Search Documents

By E. Yasar

This paper describes the use of the sand and plaster physical modelling technique to investigate the deformation around mine roadways using a variety of support methods in a particular form of stress field. The characteristics and conditions of coal measures rock were considered prior to the preparation of the models and the insertion of support The investigation has clearly shown how floor lift, roof failure and sidewall movements of mine roadways in laminated weak rock conditions gradually develops as a result of the increase in the stress and, also, how it is related to the level of support used.

Jan 1, 1995

Provide longwall operators with an alternative strategy for placement of gob gas ventholes to improve gas production.

Jan 1, 1995

By Denby B, Miles N. J

The underlying theory behind the construction of an on-line size analysis system is described together with an introduction to the Artificial Intelligent techniques that it is founded on. Previous systems based on more traditional technology such as edge detection and dilation algorithms have been restricted by the significant processing power they require, this has resulted in the production of systems with either reduced functionality or severe hardware requirements. A neural network approach offered a new perspective to the problem of size analysis; the ability of a network to learn and recognise subtle patterns in training data before on-line processing is initiated opened up the possibility for the production of a fully functioning practical system. The format of the training data had to be carefully analysed prior to its implementation in a neural network as the capability of a neural network solution depends as much upon a suitable data preparation as it does on the system architecture. To facilitate experimentation with various profile quantification techniques such as fourier and fractal analysis an Image Profile Analysis System was constructed (IPAS) in software on a personal computer. The IPAS system was produced with the aim of pre-processing image data to create data sets for experimenting with external neural network packages. The system allows the analysis of both real images obtained by image capture and simulated images created by an in-built in simulator. A measurement comparison scheme is also included together with a case study concerned with the frequency analysis of simulated images. The power of neural networks combined with the data compression provided by profiling removes the need for direct measurement of individual particles. This has obvious implications on the level of hardware necessary, and ultimately the expense of a stand alone system. The extrusive nature of data collection via an image analysis system will also permit simple installation of a shipped system; eliminating any requirement for interference with existing machinery.

Jan 1, 1995

By Thomas W. Camm

The U.S. Bureau of Mines has extensive experience estimating the cost of mining and mineral processing operations as an ongoing part of its information and analysis studies. With the increased interest in remediation of mine wastes, the USBM is developing a methodology to expand its cost estimating expertise to include costs of various remediation techniques applicable to mineral processing and mining wastes. By integrating waste remediation costs with existing USBM cost estimating systems for mine and mill operations, a comprehensive system for cost engineering studies will be developed.

Jan 1, 1995

By J. A. Muñoz, A. Ballester, C. Gómez, M. E. Sevillano, M. Figueroa

The electrochemical behavior of massive chalcopyrite (CuFeS2) electrodes has been studied in the absence and-in the presence of mesophilic microorganisms, using cyclic voltametry as analytical technique. The culture was principally formed for Thiobacillus ferrooxidans, Thiobacillus thiooxidans and Leptospirillum ferrooxidans. The results showed that the reactivity of the chalcopyrite gradually increased with the bacterial treatment. The anodic dissolution process of the chalcopyrite treated with microorganisms was related to the breaking of passive layers when the applied potential increased. The analysis of the surface products showed that the chalcopyrite was covered with a superficial film avoided its dissolution during the bioleaching test. So, the rest potential of the bioleached samples increased possibly as consequence of its superficial transformation.

Jan 1, 1995

By Kuruppu M

Geotechnical design plays a key role in mine design. A proper geotechnical design provides a safe working environment and facilitates efficient mining operation. There are mainly three design approaches: (i) judgmental, based on observational and experiential facts, (ii) empirical, based on empirical design formulae; and (iii) analytical, incorporating numerical analysis. Most design applications are based on the design methods one and two as mentioned earlier. However, complexities arise in deep underground mining operations and deep open pit mines. These complexities and difficult geological environment introduce more uncertainties and simple empirical formulae would not be adequate as a design tool. These situations require numerical modelling and analysis of the design problems including interpretation of the results obtained from the analysis. There are several tools available for performing the numerical modelling and analysis. A brief review of the available tools is provided. The authors selected ANSYS (a general purpose finite element analysis tool) for use in mining geomechanics and geotechnical design. This paper includes several examples demonstrating the applicability of this software in designing mining structures. The authors hope that the design examples will demonstrate the use of the numerical modelling and analysis applications in excavation design.

Jan 1, 1995

By Best R, Poulos H

This paper discusses the results of an Australian Coal Association Research Program project into the development of a routine analytical design method for roof support in underground mines. Simple design tools have been developed using a combination of elastic solutions, free body diagrams, and pile theory. An approach to the design of roof support in layered strata based on the ability of bolts to resist shear stresses is outlined. It is shown that pre-tensioning and angled installation are effective ways of increasing the effectiveness of bolts in such a situation. In highly stressed strata, macroscopic failure is predicted and a design based on the support of surcharged rock wedges is proposed. The methods are applicable to both coal and metalliferous mines.

