Search Documents

By R. E. Ray, J. W. Stevenson, J. A. Berry

Conventional concrete block plastered with a cementitious coating is the most common material used in the construction of permanent stoppings to direct airflow in underground mines in the US. All mines experience various degrees of strata convergence depending on depth of overburden, geological conditions, and type of roof support employed. Strata convergence will cause cracks and joint openings in masonry stoppings, resulting insignificant air leakage losses. Where strata convergence is severe, complete structural failure of the stopping can ultimately occur. Reconstruction of damaged or destroyed stoppings adds expensive overhead to mining operations, and even greater expenses are incurred from the additional fan horsepower required to overcome leakage losses. Ideally, a stopping should maintain high resistance to airflow while yielding to strata convergence. By properly incorporating a polyisocyanurate rigid foam material within the masonry block structure, stopping service life can be increased in mines experiencing strata convergence problems such as floor heave, roof loading, and lateral rib movement.

Jan 1, 1986

By J. M. Pachter

Property sales and acquisition are prominent features of today's coal industry. Before selling or buying a site, a company must know the property's economic net worth. Any evaluation of economic net worth would be inadequate if determinations of a property's environmental liabilities and costs were omitted. Short-term and long-term costs can result from liabilities related to reclamation, water treatment, subsidence, and hazardous waste disposal. A structured, interdisciplinary approach can aid in the delineation, summation, and scheduling of these costs and liabilities.

Jan 1, 1986

By L. S. Beck

"IntroductionThe Beaverlodge District is an important mineralogenic province of pitchblende and occupies about 1300 square kilometres centred on Beaverlodge Lake near the north shore of Lake Athabasca in northwest Saskatchewan (Fig. 1). Uranium City is the main settlement of the area and is serviced by scheduled aircraft from Edmonton, some 700 km to the southwest, and from Prince Albert which lies a similar distance to the south.During the summer, boats and barges supply the area from the railhead to Fort McMurray via the Athabasca River and Lake Athabasca, a distance of about 550 km. For the past few years a winter road has been maintained across Lake Athabasca to Cluff Lake to connect with Highway 155.The topography of the area is typical of the Precambrian Shield with generally low relief and a disorganized drainage of numerous lakes separated by hummocky rock ridges, muskeg and drift-covered areas. Local topography in the area is, however, extremely rugged, particularly south and east of Beaverlodge Lake, where resistant rocks form prominent hills and ridges extending as much as 180 m above lake level. Rock exposures are abundant and form over 50 per cent of the land area.History of Exploration and DevelopmentEconomic interest was first aroused by Tyrrell (1896) who described an occurrence of iron formation at Fish Hook Bay; however, subsequent evaluation of the deposit indicated it to be uneconomic."

Jan 1, 1986

By Kennerley P

A significant part of the reserves of the Southern Coalfield lie beneath major water storages and their impounding dam structures. One of the functions of the NSW Government's Dams Safety Committee is to specify the particular mine layouts which can be used beneath the stored waters according to certain guidelines. A study was made of examples of the two different methods of extraction used under the stored waters as proposed by the mining company according to the guidelines and approved by the Dams Safety Committee. Using both pillar monitoring and mathematical modelling approaches it was shown that the recovery of coal from these layouts could be improved while still ensuring the long term stability of both the underground support pillars and the body of the strata. The integrity of the water storages and their impounding structures would therefore not be Affected.

Jan 1, 1986

By D. Constantinides

In 1981 a Zn-Ag-Pb deposit was discovered in the vicinity of Molai, Greece. Subsequently, it was determined to be of the Kuroko type. The geology of various areas in the southeast Peloponnesean Peninsula is similar to that of the Molai deposit. Since favorable geologic criteria are present, absent, or unknown in varying degrees in all areas, it was deemed necessary to classify and rank the prospective areas according to the level of information available. For each level of information, an ore discovery model based on pragmatic exploration criteria was developed, enabling the favorability of occurrence to be calculated for each area. A Monte Carlo simulation was used to calculate the probabilities, the input data consisting of quantitative and qualitative estimates of the geologic criteria for each area. Three levels of information were modeled : Level A consisted of 9 criteria, level B of 12 criteria, and level C of 20 criteria. The three levels of information were tested on the Molai area. The results exceeded expectations, showing the gen¬eral trends which control mineralization at the lowest level of information. With an increase in the level of information, geological trends become more evident and a differentiation can be made between areas containing Cu mineralization, exhibiting a low probability, and areas likely to contain Zn-Ag-Pb mineralization. The models were then applied to the neighboring areas - only level A and B were available.

