the appropriate references. A team approach to the overall design of the pit generally pro- duces a better result at an overall lower cost. In particular, money is wasted by asking for a "report on slopes" and then input- ting this slope angle into a pit design and economic analysis study without further reference to the geotechnical engineer. Pit slope angle depends on slope orientation, location, pit shape, pre-existing discontinuities and mining methods. Preliminary slope angles can be produced but optimization depends on ongoing inter- action between the mining engineers, geologists and geotechnical engineers. This interaction can a1 so substantially reduce overall design time which may be critical in bringing remote plays into production. Most surface gold mines in North America are in igneous or metamorphic environments. Rock mechanics aspects discussed in this paper will be discussed with reference to these environments al- though most of the principles and comments are applicable to sedimentary environments as we1 1.

Jan 1, 1987

By Garg R. K

Himalayan ranges on the northern border of India are source of many perennial rivers and suitable sites for large dams have been located therein. However, Himalayas are young mountains and comprise of comparatively weaker rocks having adverse geological features like shear seams, thrust zones, minor and major faults and intense jointing. Tehri dam project under construction, is located in lower Himalayas. It envisages construction of a 260.5 m high earth and rock fill dam and an underground power station of 2000 MW (Eight machines of 250 MW each, four of which will be reversible) installed capacity. This dam will be the highest and the underground complex will be the largest to be constructed in India in the Himalayas. The under- ground complex comprises of 25 km of tunnels varying in diameter from 6 m to 11 m and seven large cavities of various sizes, the biggest being 22 m in width, 194 m in length and 65 m in height. Rock formation in the power house complex belong to phyllites having various joint sets spaced from 0.5 m to 3 m. Due to the poor geological conditions and closely spaced net work of large cavities, the planning, analysis and design of the cavities is a challenging job. Many aspects have to be considered in determining the sizes, locations and orientations of the various cavities taking into account the properties and jointing pattern of rock mass, functional requirements and economics. Correct evaluation of loads and forces is necessary for economical design of supporting system for the various cavities. Rock loads on the roof of cavities and their supporting system will be assessed with the help of the latest methods. The stability of the rock mass around the cavity will be evaluated by elasto- plastic method using finite or boundary element techniques. A scheme of field investigations, laboratory tests and instrumentation for deter- mining rock properties in preconstruction stage and for monitoring behaviour of the underground cavities during and after construction is envisaged.

Jan 1, 1987

The elements of consistent structural de sign models for underground structures are explained. Such models should comprise at least ground properties, excavation and support methods, computational models for analysis, failure hypotheses, and in-situ monitoring. The fundamental characteristics of the interaction between ground and support are investigated. Then, plane strain models for soft ground tun- nelling and design models for rock tunnelling employing stress release at the tunnel face are elaborated. Some numerical evaluations are gi- ven in diagrams, comparing approaches of dif- ferent authors. Comments are presented on nume- rical three-dimensional models (visualized by structural models for mining in rock salt), on the interaction of in-situ monitoring and design, on structural safety for underground structures, and finally on the general develop- ment of structural design models in geo- Techniques.

Jan 1, 1987

This paper briefly discusses the negotia- tion of the more important provisions in agree- ments for exploration and mining rights with Pacific countries. LAND RIGHTS Land rights are complicated and sometimes controversial in many of the Pacific countries. In some countries, a company will have to deal with land owners directly; in others, the government will act as intermediary. Inevit- ably, a company will have to deal with both. Mining companies need to be sensitive to the culture and particular interests of the land owners and of their history in defending their rights. The issues are too complicated to be dealt with here. Some mining companies have spent, and will continue to spend, considerable time trying to understand them. It will " require patience, perseverance, sensitivity and unflagging optimism. The better advised companies will ensure that their local repre- sentatives get to know the land owners, under- stand their concerns, and will pursue a policy of keeping them informed on a regular basis of all of the company's activities and proposed activities. Good community relations are the keystone for good mining operations in the Pacific. Most countries will require the submission of an environmental impact statement so that they will know in advance what effects a pro- posted mining operation are expected to have on the environment and how it is intended to deal with them. They will also want to approve the company's environmental reclamation and rehabilitation plan. Let's face facts right away - mining, by its very nature, is not going to improve the environment. There will be waste discharges, emissions and deposits. They will affect the land, air and water and hence human, marine and animal life and vegetation. There will be sounds and odours and the esthetics of mining operations, though perhaps pleasing to geolo- gists and mining engineers, will not please Others.

