Search Documents

By M. J. Waller

Surface resistivity techniques were used at four field sites to monitor changes in apparent resistivities with variations in soil moisture content in the vadose zone. Apparent resistivity values were correlated with gravimetric moisture contents from soil samples taken at each site. Tensiometer readings were taken at two sites and correlated with the results of gravimetric moisture contents and apparent resistivities. Moisture at two of the sites was added by extensive watering; rainfall events were monitored at the other two sites. A recharge event at a dewatering program was monitored at a fifth site. A Ghosh-Koefed multi-layer computing algorithm was used to derive true resistivities from bulk or apparent resistivities. An automated data acquisition system was developed to measure resistivity changes and to process the data in the field. These studies are the first to evaluate measurement of moisture migration in clay rich soils using surface resistivity techniques. Results indicate that surface resistivity techniques readily measure changes in moisture contents in the vadose zone in clay rich soils. Correlation of apparent and true resistivity values with gravimetric moisture contents is more complex and requires additional research.

Jan 1, 1986

By F. Hampshire

"IntroductionThis paper is intended to cover questions raised by operating staff at various installations and is not intended to give comprehensive coverage of power plant and power system design. The paper is concerned mainly with the electrics , although a brief section gives the reasons for selection of diesels rather than other prime movers.The material is not new but brings out points which seem to be raised regularly during the design , commissioning and operation o f a new plant. Diesels versus other Prime MoversDiesel-electric plant for the mining industry falls into two major categories -emergency power and prim e power.1) Emergency power (for use only when the regular utility supply has failed) requires reliable starting and operation and reasonable first cost. Fuel economy and maintenance are of little importance as the machine(s) generate few kilowatt hours only. The diesel's competition in this field is the gas turbine, however diesels are more widely used than gas turbines in this application.2) Prime power is a different situation as the bottom line of total cost is highly affected by fuel costs.In general , mines which are within reasonable transmission distance of an existing utility find the lowest net cost result s from hooking up to the utility. If a min e is remote from an electric utility then the possible alternatives are:a) Hydro- electric power if there is a site capable of development at reasonable cost including the cost of transmission facilities. Such sites are not common, but brief and inexpensive considerationof this possibility is warranted .b) Diesel power with consideration of different grades of fuel.c) Thermal (steam) power generation from coal or oil.d) Gas turbines.In addition to the above there is the possibility of wind power (as a supplementary source) and a number of technologies which may become feasible in the future (e.g. small nuclear plants, fuel cells). For obvious reasons, small isolated generating systems required for remote mines, tend to lean to conservative technology.Among the fossil fuel plants, the diesel enjoys advantage on over-all costs as summarized in Table 1."

Jan 1, 1986

By Albert W. Deurbrouck

The coal reserves in the United States are estimated to be in excess of 300 billion recoverable tons, and current projections of energy requirements indicate our increased dependence upon these reserves. The Department of Energy's Energy Outlook for 1984 projects that coal consumption in the United States will increase from 737 million tons in 1983 to 958 million tons in 1990, and then to 1,110 million tons in 1995 (Table 1). As shown in this table, the future utilization of coal in the United States is closely tied to the electric utility market, a market that consumes about 85% of the coal produced. Be- cause of this dependence on the utility market, the uncertainties of new environmental regulations, particularly those concerning sulfur emissions, could have a significant adverse impact on future coal demands in the United States. SULFUR IN U.S. COALS Most of the Nation's coal reserves contain too much sulfur to be fired directly and meet existing emission control standards. In Table 2, the sulfur contents of the coals of the eastern United States are summarized by sulfur levels according to regions. While the coals of some of the eastern regions are predominantly high in sulfur content, it is important to recognize that large tonnages of coal with relatively lower sulfur content are available in these regions. Furthermore, an often significant portion of the sulfur occurs in the form of iron sulfide (Fes2 or pyrite). Because pyrite occurs as discrete particles of high specific gravity, it can often be removed by simple, inexpensive physical coal beneficiation techniques after being liberated by stage crushing. The potential for physical removal of pyrite by conventional specific gravity processes combined with stage crushing is summarized in Table 3 on a regional basis.