Jan 1, 1986

The ventilation of a mine is one of the key elements to a successful mining operation. It is, or should be, one of the primary concerns of the mining engineer at an underground mine. Too frequently, however, insufficient thought is given to future requirements. As a result, the mines suddenly find themselves with ventilation problems that cannot be corrected economically, or in short order, and have to suffer the consequences of being on the verge of having units shut down from time to time until the venlilaltion system can be improved. Insufficient ventilation in capital-intensive mining can cause production losses, the values of which far outweigh the significant costs of providing and operating an adequate ventilation plan. Many theories, and techniques in planning and control of underground ventilation systems have been developed over the years . It is the intent of this paper to point out some of the fundamental concepts, from the practical point of view, in the design and operation of a ventilation system, with special reference to underground mines using a room-and-pillar method.

Jan 1, 1986

By V. V. Ershov

Application of computers in the study of mineral deposits pursues two main objectives: 1. obtaining reliable information on the properties of the orebody; 2. providing graphic presentation of this information for its optimal use. These problems are successfully solved if, during preparation of graphic computer software, we apply modern mathematical methods. The present paper treats the problems of using geostatistics for graphic modelling of deposits by means of graphic computers. It should be noted that in this field geostatistical methods may be used for: a) indices evaluation in the nodes of regular grid, or in given blocks, by means of kriging, for its designated purpose; b) for evaluation of accuracy of interpolation methods, traditionally used in computer graphics, and not being optimal.

Jan 1, 1986

By James C. Burrows, Frances Kramer Mesher

Tungsten-containing ores are mined on all continents of the world. China is the world's largest producer and controls the world's largest reserves. The USSR, itself a sizeable producer, is estimated to be the world's largest consumer. The major use for tungsten in the noncommunist world is in production of cemented tungsten carbides for cutting, drilling, and wear parts. Other major uses include lamp wires, steels for tools, and armaments. Real tungsten prices have been in a general decline since 1977-1979 as the tungsten market undergoes basic and lasting structural changes.

Jan 1, 1986

By John W. Scott

INTRODUCTION The design criteria for a particular concentration and dewatering project will provide the formal basis for design of the process, equipment and facilities. These criteria will specify the required capacities and operating schedules for the equipment, as well as the quantity and quality of the feed to be processed and products obtained. The general climatic and geographical conditions at the site, specific information on soil or rock conditions; and applicable design standards and codes will also be included. The design criteria will generally be based on an interpretation of testwork carried out on the particular ore and site, and will thus parallel in detail and completeness this testwork. As the project moves from the early conceptual phases through to final detailed design, the design criteria will be developed and become more detailed as information is generated and made available for use. The design criteria are critical to the design effort as the formal specification to the designer of what and how much is to be processed, what and how much is to be produced, and where and under what conditions. The actual design criteria will be a formal tabulation of the design basis information developed for the project in question. For a preliminary study, this may consist of a single page of data; for a feasibility study several pages and for a detailed design up to several hundred pages and multiple volumes. Depending on the complexity of the process and the level of detail included, each project will be unique to some degree. The design process for a project normally progresses from preliminary conceptual phases through to a final detailed design. The criteria used for the initial concepts are generally developed from rough data and preliminary testwork on the ore in question. Regardless, the plant throughput and products are defined, thus giving a scope and definition to the study phase. In some studies a range of throughputs may be analyzed in order to arrive at the most economically attractive size for the proposed operation. This optimum size is then used as the design throughput for the more detailed design phases. Similarly as more testwork results are available and the ore characteristics and process become more well defined a continuous updating of the design criteria is undertaken.

Jan 1, 1986

What is the real value of your data?Given that the cost of collecting and analysing an individual sample is always rising, it is important to understand the true value of a sample and that you are confident that you receive good value for your exploration dollar. Unfortunately too many samples are still collected today that will end up as worthless data; a liability to those who own it and a hindrance to finding that ore body.

