Search Documents

As near surface deposits are increasingly mined out and pit widths beginto exceed the reach of practical direct-casting stripping machines, high haulage costs can make truck-shovel pre-stripping operations uneconomic. This is compounded because the rate of inflation for diesel fuel oil, lubricants, tyres, etc. exceeds the general rate of inflation. The use of conveyor transport systems, long established in terracemining operations in weak materials, e.g. engineering soils, can provide a viable haulage alternative in pre-strip operations and in some open pit settings. The paper describes the engineering requirements and basic economics of such systems.

Jan 1, 1985

By Rudolf Voigt

Lignite reserves occur all over the world in different climatic regions. This means, that the impact of the hydrologic regime upon mining activities and, vice versa, of the mining activities upon ground and surface water conditions will be different between any two mines. On the other hand, most economically important lignite deposits can be grouped according to principal depositional and structural features described briefly in the following section. These features do allow a preliminary assessments of the nature of ground water problems which may face the mine. The cost of protection against water which threatens a mine, the environmental impact of the appropriate measures to achieve this end and the restraints of population density which both might exclude the most cost-effective approach will govern the project expenditure for drainage work. Whether or not this expenditure can be borne by the project must be established during the feasi¬bility phases of mine planning. So, the somewhat provoking title of this paper does not mean that its question can be answered once for ever. It should rather serve to bring to the attention of the audience the major features of mine water control.

Jan 1, 1985

By Charles R. Jenkins

Three sedimentation ponds had their performance evaluated before and after installation of modifications. Each pond had a floating baffle installed, two had siphon outlets and one had a floating outlet device. Baffles inhibited short circuiting, and the outlet devices retarded flow following a rainfall event, and drained the pond creating a large storage volume to maximize detention time. Total suspended solids and settleable solids tests were run on samples of influent and effluent to evaluate pond performance. Particle size analyses were run on samples containing measurable amounts of solids. Performance improved in each pond, with baffles providing the major improvement. Through the entire surface mining process un- protected soil is exposed to direct rainfall and subject to accelerated erosion. Without controls, receiving streams would be "choked" by the additional sediment load. Several states, including West Virginia, require that sediment control ponds be constructed to trap the sediment before the water enters receiving streams. Even well designed ponds have exhibited difficulty in meeting effluent limitations. In a study supported by EPA, about half the ponds did not meet effluent limitations (1). There is a critical need to reduce sediment losses using presediment pond controls or by improving sediment pond performance. The objectives of this study were to evaluate modifications designed to improve sediment pond performance by; 1) monitoring three ponds prior to modification, 2) install floating baffles and 3) modify the principle spillway and determine the change in pond performance.

Jan 1, 1985

By Benjamin W. Haynes

The Bureau of Mines conducted research to provide technical information needed to devise waste management plans for the processing of manganese nodules. Studies included summary descriptions of Pacific manganese nodules, process options and flowsheets, methods for characterizing nodules and their tailings, and results of analyses of laboratory and pilot-plant generated tailings. This information is the result of a cooperative research effort of the Bureau of Mines and the National Oceanic and Atmospheric Administration (NOAA), with NOAA providing funding and the Bureau conducting the research. A summary of the extensive literature review is provided for manganese nodule mineralogy, chemistry, processing techniques, and methods of analyses. Characterizations and analyses of laboratory-generated tailings and slags are given, as well as the results of the leaching studies on these waste materials. Leachability was determined by three standard leachate tests- the Environmental Protection Agency (EPA) extraction procedure (EP) toxicity test, the American Society for Testing and Materials shake extraction test, and the U.S. Army Corps of Engineers-EPA seawater elutriant test. While the wastes generated in the laboratory may not be entirely representative of those to be generated in full-scale plants, results of these studies provide a positive indication that commercial recovery of cobalt, copper, manganese, and nickel from manganese nodules would be environmentally acceptable.