Jan 1, 1986

Two ends of a longwall face are not only concentrated locations of equipment, but also provide ventilation and access. The roof strata stability here has an important influence on mining coal and safety. Based on field obser- vations in the gateways at Zaozhuang Colliery (Shandong Province) and model tests, the author developed a structural model of the overlying strata at the ends of the longwall face - the arc triangular cantilever plate - to which the elastic theory of plates can be applied. Factors influencing the stability of the cantilever plate and its breaking character- istics are discussed. Requirements and design parameters for supports at face ends are pro- posed, based on these factors.

Jan 1, 1986

By David E. Nicholas, Steven R. Dismuke, Paul F. Cicchini

The Buick mine, located 195 kilometers (120 miles) southwest of St. Louis in the Viburnum Trend, is owned and operated by Homestake Mining Company. The mine produces lead and zinc ore from a room and pillar mining method at a depth of approximately 335 m (1 100 ft). The Buick orebody typically averages 60 to 120 m (200 to 400 ft) in width with ore thicknesses ranging from 2.4 to 36.6 m (8 to 120 ft). The mine is divided in two; the halves are referred to as the North mine and South mine orebodies. The North mine orebody contains the higher grade ore; however, the developed reserves for the South mine orebody comprise about 60 percent of the total developed reserves for the Buick property. Existing pillars represent one-third of the total developed reserves.

Jan 1, 1986

By Richard J. Mainiero, Michael S. Wieland, Harry C. Verakis

The Bureau of Mines, U.S. Department of the Interior, has been conducting research on delay blasting in underground coal mines in support of the efforts of Mine Safety and Health Administration (MSHA), U.S. Department of Labor, to revise coal mine blasting regulations. Part of the research centered on developing an understanding of the factors that lead to misfires of permissible explosives. Research was conducted to determine whether frequency of misfires was related to borehole spacing. For a wide variety of permissible explosives, misfires were observed for about 50 X of the holes at 45-cm (18-in) spacing. Misfires were also observed for 60-cm (24-in) spacing, but the frequency of misfires was much lower than observed for the 45-cm (18-in) spacing. The Bureau has recommended that hole spacings of less than 60 cm (24 in) be prohibited.

Jan 1, 1986

By C. E. Jordan

The fundamental characteristics of ultrafine chalcopyrite flotation were investigated by the Bureau of Mines to establish techniques to improve recovery of ultrafine chalcopyrite. Intense agitation during conditioning was found to improve flotation recovery of the ultrafine chalcopyrite. A split-circuit flotation design, treating the plus 38-µm-size ore by the conventional method and treating the minus 38-µm-size ore with intense agitation conditioning followed by flotation, recovered 95.6 pct of the copper in a 28.3-pct-copper concentrate, This was a 5-pct increase in copper recovery over the conventional chalcopyrite flotation method.

Jan 1, 1986

By Scott IR

In stratigraphic orebodies, estimation of footwall and hangingwall location is often of more importance than grade estimation. Contoured grade estimates often produce smeared boundaries and the use of accumulations and thicknesses as variables re-introduces the original problem: location of the point at which the estimate is to be made. The paper introduces statistical and geostatistical techniques for the solution of the problem and illustrates the techniques with a case study from Mount Isa, one of the world's largest producing silver-lead-zinc deposits. Solutions for calculating variograms in orebodies of variable dip, strike and plunge are presented together with relative variograms for individual metals, metal accumulation and orebody thickness. Optimal methods for hangingwall and footwall location are introduced and illustrated with an example. Orebody boundaries are then kriged after which individual metal grades are kriged within the estimated boundaries. The boundary estimates are compared with manually interpreted boundaries and known boundaries in mined-out areas. Grade and tonnage estimates are compared in mined-out areas.

