Search Documents

By Ronald H. Church

As part of the Bureau of Mines health and safety research program in strata control, a ground-penetrating radar (GPR) system capable of pene-trating approximately 10 ft into the mine roof has been devised to identify anomalistic conditions. The GPR system consists of a transmitter with carrier frequencies of 250, 500, and 1,000 MHz, utilizing a dipole antenna, and a receiver, consisting of a dipole antenna fed into a sampler with a time base housed in a storage oscilloscope. A computer was utilized for data acquisition and data processing. Data analysis by computer enhancement revealed recognizable return ra-dar signatures from the middle man rock and main roof of the test site. These stratigraphic anomalies can be cataloged for recognizable fea-tures, which from the past history of the mine may have been shown to create strata control problems. Early recognition of such features could lead to immediate corrective actions and result in the saving of lives.

Jan 1, 1985

By D. H. Davidson

The basic principal in the ISL process involves the recovery of metal values by moving fluids through rock instead of moving rock. The process combines surface and sub-surface operations, with the economic performance controlled by four major factors; rates of fluid injection and production from wells; the rate of mineral solubilization; the volume of rock swept by the fluid; and the volume of solution processed through the system. This paper discusses various technical and economic parameters affecting these four factors and how they impact project costs.

Jan 1, 1985

By Fred Breu, Ronald E. Heuer

INTRODUCTION The Point Lepreau nuclear generating station was constructed in the late 1970's and early 1980's by the New Brunswick Electric Power Commission. Point Lepreau is a small peninsula on the north shore of the Bay of Fundy, about 55 km west of St. John, New Brunswick. Cooling water for the plant was to be obtained from and discharged into the Bay of Fundy by the system of shafts and tunnels illustrated in Fig. 1. The design engineer for the cooling water system was Albery, Pullerits, Dickson and Associates, Ltd., Toronto. Ferrera-Resco Ltd, Windsor, Ontario, was contractor for construction of the cooling water shaft and tunnel system, which was done between 1976 and 1979. The senior author was project manager for Ferrera-Resco, the junior author served as consultant to Ferrera-Resco on evaluation of certain geotechnical questions which arose during construction. SITE CONDITIONS Geology Except for limited overburden soils at the onshore shaft sites, the tunnels and shafts were constructed entirely in Triassic conglomerate, sandstone, and siltstone, with some shale interbeds. The bedding strike averaged about N6°E, The dip was to the west at about 30° along the Discharge Tunnel and 40° along the Intake Tunnel. Rock along the Intake Tunnel was mostly sandstone and siltstone and more thinly bedded, with RQ D generally in the range of 50 to 60%. Rock along the Discharge Tunnel tended to be coarser sandstone and conglomerate and more thickly bedded, with higher RQ D averaging about 80%. In addition to bedding joints, two other joint systems were identified

Jan 1, 1985

By Fernando A. Buttazzoni, Jorge C. Munita

INTRODUCTION To provide a background for discussing long-range financial and operational planning in the mining industry, we would like to begin by describing the role of planning in Codelco. Having taken part in Codelco's planning process since its inception in 1976, we believe that useful conclusions may be drawn for the experience we shall relate. Although Codelco is a state-owned copper producer with an important role in the Chilean economy, and is consequently very much at the core of national economic planning, the following discussion is not related to government planning but to planning in an operationally and commercially autonomous business concern with all the characteristics of a private enterprise. The only way in which Codelco differs from private business is that its financial successes or failures have a more direct impact on the countryls ability to participate in international trade, to meet its international financial commitments and to achieve economic and social growth. Thus, what follows is a presentation of the conceptual features of the planning process at Codelco and a description of the current state of planning in the company. It is understood that certain conceptual components are basic to any formal strategic planning process, and that the components of Codelco's planning process are therefore generally applicable in similar companies. First, the mission and scope of operation of the company must be defined, and goals must be set to achieve leadership in the business activities in which it engages. Having set this framework, the company must constantly scrutinize those internal elements and conditions that are essential to fulfill its mission and achieve leadership. In Codelco this means considering the actions which can best serve to define future capacities, taking into account declining ore grades and determining optimal production levels; watching over the productivity and skills of its labor force, and; keeping abreast of technological developments in non-ferrous mining and processing. If the company is proficient in these three areas, it will be cost efficient and there- fore competitive. Codelco must also watch over the business environment in which it operates. The company sells concentrate, blister and fire-refined copper, wirebar, cathodes and wire rod and must study the behavior of the market to attune its product mix to the demand existing for these various commodities in the international market and the copper consuming industries in general. By examining the internal and external environment in which the company conducts its production and commercial operations, it is able to diagnose its strengths and weaknesses, to identify the hazards it must overcome to stay ahead in the copper trade, and to take full advantage of business opportunities as they arise. CHARACTERISTICS OF CODELCO-CHILE Although our subject is Codelco, readers should keep in mind that there are many other copper producing operations in Chile, all in the private sector, and many valuable deposits that may be exploited in the future. Codelco is the only public sector copper producer, although there is one other state enterprise that operates smelting and refining facilities principally to serve a large number of very small producers of copper concentrate. In the mid-19801s, Codelco is the largest copper mining company of the world and the largest producer and exporter of copper with yearly sales totalling close to US$ 1.8 billion in 1983. Moreover, it is a highly profitable copper company at a time when the world copper industry as a whole has reported losses for several years. Codelco-Chile is a fairly new organization. The history of the four mining operations it manages is much longer: El Teniente was opened in 1912, Chuquicamata in 1915, Salavador in 1959 -- with installations of the old Potrerillos mine dating from 1927 -- and Andina in 1970. Having had separate owners, the management systems of the