Jan 1, 1985

By R. A. Matuszak

Historically most mine management teams have been forced to operate in a more or less subjective manner. The objectives of mine management are simple and clear. Like other operational managements, mine management teams have the traditional well defined goals of improving efficiency and production while decreasing costs. Unlike other operational managements however, mining teams deal regularly with a vast assortment of uncertainties caused by: - Key production tools being mobile and widely dispersed, and - Non-uniform mining conditions At best in most operations these conditions cause obstacles to productivity and at the same time cause long delay in managment awareness of the obstacles. Planning with delayed feedback of information about necessary deviations is incomplete planning. For these reasons increased operational efficiency remains a constant though somewhat elusive goal.

Jan 1, 1985

Western Mining Corporation began shaft sinking operations at it's Foster orebody, south of Kambalda, on the 20th June, 1984. The top levels of the orebody are currently being mined via a decline some 1.5km away.Long term plans require the shaft and decline to combine and produce 400,000 tonnes of nickel ore per annum. Eventually all of the ore produced will be hauled up the shaft.The shaft is 4.5m in diameter and the target depth is 760m. Ground conditions to date suggest there will be no further need for concrete lining beyond the oxidised zone. As such, the sink is an open-shaft development in competent basalt rock. Shaft furniture will be installed on completion of the excavation to the target depth.This paper summarises the experience in the project to date, along with comparisons to conventional shaft sinking methods employed in previous years at Kambalda Nickel Operations.

Jan 1, 1985

By A. Lloyd, Montgomery, J. Jorgesen, W. J.

"Coals are ranked according to their degree of metamorphism or progressive change in the natural series from lignite to anthracite. The reader is referred to ASTM Standard D-388, ""Standard Classification of Coals by Rank"" for a detailed description of the system in use throughout North America including Canada.Fixed carbon and calorific value (expressed in Btu/ lb) calculated to the mineral-matter-free basis have been chosen as the main characteristics from which rank is established. Higher rank coals are classified according to fixed carbon content, lower rank coals according to the calorific value on a ""moist"" mineral-matter-free basis. Certain adjacent groups are differentiated according to their agglomerating (caking) properties. ""Moist"" refers to inherent moisture. Referring to Table 1, coals having calorific values greater than 14,000 Btu/lb on a moist mineral-matter-free basis and fixed carbon of 69% or more on a dry mineral-matter-free basis are classified according to fixed carbon. Coals having calorific values of less than 14,000 Btu/lb on a moist mineralmatter-free basis are classified according to calorific value on a moist mineral-matter-free basis. Agglomerating coals having 69 to 86% fixed carbon on the dry mineral-matter-free basis are classified in the low or medium volatile group of the bituminous class according to their volatile matter content. Agglomerating coals having calorific values between 10,500 and 11,500 Btu/lb are classified in the high volatile C bituminous coal group; nonagglomerating coals in the same calorific value range are classified in the sub-bituminous A coal group."

Jan 1, 1985

By R. M. Campoy

Mexico's mineral wealth has long been recognised and indeed has played a historically significant role on a world scale. The dynamics of the Mexican mineral industry have experienced a dramatic transformation especially over the last two decades. This transformation has mainly been instigated by the high growth rates and industrialisation of the Mexican economy since the 1960's. This paper focuses on the base metals sector of the industry which represents one of the major contributors to this transformation. The objective is to present a brief base metals review and to discuss some recent occurrences which pertain to this sector of the industry. This is followed by a discussion of mining's relevance in the current economic situation in Mexico. With this overview as background, the investment climate, primarily from a domestic investor's perspective and secondly in terms of foreign investment, is discussed. Finally, some recent government initiatives, including tax and accounting changes, are outlined. Any one of the sections of this paper can easily be developed into an extensive and indepth analysis; however, the intention of this paper is to provide the reader with a broad overview of the topics discussed.