Jan 1, 1986

By A. S. Malicsi, I. Iwasaki

The removal of hydrophobic coatings of flotation collectors from iron ores becomes of interest when a duplex flotation process is considered for upgrading, when a pelletizing process is considered for a concentrate floated with a fatty acid or a soap collector, or when a disposal of froth products from cationic silica flotation is of environmental concern. Ozone can oxidize organic compounds rapidly, thereby removing the hydrophobic coatings of flotation collectors. Ozone is widely used for treating and purifying drinking water, waste water treatment, and for chemicals processing (Murphy and Orr, 1975; Rice et al., 1980). Its uses in metallurgical operations, however, are very sparse (Allegrini et al., 1970; Chernobrov and Rozinoyer, 1975; Ishii et al., 1970; Iwasaki and Malicsi, 1985; Matsubara et al., 1978). Yet, its high reactivity and the absence of potentially hazardous byproducts become of interest in destroying flotation reagents adsorbed on mineral surfaces or remaining in mill water for recycle or for discharge. Duplex Flotation A duplex flotation process, as applied to oxidized iron ores, would involve a fatty acid flotation of iron minerals followed by an amine flotation of the siliceous gangue from the rougher iron concentrate. Such a process has been used in the Florida phosphate fields. Fatty acid coatings cannot be removed as readily with a simple acid or alkali treatment from iron oxide surfaces as from Florida phosphates. A combination of reagents, such as lime and quebracho, lime and alkali phosphate, or sulfuric acid and oxalic acid, has therefore been proposed. In a previous article (Iwasaki et al., 1967) , the use of activated carbon was found to be effective in removing fatty acid coatings both in the duplex flotation and the pelletizing processes. The use of ozone offers another approach to the removal of fatty acid coatings from iron oxide surfaces. To investigate the possible application of the duplex flotation process, a specularite ore from Michigan analyzing 36.5% iron was used. A 600-g (1.3-1b) sample was ground in a laboratory rod mill together with 250 g/t (0.5 lb per st) of sodium silicate to -150 µm (-100 mesh). This was transferred to a Fagergren laboratory flotation cell, and deslimed four times at 20 µm (quartz equivalent). The deslimed pulp was transferred to a laboratory conditioner, diluted to 40% solids, and conditioned with 250 g/t (0.5 lb per st) of soda ash and 250 g/t (0.5 lb per st) of oleic acid. The conditioned pulp was then transferred back to the Fagergren cell, floated until barren of froth, and the rougher froth product was returned to the cell and cleaned. The results are presented in Table 1. The cleaner concentrate at this point analyzed 45.3% Fe. The cleaner concentrate coated with fatty acid was transferred to a 2-L (0.53-gal) beaker. While the pulp was agitated with a glass T-stirrer, ozone was bubbled into the agitated pulp for 15 minutes at a rate of 10 mg/min (0.00035 oz per min) ozone (250 g/t or 0.5 lb per st 03 feed). It was observed that the pulp ceased to froth after about 10 minutes. The amine flotation of siliceous gangue from the ozonated pulp was carried out first by conditioning with a dextrin, a commonly used starch depressant for iron oxides. This was followed by flotation with a stage addition of an ether amine at increments of 100 g/t (0.2 lb per st). Three stages were required to float the siliceous gangue to near completion. The three froth products were combined and cleaned twice. When the cationic flotation Rougher, Cleaner 1 and Cleaner 2 cell products were combined, an iron concentrate analyzing 64.5% iron was obtained at an overall iron recovery of 72.8%. Pelletizing Fatty acid flotation concentrates have been pelletized successfully in northern Michigan mills. But at other locations, fatty acid coatings on iron flotation concentrates proved so undesirable in agglomeration that other methods of concentration had to be sought. For example, a sinter mix containing iron ore concentrates upgraded by fatty acid flotation resulted in decreased productivity. This occurred because the micropellets of particles with the hydrophobic coating are less tolerant of moisture. Thus, the bed permeability is lost (Beebe, 1965). The agglomeration of concentrates obtained by the fatty acid flotation alone, and the hydrophobic coatings destroyed by ozonation or by the duplex flotation process, is not expected to cause any difficulty since the surfaces of the concentrates would be hydrophilic. Removal of the fatty acid coating with activated carbon, indicated by the loss of floatability, was shown to restore the decrepitation temperature of wet balls during drying cycle (Iwasaki et al., 1967). Disposal of Cationic Silica Flotation Froths Recent demands of iron blast furnaces place the silica content of the magnetic taconite pellets at about 5%. Conventional process for magnetic taconite involving fine grinding and magnetic separation often produces magnetic concentrates analyzing in excess of 5% silica. This is due to the presence of the middling grains of siliceous gangue and magnetite. Cationic silica flotation of magnetic taconite concentrates (DeVaney, 1949) may be used to reduce the silica content. But the amine coating on siliceous gangue becomes of environmental concern when the flotation tailings are discarded in tailing ponds.