Jan 1, 1987

By Dennis P. Bryan

The southwestern United States has an abundance of natural lightweight aggregate (NLA) deposits of volcanic origin that are being used in the construction industry within the region. New Mexico, Arizona, Nevada and California utilize NLA in portland cement concrete and concrete masonry units for weight reduction and related economic reasons. The geological environment of the western United States is amenable to the occurrence of natural lightweight rocks because it contains Tertiary and Quaternary volcanic products that include low-density glass and vesicular material. There are two major classical types of natural lightweight materials of igneous origin; pumice and cinder. These account for the vast majority of volcanic rocks that are presently utilized as NLA. Pumice is an ejecta product generally found as part of tuffaceous units associated with nearby siliceous volcanic centers. Cinder, also an ejecta product, is associated with mafic volcanics and is most often found as a cinder cone. Both are highly vesicular. A third type of natural lightweight material, though also associated with siliceous volcanics, is less vesicular than pumice. It is best described as being a slightly pumiceous rhyolite or rhyolite-tuff breccia that occurs as a siliceous dome or tuft unit that is most likely to be glassy. Uses of these natural lightweight rocks center on the construction industry where they are utilized in lightweight portland cement concrete and lightweight concrete masonry units. The major reason for usage in portland cement concrete is cost saving effected by weight reduction in high-rise construction. The major usage in concrete masonry units, or "block", is for weight reduction that enables a mason to lay more lock.

Jan 1, 1987

By D. S. Choi

This paper presents the results of geomechanics work applied to the longwall operation. The mining method was successfully adapted to US mining conditions resulting in an improvement in safety and productivity. The paper deals with various geomechanics problems associated with geologic and mining conditions.

Jan 1, 1987

By A. Mcdonald

"An X-Met Analyzer was purchased from Outokumpu in late 1983for use in the Hudson Bay Mining and Smelting smelter. Its first use was in the fuming plant to give zinc assays of each charge of slag tapped from the fuming furnaces. This quickly told the operators exactly when each charge had reached its economic tap-out point, and gave supervision a fool-proof method of identifying good operation. These and other factors led to major improvements in coal utilization in the fumers and to major increases in zinc oxide production. A second unit was later purchased for the reverberatory furnace to give silica and iron assays of the slag, and these were used to make adjustments in the feed composition to maintain the desired SiO2:Fe ratio in the slag. Since purchasing the units for the furnace, the oil consumption and copper content of the slag have dropped significantly. IntroductionSmelters have lagged far behind concentrators in process control by mean s of rapid product analysis. The on-stream X-ray analyzer was developed about seventeen years ago, and soon concentrators around the world were getting assays of the incoming ore, .concentrates and tailings every fifteen minutes, and using these to control reagent additions and other process variables. Almost always, the concentrate grade and recovery improved.In smelters, product streams are solids or molten materials, not the more easily handled slurries, and until seven years ago no inexpensive equipment was available to provide rapid analysis of this type of material. In approximately 1980, several companies developed instruments based on irradiating solid samples with low-intensity gamma rays from radio-isotope sources, and measuring the secondary X-rays emitted from different elements in the sample to provide an analysis of the elements desired.The smelter staff had a close look at what was needed and listed the following points as being critical:1. ability to provide Zn assays of a sample of slag within 15 minutes of taking it, in order to achieve optimum fuming times (zinc fuming , being a batch process, had the greatest potential benefit from rapid slag analysis);2. ability to give Cu and Fe assays on the slag, and on other smelter products, such as matte and converter slag;3. ability to give Si02 assays since the SiO2 content of the slag has a strong effect on fuming rate; and4. ability to stand up to an industrial atmosphere such as exists in the fuming plant."

Jan 1, 1987

By B. N. Whittaker

The paper briefly reviews the type of support and stability problems encountered in mining tunnels in U.K. Carboniferous rock conditions, particularly the Coal Measures where almost all such tunnels are located. Stability prediction of mining tunnels is discussed and a computer-based model which deals with stratified rock conditions is described. Various schemes for monitoring the stability of mining tunnels are examined and the application of the results discussed. Comparisons between predicted and measured Closure values are presented for a major Coal mining tunnelling project at Selby in the North Yorkshire Coalfield. Conclusions are drawn concerning the application of the present prediction technique together with the importance of underground monitoring. Examples of different types of mine tunnel stability problems encountered in the U.K. Coal Measures are discussed and comments made on the secondary effects of tunnel peripheral rock weathering and corrosion of the associated support systems.

Jan 1, 1987

By M. K. Quinn, R. D. Chaffins, A. W. Khair

This paper presents an analysis of the effects of topography on static and dynamic ground movements and severity of damage inflicted on surface structures. A typical site containing varying topographical features (i.e., mountains, hillsides, valleys, and flat bottom land) representing the northern Appalachin region was chosen for the study. Typical subsidence monitoring techniques were employed. Frequent measurements were made as the face advanced.