Jan 1, 1985

By James J. Broderick

In the production of Pig Iron - Limestone, Coke and Iron Ore pellets are changed to the blast furnace and reacted at approximately 2,800 degrees F. The resultant products are molten iron and a molten slag - not unlike lava. The molten slag stream is channeled into open pits, cooled with water, crushed and sized for various industrial applications. The production of steel from pig iron in open hearth, B0P, BOF and electric furnaces results in somewhat similar slags: but since free lime is normally the flux, the resultant slags are not satisfactory for use in cement pastes. When exposed to water, the lime slakes, expands by 250% and ruptures the concrete. Thus, the slag discussed first is Blast Furnace Slag composed of 30 to 40% Silica (SiO2) Alumina (AL202) 7 to 16% Lime (CaO) 32 to 45% and Magnesia (MgO) 5 to 15%. The oxides do not exist as free oxides but rather as silicates and alumino silicates which are chemicall inert. Since transportation costs limit the area of use, blast furnace slag can only be found in concrete products produced within 60 to 100 miles of a blast furnace operation. Even within these areas where slag is in heavy supply, quite often the use of slag is minimal for concrete aggregate and the major outlet is road base.

Jan 1, 1985

By J. H. Johnson

The report references reports and publications from 1975 to the present related to diesel underground mine air quality research undertaken by Michigan Technological University. Research results obtained on this contract are summarized in 5 different sections as follows: Section 1 - Development of a Systematic Approach to Monitoring, Data Analysis, and Interpretation for Diesel Mine Air Quality Control, Section 2 - Experimental Evaluation of LHD On-Board Air Quality Control Systems, Section 3 - Development of a Portable Self-Contained LHD Tailpipe Emissions Measurement Apparatus for NO , N0, CO, CO , and Particulate Matter, Section 4 Quantitative Analysis of Diesel and Coal particulate Matter by Laser Raman Spectro¬scopy and Section 5 - Development and Application to Detector Tubes of a Laboratory Method to Assess Accuracy of Occupational Diesel Pollutant Concentration Measurements.

Jan 1, 1985

By C. D. Jardine, D. G. Patton

Rapidly increasing energy costs and more rigid customer quality requirements necessitate improved control of pelletizing processes. With the introduction of dedicated microprocessor-based controllers, sophisticated control strategies are now possible. An application of this technology at Carol Project has resulted in fuel savings, improved pellet quality, and standardization of operating procedures. This was accomplished with no production loss by using a "building block" approach to design and equipment selection.

Jan 1, 1985

By C. F. de Mendonca, T. Kater, R. P. de Souza

Since 1976, Cia Vale do Rio Doce (CVRD) has carried out tests to develop a type of pellet made with an organic binder. Peridur is one binder that showed it could be used in industrial plants. Extensive tests were run in CVRD's pilot plant. The results are presented in this paper. The decision was made to carry out an industrial production of 50 ht (55,000 st) of pellets. The results are shown in this paper. No detrimental effects of the Peridur were observed in either the process or in product quality.

Jan 1, 1985

By H. W. Schreiber, G. R. Castle

INTRODUCTION The small mining company faces the dilemma of how to finance the development of its properties. Many of these small companies don't have the financial resources to pay for development costs from their own funds and frequently they do not even have the financial strength to permit them to borrow the money needed for development. A project financing can sometimes be arranged in such a way as to solve this dilemma. A typical project financing will not provide the answer to the "little guy's" problem because most project financings require that the sponsors of the project provide completion undertakings and sometimes other undertakings. These undertakings are often a prerequisite to obtaining financing, and if the sponsor is not financially strong enough to provide the comfort that the lenders require, then the sponsor will have difficulty obtaining financing no matter what undertakings are offered. However, with a little imagination and the right set of circumstances, a project financing can sometimes provide the solution to the small mining company's problem. The Strathcona Sound Project is unusually suited as a case study because the sponsor, Mineral Resources International Limited,(MRI) was able to arrange a project financing for the development of the project even though the lenders probably would not have been willing to loan a similar amount of money direct to MRI based on the full faith and credit of MRI's balance sheet. The way that MRI was able to arrange this financing makes for an interesting story. THE CASE In early 1974, MRI owned 100% of a small to medium sized zinc - lead - silver massive sulfide deposit (Property) located 475 miles north of the Arctic Circle less than two miles from deep water on Strathcona Sound which is a shipping zone in the Canadian Arctic. The Property was situated at a desolate location except for an Eskimo settlement (Arctic Bay) which was about 20 miles west of the Property. In other words, the project required that complete infrastructure would need to be installed in this far northern location. Independent reserve and feasibility studies (Study) had been completed on the Property which confirmed a total of 6,825,000 tons of reserves classified and summarized as shown below on Table I: [ ] These reserves were based on 229 diamond drill holes totalling 58,909 feet and were established on a cut-off grade of 7% zinc and a minimum mining height of seven feet. The overall mining recovery rate was estimated at not less than 85% and not more than 90%. The feasibility study indicated that it would cost an estimated $45,044,000 to develop an underground mine, a concentrator, a town-site, a power plant, storage facility, loading dock, a tailings disposal area and an airstrip on the Property with an annual capacity of 525,000 tons of ore per year. The construction period was expected to take two years and projected capital costs were broken down as set forth below on Table II:

Jan 1, 1985

Drilling in the south of the Rapahoe Sector at Greymouth Coalfield has demonstrated the existence of thick coal seams in the upper Rewanui Member. Seam correlation is handicapped by complex lithostratigraphy and laterally variable geophysical log profiles. An integrated investigation of coal measure stratigraphy, coal petrology, and proximate analyses, suggests a feasible model whereby most of the major seam intersections belong to a single horizon. Coal properties vary laterally in response to original swamp conditions, which are believed to have ranged from well-drained to ponded. A new model of peat accumulation is proposed for the northern Rapahoe Sector, whereby Upper Rewanui peat accumulation occurred on a flood plain between the levees of a major south southwest-flowing fluvial system in the east and the toe of a western alluvial fan.

Jan 1, 1985

By R. K. Komarek, F. E. Jr. Briber, G. M. Hanson, Fred D. DeVaney, J. H. Blake, C. L. Matson, T. E. Ban, N. E. Shields, R. D. Frans, R. B. Greenwalt

Metallurgically, the term agglomeration is used to describe processes whose goal is to form balls, briquettes, nodules, flakes, or other sized shaped particles from loose, usually fine, incoherent particles. In practice it includes such varying processes as the briquetting of coal dust and other substances, the balling and induration (heating) of such nonmetallics as cement, fluorspar, lightweight aggregates, etc. It includes such widely used processes as the sintering of nonferrous concentrates, such as those copper, lead, zinc, etc. The agglomeration of specific nonferrous metal concentrates is discussed in detail in the section of this handbook devoted to that particular metal. Agglomeration processes are of particular value to the iron and steel industry where the nature of the primary reduction process, the blast furnace, requires for best results a burden essentially free of fines. This is a change that has taken place since about 1960. Prior to that time many fine unsized ores were fed to the furnace. The development of the pelletizing process gave to the industry a chemically controlled closely sized product that increased the produc¬tion rate and reduced the costs so much that unsized fines are seldom used in modem furnaces. Steel plants produce many fine sized waste products such as fine dust (fine ore coke and gangue) and mill scale. These products, which have a valuable iron content, are usually sin¬tered directly at the plant for reuse. Fine sized ore concentrates are usually pelletized at the mine and shipped as pellets to the steel plant. Common practice in some areas producing natural high grade ores is to screen the ore at the mine to about 3/8 in. The oversize is shipped "as is" and constitutes blast furnace feed. The / in. may be shipped to the steel plant where it may be sintered or otherwise agglomerated. At some mines the fines may be pelletizied prior to shipment. With the development of large ocean ore carriers, and with the transportation of slurried concentrates or fines, a trend has developed of constructing large pelletizing plants or other types of agglomeration plants near large consumption centers (i.e., in the Netherlands or Japan) where ores of many types are brought together, ground if necessary, blended, and agglomerated. As an indication of tonnages of agglomerated materials produced, for iron materials alone (the largest share of the total) production in 1970 in the U.S. was Million gross ton Sinter 40.7 Pellets 43.1 Briquettes, nodules, & others 0.1 Total 83.9 During the 1960s, U.S. production of sinter rose from 40.3 million gross tons in 1961 to a high of 48.7 million in 1964, then settled back to almost the 1961 figure in 1970. Pellet production rose steadily from 14.4 million gross tons in 1961 to the 59.9 figure for 1975. Worldwide, sinter production in 1966 was estimated at 340 million mt (mainly in Europe, Russia, Japan, and the U.S.) and pellet produc¬tion the same year at 64 mt (primarily Canada and the U.S.). World pellet production capacity rose to 200 million tons in 1976.