Jan 1, 1985

By D. G. Osborne

Transportation cost is a key factor in both the profitability and competitiveness of coal marketing. With coal exportation growing rapidly, moisture control is important. Although in some cases, too much moisture reduction can lead to losses in transportation and pollution problems, there is normally justification for reducing moisture by mechanical means as much as possible. This paper reviews current technology of dewatering coal fines and examines the comparative capabilities of screens, filters, and centrifuges. Financial considerations are stated and implications of capital and operating costs on selection are discussed.

Jan 1, 1985

By By Staff

"Acid mine drainage can be controlled by water treatment, retardation of the pyrite oxidation reaction system, or enhanced prediction that allows preventive action to be taken. The Bureau of Mines is conducting research in each of these areas; the results of this research are summarized in the eight papers that comprise this volume. Field work to evaluate overburden analysis, alkaline injection, and bactericidal control of acid formation is described, along with two new inexpensive methods to treat acid mine water. These papers were prepared for an acid mine drainage technology transfer meeting held in Pittsburgh, PA, on April 3 and 4, 1985. INTRODUCTIONAcid drainage from coal mines is one of the most persistent industrial pollution problems in the United States. Over 5,000 miles of streams and rivers are adversely affected, primarily by underground mines that have been abandoned for decades. Meanwhile, at active mining operations and at sites where mining occurred after 1977, discharge water must be treated to meet fairly stringent regulatory limits--at a cost to the industry of over $1 million per day.The Bureau of Mines has a special responsibility to facilitate integration of mining and mineral processing with environmental safeguards. This responsibility is twofold: the development of techniques to reduce or eliminate environmental degradation, and the improvement of existing pollution control processes to make them more efficient and more cost effective. Research in acid mine drainage exemplifies the Bureau's concern for these environmental aspects of mining.This collection of papers summarizes much of the Bureau's recent research on acid mine drainage and will give the reader a sense of where the research is headed, in addition to providing details regarding new technology and recently acquired knowledge. The research papers address four basic objectives:"

Jan 1, 1985

By Gene Mattila

Each installed rock bolt costs in excess of 520.00. High cost in conjunction with the primary purpose of safety makes it only logical to install the highest quality anchors possible. Each bolt has designed support capabilities in axial, shear and fluctuating ground condition, if installed to manufacturers recommendations. The quality of anchor is not; however, only affected by material specifications, but by transportation, handling storage, installation procedure, machine performance and geology. The quality is not only affected by many variables, but reliability should be assured. Non-destructive methods of testing reliability are only available for several types of bolts.

Jan 1, 1985

Process control computers are finding ever increasing applications within the chemi-cal and mineral processing industries.To purchase a system which fulfils both the immediate and future needs of operating, technical and management groups, requires an appreciation of the capabilities of the system software and the constraints which apply to user development of application software. Early decisions are then required as to who will develop and maintain the software. Rules and conventions must be determined and adhered to if the end result is to be an orderly, well structured and properly documented system. Software development and maintenance represents a substantial, and often hidden, cost. Getting it right the first time will avoid either a major re-work, or having to live with a system which is extremely diffi-cult (at the worst, impossible) to trouble-shoot or modify.