Jan 1, 1987

By Joseph M. Keane

A number of innovative techniques exist for solving heap leaching problems in special situations. Some of these techniques have been successfully applied and others await an opportunity for application. Discussions in this paper will deal with gold heap leaching under severe thermal conditions, in tropical rainfall circumstances, in the absence of fresh water, and in other situations removed from the ordinary. CLIMATIC CONSIDERATIONS The success or failure of precious metal dissolution operations may be strongly dependent upon proper attention to the influence of climate. A few examples are given in the following paragraphs.

Jan 1, 1987

By R. I. Pennington, J. L. Vanderbeek

Investigations have been conducted at Chino Mines Co. into the effect that SAG mill recycle material (critical size) exerts on SAG mill throughput and specific energy requirements. Tests were conducted on laboratory, pilot, and plant scales to evaluate the merits of alternative treatment options. Removing critical size material from the SAG mill circuit has been shown to improve new feed rates by 84% with a reduction in specific energy (kWh./t) of 88%. Test results obtained to date are presented.

Jan 1, 1987

By Eaton R. A

The design of most underground mining machines shows little evidence of regard for ergonomic principles and operator comfort. Likewise, efficiency and ease of operation often appear to have been given little consideration in machines where ruggedness and simplicity have tended to dictate the configuration. Improvements in productivity are amongst the benefits to be gained by a different approach to machine design. The paper describes the philosophy and features of a test bed Load-Haul-Dump Vehicle undergoing trials at Mount Isa Mines. This machine is the outcome of a Research and Development Programme conducted by the Department of Mechanical Engineering at the University of Queensland and Mount Isa Mines Limited. The diesel powered test bed features an enclosed, air conditioned cabin, with a suspended operator's control station and electrically operated controls. An electronically controlled hydrostatic transmission incorporating wheel slip control, is another innovation. The performance and operator acceptance of the machine has led to adoption of most of the concepts in a new machine now being put into production.

Jan 1, 1987

By Lawson F

Pyrite concentrate and calcine from the Nanjing Lead-Zinc-Silver Mines, China, were leached with aqueous cyanide and thiourea solutions. More than half of the contained gold and silver was able to be extracted from the roaster calcines. The very fine dissemination of precious metal grains, high roasting temperature (850 - 900°C) and residual sulphur are believed responsible for the Iow extractions.A recovery of about 70 per cent for both silver and gold was able to be obtained with cyanide and with thiourea leachants when the pyrite was roasted in the laboratory at temperatures between 600 and 650°C.Thiourea, as an alternative leachant, has received much attention recently and a series of constant potential leaching tests was conducted.When the thiourea to formamidine disulphide mole ratio was about two, the precious metal extraction was greatest. In the Nanjing calcined material, this occurred at a potential of about 210 mV relative to a standard calomel electrode.

Jan 1, 1987

By C. W. Smith

The Bureau of Mines conducted laboratory-scale beneficiation tests on a sample of corundum gneiss from Montana to devise a method for beneficiating corundum for use as a substitute for refractory-grade bauxite. A flotation process utilizing petroleum sulfonate as the collector in an acid circuit was devised. Results showed that two flotation schemes each produced a concentrate exceeding the national stockpile specifications for calcined bauxite. From a feed containing 28 pct corundum concentrates containing up to 92.5 pct alumina (A1203) were produced with a corundum recovery of 78.5 pct.

Jan 1, 1987

The latent conditions clause in various general conditions of contract have traditionally proved to be a source of significant disputes in tunnelling contracts, even when extensive geotechnical investigations have been carried out at the tunnel site and a report of these investigations provided with the tender documents, informing the contractor of the nature and extent of subsurface conditions likely to be met with during execution of the works. This paper discusses the contractual aspects of the new latent conditions clause in the recent Australian Standard AS 2124-1986, General Conditions of Contract, in relation to tunnelling contracts. A comparison of this new clause is made with other latent conditions clauses in general conditions of contract in use in Australia and other commonwealth countries. It is seen that the new latent conditions clause in the recent Australian Standard 2124-1986 has, by providing for a reasonable apportionment of risks, attempted to minimize contractual disputes relating to latent conditions in tunnelling contracts and to provide a satisfactory basis for quick and efficient settlement of such disputes should they arise during execution of these contracts.

Jan 1, 1987

By N. M. Grant, W. G. Prast

Jamaica has extensive deposits of marble, gypsum, and limestone, offering prospects for commercial sales to nearby US markets, notably the Gulf Coast and Southeast. Stare-owned and private Jamaican industrial minerals producers have made limited sales to date but expect to increase exports during the balance of the 1980s. Restraints include Jamaican government controls on access to essential foreign exchange for new capital investments and distribution of profits. Jamaican efforts to identify market opportunities in the US are reviewed, and the outlook for further exports of carbonates is discussed.