Jan 1, 1986

By James P. Bennett

The Bureau of Mines is investigating the acid resistance of ceramic materials to identify construction materials for emerging technology in chemical and metallurgical processes. Eight commercial ceramic materials, were evaluated: two red shale, two fireclay, one silicon carbide, one silica, one carbon, and one high-alumina. Samples were exposed to 10 wt pct H2S04 at 50° C and 10, 30, 50, 70, and 90 wt pct H2S04 at 90° C for time periods of 110 days. Statistically significant changes in cold crushing strength were observed in the silicon carbide and car-bon materials. Weight changes and the leach rate of Al, Ca. Fe. K, Mg, Na. Si, and Ti were also monitored. The most severe corrosion conditions were at 90° C and 30 to 50 wt pct H2S04 for the acidproof and at 10 wt pct H2S04 for the acid-resistant materials. The silica and the high-alumina materials were the most acid-resistant, followed by the higher density red shale and fireclay.

Jan 1, 1986

"?irovski Vrh" Uranium deposit in Slovenia is type of mineralized sediments in ore bearing belts of deflected S-structure, in which the belt is less than 25% mineralized. Ore bodies of irregular small thickness, unreliably contoured, made difficult estimation of correct contours, which are necessary for design and exploitation works. The deposit was explored by vertical boreholes made at the surface and by boreholes fanned from drives. For the purpose of application of this estimation method, 1 m composites have been made in slices which were parallel to the referential belt plane. Estimation was made for 1,5m x 1,5m x lm blocks which do correspond to the size of the containers in the ore transport stage. Two variables have been used: the first, indicator of function (ore=1, waste material =0) and kriging method; the second, logarithmical content of Uranium and Minimum Mean Square Error Estimation (MMSEE) method. Based on estimated values of those variables, probability of ore quantity as well as Uranium content over determined cut-off were calculated for each block. Those two parameters enable determination of the most probable form of the ore body in ecah one metter slice. Estimation of sixteen small blocks in a large 1,5m x 1,5m x 1m block made possible estimation of ore quantity and its content for the determined cut-off, as well as categorization of exploration. This method is being used for estimation of ore reserves and planning of exploration operations. The described' methodology was tested in an exploitation block.

Jan 1, 1986

By D. A. Sangrey, D. Marcus, S. A. Miller

A methodology was developed wherein the increase in compressive strength, mineralogical changes, and pore water composition were studied simultaneously as a function of moisturized spent shale curing time. From these results the relationship between the nature of cementation process and the composition of pore water was established. Heavy metals were entrapped in the cementing constituents and the pore water became mainly a solution of alkaline sulfates. The specific data are applicable only to the material studied. But the methodology and general conclusions are useful for evaluating the environmental factors in spent shale disposal and expected leachates composition.

Jan 1, 1986

By W. Nazarewicz

The introduction of continuous papermaking in the early 1800's was the beginning of the industry as we know it today. Since that time, the majority of the paper produced has employed an acid process. However, in the mid 1960?s, European producers began a transition to an alkaline papermaking process. Early European mill conversions to alkaline papermaking begun in the 601s, accelerated during the 1970's influenced by the dramatically higher cost for OPEC energy as well as the high cost of fiber and imported filler clay.

Jan 1, 1986

By M. E. Karabin, R. J. O'Malley

"A mathematical model of the roll casting process has been developed which predicts macro-variables, such as roll separating force, roll torque, and strip exit speed for a range of roll speeds. Continuum variables, such as interface pressure, interface shear stress, freeze-front shape, and internal temperature distribution are also predicted.The model consists of two independent segments: solidification and rolling. The solidification model is two-dimensional (thickness and rolling direction) and is capable of handling alloy solidification. The solidification model is employed until solidification through the thickness is complete, then the rolling solution is activated.The rolling model is a one-dimensional (rolling direction) mechanical solution based on the von Karman approach, coupled with a two-dimensional thermal solution. The flow stress is expressed as a function of the average through-thickness temperature of the strip.Experiments were performed using a laboratory roll caster to test and refine the model. Experimental strip exit temperatures were used as input to the model. Experimental and predicted roll torque and strip exit speea were forced into agreement at a single reference roll speed to obtain values for the coefficient of friction and the interfacial heat transfer coefficient. Using these values, good agreement was obtained between predicted and experimental torque and strip exit speed over the entire range of roll speeds examined."