Jan 1, 1985

By David K. Sitler

Continuing advances in manufactured diamond materials used in rock cutting tools have created a new generation of high production tools for mining. This paper will review the three major manufactured diamond products available for the mining industry as supplied by General Electric Company, Specialty Materials Department, and examine the ways in which these materials are employed. As an integral part of this examination, the economic impact of manufactured diamond tools will be evaluated. Time and again, one will find that the premium price of these tools is economically justified when compared to traditional tools.

Jan 1, 1985

By A. R. Hollbach

This paper presents a succinct overview of the Canadian coal situation. The topics treated specifically are: the rates of growth of coal supply and demand; the relationship between the coal and electricity generation industries which form its dominant market; the unique impact of nuclear generation on coal demand in Canada; and finally, a view of the developing technologies which will create opportunities for growth in the coal industry of the future. Resources The most important element of coal supply is the resource. The disposition of Canada's coal resources has a marked effect on their utilization, since industry in Canada has not generally developed around coal-fields. The distance from the major industrial centres of Ontario and Quebec to the major region of coal supply in Alberta and British Columbia has crested an economic barrier to the expansion of the use of domestic coal.

Jan 1, 1985

By Merline W. Van Dyke

The Surface Mining and Reclamation Act of 1977, PL 95-87 (The Act) granted the Office of Surface Mining (OSM) the duty of collecting fees from the active coal mining activities to be used in abating the hazards associated with abandoned coal mines. Since the passage of the Act, OSM has been instrumental in closing a multiple of mine hazards and in full cooperation with the states involved. Complete mine closures range from simply filling a subsidence hole to exodic designs costing thousands of dollars, such as in the case of the Portal Park swimming pool in Colorado Springs, Colorado. The Portal Park olympic sized swimming pool was built over an abandoned coal mine by a group of local citizens and given to the city of Colorado Springs. This pool receives the largest number of users each year. During the past four years, OSM has abated six mine related hazards in and around the pool. During the summer of 1982, the pool started tipping causing the pool waters to run out the west end. This pool tipping and the associated cave-in problems caused great concern to the city and the local users. This citizens concern generated a request from the city for OSM to assist in checking out the pool problems. Early in 1983, OSM initiated a driling program to investigate the subsurface voids. This drilling effort revealed several large voids within a few feet of the pool deck, with all voids inundated with ground water. Therefore, the void filling method favored the hydraulic backfilling needed to be confined to the area under the pool. This confining problem lead to the development of the gravel bulkhead cutoff walls to confine the backfilling effort to the areas under the swimming pool.

Jan 1, 1985

Improve mine refrigeration system efficiency while providing free electrical energy to mines. Approach Convert the potential energy of incoming mine water falling down long vertical shafts into electrical energy by means of a turbine-generator system located at the bottom of the mine shaft. How it Works Converting the energy of falling water into useful work is a well-developed engineering concept. Water flowing down long vertical pipelines into deep mines develops high pressure that can be used to operate a turbine-generator system at the bottom of the pipeline. A thermal energy recovery system of this type offers three advantages: 1. In systems without turbines, the potential energy of the water is converted to heat. The water temper-ture will automatically