Jan 1, 1986

By D. L. Kiser

Conventional and advanced coal preparation technologies were investigated through both a literature search and through direct contact with investigators and developers. In addition to a brief description of each process, performance characteristics including feedstock type, ash and sulfur reduction, thermal energy recovery and cost are provided in a tabular form. Seven of the most commonly utilized conventional coal preparation processes, including those respectively accepting coarse, intermediate and fine coal feed, were reviewed. It was found that certain properly implemented and well maintained conventional processes were capable of better than 75 percent ash removal while recovering 90 percent or more of the inherent thermal energy. Almost 50 advanced coal preparation processes were investigated based on biological, chemical and physical principles. Physical processes investigated included cycloning, homogeneous heavy media, electrostatic, high gradient magnetic, flotation and selective coalescence. Using pulverized coal as a feedstock, some of these processes are respectively reported to be capable of removing better than 95 percent ash. 95 percent pyritic sulfur, and 50 percent organic sulfur while incurring energy losses of less than 5 percent.

Jan 1, 1986

By L. W. Saperstein, J. C. Mills, L. B. Phelps

Selective placement of toxic mine spoil has been advocated as a means of reducing environ¬mental pollution at the source. However, methods of burial to control environmental damage are not well understood. Using the finite element method, this paper investigates the burial of toxic material within low permeability packages below the water table. The effects of differing package and spoil permeabilities, anisotropy, and infiltration are modeled to provide information about their effect on the flow system. Projections can then be made that will assist in the design of the toxic spoil package to limit the amount of ground water flowing through them.

Jan 1, 1986

By R. Karl Zipf, Z. T. Bieniawski

Based on the premise that understanding the fundamental mechanics of fine fragment formation in coal will lead to reducing coal dust problems in mines, a thorough study of the mechanics of crack propagation in coal was undertaken. Two approaches were considered in an attempt to understand and quantify the fracture process as it relates to fine fragment formation. In one approach, theoretical models are used which describe the size of the fracture process zone which may relate to the amount of structural damage and fine fragment formation on the new crack surface. The other approach is based on the relationship between crack tip stress intensity and new surface appearance for mixed mode crack propagation. Preliminary observations with a scanning electron microscope support the premise that fine fragment formation is related to fracture surface appearance and fracture initiation conditions. An experimental program designed to supply the input parameters for these approaches is presently underway. The experimentation features mixed mode fracture toughness testing, using a special mixed mode testing rig, and fracture velocity measurements with a crack propagation gage. The interpretation of this data via the approaches discussed will provide further under- standing of the mechanics of fine fragment formation in coal.

Jan 1, 1986

By J. M. Richardson, A. L. Mular

Metallurgical balances are fundamental to the successful design and operation of concentration and dewatering circuits. With computerized balance techniques gaining prominence in recent years, it is essential that engineers understand the basic principles that underlie the new methods, as well as the various applications for design of new plants and analysis of existing operations. This chapter discusses two important types of metallurgical balance: (1) steady-state design (2) operating data adjustment Application of computerized steady- state design balancing is demonstrated through the example of a typical copper concentrator flowsheet. Operating data adjustment to achieve a consistent balance is demonstrated for a typical concentrator operation.

Jan 1, 1986

By Kevin Hegerle

The Henderson Mill has operated over a wide range of production rates, feed grades, manpower levels and recovery targets since start-up in 1976. Henderson Mill personnel, both management and hourly, have successfully responded to these changes by not only maintaining unit costs, but by actually decreasing unit costs. Methods of cost reduction have included conventional austerity programs, innovative technological improvements and creative work schedules. This paper addresses both maintenance and operating cost reductions and efficiency improvements.

Jan 1, 1986

Australia is a leading producer of mineral sands and according to U.S. Bureau of Mines, produced 24, 53 and 64% of world's production of ilmenite, rutile and zircon respectively in 1983. The industry which is mainly export oriented earned in export income about $210 million in 1985. The dominant position which Australia occupies in world produc- tion of mineral sands is also maintained in many areas of research and development work on the processing and application of these minerals. Some of this research which is leading the world has been responsible for setting up industries to produce value-added and high-tech products such as synthetic rutile and partially stabilized zirconia (PSZ). The production of high purity zirconia is due to commence shortly while research in rare earths offers an exciting prospect for future Developments.