Jan 1, 1987

By J. C. Kerkering

The Bureau of Mines used mathematical reliability theory to define, for use in the mining industry, the concepts of risk, safety, reliability, hazard, and mean time between accidents. In this report, the definitions are explained theoretically and illustrated by application to actual underground mine accident data extending over a 9-1/2-year period. The theoretical development proceeds along two parallel analytical paths. For each line of reasoning, the data are presumed to be independent. If they are not, the analysis stops, although there are interesting implications when dependency is demonstrated. The first method uses the elapsed times between accidents as the basic data. These elapsed times are fitted to a negative exponential distribution function using least squares and yielding the function parameter, P1 The P1 is used to form the Poisson distribution function for the data, which is then used to define the safety-related concepts. The second method uses the maximum likelihood estimator to formulate a Poisson distribution function for the data. The function is tested for adequacy by a goodness-of-fit test; if the fit is acceptable, the Poison function is used to define the concepts. Both methods were applied to the data base, yielding nearly identical results.

Jan 1, 1987

By P. C. Cochrane, I. S. Clelland, S. H. E. Phillips

Geological and hydrological conditions in the strata overlying the Salado Formation vary considerably in the Carlsbad, NM, area. The first four shafts sunk at International Minerals and Chemical Corp. (IMC) property have been located in competent and essentially dry conditions, while other shafts on adjacent properties have had such adverse conditions that ground freezing has been chosen as the water and ground control technique for shaft sinking. At the location of the IMC No. 5 shaft there has been extensive erosion and salt dissolution in the Rustler Formation, leading to collapse of some zones of the strata. Both ground freezing and pregrouting were considered as alternative methods of stabilizing the extremely poor ground conditions and controlling the potentially very heavy water inflows. It was decided that pregrouting the shaft was feasible and would offer substantial cost and time saving over a ground freezing technique. This paper describes the pregrouting techniques used and illustrates the requirement for flexibility in a grouting program so that it can be modified to reflect any new or additional information obtained during the progress of the grouting.

Jan 1, 1987

By A. C. Scott

A detailed fundamental model of a zinc electrowinning cell has been developed and validated for both steady state and dynamic simulations. This model was used to investigate the effects of a range of operating variables and to find their optimum values. As well as providing useful design information for a planned upgrading of the EZ refinery, more generally it demonstrates the potential benefits to the minerals industry of the applications of modern CAD flowsheeting techniques. The SPEEDUP equation oriented CAD package was found most suitable for this task as the user can easily generate models specific to his site with any number of components and mixture properties.

Jan 1, 1987

By Hagarty KA

At the northern margin of New Guinea there is a fundamental problem related to the relative timing of arc- continent collision(s) represented in the Papuan Fold-Belt (PFB) and backarc spreading in the Caroline basins. New fission track dates from basement and sediments within major anticlines of the PFB indicate that uplift occurred at 4.0 ¦ 0.5 Ma. The timing is consistent with the fold and thrust shortening (more than 100 km) of the PFB which occurred in the Late Miocene/Early Pliocene as evidenced by the deformed Miocene carbonates and Pliocene molasse deposits. However, in northern Papua New Guinea, earlier work has suggested that ophiolite emplacement and associated metamorphism occurred in the late Oligocene/early Miocene.The evidence suggests that the late Miocene/early Pliocene deformation was of considerably greater magnitude than the earlier obduction event. The Caroline Plate lying north of New Guinea has been interpreted as a backarc basin which commenced spreading in the Eocene and ceased spreading in the Late Oligocene (about 28 Ma). The remnant arc presently docked to New Guinea was active in the Eocene and Oligocene and is believed to be the arc related to the formation of the Caroline Plate. The cessation of spreading of the Caroline Plate has previously been interpreted to be due to arc continent collision during the Late Oligocene/Early Miocene, but such a collision is now known not to have occurred. In the Cretaceous and Palaeocene subduction was to the south beneath New Guinea, but "flipped" in the Eocene to give a north-dipping subduction zone far to the north of New Guinea, driving Caroline Plate backarc extension. This backarc basin reached a limiting size at about 28 Ma resulting in the end of subduction. With the continued northward movement of Australia, Mesozoic oceanic crust was obducted southward onto the New Guinea margin in the Late Oligocene/Early Miocene. In the Miocene south-dipping subduction beneath New Guinea commenced until the now extinct Caroline Plate arc collided with New Guinea in the Early Pliocene, causing extensive regional compression and sinistral strike-slip faulting. This new tectonic framework suggests that backarc basins reach a limiting ridge-trench distance of 1000-1500 knm, beyond which "subduction-pull" cannot drive further spreading so subduction and spreading are terminated.

Jan 1, 1987