Jan 1, 1995

By Muammer Kaya, Derya Oz

The main objective of this study was to remove printing ink from waste newspaper and improve the de-inked paper brightness as close as the unprinted paper by bleaching agents. This paper summarizes results of laboratory investigation into the de-inkability of newsprint printed with offset printing. Different chemicals and process parameters were varied to assess the effect on the brightness and cleanliness. The operations involved in de-inking process are briefly described and some of the problems being encountered are discussed.

Jan 1, 1995

By Fernando Concha, Arturo Barrientos, María Cristina Bustos

Manufacturers referred to high capacity thickening as a filtration operation rather than thickening in spite of the fact that it is performed in thickeners and that conventional thickeners can be operated as high capacity thickeners by changing the feeding level and operate it in a different manner. In this work we derive a phenomenological model for high capacity thickening based on mass and momentum balances. The difference with a conventional thickening is the presence of a surface source within the variable domain. The model can be used to design, simulate and to develop control strategies.

Jan 1, 1995

By G Liu

Seventy-nine gold deposits and prospects have been discovered in theJiamusi region of northeast China, and constitute one of the most important gold metallogenic belts in China. All these endogenic gold occurrences can be subdivided into three main deposit types: 1. porphyry related; 2. metamorphic-intrusive hosted, and 3. sediment-hosted deposit.   The first two types of gold deposit are spatially and temporally related to Mesozoic Yanshanian granitoid intrusions with hydrothermal activity channelled along crustal-scale fissures. The ultimate cause of the Yanshanian magmatism is considered to be the subduction of Pacific oceanic lithosphere beneath the Eurasian continent. In contrast, the chemical sediment-hosted deposit is typified by the Dongfengshan gold deposit, and genetically related to Proterozoic sedimentation and Mesozoic igneous activities.

Jan 1, 1995

By Lee W. Abramson, James E. Crawley

Caltrans is studying alignments for a 160-kilometer-long high speed ground transportation system from Los Angeles to Bakersfield across the Tehachapi Mountains. This link is needed to connect southern California with San Francisco by a short passenger rail service. None presently exists. The system will require tunnels and viaducts along the route with sections crossing two major active fault zones. High speed ground transportation technologies are being evaluated for achieving rail speeds of between 200 and 480 kilometers per hour. This paper presents the technical requirements for tunnels along the alternative routes being considered for the project.

Jan 1, 1995

By Barbara Fotta

This article examines health and safety trends during the past 10 years at Appalachian surface and underground bituminous coal mines. Data for Appalachia include Pennsylvania, West Virginia, Virginia and eastern Kentucky. These states account for more than 90% of the coal production in the Appalachian region. (Production, accidents and fatalities in Ohio, Maryland, Tennessee and Alabama are not included in computing Appalachian trends.) Trends for Appalachian underground mines are differentiated by size and mining method into three categories: - Small mines with fewer than 50 employees. - Large nonlongwall mines with 50 or more employees. - Longwall mines (mines with at least one longwall production face).

Jan 1, 1995

By S. L. Bessinger

The need for improved safety and productivity brought about the introduction of longwall mining to the Appalachian coal fields. These same forces continue to drive developments in modern longwall equipment and mining practices. Current initiatives to improve productivity and safety are focused on automation and the effects of scale in equipment design. Longwall roof-supports, shearers and face-conveyors have changed significantly. Panel layouts have evolved to include larger total tonnages and provide for more rapid development of gate-entries. These advancements have improved longwall productivity and new production records are continually being set. Roof supports Reliability is implicit in the quest for automation. It is impossible to automate equipment if it is not reliable. To a large degree, this has been the problem with longwall shield automation efforts. The "electronic control" of shields depends on the proper functioning of electronic equipment, electrohydraulic valves and full-flow service valves onboard every support.

Jan 1, 1995

The theme of this Annual Conference of The Australasian Institute of Mining and Metallurgy is in the form of a question: `Adding Value to our Resources - Our Future?' There are two ways of looking at this question. The first is to assume that any mineral or energy resource is worthless until it is identified, recovered and put on the market. In this sense all our current operations, be they open cut coal mines or aluminium smelters, are engaged in adding value. The question then becomes: what is the future of the minerals and energy resource industries with which we are familiar - will they grow or contract? The second way is to emphasis the value-adding aspect. The question is now one of whether or not our future depends on adding further value to resources we are currently selling.

Jan 1, 1995

By S. C. Sharma

The aluminium matrix composites with ceramic dispersoids can be separated by density difference concept. In the proposed work composite scrap is recycled using an oil fired furnace. The scrap is melted in the furnace and temperature is maintained below 740 degree centigrade. Because of the density difference the lighter dispersoids will float and heavier dispersoids will settle down. The clean melt is separated be removing the floating and settled disperssoils, and then filtering using ceramic filters.