Jan 1, 1985

By Francis G. Stehli

Though sedimentary rocks comprise only about five percent of the volume of the continental crust, they cover about 80% of its surface, serve as important reservoirs for fluids, contain reserves of non-metallic minerals, and have in general been extensively drilled. However, most drilling has been shallow in comparison to the thickness of the crust and such deep drilling as has taken place is very strongly localized in sedimentary basins. This may be seen by reference to Figures 1 and 2 which show the location of wells that drilled deeper than 15,000' [=] 4.6 km. (Figure 1) and those that drilled below 20,000' [=] 6.15 km. (Figure 2). It is apparent that, even in regions of sedimentary cover, direct exploration below six kilometers has been very restricted. In the case of the metamorphic and igneous rocks which make up 95% of the volume of the crust, direct exploration has been much less extensive in terms of both area and depth. The present state of our knowledge of the crust below a' thin surface layer stands in marked contrast to our growing present need for raw materials and the needs of future generations. It also stands in contrast to our need for enhanced, scientific knowledge of the deeper crust, its configuration, its present state, its hydrothermal systems,-its evolution, and its materials. Lessons learned in exploring the third dimension of the sea floor, the vigorous prosecution of seismic profiling, the development of testable models for hydrothermal systems and mineral deposits, the need for better understanding of heat flow, state of stress, earthquake mechanisms, and a host of other phenomena all suggest that it is time to launch a national program for scientific exploration of the crust which uses drilling to test important hypotheses developed on the basis of indirect evidence.

Jan 1, 1985

By P. Raffinot, C. H. G. Bushell, S. Hodgson, E. F. Milner, H. J. Bosshardt, N. Draper, D. E. Pickett, Edwin T. McKnight, J. Prieto

Zinc ranks third and lead fourth in world nonferrous metal conumption. In 1972 the free world consumed 3,333,000 mt of refined lead and 4,422,000 mt of refined zinc. The lead tonnage was divided into the following end uses: storage batteries (42%), lead allows (7%), pigments and chemicals (11%), cable sheathing (9%), gasoline additives (13%), pipes and sheets (8%), and miscellaneous uses (10%). The corresponding distribution of zinc uses in 1972 was galvanizing (39%), die casting (26%), brass (15%), rolled zinc (8%), oxide excluding American Process zinc made directly from concentrate (6%), and other uses (6%). The pattern of usage of lead and zinc varies considerably from country to country. During 1972 in the USA 49% of refined lead was consumed in storage batteries, 19% in gasoline additives, and only 3% in cable sheathing, whereas in the United Kingdom 28% of the lead was consumed in batteries, 14% in cable sheathing, and 14% in gasoline additives. For zinc the major US uses were die casting (41%) and galvanizing (37%), with about 3% consumed as rolled zinc; corresponding usages in the same applications in France were 12, 28 and 28% and in Australia 12, 67, and 3%, respectively. The outstanding resistance of lead to corrosion, its density, and

Jan 1, 1985

By Paul J. Lauricella

This presentation will summarize the basic safety components of an underground safety program. The program will begin with the first ingredient to a successful safety program, top management support, and continue through emergency services. Particular attention will be devoted to top management support for the safety program.

Jan 1, 1985

By J. C. Edwards

The Bureau of Mines developed a mathematical model that decribes the interaction of an automated breathing and metabolic simulator, or lung, with a self-contained· self-rescuer that is supplied compressed oxygen. The model can be used to predict the gas partial volumes of 0z, Nz, and COz in the lung and in the self-rescuer breathing bag for a prescribed metabolic state that characterizes the lung. Nonlinear rate equations are used to describe the temporal evolution of the gas partial volumes. A numerical procedure was established with a FORTRAN computer program to solve these equations, which correspond to a given metabolic state. Examples are presented of applications of the model to predict bag volume and bag oxygen concentration changes with time when the bag is controlled by an automated breathing simulator. Under certain restrictive conditions, the model equations can also be used to analytically pre-dict the time required for the bag to reach a maximum or minimum volume. The model equation in this latter case was extended to transi-tions between metabolic states, with transitions described as exponential growth or decay processes.

Jan 1, 1985

Data logged on mineral beneficiation processes during normal operation are analysed using time series (correlation and spectral) methods to identify the dynamics of the processes for on-line computer control. Recursive least squares estimation techniques are used to identify parametric models for a cassiterite flotation circuit and a coal washery. Identification problems such as the determination of model order, process time delays and the 'contamination' of the data by process recycle streams (feedback) are discussed. Typical results are presented in which optimised models are identified from data logged during normal operation.