Jan 1, 1986

By R. L. Peyton

Risk analysis is used extensively in many engineering applications. Although its use in the field of dam safety has been limited in practice, it has received considerable attention in recent years in the dam safety literature. Thus far, it has been shown that risk analysis in the evaluation of existing dams has the potential for providing a more rational basis for decision- making because of its focus on the direct issues--likelihood of failure, likelihood of loss of life, and risk cost of damages. It provides for a logical balance between the risk a dam imposes and the degree to which rehabilitation is required, compared to traditional evaluations based on somewhat arbitrarily chosen design events applied to large classes of dams. Dam owners could benefit by optimizing the cost of remedial measures. Downstream landowners could benefit by minimizing the likelihood of flood damages. However, it is also clear that significant technical and policy issues remain to be resolved before risk analysis in dam safety is accepted and routinely implemented in engineering practice. An obvious and important potential application of risk analysis is its use by the state regulatory agency as an in-house evaluation tool, or even as part of regulatory policy, in the implementation of its state dam safety program. Adoption of such a policy would have an important impact on the mining industry. .Although no state dam safety programs are known by the writers to have officially incorporated risk analysis into their regulations, there appears to be considerable interest in the concept. In recent surveys 47 states agreed that the development and promotion of a risk assessment methodology for state dam safety programs should be encouraged (Tschantz, 1983; Tschantz, 1984). The issue has also received important attention within the Association of State Dam Safety Officials (1986). One state-Illinois-proposed regulations during 1986 to allow risk analysis to justify lower spillway requirements for existing dams (Illinois Department of Transportation, 1986). At the Federal level, the National Research Council has found risk analysis especially appropriate for assessing dam safety at high-hazard dams (National Research Council, 19851, the Bureau of Reclamation has published guidelines for incorporating risk analysis into their dam safety grogram (U.S. Department of the Interior, 1986), and the Federal Emergency Management Agency has recently sponsored workshops and supported research related to risk analysis in dam safety (Federal Emergency Management Agency, 1985a ; Federal Emergency Management Agency, 1985b; - - McCann, et. al., 1985a, 1985b).

Jan 1, 1986

By F. F. Aplan, E. C. Dowling, R. R. Klimpel

Numerous flotation models have been proposed in the literature. Thirteen of these have been applied to batch flotation data and evaluated with respect to one another using statistical techniques. Flotation tests were carried out on samples of a US porphyry copper ore (Pinto Valley, AZ). The ore was tested using various collector and frother systems to produce different time-recovery profiles. These were used to calculate flotation rate and ultimate recovery parameters for each model. The models were then evaluated statistically to determine the overall fit of the calculated to the observed data and to test the range of significance of the parameters in each model.

Jan 1, 1986

By E. F. Evoy

"The Gunnar uranium deposit was within metasedimentary rocks of the late Archaen Tazin Group. These rocks were intensely altered by albitization so that the immediate host to the ore consisted dominantly of albite, and by the subsequent introduction of calcite. The ore consisted of disseminated pitchblende and uranophane in a pipe-shaped breccia zone. Oxidation of the ore was more intense near surface than at depth, but there was no near-surface enrichment.IntroductionThe Gunnar Mine site is on the tip of Crackingstone Peninsula, on the north shore of Lake Athabasca, Province of Saskatchewan, Canada. The peninsula forms the southern part of the Beaverlodge mining area. The ore consisted of disseminated pitchblende and uranophane in brecciated metasedimentary rocks of the Tazin Group, and the deposit was characterized by extreme albitization and subsequent carbonatization of the host environment.Production from the mine began in 1954 and the ore was depleted by 1963. In that interval the deposit yielded about 5 million tonnes of ore containing about I. 75 kg/tonne U3O8. It was mined initially from an open-pit and subsequently from underground; the open-pit contributed about 55% of total tonnage. Uranium was recovered by atmospheric leaching in sulphuric acid, ion exchange concentration, and precipitation with magnesia.This paper is based on studies made during the productive life of the mine and is concerned primarily with pre-ore alteration of the rocks containing the deposit, and with the ore mineralogy."

Jan 1, 1986