Jan 1, 1995

By W. K. Tolley, D. G. Kotlyar

Oxidized sulfide minerals, commonly formed by weathering, are becoming increasingly important resources as primary sulfide deposits are depleted. Oxidation, in general, reduces selectivity and recovery in flotation. The objective of this research was to determine the mechanisms of oxidation and collector adsorption in sulfide systems as a step towards developing improved technologies for beneficiation of oxidized sulfides. Data from microcell flotation tests are combined with electrochemical and spectrophotometric measurements. The adsorption of ethyl xanthate (EX) on oxidized sulfides was characterized using AC impedance and voltammetry techniques, and correlated to flotation response. Oxidation resulted in an electrically resistive, nonporous surface layer. The floatability of chalcocite, chalcopyrite and pyrite was dependent on the extent of oxidation. Oxidation for one day or more at 65ºC suppressed chalcocite flotation. Oxidized chalcocite also inhibited flotation of chalcopyrite and pyrite. Oxidation caused decreased chalcopyrite flotation. Pyrite flotation, however, increased after oxidation.

Jan 1, 1995

By R. Lasmanis

"Washington State's diverse geological setting is reflected by its several types of porphyry Cu-Mo deposits. All are associated with calc-alkaline intrusions, and they range in age from Jurassic to Miocene.The largest is the Mount Tolman Mo-Cu deposit located in the Omineca Belt. It contains 2.18 billion tonnes of material averaging 0.093% MoS2 and 0.09% Cu. There are intermediate-size Mesozoic deposits in the Intermontane Belt. The Cascade volcanic arc hosts small- to medium-Tertiary deposits. Among these, of particular interest is the Sunrise breccia pipe, which has been explored over a vertical distance of 1000 m. It contains reserves of 64.6 million tonnes averaging 0.319% Cu and 0.071% MoS2 with significant tungsten values. The Glacier Peak deposits have potential resources of 1.7 billion tonnes averaging 0.334% Cu and more than 0.015% MoS2 and also contain tungsten. The Margaret deposit can be classified as a porphyry Cu-Au type; it has reserves of 200 million tonnes averaging 0.434% Cu, 0.0175% MoS2> 0.27 g!t Au and 1.92 g!t Ag. Drill intercepts of the North Fork deposit also show significant gold values.Mineralization and hydrothermal alteration of these deposits are typical of porphyry deposits, although some differences can be noted. The Mount Tolman molybdenum deposit contains topaz alteration zones and is transitional between a plutonic type and a Climax-type molybdenum system. Other deposits, such as the Kelsey, Mazama, North Fork, and Margaret, are low-sulphide systems that contain significant amounts of magnetite."

Jan 1, 1995

By Michael D. Balen

The plate-glass windows in the bus were cracked and mud-coated. Nevertheless, they afforded an excellent view of the many head-on collisions we narrowly avoided along the route from the Magadan airport to town. Apparently the driver thought the left side of the road was smoother than the right side, for he drove in the wrong lane at all possible times, even in the face of oncoming traffic. As far as we could tell, neither side of the road was any better than the other. Either way, we had to hang on just to stay in our seats. We careened past trucks and pedestrians, nearly always in the face of impending disaster. When the bus finally pulled into the parking lot of the Okean Hotel in Magadan, we had to thank the driver, not only for safely delivering his passengers, but also for the lasting first impression he gave us of the Russian Far East.

Jan 1, 1995

This paper sets out a number of means by which professionals can reduce or eliminate the risk of professional liability whether as directors, employees, partners, independent consultants or contractors. A relationship between client and professional is commonly cited as an example of a fiduciary relationship: the professional "undertakes or agrees to act for or on behalf of or in the interests of' the client "in the exercise of a power or discretion which will affect the interests of that other person in a legal or practical sense."2 As a fiduciary, a professional must ensure that his or her exercise of power does not result in a position of ascendancy or undue influence over the client. Also, a professional must avoid situations where there is scope for even the perception of potential conflict between his or her professional duty to the client and his or her own Interest.

Jan 1, 1995

By D. D. Banerjee, S. K. Kawatra, T. C. Eisele

To reduce their sulfur emissions, many coal-fired electric power plants use wet flue-gas scrubbers. These scrubbers convert sulfur oxides into solid sulfate and sulfite sludge, which must then be disposed of. This sludge is a result of reacting limestone with sulfur dioxide to precipitate calcium sulfite and calcium sulfate. The majority of the sludge is simply landfilled, but with increasing landfillimg costs this can cost the plant millions of dollars per year. As a result, this option is rapidly becoming less attractive. Producing marketable materials from the sludge is a far more promising avenue, provided that the products can meet the necessary specifications at a reasonable cost. In this paper, a method is described for using froth flotation and water-only cyclones to remove unreacted limestone from scrubber sludge. The water-only cyclone was found to be very effective for removing the coarser unreacted limestone, grinding ball chips, gravel, and similar coarse impurities. Froth flotation was found to remove fine unreacted limestone, with a minimum of reagent addition.

Jan 1, 1995