Jan 1, 1985

By E. P. Deliac

The aim of this joint work between the French Coal Board and the Paris School of Mines is to be able to practically model the behaviour of a transverse drum cutting rock with picks. First a theoretical approach leads to the concept of cutting curves, giving forces and torque against penetration per drum revolution. Then experimental evidence, from full scale and reduced scale testing, validated and confirmed the theoretical shape of the curves. Finally practical applications are given, to improve the design or use of a shearer (or continuous miner). A micro-computer program is being developed to predict the cutting performances of a machine in certain conditions.

Jan 1, 1985

By Grant BPM

The lower levels at the CSA Mine have been developed to mine reserves between theNo.7 level and No.9 level.Work on major excavations for the project began during 1982 with the develop-ment of the crusher chamber, on No.9 level. The brows and walls were pre-dowelled to improve stability before mining by mass blasting techniques.At the same time work commenced on theextension of No.2 Shaft from No.7 level toNo.11 level. The shaft was stripped, using hand held drilling, to a raise bored holeand concrete lined to a diameter of 5.5 metres. Plats were developed at No.8 level, No.9level and the loading station.

Jan 1, 1985

By Stephen A. Swan

Bureau of Mines researchers have collected and evaluated rollover protective structures (ROPS) f or more than 10 yr. ROPS and falling object protective structures (FOPS) are required on specified mining machines under regulations of the Mine Health and Safety Administration (MSHA). Both ROPS and FOPS are required on mining machines used in surface coal mines and surface areas of underground coal mines (30 CFR 77.403 and 7 7.4 13a), and ROPS are required on mining machines used in metal and nonmetal mining operations (30 CFR 55, 56, and 57.9-88). This illustrated manual provides mine safety personnel, MSHA inspectors, and original-equipment manufacturers with guidelines and a check- list for inspecting ROPS being used in the field. The manual discusses specific requirements of the MSHA regulations and minimum inspection and maintenance checks for ensuring compliance with those regulations. An easily reproducible checklist is provided as an aid to the inspection of ROPS.

Jan 1, 1985

The Curragh mine has complex operating conditions. The mine operates in four seams to produce two coal qualities and is divided into five pits which have different qualities and coal preparation characteristics. The combination of all of the necessary controls to achieve maximum resource utilisation has necessitated the development of suitable software to assist the quality control engineering function. The required software had to be able to plan the optimum yield of coking coal whilst achieving the quality parameters for the coking coal and co-produced steam coal. The program has been designed to evaluate all of the mine faces available for coking coal production. The optimisation of coking coal production is planned and co-produced middlings steam coal determined. The optimum steam coal product is determined using the middlings in combination with bypass production.The computer software to carry out these functions has been designed by using an exploration data base as the raw data source. The program accesses this data and uses a coal preparation prediction program to determine the yield vs. ash relationship for each coal face. A linear program selects the optimum -combination based upon equal incremental ash values. The final output lists feed tonnages, coal preparation conditions, product tonnages and full coal quality data.

Jan 1, 1985

By J. G. Stuart, A. W. Cipkins, R. H. Thompson

Preliminary safe distances for blasting wiring from typical electromagnetic sources are presented. The distances are for underground coal mines and electromagnetic sources in the frequency range below 10 MHz. The distances are based on measurements performed at 3 locations in each of 3 coal mines. The measurement apparatus, measurement procedure, measurement results and the rationale used in the calculation of the safe distances are all described. The safe distances presented are dependent on the measurement results and their interpretation. More measurements are clearly necessary to establish the validity of the suggested distances.

Jan 1, 1985

By R. A. Irvine

The use of large vibrating screens presents unique challenges to the screen manufacturer, the plant designer, and the plant operator. The design of vibrating structures that span greater unsupported distances is critical to the reliability of a screen subjected to billions of fatigue cycles. Larger percentages of total plant production become dependent upon fewer, larger vibrating screens. Plant designers and operators must plan for equipment maintenance in a manner which optimizes the production availability of large vibrating screens.

Jan 1, 1985

By K. H. Nimerick

A recent study has attempted to identify properties of hard-to-float coal that make them responsive to froth conditioning. Froth conditioning is the process of chemically enhancing the hydrophobic surface character of fine coal particles to improve their recovery by froth flotation. Since its introduction, froth conditioning has enabled recovery of an additional 1.9 Mt (2.1 million st) of coal. This study correlates field results to chemical, physical, and petrographic properties. The most direct correlation relates the coal's oxygen content to its response to froth conditioning. The higher the oxygen content, the greater the benefits of froth conditioning.

Jan 1, 1985