Jan 1, 1985

By Paul M. Jr. Musgrove, Donald C. Moore

Conventional Smelting Practice Conventional copper smelting practice varies from smelter to smel¬ter, but generally consists of some or all of the following unit processes: roasting, smelting, converting, and fire refining. Roasting. Copper sulfide concentrates can be smelted directly or after an initial roasting step. Roasting is used in some smelters because roasting prior to smelting increases smelting capacity, less energy is required to melt hot roaster calcines than wet sulfide concen¬trates, roaster off gases are high in Sot concentration, 5-15% SO2, and some volatile impurities are removed from the concentrate prior to smelting. However, many smelters do not use roasters, because the problems associated with handling hot dry calcines outweigh the advantages mentioned. Concentrate roasting is performed in multiple hearth or fluid bed roasters. If the moisture is low, roasting can be performed autogenously, usually at 500-600°C. High roasting temperatures are avoided because excess oxidation of the iron compounds may lead to magnetite formation. Magnetite is detrimental to reverb operation because mag¬netite can combine with refractory minerals to form a highly viscous slag. This slag prohibits efficient matte-slag separation and leads to excessive copper losses. Also, magnetite can settle through the matte layer, deposit on the furnace bottom, and consequently reduce furnace capacity. Roasting is carried out only on sulfide concentrates prior to smelt¬ing in reverb or electric furnaces. For smelting processes, such as the flash and continuous that rely on the exothermic heat of oxidation of the sulfur minerals, roasting is not practiced. Reverberatory Smelting. The predominate copper smelting fur¬nace for the past 50 years has been the reverb. These furnaces are typically 100-120 ft long, 30-35 ft wide, and 12-15 ft high. A typical furnace layout is shown in Fig. 2. Refractory brick linings cover all internal surfaces of the furnace. Originally the flame was directed to reverberate or reflect off the furnace ceiling and melt the feed material. Current practice is to direct the flame down the furnace length to melt the concentrate. A method of charging the concentrates or calcines, generally along the side walls to minimize refractory erosion, is incorporated in the furnace design. The copper concentrates, calcines, and fluxes charged into the reverb undergo a series of complicated reactions as the temperature of the mixture increases. The reaction of the iron and copper sulfides with the oxygen in the furnace produces a molten Cu25-FeS mixture called matte. Copper smelting metallurgy is based on the fact that sulfur has a greater affinity for copper than for iron and most other common metals. Therefore, in a system containing copper, the copper will preferentially remain as a sulfide compound until all of the other metals have been oxidized. The oxidized metals combine with silica to form a silicate slag that floats on the matte and is removed from the system. Reverberatory furnace smelting chemistry can be approximated by the following chemical equations: FeS2 + O2 - FeS+ SO2 (1) The formation of FeS ensures that any copper present other than as sulfides will be reduced by the relationship: CuO2 + 2FeS + O2 - CuS + 2FeO+SO2 (2) or 2Cu +FeS - Cu2S + Fe (3) As the molten charge travels down the furnace, continued oxida¬tion of the iron minerals and sulfurization of the copper minerals occurs. When all of the copper has been converted to sulfides, the iron sulfides can then be further oxidized as: FeS + (3)2 O2 FeO + SiO2 (4) The FeO reacts with the silica added as flux in the furnace charge. A simplified equation is: FeO + SiO2 -FeO SiO2 (5) The iron silicate slag formed is skimmed from the surface at the end opposite the burners. The copper content of reverb slag is usually less than 0.6% Cu and is discarded. Matte is removed along the side wall and is taken to the converter for oxidation of the remaining sulfur and iron. The main objectives in reverberatory smelting are to produce a molten Cu2S-FeS matte containing 30-60% Cu and a throwaway slag. Production of matte permits complete conversion of all copper minerals into copper sulfides, which can migrate because of specific gravity differences, through the lighter slag layer. Also, the molten matte droplets collect the noble metals, gold and silver, as the matte settles in the furnace. The large settling area of the furnace provides enough separation time to produce a low grade slag, which can be discarded without further processing. High heat losses are associated with reverberatory smelting be¬cause of the large volume of gases sweeping through the furnace. Therefore, an outside source of heat is required to keep the smelting reaction going. Natural gas, fuel oil, or pulverized coal are used as this heat source.

Jan 1, 1985