Jan 1, 1986

By Robert J. Rothwell

Underground mining of coal by longwall mining methods has not been a predominant technique in Ohio. To date, only five mines in the state utilize this method, however, the technique has sparked a certain amount of controversy. As a mining technique, longwalling was introduced into southeastern Ohio in the early 1970's but it did not attract public attention until the mines began moving into privately held surface lands. This occurred coincidentally at about the same time that the state of Ohio began to regulate the environmental impacts of underground mining. Prior to the passage of the Surface Mining Control and Reclamation Act in 1977, (SMCRA), Ohio's reclamation law, Chapter 1513 Ohio Revised Code (O.R.C. 1513) did not regulate underground coal mines. As a result of SMCRA, the Ohio Statute was amended in 1978, to include regulation of the surface effects of subsidence. The inevitable result was that existing mines were immediately subject to regulations that were not considered during the initial mine planning process. (For an excellent survey of Ohio Laws that deal with coal mine subsidence, see Zima, 1985. ) The problem faced at that time by both the coal industry and the Ohio Division of Reclamation (the agency within ODNR charged with implementing O.R.C. Ch. 1513.1, was that of attempting to superimpose permitting requirements, and design performance standards onto mines that' had been operational for a number of years.

Jan 1, 1986

By C. Trepka-Bloch

Silver-copper-zinc mineralization is confined to metasomatically altered late Paleozoic and Cretaceous sediments consisting predominantly of limestone, siltstone and sandstone units. Mineralized alteration halos are spatially and presumably also genetically related to the emplacement of a Cretaceous quartz monzonite stock. Several generations of ore formation and alteration took place. Distribution of skarn and ore was influenced by intrusive contacts, calcareous horizons and by relatively less permeable rock units which served as barriers. Most of the ore bodies form conformable near horizontal mantos but some follow steeply dipping monzonite dikes. Structurally controlled alteration pipes connect the mantos locally. The deposit is strongly affected by mineralized fault and breccia zones.

Jan 1, 1986

By M. S. Azun

M.S. Azun I have many objections to the content of the author's paper. Before discussing it, however, I would like to repeat the property of semivariogram function. Second order stationary properties of regionalized variables (ReV's) such as semivariogram function ?(h) are perfectly known in geostatistics. Also, the kriging equations in the language of mathematical statistics using second order stationary properties are well understood. However, the way to use the sample (estimated) semivariogram function in any one of the kriging procedures is vague. The sample semivariogram function is given as follows: [1 N-hy*(h) = 2(N h) i21 {Xi-Xi+h}Z, h=0, 1, N-1] where N is the total number of samples, Xi is the sample value at the i - th location, X i+h is the sample value at the i +h - th location, and h is the distance among the samples. An estimation variance of sample semivariogram function of first lag is smaller than that of higher order lag. The theoretical semivariogram function reaches the variance of samples asymptotically. But this is not easily observable because of the larger variation involved in the estimate of semivariogram function. In general, an estimation procedure is done for h = 0, 1, 2,…., up to the greatest integer less than N/2, even though sample semivariogram function can be computable through N-1. After estimating semivariogram function, the critical question of how to model sample semivariogram function arises. As seen in the above equation, sample semivariogram function is discrete and can be smoothed by the model being selected. Therefore, modeling of sample semivariogram function is the most important step in geostatistics. It not only smoothes a discrete function but also affects the results of the kriging procedure. When the only aim is to model the semivariogram function, which is the basic point of the author's paper, one can employ any fitting techniques, such as curve fitting, or any ar¬bitrary functions, which are called submodels in the paper. The term "arbitrary function" is used rather than "submodel" because there is no basic understanding of developing them. The author suggests that the sum of those submodels can also be used for the modeling of sample semivariogram function. The combination of any arbitrary functions brings many problems instead of giving an insight of the domain structure considered. The author used two arbitrary functions and the nugget effect in response to sample semivariogram function (Fig. 10). For the same example, he stated that the parameters involved in the mixed arbitrary function model can be accepted when the discrepancy between sample semivariogram function and the model is small visually. For verifying the fitting behavior of any selected model, one should not be contented with the visual satisfactory. Some statistical measure such as goodness of fit has to be used. The author's practice is no more than an exercise in curve fitting without any fundamental understanding or conceptualization of the underlying physical mechanism. Furthermore, the selection of any model is not an easy task if the purpose is the search for the "best" response to the observed second order properties of ReV's. I suggest that the Markovian model (Azun, 1983), on the basis of a theoretical understanding of underlying mechanism, which gives more information about the occurrence of regionalized variables, is used to respond all properties of ReV's. There are a lot of problems for modeling of onedimensional sample semivariogram function. Thus, it is not appropriate to go to higher order dimensional sample semivariogram function modeling. In the meantime, I would recommend that one can connect the values of standardized sample semivariogram function rather than simple values of semivariogram function in the two-dimensional estimation. The standardized values can be computed in dividing the semivariogram function value by the number of sample pairs involved in each lag regardless of the directions. In conclusion, geostatistics is an interdisciplinary area in mining that uses the principles of mathematical statistics. Thus, it should not violate any probabilistic and statistical rules. When Matheron was developing the theory of geostatistical study in the early years of geostatistics, many mining people had a reservation accepting the geostatistical tools. However, this does not mean that we, the geostatisticians, might try to convince those people using some "strange" tools or rules as some authors implied (Baafi and Kim, 1984). Instead, we have to develop and explain the geostatistical tools staying only in the framework of statistical concepts and properties. ? References Azun, M.S., 1983, "Stochastic Process Modeling of Spatially Distributed Geostatistical Data," Columbia University, Ph.D. Thesis. Baafi, E.Y., and Kim, Y.C., 1984, "Discussion - Comparison of Different Ore Reserve Estimation Methods Using Conditional Simulation," Mining Engineering, Vol. 36, No. 3, p. 280. Reply by J.M. Rendu The interactive method proposed by Rendu allows practitioners to develop semivariogram models that take into account not only the numerical information obtained by sampling, but also highly significant additional information that often cannot be quantified. The geology of the deposit - including hypotheses concerning its genesis, sampling methods, assaying methods, and mathematical methods used to calculate the semivariograms - all have an influence on the numerical results obtained and on how these results should be interpreted. If all the information concerning the spatial distribution of values in a mineral deposit was contained in the sample values, it could be argued that statistical techniques alone would produce optimum models. However, this is rarely, if ever, the case. Methods that allow the user to take into account his experience and his geologic understanding of the deposit should not be rejected for the sake of theoretical statistical purity. ?

Jan 1, 1986

By K. P. Chong

Introduction One of the requirements of processing oil shale or other energy bearing rocks is to optimize particle sizes and permeability distributions in fragmentations as indicated by Hommert (1984). Basic to the understanding and planning of in situ fragmentation and ex situ mining of oil shale are the mechanical properties. During the past six years, an innovative and unique program was established by Chong et al. (1979, 1980a, 1980b, 1982a, 1982b) that developed an efficient methodology for standardized and simplified mechanical testing of the western oil shale. The experiments include precise, representative, and duplicable sample preparation; uniaxial static compression testing; "modified" split cylinder testing; uniaxial creep and relaxation testing under extended periods of time; dynamic testing with varying strain rates; and 3-D constitutive relationships. However, as far as the fracture mechanics is concerned, as Edl (1980) pointed out, there is still a lack of understanding "of the fundamental explosive rock breakage mechanisms," which "has necessitated extensive reliance on very costly empirical approaches." Fracture mechanics of rocks and oil shale (Costin, 1981; Schmidt, 1977; Abou-Sayed, 1977; and Barker, 1977) has been based on conventional fracture mechanics using regular notched samples with limited variations of oil yields and assuming the material to be isotropic and elastic (Kobayashi, 1975; Caddell, 1980). A cylindrical double cantilever beam (DCB) specimen with a "V" slot, known as a short rod specimen, has been used by Barker (1977) to determine fracture toughness of rock materials. The inherent geometric stability of the reinforced DCB specimen makes it suitable to be used with all brittle materials. Due to its remarkable stability for the initial crack growth, the DCB specimen can be used for dynamic fracture toughness testing as well. This specimen is more suitable for the evaluation of fracture toughness at high strain rates than most other fracture specimens. However, Barker's DCB specimen is not very well adaptable for short cores or layered rocks since the specimen contains numerous layers (say in a 100-mm (4-in.) long specimen), and the rock properties change from layer to layer. Schmidt (1977) studied the fracture mechanics of oil shale with two oil yields, using notched beams. Using several independent established testing methods, Costin (1981) pioneered the investigation of the static

Jan 1, 1986

Technological advances evolve in different ways; many are the result of years of application of scientific method. i.e. Observation Deduction Hypothesis Proof In the mining industry, better explosives, drill bits or reagents are likely to evolve in this way. The scientific method is suited to the application of conventional management structures. Other advances are simply the result of a "brainstorm", or building a better mousetrap. Such inspiration probably resulted in "Split Set" rock bolts, or the first use of a vacuum cleaner principle for shaft mucking. Individual consultants can apply lateral thinking to generate such inspiration. In gathering material for the presentation of this paper, I sent a.letter to all members of the Mineral Industry Consultants Association asking them to nominate problems in the industry requiring investigation. The answers have been divided into two classifications - contract research underway and identified problems requiring solutions.

Jan 1, 1986

By Tim J. Carew, Dennis C. Martin

"One approach to stabilization of rock slopes is to place a buttress at the toe of the slope to provide additional resisting forces and increase the length and strength properties along the failure surface. This paper describes the rock mechanics and mine planning aspects of incorporating a buttress of intact rock in the lower part of the slope as part of the slope design for the south wall of the final pit at Cassiar Mine. Stability analysis techniques and results are described. Analyses results have indicated that, in order to maintain steep over-all slopes in the final pit, a buttress of intact rock shoud be incorporated into the lower section of the slope until late in mine life. The effect of the buttress is to flatten the slope and reduce the slope height thereby improving slope stability. The mining plans would be such that the buttress would be mined out during the last four months of mining when the consequences of instability would be least severe.IntroductionThe concept of using a buttress to stabilize slopes has been used in mining and civil engineering construction in may locations (Richards and Stimpson, 1977). Most buttresses involve placement of coarse rock fill timber cribs or other material as a load at the toe of an already unstable slope to provide forces which resist failure by counteracting driving forces and increasing the length and strength of the failure path.This paper describes the geotechnical and mine planning aspects of incorporating a buttress of intact rock in the design of the south wall of Cassiar Mine. The effect of an intact rock buttress is to flatten the slope and reduce the slope height, thereby improving slope stability. No actual construction is required other than normal excavation of the slope. The ""mine plans would be such that the buttress would be mined out at the end of mine life when the impact of instability would be less severe and additional ore might possibly be recovered from the slopes. Mining of the buttress could induce instability at the very end of mine life at a time when maximum ore extraction has been achieved."

Jan 1, 1986

By W. G. Prast

Best known for its extensive bauxite and alumina exports, Jamaica also has a small but active industrial minerals sector. The island has for many years been a net exporter of small tonnages of gypsum, metallurgical-grade limestone and marble products. As bauxite and alumina earnings have declined the government of Jamaica has made extra efforts to promote growth of overseas sales of these nonmetallics. The nearby U.S. market is a natural first choice for new exports. Overview In 1984, Jamaica quarried an estimated 3.2 million cu m of marble and fill and an additional 3.5 million cu m of sand and gravel, for use in domestic construction. These amounts are in line with the production in earlier years of the 1980s but are not a factor in the export pattern and need not be considered further. Similarly, annual production of 15 million ton of silica sand for the manufacture of glass bottles is principally consumed by the domestic market.

Jan 1, 1986